Interlogix TruVision TVD-6120VE-2 User manual

TruVision TVD-6120VE-2 /
TVD
-6125VE-2 Camera
User Manual
P/N 1072541C-EN • ISS 27JUL12

Copyright
©
2012 UTC Fire & Security. All rights reserved.
Trademarks and
patents
The
TruVision and Interlogix names and logo are trademarks of
UTC
Fire & Security.
Other trade names used in this document may be trademarks or
registered
trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance
Class A:
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated i
n a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in
a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.
ACMA compliance
Notice!
This is a Class A product. In a domestic environment this
product may cause rad
io interference in which case the user may be
required to take adequate measures.
European Union
directives
12004/108/EC (EMC directive):
Hereby, UTC Fire & Security
declares that this device is in compliance or with the essential
requirements and other
relevant provisions of Directive 2004/108/EC
2002/96/EC (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local supplier
upon
the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
Contact information
For contact information
, see www.utcfireandsecurity.com or
www.utcfssecurityproducts.eu
.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 1
Content
Product overview 2
Package Contents 2
Features 2
User guidelines 2
Product description 3
Installation 4
Mount the camera 4
Connect the cables 5
Adjust the lens 5
Programming 7
OSD control button 7
Access the Setup menu 7
Save changes 9
Select the lens type 9
Set shutter/AGC 9
Set white balance 10
Set backlight compensation (BLC) 11
Adjust the picture characteristics 12
Set ATR-EX level 12
Set motion detection 13
Set privacy area 13
Set Day/Night mode 14
Set image noise reduction 15
Set the camera ID 15
Set sync mode 16
Select the language 16
Reset camera settings 16
Specifications 17
Dimensions 17
Menu Map 18

2 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual
Product overview
The TVD-6120VE-2-N(-P)/ TVD-6125VE-2-N(-P) color dome camera uses a
digital signal processor (DSP) to process video signals. The camera includes a
microcontroller to provide high-quality images with high-color reproduction and
sharp pictures.
Package Contents
The package contains the following:
• Camera
• Hex key
• Drilling template
• Composite video BNC cable
• Screws
• Quick Start Guide
Features
The camera includes the following features:
• Super HAD II (hole accumulated diode) technology
• High horizontal resolution 600 TVL
• Smart digital control automatic BLC (backlight compensation)
• Digital WDR (wide dynamic range)
• Advanced auto exposure system for both fixed iris and auto iris lenses to
optimize the amount of light
• Internal synchronization
• Eight privacy mask areas to protect privacy concerns
• Signal-to-noise ratio better than 52 dB
• Long life and high reliability
• Isolated switching power 12 VDC and 24 VAC
User guidelines
• Program the camera settings as much as possible before mounting the
camera. Take appropriate safety precautions while completing programming
after installation.
• Always use a 12 VDC or 24 VAC UL listed Class 2 power supply to power the
camera.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 3
• Do not use the camera over the temperature range specifications: -10°C to
+50°C (14°F to 122°F)
• If the light source where the camera is installed experiences rapid, wide-
variations in lighting, the camera may not operate as intended.
WARNING: To reduce the risk of fire or electronic shock, do not expose the
camera to rain or moisture or open the back of the camera.
Product description
Figure 1: Product description
1. Dome cover
2. Screw hole
3. Base
4. OSD control button
5. Lens
6. IR LED
7. IR LED cover
8. Outlet hole
9. Power supply and video BNC cables
10. Composite video BNC cable
11. Focus adjustment
12. Zoom adjustment

4 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual
Installation
Please check the package contents and make sure that the device in the
package is in good condition and all the assembly parts are included.
To install the camera you will need to prepare the mounting surface, mount the
camera, make cable connections, and adjust the lens.
Note: Before installing, please ensure that the mounting surface is strong enough
to withstand three times the weight of the camera. If the mounting surface is not
strong enough, the camera may fall and cause serious damage.
Mount the camera
To mount the camera:
1. Prepare the mounting surface.
2. Remove the dome cover.
3. Secure the camera to the mounting surface with screws.
4. Remove the IR LED cover to adjust the lens and the viewing angle.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 5
Connect the cables
To make the cable connections:
1. Connect a 12 VDC or 24 VAC power supply to the power input.
2. Connect a coaxial cable from the camera’s BNC connector to a CCTV
monitor or video recording device.
Adjust the lens
The camera is mounted on a pan-tilt-twist (3-axis grimbal) rotating platform so
that it is easy to adjust the camera orientation.
To adjust the lens:
1. Rotate the panning table to adjust the panning position of the camera. The
adjusting range is from 0 to 355 degrees.
2. Rotate the tilting table to adjust the tilting position of the camera. The
adjusting range is from 0 to 75 degrees. Tighten the tilting table lock screw.
3. Rotate the lens to adjust the azimuth angle of the image. The adjusting range
is from 0 to 355 degrees.
Rotation 0-355°
Tilt 0-75°
Pan 0-355°
4. Adjust the lens to obtain the appropriate angle of view and the optimum focus.
Tighten the focus lock lever.
5. Replace the IR LED and dome covers on the camera.
6. Secure the dome cover with screws.

6 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual
Note: Ensure that the screws highlighted above with a “ ” have been tightened
securely to prevent water seepage.

TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual 7
Programming
Once the camera hardware has been installed, the camera can then be
configured.
Program the camera by attaching a standard video monitor to the system.
To connect the monitor:
1. Plug the monitor output cable to the video monitor output connector.
2. Connect the BNC cable to the video monitor.
3. Press Enter on the OSD menu button to display the Setup menu. See Table
1 for instructions on how to move the cursor.
OSD control button
The on-screen display (OSD) control button (see Figure 1) is a five-direction
joystick that lets you manually control the camera functions. Table 1 below lists
the OSD control button functions and describes their use.
Table 1: Using the OSD control button
Button
direction Description
Up
Moves the cursor upward to select an item
Left
Moves the cursor left to select or adjust the parameters of the selected
item.
Right
Moves the cursor to the right to select or adjust the parameters of the
selected item.
Down
Moves the cursor downward to select an item.
Enter
Press the center of the button to display the Setup menu. If the selected
item has its own menu, press the button to enter a submenu.
Access the Setup menu
The Setup menu provides access to the camera configuration options.

8 TruVision TVD-6120VE-2 / TVD-6125VE-2 Camera User Manual
Figure 2: The Setup menu
Table 2: Setup menu description
Menu item Description
Lens Defines autoiris or manual iris.
Shutter/AGC Defines the method of light control.
White Bal Defines the white balance (WB) set up.
Backlight Defines the highlight compensation (HLC) and backlight compensation
(BLC) set up.
Pict Adjust Defines the image quality functions.
ATR Defines the adaptive tone reproduction set up.
Motion Det Defines the motion detection set up.
Privacy Defines privacy mask set up.
Day/Night Defines the day/night (D/N) set up.
NR Defines the digital noise reduction level.
Camera ID Defines the camera ID displayed on-screen.
Sync Displays the current synchronization mode.
Language Defines the language of the OSD.
Camera Reset Resets the camera to factory default settings.
Save All Saves all configuration changes.
Exit Exits the menu and returns to live mode.
To access the Setup menu:
1. Press the OSD control button to access the Setup menu and its submenus.
2. Push the button up/down to move between menu options.
3. Push the button left/right to select an option.
4. Select Next to move to the next Setup menu screen and Back to return to the
previous Setup menu screen.
5. When in a sub menu, select Return to return to the previous menu.
6. To exit the Setup menu and return to normal camera operation mode, move
the cursor to Exit at the bottom of the screen and press Enter.