Intermec 6110 User manual

Quick Start Guide
P/N 962-054-007
Revision B
November 2000
6110 Hand-Held Computer
*962054007*
P/N 962-054-007 Rev B

6110 Quick Start Guide
-2
Packing List
Check to ensure that you receive these items:
6110 Hand-Held Computer
Li Ion Battery Pack
End User License Agreement
Product Warranty Card
End User Software License
Compliance Statement Insert

6110 Quick Start Guide
-3
Getting Started
Here are the main components that will get the most frequent
use in setting up your hand-held computer.
Power Status
I/O
ENTER
Reset Keys
Stylus
Frequently Used Components
Display
Backlight (Shift + 3)
1. Install the battery pack.
Installing Battery Pack
1
12
2. Charge the battery pack for 14 hours.

6110 Quick Start Guide
-4
Booting Your Computer
Using ATA Cards
1. Lift the ATA card door tab and flip open.
2. Slide the card into the slot closest to the display. The label
faces away from the display
Installing ATA Cards
1
1
2
For DOS Applications
1. Apply power by pressing the I/O (Resume/Suspend) key or
pressing the reset keys (gold, esc., zero) and holding for
three seconds simultaneously. The Power Status LED
will light .
2. The default load on the card displays these choices:
1. Pen*Key Utilities
2. DOS Command Prompt. Making this choice puts you to
the DOS prompt 6110 C:\>.
3. If you do not make a choice within 10 seconds, your 6110
automatically boots to the Pen*Key Utilities. From the
Utilities Programs, assuming you have the appropriate
host software and hardware, you can setup the commu-
nication options and also download your application.

6110 Quick Start Guide
-5
For Windows 95 Applications
1. Apply power by pressing the I/O (Resume/Suspend) key or
pressing the reset keys (gold, esc., zero) and holding for
three seconds simultaneously. The Power Status LED
will light.
Your hand-held computer begins booting Windows 95.
This will take about one minute.
2. Using the stylus, tap in the User Information and tap
Next.
3. Windows prompts you to accept the license agreement.
Either Tab over, or tap on the I accept the agreement
choice and then Next.
4. Key in the WIN 95 product ID number from the Certifi-
cate of Authenticity document.
"NOTE: The Certificate of Authenticity number comes with
your Windows 95 card.
Tap on End or press ENTER.
5. Windows may prompt you to update the clock. Tap in the
correct time and date and press ENTER.
6. You will probably be asked to enter your username and
password.
7. When the Pen Alignment Program comes up, tap on
each of the four crosshairs three times. You have 30 sec-
onds to complete the series of three taps (plenty of time!)
in each corner.
"NOTE: Pen Alignment is how close to the arrow on the
display that you must place your stylus to make the
entry or selection.
8. At the Finetune Calibration screen, either tap Save or
make the adjustments you want.
Panning
Panning is moving around within the display area to view
data. The program or application on your hand-held computer

6110 Quick Start Guide
-6
was designed on a full size pc display area. To see all that data
you must move around on that larger area with your smaller
display.
Remember these suggestions. First, the cursor will return to
the upper left-corner of the display. Second, to keep from get-
ting lost, put your stylus in the middle of the display area and
drag it to the right, left, upper, or lower edge. Dragging it in
this method takes you to the outer parameter of the display.
This shows you where you are on the display.
Panning Default
Your hand-held computer comes from the factory with panning
turned OFF. It is helpful to change the default to ON for set-
ting up your system. After you are pleased with the way your
application works change the default back to OFF.
Changing Default
1. Press I/O key to suspend your computer.
2. Copy System.ini to an ATA in the external slot or over
HyperTerminal to a pc.
3. Locate your Windows System.ini file.
4. Go into the non--panning display configuration file
and add a semicolon (;) in front of each line of code (do
not change the non-panning display configuration line).
5. Go into the Panning display configuration and re-
move the semicolon (;) from in front of each line of code
(do not change the Panning display configuration line).
Below is shown how to modify this code.
The column on the left is the default setting. Note that there is
not a semicolon in front of the lines of code (excluding the first
line that does contain a semicolon). The column of the right
shows the lines after you add the semicolon to each line.

6110 Quick Start Guide
-7
Non-Panning Default Setting Panning Default Setting
;-- non-panning configuration ;-- panning configuration
FrameSeq=0xa000 ;FrameSeq=0xa000
HWModule=sc4_2Bbpp.d11 ;HWModule=SC4_2BPP.d11
DisplayOrientation=1 ;DisplayOrientation=1
DisplayColumns=240 ;DisplayColumn=640
DisplayRow=320 ;DisplayRow=480
Panning=0 ;Panning=1
PanTrack=0 ;PanTrack=1
PanAbsolute=0 ;PanAbsolute=1
The below column on the left shows the lines of code altered to
allow panning. The right column on the right shows the default
changed for to enable the panning to occur.
Non- Panning Setting Changed Panning Setting Changed
;-- non-panning configuration ;-- panning configuration
;FrameSeq=0xa000 FrameSeq=0xa000
;HWModule=SC4_2BPP.d11 HWModule=SC4_2BPP.d11
;DisplayOrientation=1 DisplayOrientation=1
;DisplayColumns=240 DisplayColumns=640
;DisplayRow=320 DisplayRows=480
;Panning=0 Panning=1
;PanTrack=0 PanTrack=1
;PanAbsolute=0 PanAbsolute=1
6. Save the changes to System.ini file.
7. Copy file from external ATA or pc via HyperTerminal to
boot ATA. You have to reboot for the new settings to take
effect.
After you are finished making changes, go back and change the
default back to non-panning. To do this, of course, you reverse
the process both for the non--panning and panning display con-
figurations.

6110 Quick Start Guide
-8
Downloading from Host Computer
1. Install your hand-held computer into a dock.
2. Download program into your hand-held computer.
There are several ways to download your application. The fol-
lowing are just two examples.
EXAMPLE 1: You can load the program onto the ATA card, install
it into your hand-held computer, and select the pro-
gram from the directory.
EXAMPLE 2: You can also use Hyper Terminal if your system is
setup for this program.
Opening your Application
Press the I/O (Resume/Suspend) key. The Power Status LED
will light. Opening the application totally depends on your ap-
plication definition.