Intersil ISL2827xINEVAL1Z User manual

1
®
AN1290.2
ISL2827xINEVAL1Z Evaluation Board
User’s Guide
Introduction
The ISL2827xINEVAL1Z evaluation board is a design
platform containing all the circuitry needed to characterize
critical performance parameters of the ISL28270, ISL28271,
ISL28272 or ISL28273 Dual Instrumentation Amplifiers using
a variety of user defined test circuits.
The ISL2827x series of amplifiers are dual channel
instrumentation amplifiers optimized for 2.4V to 5V single
supplies. These devices feature an Input Range
Enhancement Circuit (IREC) which enables the inputs to
swing to the rails. The ISL28270 and ISL28273 maintain
CMRR performance from the positive rail down to within
50mV of the negative rail. The ISL28271 and ISL28272 can
swing 100mV beyond the rails. The output operation of all
devices is rail-to-rail. The ISL28270 and ISL28272 are
compensated for a minimum gain of 100 and the ISL28271
and ISL28273 are compensated for a minimum gain of 10.
Reference Documents
• ISL28270, ISL28273 Data Sheet, FN6260
• ISL28271, ISL28272 Data Sheet, FN6390
Evaluation Board Key Features
The ISL2827xINEVAL1Z is designed to be operated from a
single supply (+2.4VDC to +5VDC), or from split supplies
(±1.2VDC to ±2/5V). The board is configured for 2
independent instrumentation amplifiers connected for a
closed loop gain of 101 (ISL28270, ISL28272) or a gain of
10 (ISL28271, ISL28273) with inverting and non-inverting
high impedance terminated with 100k resistors to ground.
Each amplifier contains it’s own VREF input to establish an
input common mode reference. An ENABLE select switch is
provided for each amplifier to be used to save power by
powering the device down.
Power Supplies (Refer to Figure 1)
External power connections are made through the VSP (+V),
VSM (-V) and GND connections on the evaluation board.
For single supply operation, the VSM (-V) and GND pins are
tied together to the power supply negative terminal. For split
supplies, VSP (+V) and VSM (-V) terminals connect to their
respective power supply terminals. Resistors R32 and R33
are 0Ωbut can be changed by the user to provide power
supply filtering, or to reduce the voltage rate-of-rise to less
than ±1V/µs. Anti-reverse diodes D1and D2 protect the
circuit in the case of accidental polarity reversal.
Amplifier Configuration (Refer to Figure 2)
The schematic of each of the two op amps with the
components supplied is shown in Figure 2. The circuit
implements a differential input instrumentation amp with a
closed loop gain of 101 for the ISL28270 and ISL28272, and
10 for the ISL28271, ISL28273. The circuit can operate from
a single 2.4VDC to +5VDC supply, or from dual supplies
from ±1.2VDC to ±2.5VDC.The output common mode
reference is applied to the VREF pin, and has a range from
ground (VM) to VP.
C3
C4
D2
R33
VSM
0.1µF
VM
12
10µF
1
2D1
1
1
1
22
D3
1
2
VP
0.1µF
1
2
1 1
C5
R32 00
GND VSP
3
A
NC C
FIGURE 1. POWER SUPPLY CIRCUIT
-
+
-
+
IN+
IN-
FB+
FB-
RF
RG
VREF(x)
IN+(x)
IN-(x)
GND 100kΩ(ISL28270, ISL28272)
1kΩ
100kΩ
100kΩVOUT(x)
1/2 ISL28270, ISL28271, ISL28272, ISL28273
VP
-V
ENABLE
10kΩ
0Ω
VM
VCM
IN+
IN-
VREF 9.09kΩ(ISL28271, ISL28273)
FIGURE 2. BASIC AMPLIFIER CONFIGURATION
Application Note June 15, 2009
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2007, 2009. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.

2AN1290.2
June 15, 2009
User-selectable Options (Refer to Figure 3)
Component pads are included to enable a variety of user
selectable circuits to be added to the amplifier differential
inputs, the VREF input, and the amplifier feedback loop. A
voltage divider and filter option can be added to establish a
power supply tracking common mode reference at the VREF
input, or a coaxial connection to the amplifier FB+ pin can be
made at the FB+ BNC connector. The differential inputs have
additional resistor placements for adding input attenuation,
or to establish input DC offsets through the VREF pin.
FIGURE 3. COMPONENT-SELECTABLE OPTIONS
J9
R6R5
C3OPEN
DNPDNP VREFA
V+V-
J4
VREFA
1
R13 R15
R17
R18
R21
R22 R23
R20
R19
R16
R14
J8
J10
FB+A
-INA
+INA 0
0
0
DNP DNP DNP
DNP
DNP
1k
100k
100k
VREFA
ISL2827xINEVAL1Z Components Parts List
DEVICE # DESCRIPTION COMMENTS
C3, C5CAP, SMD, 0805, 0.1µF, 25V, 10%, X7R, ROHS Power Supply Decoupling
CFA, CFB, CLA, CLB CAP, SMD, 0805, DNP-PLACE HOLDER, ROHS Optional Amplifier Feedback Caps
Not Populated
C1, C2CAP, SMD, 1206, 1µF, 25V, 10%, X7R, ROHS Power Supply Decoupling
C4CAP-TANTALUM, SMD, D, 10µF, 35V, 10%, LOW ESR,
ROHS Optional VREF Filter Not Populated
D1, D2DIODE-RECTIFIER, SMD, MELF, 2 Ld, 50V, 1A, GPP,
ROHS Reverse Power Protection
U1ISL28270FAZ or ISL28271FAZ or ISL28272FAZ or
ISL28273FAZ INSTRUMENTATION AMP,16P, QSOP,
ROHS
R32, R33, RIN+A, RIN+B, RIN-A, RIN-B, RSA, RSB RES, SMD, 0805, 0Ω, 1/8W, TF, ROHS 0ΩUser Selectable Resistors
RIA, RIB. RES, SMD, 0805, 1k, 1/8W, 1%,TF, ROHS RIGain Resistors
R1, R2RES, SMD, 0805, 10k, 1/8W, 1%,TF, ROHS ENABLE Pull-up Resistors
R15 to R18 RES, SMD, 0805, 100k, 1/10W, 1%, TF, ROHS
R9, R12, R20, R22, R27, R29 CAP, SMD, 0805, DNP-PLACE HOLDER, ROHS User Selectable Resistors
Not Populated
RFA, RFB (ISL28271, ISL28273) RES, SMD, 0805, 9.09k, 1/8W, 1%, TF, ROHS RFGain Resistors - ISL28271,
ISL28272
RFA, RFB (ISL28270, ISL28272) RES, SMD, 0805, 100k, 1/8W, 1%, TF, ROHS RFGain Resistors - ISL28270
R3, R6, R10, R11, R13, R14, R19, R21, R23, R25,
R28, R30, RLA, RLB, RX.RES, SMD, 0805, DNP-PLACE HOLDER, ROHS User Selectable Resistors
Not Populated
S1, S2SWITCH-SEALED MINI TOGGLE, TH, 3P, SP,
ON/NONE/ON, GOLD Enable/Disable Select Switches
Application Note 1290

3
Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to
verify that the Application Note or Technical Brief is current before proceeding.
For information regarding Intersil Corporation and its products, see www.intersil.com
AN1290.2
June 15, 2009
ISL2827xINEVAL1Z Top View
Application Note 1290Application Note 1290

4AN1290.2
June 15, 2009
ISL2827xINEVAL1Z Schematic Diagram
DISABLE
ENABLE
ENABLE
DISABLE
CLOSE TO PART
CLOSE TO PART
DNP
100K
0
100K
OPEN
0.1UF
10UF
10K
0
DNP
100K
100
ROBERT POSPISIL
OPEN
0
0
DNP DNP
VP
MMBZ52XXB
0.1UF
1
10K
0
QSOP16
07/25/06
ALAN ERZINGER
VP
VM VP
VM
DNP DNP
100K
4.7K4.7K
DNP
0
DNP
0
VPVM
0
DNP
100K 100K
0
DNP
100
0
DNP
4.7K
VM
4.7K
VP
1UF
1UF
ISL2827XINEVAL1Z
OPEN
OPEN
DNP
DNP
DNP
DNP
-INA
1
2
3
4
5
VSM
1
GND
1
VSP
1
R1
RIN-A
RLA
R15
RSA
RSB
CLA
1
2
VOUTA
1
2
3
4
5
VOUTB
1
2
3
4
5
R11
VREFA
1
R32 R33
RIN+A
+INA
1
2
3
4
5
R16
R10
S1
2
3
1
S2
2
3
1
ENB
1
2
3
4
5
ENA
1
2
3
4
5
R2
RLB
CLB
1
2
C1
1
2
C4
1 2
D2
2 1
D1
2 1
D3
1
3
2
C3
1 2
C5
1 2
U1
1
10
11
12
13
14
15
16
2
3
4
5
6
7
89
R27 R20
R3
FB+A
1
2
3
4
5
R9
R19 R25
RFA
RFB
RIA
R21
R28
VREFB
1
R29
C2
1
2
R22
R30
R23
RIB
R12
R6
RIN-B
FB+B
1
2
3
4
5
-INB
1
2
3
4
5
R17
R18
R14
R13
RIN+B
+INB
1
2
3
4
5
CFA
1 2
CFB
1 2
RX
SHEET
HRDWR ID
UPDATED BY:
DATE:
DATE:
DATE:
TESTER
FILENAME:
MASK#
DATE: ENGINEER:
TITLE: RELEASED BY:
DRAWN BY:
Generic
Pack.
1
2
4
5
6
7
8
3
9
10
11
12
13
14
15
16
C
A
NC
Application Note 1290

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Intersil:
ISL28271INEVAL1Z