Intex 128644GS User manual

Zusammengeführte PDF Datei. Die Originale sind im folgenden Verzeichnis verlinkt. / Merged PDF File. Original files are linked in the following list. / Sloučený soubor PDF.
Originály jsou propojeny v následujícím adresáři. / Egyesített PDF fájl. Az eredetiek a következő könyvtárban találhatók. / Zlúčený súbor PDF. Originály sú prepojené v
nasledujúcom adresári. / Združena datoteka PDF. Izvirniki so povezani v naslednjem imeniku. / Spojena PDF datoteka. Izvornici su povezani u sljedećem imeniku.
128644GS - Krystal Clear sand filter unit SF90220RC
193GS 2
Air Valve For Water Revitalization Set 24
Hydro Aeration Technology 26
Service Center 28

193
GS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Krystal ClearTM Sand Filter Pump
Model SF90220T 4 m3
220 - 240 V~, 50 Hz, 190 W
Hmax 3.0 m, Hmin 0.19 m, IPX4
Max. Water Temperature 35 °C
IMPORTANT
SAFETY RULES
Please read, understand, and follow all
instructions carefully before installing
and using this product. Keep for future
reference.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change specifications and appearance, which may
result in updates to the instruction manual without notice.
OWNER’S MANUAL
©2017 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Trading Ltd.
- Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Trading Ltd., Intex Development Co. Ltd., G.P.O
Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European
Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union
durch/Intex Trading B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
For illustrative purposes only.
193-*GS-R0-1809

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 2
Warnings........................................................................................ 3
Parts References.......................................................................... 4-5
Setup Instructions ....................................................................... 6-13
Product Specifications................................................................. 8
Operating Instructions ................................................................. 14-16
Intex Pools Operating Time Table................................................ 17
Non-Intex Pools Operating Time Table........................................ 18
Maintenance.................................................................................. 19
Long Term Storage........................................................................ 19
Troubleshooting Guide................................................................. 20
Common Pool Problems............................................................... 21
General Aquatic Safety................................................................. 21
Limited Warranty............................................................................ 22
TABLE OF CONTENTS
RCD OPERATING INSTRUCTIONS
• Plug RCD into power outlet. Press RESET button on the RCD plug.
Indicator should be "ON".
• Press TEST button on the RCD plug. Indicator should be "OFF".
• Press RESET button for use. Do not use if test fails. Contact a qualified
electrician to determine cause of failure.
RESET
RESET
TEST
TEST RESET
RESET
RESET
TEST
TEST
TEST

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 3
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
• Always supervise children and those with disabilities.
• Children must stay away from this product and electrical cord(s).
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
• Assembly and disassembly by adults only. Cleaning and user maintenance must be performed by an adult above 18 years old
who is familiar with the risk of electric shock.
• Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit interrupter
(GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the receptacle is protected by
a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30 mA.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the
product.
• Always unplug the appliance on raining days or if leave it for long time (such as going out for holidays).
• The plug must be accessible after product is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other
equipment.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order
to avoid a hazard.
• To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to
electric supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Keep this product more than 3.5 m away from the pool.
• Keep the plug of this product more than 4 m away from the pool and at a height of 1.2 m at least.
• Position this product away from the pool, so as to prevent children from climbing on it and accessing the pool.
• Do not operate this product when pool is occupied.
• This product is for use with storable pools only. Do not use with permanently installed pools. A storable pool is constructed so
that it may be readily disassembled for storage and reassembled to its original configuration.
• To reduce the risk of entrapment hazard, never enter the pool if suction strainer component is loose, broken, cracked,
damaged or missing. Replace loose, broken, damaged, cracked or missing suction strainer components immediately.
• Never play or swim near suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
• To prevent equipment damage and risk of injury, always turn pump off before changing the filter control valve position.
• Never operate this product above the maximum working pressure stated on the filter tank.
• Hazardous Pressure. Improper tank valve cover assembly could cause the valve cover to blow off and cause serious injury,
property damage or death.
• This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC SHOCK, ENTANGLEMENT
OR OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent some common risks of water
recreation devices and do not cover all instances of risk and danger. Please use common sense and good judgement when
enjoying any water activity.

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 4
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
34
114
96
2
13
20
35
36
315
16
4
12*
7
8
32
11
33
17
10
5
19
18
" * ": Optional.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
21
22
23 24 25 26
28 29 31
**
**
37
21
22
23 24 25 39 27
28 41 30
38
38
40

SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
" * ": Optional.
When ordering parts, be sure to quote the model number and part numbers.
REF. NO. DESCRIPTION QTY. SPARE PART NO.
1 PRESSURE GAUGE 1 11720
2 TANK COVER & 6-WAY VALVE SET 1 11721
3 DRAIN OUTLET COVER 1 11131
4 CLAMP ASSEMBLY 1 11722
5 TANK O-RING 1 11728
6 SAND FILTER PUMP MOTOR INLET O-RING 1 10712
7 CENTER PIPE 1 11729
8 FILTER GRID 1 11730
9 DRAIN VALVE CAP 1 11456
10 DRAIN VALVE O-RING 1 11385
11 L-SHAPE O-RING 4 11228
12* HOSE WITH NUTS 2 11010
13 SAND FILTER INTERCONNECETING HOSE 1 11764
14 TRANSPARENT OUTLET ADAPTOR 2 11723
15 TRANSPARENT OUTLET ADAPTOR O-RING 4 11724
16 CLAMP PIN 1 11726
17 CLAMP SCREW 1 11727
18 L-SHAPE O-RING 1 11412
19 TRANSPARENT LEAF TRAP 1 11733
20 PUMP MOTOR 1 11735GS
21* PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED) 2 10747
22* HOSE O-RING 2 10262
23* STEP WASHER 2 10745
24* STRAINER NUT 2 10256
25* FLAT STRAINER RUBBER WASHER 2 10255
26* THREADED STRAINER CONNECTOR 1 11235
27* ADJUSTABLE POOL INLET JET NOZZLE 1 12369
28* ADAPTOR B 2 10722
29* STRAINER CONNECTOR 1 11070
30* POOL INLET JET NOZZLE 1 12364
31* STRAINER GRID 1 12197
32 10" SAND FILTER PUMP TANK 1 11731
33 10" SAND FILTER PUMP TANK BASE 1 11732
34 TRANSPARENT OUTLET ADAPTOR SCREW 4 11725
35 AIR RELEASE VALVE 1 10725
36 AIR RELEASE VALVE O-RING 1 10264
37* STRAINER GRID 1 12198
38* AIR JET VALVE 1 12363
39* INLET THREADED AIR CONNECTOR 1 12371
40* POOL INLET AIR ADAPTOR 1 12368
41* INLET STRAINER CONNECTOR 1 12365
42* AIR JET VALVE CAP (NOT SHOWN) 1 12373
Page 5
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents and become familiar with all the parts.

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
The strainer grid prevents large objects from jamming and/or damaging the filter pump. If
your pool has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The part numbers here onward refer to the parts depicted
in the Parts List section of this manual. To install, do the following:
1. In a counter-clockwise motion unscrew plunger valve
union from the threaded strainer connector (26) (see
drawing 1). Be careful not to lose the step rubber
washer (23). Place the plunger valve on the ground in a
safe place.
2. In a counter-clockwise motion unscrew the strainer nut
(24) from the threaded connector (26). Leave the flat
washer (25) on the connector (26).
3. Install the strainer and plunger valve at the lower
position of pool outlet (marked "+"). From the inside of
the pool liner insert the connector (26) into one of the
pre-cut holes with the washer remaining on the
connector to be placed against the inside of the liner
wall.
4. Before assembly, lubricate the threads with a petroleum
jelly. With the flat side of the strainer nut (24) facing the
outside wall of the liner in a clockwise motion screw the
strainer nut (24) back onto the threaded connector (26)
(see drawing 2).
5. Finger tighten the strainer nut (24) onto the threaded
connector (26).
6. Grasp the plunger valve assembly. Make sure the step
washer
(23) is in place.
7. In a clockwise motion screw the plunger valve union
back onto the threaded connector (26) (see drawing 3).
8. In a clockwise motion turn the plunger valve handle to
close position. Ensure the plunger valve is securely
closed. This will prevent water from flowing out during
filling of the pool (see drawing 4).
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP (optional)
Page 6
2
25
INSIDE
LINER WALL
24
1
23
2
1
3
1
2
4
INSIDE
LINER WALL
26 37

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
POOL INLET - NOZZLE & PLUNGER VALVE SETUP (optional)
Page 7
5
2
1
7
1
2
8
INSIDE
LINER WALL
9
WATER
FLOW
POOL
6
25 39 27
INSIDE LINER
WALL
24
38
1. In a counter-clockwise motion unscrew plunger valve
union from the inlet threaded air connector (39) (see
drawing 5). Be careful not to lose the step rubber
washer
(23). Place the plunger valve on the ground in
a safe place.
2. In a counter-clockwise motion unscrew the strainer
nut
(24) from the inlet threaded air connector (39).
Leave the flat washer (25) on the connector (39).
3. Install the nozzle and plunger valve at the upper
position of pool inlet. From the inside of the pool liner
insert the nozzle union (27 & 39) into one of the
pre-cut holes with the washer remaining on the
connector to be placed against the inside of the liner
wall.
4. Before assembly, lubricate the threads with a
petroleum jelly. Then, with the flat side of the
strainer nut
(24) facing the outside wall of the liner
in a clockwise motion screw the strainer nut (24)
back onto the inlet threaded air connector (39) (see
drawing 6).
5. Finger tighten the adjustable pool inlet jet nozzle (27)
and the strainer nut (24) onto the inlet threaded air
connector (39).
6. Grasp the plunger valve assembly. Make sure the
step washer
(23) is in place.
7. Screw the air jet valve (38) over the inlet threaded air
connector
(39).NOTE: Make sure the air jet valve
is securely tighten and facing up. In a clockwise
motion screw the plunger valve union back onto the
inlet threaded air connector (39) (see drawing 7).
8. In a clockwise motion turn the plunger valve handle
to close position. Ensure the plunger valve is securely
closed. This will prevent water from flowing out during
filling of the pool (see drawing 8).
9. Adjust the direction of nozzle head pointing away
from the pool outlet for a better circulation result
(see drawing 9).
10. The pool liner is now ready to fill with water. Consult
the above-ground-pool owner’s manual for filling
instructions.

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
11.2
Page 8
PRODUCT SPECIFICATIONS
SETUP INSTRUCTIONS
The sand filter removes suspended particles but does not sanitize your pool. Pool
chemistry is a specialized area and you should consult your local pool service specialist
for details.
TOOLS REQUIRED: One (1) Phillips screwdriver
Pump location and mounting:
• The system must be installed on a solid level and vibration-free base.
• Provide a location protected from the weather, moisture, flooding and freezing
temperature.
• Provide adequate access, space and lighting for routine maintenance.
• Pump motor requires free circulation of air for cooling. Do not install the pump in a
damp or non-ventilated location.
A team of 2 or more people is recommended for setting up this product.
The appliance is intended only for household use.
Leaf trap setup:
1. Make sure the pump o-ring (6) is in place. In a clockwise motion screw the leaf trap (19)
onto the motor inlet (see drawing 10).
Sand tank installation:
1. Place the tank support base at the selected location.
2. Place the tank on the tank support base (see drawing 11.1).
10
19
6
11.1 11.3
Power: 220-240 Volt AC
Wattage: 190 W
Maximum working pressure: 1.4 bar (20 psi)
Effective filtering area: 0.05 m2(0.54 ft2)
Pump flow rate (at pump outlet): 4.5 m3/h (1200 GPH)
Recommended filtering media: No. 20 silica sand or glass sand. Particle size
(Not included) range 0.45 to 0.85 mm (0.018 to 0.033 inches).
Uniformity Coefficient less than 1.75.
Recommended filtering media quantity: No. 20 silica sand 12 Kg (26 Lbs) or glass sand
8.5 Kg (18.5 Lbs).
Limited Warranty: see “Limited Warranty”
NOTE: NOT SUITABLE FOR USE WITH KCP-LOW -SALT AUTOMATIC SALTWATER SYSTEM
(MODEL 6110/6220).

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 9
SETUP INSTRUCTIONS (continued)
3. In a clockwise motion screw the center pipe (7) onto the filter grid (8) securely by hand (see
drawing 11.2).
4. Vertically insert the filter grid and center pipe assembly into the tank. Ensure filter grid
assembly is securely fitted to the bottom of the tank, and the center pipe is vertically
centered inside the tank (see drawing 11.3).
Sand loading:
IMPORTANT: Use No. 20 silica sand or glass sand with particle size range 0.45
to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75.
Only use the filter media specified by the manufacturer.
NOTE: Before loading the tank with sand, ensure the sand filter grid and center pipe
assembly is securely in place on the tank bottom, and the center pipe (7) is vertically
centered inside the tank.
1. To prevent sand from falling into the center pipe top opening when pouring the sand, cover
the center pipe top opening with a cup or similar object (see drawing 12).
2. With one person holding the center pipe to keep it centered, pour the sand into the tank at a
slow rate manually to prevent the filter grid assembly from shifting (see drawing 13).
13 14
3. Fill the tank approximately half way first to evenly distribute the sand inside the tank, then fill
the tank with some water to provide a cushioning effect when the remaining sand is poured
in. This prevents the filter grid (8) from excessive shock (see drawing 14).
4. Sand shall be filled between the “MAX” and “MIN” marked gauge on the center pipe. Evenly
spread and level out the sand by hand (see drawings 14 & 15).
5. Remove the protective cup from the center pipe top opening.
6. Wash away all sand around the top edge of the tank.
IMPORTANT: Ensure the center pipe (7) remains centered after sand loading is completed
before proceeding to the next step.
MAX
MIN
MAX
MAX
MIN
MIN
15
7
12
7

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
SETUP INSTRUCTIONS (continued)
WARNING
Improper tank valve and clamp assembly could cause the valve and clamp to
blow off and cause serious injury, property damage or death.
Page 10
6-way valve installation:
1. Make sure the tank o-ring (5) is in place (see drawing 16). NOTE: Ensure the tank o-ring is
free of sand or debris.
2. Lower the 6-way valve cover over the tank slowly, and ensure the bypass pipe protruding
underneath the 6-way valve cover fits securely into the center pipe (7) top opening (see
drawing 17). Make sure the tank o-ring is securely fitted between the top edge of the tank
groove and the 6-way valve cover edge. IMPORTANT: Ensure the 6-way valve cover ridge
is aligned with the groove on the tank rim.
IMPORTANT: There are three hose connection ports on the 6-way valve, ensure the
outlet connection (from filter to the pool) on the valve is facing towards the pool (see
drawing 18).
3. Remove the screw, and install the clamp around the tank and 6-way valve flanges, then
replace the screw and use a phillips screwdriver (not included) to tighten it (see
drawings 18 & 19).
19
17
18
WATER
OUTLET
WATER
INLET
16
517
WATER
INLET
WATER
OUTLET
TO
DRAIN
DRAIN
VALVE
CAP
DRAIN VALVE CAP

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 11
SETUP INSTRUCTIONS (continued)
Motor installation:
1. Place an L-shape o-ring (18) on the pump motor outlet. In a clockwise motion connect the
sand filter interconnecting hose (13) to the pump motor outlet (see drawing 20).
2. Connect the pump motor unit to the tank support base (see drawing 21.1). NOTE: Ensure
the leaf trap water inlet hose connection is facing towards the pool.
IMPORTANT: Some countries, especially in the European community, require the
product to be secured to the ground or to a base in a permanent upright position.
Check your local authorities to determine if there is a regulation in your area
regarding above-the-ground swimming pool filter-pumps. If yes, then the product can
be mounted to a platform using the two holes located in the base. See drawing 21.2.
The product can be mounted on a cement base or onto a wooden platform to prevent
accidental falling over.
• The mounting holes are 6.4 mm in diameter and spaced 100 mm apart.
• Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
3. Place an L-shape o-ring (11) on the 6-way valve inlet connection. In a clockwise motion
connect the sand filter interconnecting hose (13) to the 6-way valve inlet connection (see
drawing 22).
21.1
22
13
20
13
21.2
100 mm

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 12
SAND FILTER PUMP HOSE CONNECTION SETUP
The 6-way valve has three hose connection ports.
1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose to the lower
connector with the strainer. Ensure the hoses are securely tightened.
2. Connect the second hose (12) between the 6-way valve water outlet and the upper connector
with the inlet-nozzle. Ensure the hoses are securely tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be directed to
a proper draining receptacle using a hose or pipe (not provided). Remove the drain cap before
attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.
WARNING
• Keep this product more than 3.5 m away from the pool.
• Keep the plug of this product more than 4 m away from the pool and at a
height of 1.2 m at least.
• Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
According to the International Standard, IEC 60364-7-702, on electrical installation of swimming
pools and other basins equipment, the following installation distances must be respected:
• The filter pump must be positioned more than 2 m away from the pool walls.
• The power cord plug to the 220-240 volt electrical power source of the filter pump must be
positioned more than 3.5 m away from the pool walls.
Check your local authorities to determine the appropriate standard and requirements for “electrical
installation of swimming pools and basins equipment”. The following table is for reference only:
International
France
Germany
The Netherlands
Country/Region Standard Number
IEC 60364-7-702
NF C 15-100-7-702
DIN VDE 0100-702
NEN 1010-702
WATER INLET
WATER INLET
WATER LEVEL
OUTSIDE
LINER WALL
PLUNGER
VALVE
L-SHAPE
O-RING
L-SHAPE
O-RING
TO
DRAIN
AIR
RELEASE
VALVE >3.5M
>4M (ILLUSTRATION NOT TO SCALE)
AIR JET VALVE
INLET THREADED AIR
CONNECTOR
RCD

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 13
SAND FILTER PUMP HOSE CONNECTION SETUP (continued)
For INTEX pool with 1-1/4” (32mm) connections/hoses:
Make sure the air jet valve (38) is securely tighten onto the pool inlet air adaptor (40) and facing
up.
For NON-INTEX pool:
Connect the hose (12) to the pool inlet/outlet connection with a large hose clamp. Tighten
securely.
POOL
LARGE HOSE
CLAMP
12
3
41
28
(Adaptor B) 40 38 30 29 31
23 28
(Adaptor B)
23

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 14
OPERATING INSTRUCTIONS
• Risk of electric shock. Connect this product only to a grounding type receptacle
protected by a ground-fault circuit interrupter (GFCI) or residual current device (RCD).
Contact a qualified electrician if you cannot verify that the receptacle is protected by a
GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum
rate of 30mA. Do not use a portable residual current device (PRCD).
•To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors
or converter plugs to connect unit to electric supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your
hands are wet.
•
Never operate this product above the maximum working pressure stated on the filter tank.
• Always switch off pump before changing the 6-way valve position.
• Operating this product without water flowing through the system can cause a build up
of hazardous pressure which can result in an explosive situation, serious injury,
property damage or death.
• Never test this pump with compressed air. Never operate the system with water
temperature above 35 °C (95 °F).
Valve Position Function Water Flow Direction
FILTER
(see drawing 23) Normal filtration and regular vacuuming
of pool From pump through filter media to pool
BACKWASH
(see drawing 24) Reverses water flow to clean filter
media From pump through filter media to valve waste/drain outlet
RINSE
(see drawing 25)
For initial startup cleaning of the sand, and
leveling the sand bed after backwashing
From pump through filter media to
valve waste/drain outlet
WASTE
(see drawing 26) For vacuuming directly to waste,
lowering pool level or to drain the pool From pump to valve waste/drain outlet bypassing the filter media
RECIRCULATE
(see drawing 27) For circulating water back to pool
without going through the filter media From pump through valve to pool bypassing the filter media
CLOSED
(see drawing 28)
Shuts off all flow to filter and pool
“Do not use this setting with pump running”
6-way valve positions and function:
WARNING
23 24 25

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 15
Initial startup and operation:
Before operating, be sure that:
• All the hoses have been connected and tightened securely, and correct amount of filter sand
have been loaded.
• The entire system is connected to a grounding type receptacle protected by a ground-fault
circuit interrupter (GFCI) or residual current device (RCD).
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should never be
on when the valve is in the closed position. If the pump is operated with
the valve closed, explosive situation could exist.
1. Turn both plunger valve handles fully counter-clockwise until
they stop. This opens the valves to allow water to flow into
the sand filter pump.
2. Release air from the system - Ensure the drain/waste outlet
on the 6-way valve is not covered and directed to a proper
draining receptacle, and the pump is off. Turn the 6-way
valve to the “N” position and unscrew the air release valve
(36) from the motor housing (see drawing 29). When water
starts flowing out of the air release valve hole, close the air
release valve back.
3. BACKWASH - Ensure the pump is off, depress the 6-way
valve and turn it to the “BACKWASH” position (see
drawings 24 & 30).
IMPORTANT: To prevent damage to the 6-way valve,
always depress the valve handle before turning. Always
switch off pump before changing the 6-way valve
position.
4. Switch on the pump (see drawing 31). Water is circulating
backward through the sand media and to waste/drain outlet.
Backwash until a clear flow of water is observed in the waste/
drain outlet or through the transparent outlet adaptor.
NOTE: The initial backwash of the filter is recommended to
remove any impurities or fine sand particles in the sand
media.
30
1
2
N
29
36
31
OFF
ON
TIMER
26 27 28

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 16
OPERATING INSTRUCTIONS (continued)
5. Switch off the pump, change the 6-way valve to “RINSE” position (see drawing 25).
6. Switch on the pump and run the pump for about one minute to level out the sand bed after
backwashing the sand media.
7. Switch off the pump, change the 6-way valve to “FILTER” position (see drawing 23).
8. Switch on the pump. The system is now operating in the normal filtering mode. Run the pump
until the desired pool water clearance is obtained and no more than 12 hours per day.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash frequently due to
unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and
impurities from the pool water, the accumulated dirt in the sand media will cause the
pressure to rise and the flow to diminish. If there is no vacuuming device attached to the
system and the pressure gauge reading is in the yellow zone it is time to backwash the sand
media, see “BACKWASH” under “initial startup and operation” section.
Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also cause the
flow to diminish and the pressure to rise. Remove any vacuuming device from the system and
check if the pressure gauge reading has dropped from the yellow zone to the green zone.
10.Monitor the pressure gauge reading, and check that the inlet and outlet openings are not
obstructed on a weekly basis. If the pressure gauge indicates yellow it is time to backwash
the filter media. IMPORTANT
The filter pump running time should be 1 hour longer than the required operating time
of the Saltwater System.
Operating the system under “TIMER” mode or manually:
To operate the sand filter pump in “FILTER” mode under “TIMER” control:
A. Set the timer dial to the desired operating hours. See operation time table (see
drawing 32).
B. Turn on the pump by pressing the switch to “ ” position, the sand filter pump is now
filtering the water and will stop after the operating hours are completed. The built-in timer
will now operate for the number of hours selected at the same time each day.
C. Operating hours can be re-adjusted if necessary. Follow step A – B.
To operate the sand filter pump manually (without the “TIMER” mode):
A. Turn on the pump by pressing the switch to “-” position, the sand filter pump is now
filtering the water.
B. To turn off the pump, press the switch to “O” position.
32
TIMER OFF ON
TIMER DIAL
(HOURS)

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 17
INTEX POOLS OPERATING TIME TABLE (WITHOUT INTEX SALTWATER SYSTEM)
This table shows the required operating time for average use of the sand filter pump with
above ground pools.
If the system is attached to an “Intex Saltwater System” unit, the filter pump running time
should be longer than the required operating time of the Intex Saltwater System unit.
Pool Size
Water Capacity (Calculated
at 90% for Frame Pool and
80% for Easy Set & Oval
Pool)
Sand filter pump
operating time
(For one cycle)/
(Hours)
(Gals) (Liters)
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
15' x 33" (457cm x 84cm)
2587 9792 4
15' x 36" (457cm x 91cm)
2822 10681 4
15' x 42" (457cm x 107cm)
3284 12430 4
15' x 48" (457cm x 122cm)
3736 14141 4
16' x 42"(488cm x 107cm)
3754 14209 4
16' x 48" (488cm x 122cm)
4273 16173 6
18' x 42" (549cm x 107cm)
4786 18115 6
18' x 48" (549cm x 122cm)
5455 20647 6
18' x 52" (549cm x 132cm)
5894 22309 6
ROUND
METAL
FRAME POOL
12' x 36" (366cm x 91cm)
2086 7896 4
15' x 36" (457cm x 91cm)
3282 12422 4
15' x 42" (457cm x 107cm)
3861 14614 4
15' x 48" (457cm x 122cm)
4440 16805 6
16' x 48" (488cm x 122cm)
5061 19156 6
18' x 48" (549cm x 122cm)
6423 24311 8
18' x 52" (549cm x 132cm)
6981 26423 8
ULTRA FRAME
POOL
12' x 36" (366cm x 91cm)
2086 7896 4
14' x 48" (427cm x 122cm)
3861 14614 6
16' x 48" (488cm x 122cm)
5061 19156 6
18' x 48" (549cm x 122cm)
6423 24311 8
18' x 52" (549cm x 132cm)
6981 26423 8
GRAPHITE GRAY
PANEL POOL SET™
16'8" x 49" (508cm x 124cm)
5061 19156 6
18'8" x 53" (569cm x 135cm)
6981 26423 8
OVAL FRAME
POOL
18' x 10' x 42" (549cm x 305cm x 107cm)
2885 10920 4
20' x 12' x 48" (610cm x 366cm x 122cm)
4393 16628 6
24' x 12' x 48" (732cm x 366cm x 122cm)
5407 20465 6
28' x 12' x 48" (853cm x 366cm x 122cm)
6420 24300 8
RECT. ULTRA
FRAME POOL
15' x 9' x 48" (457cm x 274cm x 122cm)
3484 13187 6
18' x 9' x 52" (549cm x 274cm x 132cm)
4545 17203 6

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 18
NON-INTEX POOLS OPERATING TIME TABLE
This table shows the required operating time for average use of the sand filter pump with
above ground pools.
Water Capacity
Sand filter pump operating
time (For one cycle)
(Gals) (Liters) (Hours)
3000 11355 4
4000 15140 4
5000 18925 6
6000 22710 6
7000 26495 8
8000 30280 8

193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220T SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 09/15/2017
English
Page 19
1. Before emptying your pool for long term storage, or relocation, be sure the water is directed
towards an acceptable drain water receptacle away from the house. Check local regulations
for specific directions regarding disposal of swimming pool water.
2. Switch off the unit, and disconnect power cord from electrical outlet.
3. When the pool is empty, disconnect all hoses from pump and plunger valves and remove the
strainers/plunger valves from the pool wall.
4. In a counter clockwise motion unscrew the drain valve cap (9) from the drain valve to
thoroughly drain the tank. The drain valve is located at the bottom of the filter tank.
5. Disassemble the pump motor from the tank base.
6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.
7. Coat the following o-rings and washers with petroleum jelly for long term storage:
• L-shape o-rings
(11 & 18).
• Pump hose o-rings (22).
• Strainer valve assembly step washers (23).
• Flat strainer rubber washers (25).
8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve top “N”
position. This allows the water to drain from the valve. Leave the 6-way valve in this inactive
position.
9. It is best to place all dry pieces and pump motor in the original packaging for storage. To
avoid condensation or corrosion problem, do not cover or wrap pump motor with plastic bags.
10. Store the pump motor and accessories in a dry place. The storage's temperature should be
controlled, between 0 degrees Celsius (32 degrees Fahrenheit) and 40 degrees Celsius
(104 degrees Fahrenheit).
11. Cover the tank with a tarpaulin or plastic sheet to protect it from the weather.
POOL CARE & CHEMICALS
• All pools require care to keep the water clear and hygienically clean. With proper chemical
control, your filter will help attain this objective. Consult your pool supply dealer for
instructions regarding the proper use of chlorine, algaecide and other chemical agents
required for sparkling clear water.
• Keep pool chemicals away from children.
• Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could occur.
• Daily pH checking and chemical treatment of the water is very important and cannot be
overemphasized. Chlorine, algaecide and maintenance of proper pH levels are required when
filling the pool as well as during the season. Consult your local swimming pool supply store
for instructions.
• The season's first filling of the pool may have brackish water requiring extra water additives
and extra filtering time. Do not allow swimming in pool until the pH level is balanced. Consult
your local swimming pool supply store for instructions.
• Chlorinated water may damage lawns, gardens or shrubbery as children play in the pool and
splash water outside the pool. Lawn areas underneath the pool liner will be destroyed. Note
that some types of grass may grow through the liner.
• Filter run time depends on pool size, weather and usage level. Experiment with various run
times so as to produce clean clear water.
• European standard EN16713-3 lists some additional pool water quality and water treatment
information that can be found at www.intexcorp.com/support.
LONG TERM STORAGE & WINTERIZATION
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always follow
the chemical manufacturer’s directions, and the health and hazard warnings.
CAUTION
Allowing the water to freeze will damage the sand filter and void the warranty.
If anti-freeze solution is needed, use only propylene glycol. Propylene glycol is
non-toxic and will not damage plastic system components; other anti-freezes
are highly toxic and may damage plastic components in the system.