Intex Quick-fill ap622 User manual

166

(166IO) AP622 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 09/18/2017

READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT

INTEX®OWNER'S MANUAL

Quick-Fill™ Electric Air Pump, Model AP622

220 – 240 Volt ~ 50 Hz; 12 Volt DC; Rechargeable Battery

166-*IO-R0-1809

•Adult use only.

•Do not drop unit into water or expose unit to rain or water.

•Do not direct air stream at face or body.

•Do not operate for more than 10 minutes at a time. Unplug and

let cool at least 30 minutes.

•Unplug unit when not in use.

•Do not obstruct vent holes or open source.

•Do not insert objects into the inflation or deflation connector.

•To reduce the risk of electric shock, do not expose to rain.

Store indoors.

•This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the

appliance in a safe way and understand the hazards involved.

• Children shall not play with the appliance.

• Cleaning and user maintenance shall not be made by children

without supervision.

• The appliance is only to be used with the power supply unit

provided with the appliance. It must only be supplied at safety

extra low voltage corresponding to the marking on the

appliance.

FOLLOW THESE RULES AND ALL INSTRUCTIONS TO

AVOID PROPERTY DAMAGE, ELECTRIC SHOCK, BURNS

OR OTHER INJURY.

WARNING

SAVE THESE INSTRUCTIONS

Page 1

166

(166IO) AP622 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 09/18/2017

INSTRUCTIONS

General

• Pump must be charged before use and is not designed for inflation directly from household AC power sources.

• It is recommended that the first charge to be 10 hours or overnight using the AC adapter powered by

household 220-240 AC voltage.

• If necessary, the initial charge can be made using the DC power Cord plugged into an automobile cigarette

lighter or 12V DC accessory receptacle for one hour. After the first charge, it may be used for inflation (without

cords) and recharged using either the AC Adapter or Fast-charged (1 hour only) using the 12 Volt DC Power

Cord. See specific instructions below.

• The external flexible cable or cord of this transformer cannot be replaced. If the cord is damaged, the

transformer shall be scrapped.

• The "O" position turns the pump OFF and is also the RECHARGE mode position.

• The batteries are permanently sealed in the pump and cannot be removed or replaced. As the pump weakens

from use, recharge the batteries. Do not wait until they are fully discharged.

• Do not dispose of airpump and its batteries in a fire. Check your local regulations for proper disposal

instructions.

• The battery must be removed from the appliance before it is scrapped.

• The appliance must be disconnected from the supply mains when removing the battery.

• The battery is to be disposed of safely.

• Keep away from heat or direct sunlight.

•Return pump, DC power cord, AC adapter and nozzles to package when not in use.

• No specific air pump maintenance is required.

CHARGE/RECHARGE INSTRUCTIONS

Charging the pump by AC adapter using household 220-240 AC voltage:

1. The pump must be charged for 10 hours or overnight with AC adapter powered by household 220-240 AC

voltage.

2. Plug the AC adapter power cord into the air pump power receptacle (FIG. 1).

3. Plug the other end of the AC adapter power cord into a household 220-240 Volt AC electrical outlet (FIG. 2).

4. Press the air pump switch to the "O" position to charge/recharge the batteries (FIG. 3).

5. Initial Charge: Charge the pump for ten (10) hours or overnight with household AC voltage.

6. When the pump is fully charged, remove the power cord (FIG. 4).

PARTS DESCRIPTION:

1. PUMP

2. INFLATION CONNECTOR

3. DEFLATION CONNECTOR

4. SWITCH

5. DETACHABLE 12V DC

POWER CORD

6. AC ADAPTER

7. NOZZLES

8. SWITCH OPERATION DETAIL

9. VENT HOLES / SLOTS

NAMES OF PARTS

Inflate and deflate

with batteries.

Inflate and deflate

with DC power.

Inflation OFF and recharge mode ON with AC or DC power.

220~240V 110~120V

FIG (2) FIG (3)

√

FIG (1) FIG (4)

INSTRUCTIONS

Charging the pump using a standard automobile 12 Volt DC power source:

1. The pump must be charged for 1 hour with 12 Volt DC power source.

2. Plug the 12 Volt DC power cord into the air pump power receptacle (FIG. 5).

3. Attach the DC power cord plug into a standard 12 Volt DC automobile

cigarette lighter or 12V DC accessory outlet (FIG. 5).

4. Press the air pump switch to the "O" position to charge/recharge the

batteries

(FIG. 3).

5. Charge: Charge the pump for 1 hour with 12 Volt DC power source.

6. When the pump is charged, immediately remove the power cord.

FIG (5)

SAVE THESE INSTRUCTIONS

Page 2

166

(166IO) AP622 ELECTRIC PUMP ENGLISH 4.875” X 7.25” 09/18/2017

INFLATION

When inflating large items such as inflatable boats and large air

mattresses, no accessory nozzle (FIG. 6) may be needed. The air

pumps inflation connector may fit directly into the inflation valve. If a

nozzle is needed, use the air pump nozzle most appropriately sized

for the product, then follow the instructions below:

Inflation using the 12 Volt DC power cord:

1. Plug the 12 Volt DC power cord into the air pump power receptacle (FIG. 5).

2. Attach the DC power cord plug into a standard 12 Volt DC automobile

cigarette lighter or accessory outlet (FIG. 5).

3. Attach the air pump inflation connector with nozzle if appropriate to the inflation valve on the item to be

inflated

(FIG. 7).

4. Depress "I" on the air pump switch to operate air pump (FIG. 8). Inflate item to desired level.

5. When the item is inflated, depress "O" to turn air pump off inflate mode (FIG. 3). Immediately unplug air

pump and cords when air pump is not in use.

FIG (6)

FIG (8)

Inflation using the air pump when fully charged (without power cord):

1. Attach the air pump inflation connector with nozzle if appropriate to the

inflation valve on the item to be inflated.

2. Depress "II" on the air pump switch to operate air pump (FIG. 9). Inflate

item to desired level.

3. After the item is inflated, depress "O" on the air pump switch.

DEFLATION

Deflation using the 12 Volt DC power cord:

1. Follow steps 1 & 2 under DC power inflation instructions.

2. Attach the air pump deflation connector with nozzle if

appropriate to the deflation valve on the item to be

deflated

(FIG. 10).

3. Depress "I" on the air pump switch to operate air pump.

Deflate item to desired level.

4. When the item is deflated, depress "O" to turn air pump off

deflate mode. Immediately unplug air pump and remove the

cord when air pump is not in use.

Deflation using the air pump when fully charged (without power cord):

1. Attach the air pump deflation connector with nozzle if appropriate into the deflation valve on the item to be

deflated.

2. Depress "II" on the air pump switch to operate air pump. Deflate item to desired level.

3. After the item is deflated, depress "O" on the air pump switch.

FIG (9)

FIG (7)

FIG (10)

SAVE THESE INSTRUCTIONS

Page 3

®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous licence de/Marcas registradas

utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex

Trading Ltd., Intex Development Co. Ltd., G.P.O Box 28829, Hong Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in

the European Union by/Distribué dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading B.V.,

Venneveld 9, 4705 RR Roosendaal – The Netherlands

www.intexcorp.com

�

Table of contents

Other Intex Water Pump manuals