Invacare 1110266 Instruction manual

Part No. 1114831 1Bolt-In-Place/SpringButton
Front Rigging Kit
Bolt-In-Place/Spring Button Front Rigging Kit
AssemblyandInstallationInstructions
Kits No. 1110266 and 1121271
SAVE THESE INSTRUCTIONS
NOTE: Check ALL parts for shipping damage. In case of shipping damage, DO NOT use. Contact
Carrier/Dealer for further instruction.
SAFETY SUMMARY
ToensurethesafeinstallationoftheBolt-In-Place/SpringButtonFrontRigging
Kit,these instructionsMUST be followed:
WARNING
DONOTinstall orusethisequipmentwithout firstreadingandunderstanding
theseinstructionsandtheOwner’sManualsupplied withthewheelchair. Ifyou
areunableto understandtheWarnings, CautionsorInstructions,contacta
healthcareprofessional,dealer ortechnical personnelbeforeattempting to
installthisequipment-otherwise,injuryordamagemayoccur.
INSTALLATION WARNING
AfterANYadjustments,repairorserviceandbeforeuse,makesureallattaching
hardwareistightenedsecurely-otherwiseinjuryordamagemayoccur.
Bolt-In-Place Front Rigging Kit 1110266 contains the following items:
DESCRIPTION QUANTITY
Riv Nut 2
ButtonHeadScrew 2
1/8-inch Hex key 1
Spring Buton Front Rigging kit 1112127 contains the following items:
DESCRIPTION QUANTITY
Spring buttons 4
INSTALLING THE BOLT-IN-PLACE FOOTPLATE KIT
(FIGURE 1)
NOTE:Thiskit mounts thefootplateassembly to thefrontrigging support sothattools are required
to remove or adjust the footrest assembly.
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner’s
manual shipped with wheelchair.
2. Pull up on the cam lock lever to unlock the cam.
NOTE:The elevating legrest has two (2) setsof release buttons, one (1) set abovethe other. Each
set will be visible one at a time allowing finer footplate height adjustment.
3. Push IN and hold the release button as shown in DETAIL “A” of FIGURE 1.
4. Rotate the lower footplate assembly 1/4 turn.

Bolt-In-Place/SpringButton 2Part No. 1114831
Front Rigging Kit
5. Remove the lower footplate assembly from the front rigging support.
6. Squeeze and push the release button down to remove from the footplate tube.
7. Ensure the cam lock lever is UP and unlocked.
8. Insert the footplate tube into the front rigging support.
9. Position the lower footplate assembly to the desired height.
10. Align the adjustment holes in the front rigging support and footplate assembly.
11. From the outside of the swingaway front rigging, insert the riv nut through both the
front rigging support and the footplate assembly.
12. From the inside of the swingaway front rigging, insert the button head screw through
the appropriate adjustment hole and thread into the riv nut.
13. Using a screwdriver to hold the riv nut in position, securely tighten the button head
screw. Torque to 32 in-lbs.
14. Push the cam lock lever DOWN to the locked position.
15. Reinstall the swingaway front rigging assembly. Refer to the owner’s manual that shipped
with wheelchair.
16. Repeat this procedure for the other footplate, if necessary.
FIGURE 1 - INSTALLING THE BOLT-IN-PLACE FRONT RIGGING KIT
OUTSIDE OF
SWINGAWAY
FRONT
RIGGING
INSIDE OF
SWINGAWAY
FRONT
RIGGING NOTE:Swingaway footrests shown.
Footplate Assembly
Front Rigging
Support
Cam Lock Lever
Riv Nut
Button Head Screw
Footplate Assembly
Front Rigging Support
Adjustment Hole
NOTE: Swingaway footrest shown.
Front Rigging
Support
Footplate
Assembly
Cam Lock Lever
Release
Button
Adjustment
Holes
DETAIL "A"

Part No. 1114831 3Bolt-In-Place/SpringButton
Front Rigging Kit
BOLT-IN-PLACE HEIGHT ADJUSTMENT (FIGURE 1)
NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest.
1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE
FRONT RIGGINGS in the owner’s manual shipped with wheelchair.
NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure.
2. Pull the cam lock lever UP to UNLOCKED position.
3. Using a screw driver to hold the riv nut in position, remove the button head screw
from the riv nut.
4. Remove the riv nut and button head screw securing the footplate assembly to the
front rigging support.
5. Adjust the footplate assembly height by aligning the desired adjustment holes in the
upper front rigging support and footplate assembly.
6. From the outside of the swingaway front rigging, insert the riv nut through both the
front rigging support and the footplate assembly.
7. From the inside of the swingaway front rigging, insert the button head screw through
the appropriate adjustment hole and thread into the riv nut.
8. Using a screwdriver to hold the riv nut in position, securely tighten the button head
screw. Torque to 32 in-lbs.
9. Rotate cam lock lever DOWN to LOCKED position.
10. Repeat STEPS 1-9 to adjust the remaining footrest.
11. Reinstall the swingaway front rigging. Refer to INSTALLING/REMOVING THE
FRONT RIGGINGS in the owner’s manual shat shipped with wheelchair.

Bolt-In-Place/SpringButton 4Part No. 1114831
Front Rigging Kit
INSTALLING THE SPRING BUTTON FRONT RIGGING
KIT (FIGURE 2)
NOTE: This kit allows tool-less removal or adjustment of the footplate assembly.
1. Remove the front rigging from the wheelchair. Refer to the wheelchair owner’s
manual shipped with wheelchair.
\
2. Pull the cam lock lever UP to UNLOCKED position.
3. Using a screw driver to hold the riv nut in position, remove the button head screw
from the riv nut as shown in DETAIL “A” of FIGURE 2.
4. Remove the riv nut and button head screw securing the footplate assembly to the
front rigging support.
5. Remove the footplate assembly from the upper front rigging support.
6. Perform one of the following as shown in DETAIL “B” OF FIGURE 2:
A. FOOTRESTS:
• With the spring pointing UP, insert the spring button into the footplate tube
so that the release buttons FULLY protrude through the top set of mounting
holes.
B. ELEVATING LEGRESTS AND FOOTRESTS WITH ADJUSTABLE ANGLE
FOOTPLATES:
• With the spring pointing DOWN, insert the bottom spring button into the
footplate tube so that the release buttons FULLY protrude through the
bottom set of mounting holes.
• With the spring pointing UP, insert the top spring button into the footplate
tube so that the release buttons FULLY protrude through the top set of
mounting holes.
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each
set will be visible one at a time allowing finer footplate height adjustment.
7. Insert the footplate tube into the front rigging support.
8. Push IN the release buttons and reposition the footplate assembly to the desired
height.
9. Ensure that the release buttons fully protrude from holes on both sides of the front
rigging support.
10. Rotate cam lock lever DOWN to LOCKED position.
11. Reinstall the swingaway front rigging assembly. Refer to the owner’s manual shipped
with wheelchair.
12. Ensure Release buttons are properly seated and FULLY protrude through the
adjustment holes before use.
13. Repeat this procedure for the other footplate, if necessary.

Part No. 1114831 5Bolt-In-Place/SpringButton
Front Rigging Kit
NOTE:Swingaway
footrests shown.
Footplate
Assembly
Front Rigging Support
Cam
Lock
Lever
Riv Nut
Button
Head
Screw
NOTE: Swingaway
footrest shown.
Front Rigging Support
Footplate
Assembly
Cam Lock
Lever
Release
Button
Adjustment
Holes
Release Buttons
Top Spring Button
Release Buttons
Spring Button
Bottom Spring Button
Spring
Spring
Spring
FIGURE 2 - INSTALLING THE SPRING BUTTON FOOTPLATE KIT
DETAIL “A” DETAIL “B”
ELEVATING LEGRESTS/
FOOTRESTS WITH
ADJUSTABLE ANGLE
FOOTPLATES
FOOTRESTS
SPRING BUTTON HEIGHT ADJUSTMENT (FIGURE 2)
NOTE: This procedure applies to the swingaway footrests and swingaway elevating legrest.
1. Remove the swingaway front rigging. Refer to INSTALLING/REMOVING THE
FRONT RIGGINGS in the owner’s manual shipped with wheelchair.
NOTE: Lay the front rigging assembly on a flat surface to simplify this procedure.
2. Pull the cam lock lever UP to UNLOCKED position.
NOTE: The elevating legrest has two (2) sets of release buttons, one (1) set above the other. Each
set will be visible one at a time allowing finer footplate height adjustment.
3. Push IN the release buttons and reposition the footplate assembly to the desired
height.
4. Ensure that the release buttons fully protrude from holes on both sides of the front
rigging support.
5. Rotate cam lock lever DOWN to LOCKED position.
6. Repeat this procedure for the other footplate, if necessary.
7. Reinstall the swingaway front rigging assembly. Refer to INSTALLING/REMOVING THE
FRONT RIGGING in the owner’s manual that shipped with wheelchair.
8. Ensure Release buttons are properly seated and FULLY protrude through the
adjustment holes before use.

Bolt-In-Place/SpringButton 6Part No. 1114831
Front Rigging Kit
NOTESNOTES
NOTESNOTES
NOTES

Part No. 1114831 7Bolt-In-Place/SpringButton
Front Rigging Kit
NOTESNOTES
NOTESNOTES
NOTES

Invacare Corporation www.invacare.com
USA
One Invacare Way Invacare is a registered trademark of
Elyria, Ohio USA Invacare Corporation.
44036-2125 Yes, you can. is a trademark of
800-333-6900 Invacare Corporation.
© 2003 Invacare Corporation
Part No. 1114831 Rev B - 07/03
MADE IN MEXICO