Invacare Infinity Back Support Manual

INFINITY BACK SUPPORTS
Assembly,Installationand
OperationInstructions

2
WARNING
THE PROCEDURES IN THIS MANUAL MUST BE PERFORMED
BY AN AUTHORIZED DEALER OR QUALIFIED SERVICE
TECHNICIAN.
DO NOT INSTALL OR USE THIS EQUIPMENT WITHOUT FIRST
READING AND UNDERSTANDING THIS MANUAL. IF YOU ARE
UNABLE TO UNDERSTAND THE WARNINGS, CAUTIONS, AND
INSTRUCTIONS, CONTACT A HEALTHCARE PROFESSIONAL,
DEALER OR TECHNICAL PERSONNEL IF APPLICABLE BEFORE
ATTEMPTING TO INSTALL OR USE THIS EQUIPMENT -
OTHERWISE INJURY OR DAMAGE MAY RESULT.
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE.
SAVE THESE INSTRUCTIONS
WARNING/CAUTION notices as used in this manual apply to hazards or unsafe practices
which could result in personal injury or property damage.
SPECIAL NOTES
SPECIAL NOTES ..............................................2
SAFETY SUMMARY..........................................3
IMPORTANT INFORMATION ........................... 5
INSTALLATION/ADJUSTMENT OVERVIEW ....5
PROCEDURE 1 - PREPARING
WHEELCHAIR ................................................6
INSTALLING/REMOVING CANE CLAMPS ........... 6
INSTALLING INSERTS ........................................ 6
PROCEDURE 2 - PREPARING THE INFINITY
BACK FOR INSTALLATION...........................7
INSTALLING/REMOVING THE
LATERAL SUPPORTS .................................... 7
INSTALLING/REMOVING CUSHIONS ................. 7
ADJUSTING THE MOUNTING HARDWARE ....... 9
TABLE OF CONTENTS
PROCEDURE 3 - INSTALLING/REMOVING
THE INFINITY BACK ................................ 10
INSTALLING/REMOVING THE INFINITY BACK .. 10
PROCEDURE 4 - ADJUSTING THE
INFINITY BACK......................................... 11
ADJUSTING CANE CLAMP HEIGHT ................. 11
ADJUSTING THE HINGE/ANGLE
(DUALFLEX ONLY) ..................................... 11
ADJUSTING THE DEPTH HARDWARE ........... 12
ADJUSTING THE LATERAL SUPPORTS ......... 12
PROCEDURE 5 - MAINTENANCE ................. 14
INSTALLING/REMOVING CUSHION FOAM ....... 14
INSPECTION.................................................... 15
CLEANING ....................................................... 15
LIMITED WARRANTY ................. BACK COVER
S
P
E
C
I
A
L
N
O
T
E
S
C
O
N
T
E
N
T
S
SPECIAL NOTES/TABLE OF CONTENTS

3
SAFETY SUMMARY
SAFETY SUMMARY
S
A
F
E
T
Y
S
U
M
M
A
R
Y
NOTE: Check all parts for shipping damage. In case of damage, DO NOT use. Contact your Dealer for further instruction.
INSTALLATION WARNINGS
Stabilize from the ground up. A stable base, pelvis and footrests are requirements for any
torso positioning system.
For proper installation of the Infinity Back and to reduce the risk of pressure sores, the
adjustment procedures in this manual MUST be performed in the following order:
1. Adjusting the Mounting Hardware
2. Adjusting the Hinge/Angle (DUALFLEX ONLY)
3. Adjusting the Depth Hardware
4. Adjusting the Lateral Supports
Ensure the Infinity Back is properly secured to the wheelchair BEFORE using. Upper
mounting pins must sit flush in the upper (swivel) cane clamps for the clamp lock to secure
the Infinity Back to the wheelchair. Lower mounting pins must rest in the groove on the
flange of the lower (fixed) cane clamps. Otherwise changes in seat depth will occur,
making the wheelchair less stable.
After ANY adjustments, repair or service and BEFORE use, make sure all attaching hard-
ware is tightened securely - otherwise injury or damage may occur.
STABILITY WARNINGS
The seat height, seat depth, back height, tilt angle, back angle, pivot point of seat frame,
seating system, caster position, size and position of the rear wheels, wheel locks, anti-tippers,
locking collar as well as the user condition directly relate to the stability of the wheelchair.
Any change to one (1) or any combination of the fourteen (14) may cause the wheelchair to
decrease in stability. Use EXTREME caution when using a new seating position.
Seat Height ●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Back Height ●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Seat Depth ●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Back Angle ✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Seating System ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Tilt Angle ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Seat Frame Pivot Point ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
CasterPosition ✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Rear Wheel Size ✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Rear Wheel Position ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
UserCondition ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓
Seat Dump ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●
Locking Collar ✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓✓✓
✓✓
✓●●
●●
●
Seat Height Back Height Seat Depth Back Angle Seating System Tilt Angle Seat Frame Pivot Point CasterPosition Rear Wheel Size Rear Wheel Position UserCondition Wheel Locks Anti-Tipppers Locking Collar Seat Dump
NOTE: When changes to the left hand column occur, follow across the chart and refer to the ✓ procedure
to maintain the proper stability, safety and handling of the wheelchair.
NOTE: Additional adjustments may be needed according to the wheelchair type. Refer to the wheelchair
owner's manual for these procedures.

4
SAFETY SUMMARY
STABILITY WARNINGS (CONTINUED)
ALWAYS make sure wheelchair is stable BEFORE reclining the back system. Rear wheels may
have to be repositioned rearward depending on the degree of recline. ALWAYS ensure
stability BEFORE using maximum amount of recline. TEST wheelchair BEFORE it is occupied by
end user to ensure stability.
To maintain the stability of the wheelchair when moving the rear wheels to ANY forward
position, the amount of recline MUST be limited to prevent the wheelchair from tipping
onto the anti-tippers.
The necessary back angle MUST be selected BEFORE repositioning rear wheels forward.
AS REGARDS RESTRAINTS - SEAT POSITIONING STRAPS - IT IS THE OBLIGATION OF THE DME
DEALER, THERAPISTS AND OTHER HEALTH CARE PROFESSIONALS TO DETERMINE IF A SEAT POSI-
TIONING STRAP IS REQUIRED TO ENSURE THE SAFE OPERATION OF THIS EQUIPMENT BY THE
USER. SERIOUS INJURY CAN OCCUR IN THE EVENT OF A FALL FROM A WHEELCHAIR.
SEATING PRESSURE WARNING
Skin condition should be checked very frequently after the installation and use of any new
seating system.
SAFETY SUMMARY
S
A
F
E
T
Y
S
U
M
M
A
R
Y

5
INSTALLATION/ADJUSTMENT OVERVIEW (FIGURE 1)
WARNING
For proper installation of the Infinity Back and to reduce the risk of pressure sores, the
adjustment procedures in this manual MUST be performed in the following order:
1. Adjusting the Mounting Hardware
2. Adjusting the Hinge/Angle (DUALFLEX ONLY)
I
N
F
O
R
M
A
T
I
O
N
IMPORTANT INFORMATION
The best way to avoid problems related to pressure sores
is to understand their causes and your role in a skin man-
agement program.
Your therapist and physician should be consulted if you
have any questions regarding weight relief, self-examina-
tion of skin, or individual limitations and needs.
All cushions should be selected carefully. Working with
your therapist, physician and equipment supplier is the
best way to assure that a cushion choice matches your
individual needs.
As the needs of the client become more complex, the
cushion evaluation becomes more important.
INSTALLATION/ADJUSTMENT OVERVIEW
STEP 1
Install the cane
clamps onto the
wheelchair. Refer
to INSTALLING/
REMOVING
CANE CLAMPS in
PROCEDURE 1
of this manual.
STEP 5
Install the Infinity Back
Refer to INSTALLING THE
INFINITY BACK in PROCE-
DURE 3 of this manual.
STEP 7
Adjust the depth of the Infinity
Back. Refer to ADJUSTING
THE DEPTH HARDWARE in
PROCEDURE 4 of this manual.
STEP 4
Adjust the mounting hardware.
Refer to ADJUSTING THE
MOUNTING HARDWARE in
PROCEDURE 2 of this manual.
STEP 6
Adjust the hinge/angle of the
Infinity Back. Refer to ADJUST-
ING THE HINGE/ANGLE
(DUALFLEX ONLY) in PRO-
CEDURE 4 of this manual.
FIGURE 1 - INSTALLATION/ADJUSTMENT OVERVIEW
O
V
E
R
V
I
E
W
IMPORTANT INFORMATION/INSTALLATION/ADJUSTMENT OVERVIEW
3. Adjusting the Depth Hardware
4. Adjusting the Lateral Supports
NOTE:
DualFlex
shown.
UniBack not
shown.
STEP 2
Install/remove the
lateral supports.
Refer to
INSTALLING/
REMOVING THE
LATERAL
SUPPORTS in
PROCEDURE 2
of this manual.
STEP 8
Adjust the lateral supports.
Refer to ADJUSTING
THE LATERAL SUP-
PORTS in PROCEDURE
4of this manual.
STEP 3
Install cushions. Refer to
INSTALLING/REMOVING
CUSHIONS in
PROCEDURE 2
of this manual.
Follow the steps below in order. Refer to the procedure below each step.

6
PROCEDURE 1 PREPARING WHEELCHAIR
P
R
E
P
A
R
I
N
G
W
H
E
E
L
C
H
A
I
R
This Procedure includes the following:
Installing/Removing Cane Clamps
InstallingInserts
INSTALLING/REMOVING CANE
CLAMPS (FIGURE 1)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGSin the SAFETY SUMMARYof this manual.
Installing Cane Clamps
WARNING
DO NOT modify cane clamps to fit 3/4-
inch tubing. Clamps provided are for 1-
inch or 7/8-inch tubing ONLY.
NOTE: The final positions of the upper (swivel) and lower
(fixed) cane clamps will be determined by the adjustments
made to the Infinity Back to fit the wheelchair and user.
1. Remove existing back upholstery. Refer to wheelchair
owner's manual.
2. Loosen, but do not remove the mounting screw on
the cane clamp with allen wrench provided.
3. Perform one (1) of the following:
UPPER (SWIVEL) CLAMPS - Visually inspect the
clamps to determine whether they are for the RIGHT
or LEFT back cane as shown in FIGURE 1.
NOTE: The upper (swivel) cane clamps are marked
with R for RIGHT and L for LEFT.
NOTE: RIGHT and LEFT are determined by sitting
in the wheelchair.
LOWER (FIXED) CLAMPS - Proceed to STEP 4.
4. Hold the Infinity Back up to the back canes of the wheel-
chair at the desired mounting height.
5. Visually inspect the location of the mounting pins on
the Infinity Back to determine the proper positions for
each cane clamp.
6. Position the clamp on the back cane at the desired
height so that the open end of the clamp is facing the
REAR of the back cane as shown in FIGURE 1.
7. Torque mounting screw to 45-50 in./lbs.
8. Perform one (1) of the following:
A. If cane clamp holds desired mounting position,
proceed to STEP 9.
B. If cane clamp DOES NOT hold desired mount-
ing position, clamp is too large - refer to INSTALL-
ING INSERTS in this procedure of the manual.
9. Repeat STEPS 2 - 8 for remaining cane clamp(s).
FIGURE 2 - INSTALLING INSERTS
Clamp
Half
Insert
FRONT OF
WHEELCHAIR
Back
Cane
Removing Cane Clamps
1. Remove the Infinity Back from the wheelchair. Refer
to REMOVING THE INFINITY BACK in PROCE-
DURE 3 of this manual.
2. Loosen, but do not remove the mounting screw on
the cane clamp.
3. Remove cane clamp from back cane.
Slide Clamp
OVER Insert
Insert
Clamp
SIDE VIEW
Back Cane
INSTALLING INSERTS (FIGURE 2)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETYSUMMARY of this manual.
NOTE: This procedure should be performed only if cane
clamps are too large for back cane tubing.
1. Loosen the mounting screw in the cane clamp.
NOTE: Mounting screw should be loosened enough to
create space for the insert to fit between the back cane
and the cane clamp.
2. Position one (1) insert onto the back cane near the cane
clampswiththeopeningfacingthefrontofthewheelchair.
3. Slide the cane clamp over the insert until the clamp
halves surround the insert as shown in FIGURE 2.
4. Torque mounting screw to 45-50 in./lbs.
NOTE: If clamps are still to large for back canes, DO
NOT use. Contact Invacare at the number on the back
page of this manual.
FIGURE 1 - INSTALLING/REMOVING
CANE CLAMPS
RIGHT
Upper
Cane
Clamp
LEFT
Upper
Cane
Clamp
Upper
(Swivel)
Cane
Clamp
Lower
(Fixed) Cane
Clamp
Mounting
Screw
WHEELCHAIR
FRONT
Back Cane
TOP VIEW
Open End
of Clamp
TOP VIEW
FRONT OF
WHEELCHAIR

7
This Procedure includes the following:
Installing/Removing the Lateral Supports
Installing/Removing Cushions
Adjusting the Mounting Hardware
PREPARING THE INFINITY BACK FOR INSTALLATION PROCEDURE 2
P
R
E
P
A
R
I
N
G
T
H
E
B
A
C
K
INSTALLING/REMOVING THE
LATERAL SUPPORTS (FIGURE 1)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
NOTE: The lateral supports include the lateral thoracic sup-
ports and the pelvic stabilizers.
Installing
1. Remove the back cushion from the back panel. Refer
to INSTALLING/REMOVINGCUSHIONSin this pro-
cedure of the manual.
2. Hold one (1) mounting screw with the threads UP.
3. Position the tooth lock washer on the mounting screw.
4. Position the curved washer on the mounting screw so
thatthe bent portion isTOWARDthe head ofthe mount-
ing screw as shown in FIGURE 1.
5. Position the lateral support in the upper, middle or lower
position,aligningthe mounting holes of thesupportwiththe
adjustment slot in the Infinity Back as shown in FIGURE1.
NOTE: The grooves next to the mounting holes in the lat-
eral supports are provided to align supports on either side
of the Infinity Back. Look through the toothed adjustment
slot to see which mounting hole has been used and use the
same mounting hole on the opposite lateral support.
6. Loosely install the mounting screw with washers
through the adjustment slot and into the mounting hole
on the lateral support.
NOTE: It is not necessary to tighten the mounting screws
on the lateral supports at this time. The lateral supports will
be adjusted after the Infinity Back has been installed on the
wheelchair and the user has been evaluated.
7. Repeat STEPS 2-6 for the other mounting screw for
this lateral support.
8. Repeat STEPS 2-7 for the remaining lateral supports.
9. Install the back cushion on the back panel. Refer to
INSTALLING/REMOVING CUSHIONS in this pro-
cedure of the manual.
Removing
1. Remove the back cushion from the back panel. Refer
to INSTALLING/REMOVINGCUSHIONSin this pro-
cedure of the manual.
2. Remove the (2) mounting screws and washers se-
curing the lateral support to the back panel.
FIGURE 1 - INSTALLING/REMOVING THE
LATERAL SUPPORTS
INSTALLING/REMOVING
CUSHIONS (FIGURE 2)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
CAUTION
The cushion covers are designed to pro-
tect the foam against moisture and to pro-
vide fire retardency. DO NOT use the back
without the covers. If the covers are torn,
they must be replaced immediately.
Installing/RemovingSpinal Insert
INSTALLING.
1. Remove the back cushion from the back panel(s).
Refer to INSTALLING/REMOVING BACK CUSH-
ION in this procedure of the manual.
2. Align the hook and loop fasteners on the spinal insert(s)
and back panel(s).
3. Press the rounded edge of the spinal insert(s) onto the
rounded groove in the back panel(s) to secure.
4. Install the cushion onto the back panel(s). Refer to IN-
STALLING/REMOVING BACK CUSHION in this
procedure of the manual.
Lateral Thoracic Support
Pelvic Stabilizer
Mounting
Screw
Tooth Lock Washer
Curved Washer
Toothed Adjustment
Slot
Back
Panel
Back Panel
Grooves
Grooves
3. Remove the lateral support.
4. Repeat STEPS2-3for the remaining lateral supports,
if necessary.
5. Install the back cushion on the back panel. Refer to
INSTALLING/REMOVING CUSHIONS in this pro-
cedure of the manual.

8
PREPARING THE INFINITY BACK FOR INSTALLATION
Top Flap
Bottom
Flap
Fastening Strips
(Attach to Back Panel)
Infinity
Back
Fastening
Strips
Elastic
Strip
REMOVING.
1. Remove the back cushion from the back panel(s).
Refer to INSTALLING/REMOVING BACK CUSH-
ION in this procedure of the manual.
2. Grasp the spinal insert(s) and pull to release the hook
and loop fasteners.
3. Install the cushion onto the back panel(s). Refer to
INSTALLING/REMOVINGBACK CUSHION in this
procedure of the manual.
Installing/Removing Lateral Support
Cushions
INSTALLING.
1. Hold the fastening end of the cushion away from the
fastening strip on the support.
2. Insert the support into the pocket on the opposite end
of the cushion as shown in FIGURE 2.
3. Release the fastening end of the cushion.
4. Press the fastening end firmly against the support to
secure.
REMOVING.
1. Grasp the fastening end of the cushion.
2. Pull upwards to release the hook and loop fasteners
as shown in FIGURE 2.
3. Slide the cushion off the support.
Installing/Removing Back Cushion
INSTALLING.
1. Lift the top flap up and pull the bottom flap down on
the back cushion cover.
2. Position the cushion against the back panel(s) with
the flaps on the outside of the Infinity Back.
NOTE: Ensure the lateral supports are positioned between
the back cushion foam and the elastic strips on either
side of the back cushion cover as shown in FIGURE 2.
3. If desired, install the adjustable positioning pad
(UniBack only) onto the back cushion foam. Refer to
INSTALLING/REMOVING CUSHION FOAM in
PROCEDURE 5 of this manual.
4. Close the top and bottom flaps of the back cushion cover
and press the fastening strips together to secure the back
cushion to the Infinity Back as shown in FIGURE2.
REMOVING.
1. Grasp the top flap and pull up to release the fastening
strips.
2. Grasp the bottom flap and pull down to release the
fastening strips.
3. Grasp the cushion and pull away from the Infinity
Back to remove.
BACK CUSHION
FIGURE 2 - INSTALLING/REMOVING CUSHIONS
PROCEDURE 2
P
R
E
P
A
R
I
N
G
T
H
E
B
A
C
K
Lateral Pad
Support
NOTE: Lat-
eral support
not installed
for clarity.
Hook and Loop
Fastening Strips
Pocket
FASTENING
END
POCKET
END
LATERAL SUPPORT
SPINAL INSERT
Spinal
Inserts
Fastening
Strips
Rounded Groove
in Back Panel Rounded Edge
Back Cushion
Top
Flap
Bottom
Flap
Lateral
Support

9
PREPARING THE INFINITY BACK FOR INSTALLATION
4. If necessary, loosen, but do not remove the two (2)
mounting screws securing each upper width bracket
to the back frame.
5. Slide the upper width brackets IN or OUT until the
mounting pins fit flush into both upper (swivel) cane
clamps and the depth hardware touches the cane
clamps as shown in FIGURE 3.
6. Install the Infinity Back onto the wheelchair. Refer
to INSTALLING/REMOVING THE INFINITY
BACK in PROCEDURE 3 of this manual.
7. Torque the two (2) mounting screws on each of the
four (4) width brackets to 45-50 in./lbs. to secure them
at the appropriate adjustment point.
UPPER (SWIVEL)
CANE CLAMP
Mounting
Pin
Back
Cane
LOWER (FIXED)
CANE CLAMP
Mounting Pin
Mounting
Screws
FIGURE 3 - ADJUSTING THE WIDTH
HARDWARE
UPPER
Mounting
Holes
LOWER
Width
Bracket
LOWER
Mounting
Holes
SLIDE
Width
Bracket IN
or OUT UPPER
Width
Bracket
Mounting Pin
Mounting Screws
NOTE:
Lower
mounting
pin not
shown for
clarity.
P
R
E
P
A
R
I
N
G
T
H
E
B
A
C
K
PROCEDURE 2
Depth
Hardware
Depth
Hardware
ADJUSTING THE MOUNTING
HARDWARE (FIGURE 3)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARYof this manual.
1. Hold the Infinity Back up to the back canes at the ap-
proximate installation height.
2. Visually inspect each side of the Infinity Back to see if the
width hardware is set at the appropriate height to match
the clamp installation and/or the back cane configuration.
3. Perform one (1) of the following:
CORRECT HEIGHT - Adjust the width of the
width hardware. Refer to ADJUSTING THE
MOUNTING HARDWARE WIDTH in this pro-
cedure of the manual.
INCORRECT HEIGHT - Adjust the height of the
width hardware. Refer to ADJUSTING THE
MOUNTING HARDWARE HEIGHT in this pro-
cedure of the manual.
Adjusting the Mounting Hardware Height
1. Remove the two (2) mounting screws from the width
bracket.
2. Align the opening in the width bracket with either the
UPPER or LOWER set of mounting holes.
3. Loosely install the two (2) mounting screws into the
desired set of mounting holes as shown in FIGURE3.
4. Adjust the width of the Infinity Back. Refer to ADJUST-
ING THE MOUNTING HARDWARE WIDTH in this
procedure of the manual.
Adjusting the Mounting Hardware Width
1. Hold the Infinity Back up to the back canes at the ap-
proximate installation height.
CAUTION
There should be a gap no larger than
1/16-inch between the depth hardware
and the cane clamps, otherwise damage
to the Infinity Back may occur. (FIGURE 3)
2. Visually inspect each side of the Infinity Back to see if
the depth hardware touches the cane clamps on both
back canes as shown in FIGURE 3.
3. Perform one (1) of the following:
CORRECT WIDTH - Proceed to STEP 6.
INCORRECT WIDTH - Proceed to STEP 4.
Depth
Hardware

10
INSTALLING/REMOVING THE INFINITY BACK
INSTALLING/REMOVING THE
INFINITY BACK (FIGURE 1)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
Installing the Infinity Back
1. Ensure the four (4) cane clamps are securely installed on
the wheelchair frame. Refer to INSTALLING/REMOV-
INGCANECLAMPSin PROCEDURE1ofthismanual.
2. Ifnecessary,adjustthemounting hardware tofittheback
canes. Refer to ADJUSTING THE MOUNTING
HARDWARE in PROCEDURE 2 of this manual.
3. Position the lower mounting pins between the lower
(fixed) cane clamp flanges and the back canes. The
mounting pins should be aligned with the groove in
the flange as shown in FIGURE 1.
4. Ensure the upper mounting pins are positioned on
top of the upper (swivel) cane clamps.
5. Twist the clamp locks on the upper (swivel) cane
clamps to the open position shown in FIGURE 1.
NOTE: Opening the clamp locks will cause the mounting
pins to slide down into the upper (swivel) cane clamps.
6. Ensure the clamps locks on the upper (swivel)
cane clamps are in the closed position shown in
FIGURE 1. If necessary, close the clamp locks.
NOTE: It may be necessary to adjust the cane clamp
height. Refer to ADJUSTING CANE CLAMP
HEIGHT in PROCEDURE 4 of this manual.
7. Ensure all cushions and lateral supports have been in-
stalled. Refer to PROCEDURE 2 - PREPARING THE
INFINITYBACKFORINSTALLATIONin this manual.
8. Position the user into the wheelchair to determine which
adjustments need to be made to properly fit the Infinity
Back. Refer to the wheelchair owner's manual.
9. Removethe user fromthewheelchair.Refertothe wheel-
chair owner's manual.
10. Perform the following procedures to adjust the Infin-
ity Back to fit the wheelchair and the user if neces-
sary. Refer to PROCEDURE 4 - ADJUSTING THE
INFINITY BACK in this manual.
A. ADJUSTING THE HINGE/ANGLE (DUALFLEX
ONLY)
B. ADJUSTING THE DEPTH HARDWARE
C. ADJUSTING THE LATERAL SUPPORTS
NOTE: Perform the above procedures in the order listed.
11. Inspect all mounting screws to ensure ALL hardware
has been tightened securely. Torque to 45-50 in./lbs.
12. Position the user in the wheelchair. Refer to the wheel-
chair owner's manual.
13. Visually inspect the user, the back and the wheelchair to
ensure all adjustments have been properly made.
14. Ifnecessary, repeat STEPS9-13until the user is com-
fortable.
Removing the Infinity Back
NOTE: The wheelchair should be unoccupied for this pro-
cedure.
1. Twist the upper (swivel) cane clamp locks in the open
position to release the upper mounting pins (FIGURE1).
2. Liftthe Infinity Back upwardstoremove the lower mount-
ing pins from the lower (fixed) cane clamps.
This Procedure includes the following:
Installing/Removing the Infinity Back
PROCEDURE 3
I
N
S
T
A
L
L
I
N
G
/
R
E
M
O
V
I
N
G
FIGURE 1 - INSTALLING/REMOVING THE INFINITY BACK
Installed DualFlex
Infinity Back
(UNIBACK NOT
SHOWN)
Upper
(Swivel)
Cane
Clamp Mounting
Pin
Back
Cane
Clamp
Lock
UPPER
(SWIVEL)
CANE
CLAMP
Clamp Lock in
CLOSED
Position
Clamp Lock in
OPEN Position
TOP
VIEW
Lower (Fixed)
Cane Clamp
Mounting
Pin
Back
Cane
Flange
Groove

11
ADJUSTING THE INFINITY BACK PROCEDURE 4
ADJUSTING THE HINGE/ANGLE
(DUALFLEX ONLY)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGSin the SAFETYSUMMARYof this manual.
NOTE: The following procedures apply to the DualFlex
ONLY.If installing/adjusting a UniBack proceedto ADJUST-
INGTHELATERALPADSin this procedureof the manual.
NOTE: Both hinges should be adjusted to have fixed
angles OR both hinges should be adjusted to have Dy-
namic Flex angles.
Adjusting the Angle (FIGURE 2)
1. Loosen the adjustment screws on both hinges.
2. Grasp and hold the top of the upper back panel and
bottom of the lower back panel.
3. Push or pull to adjust the angle of the back to the
desired angle.
4. Torque the adjustment screws on both hinges to 45-
50 in./lbs.
5. Install the Infinity Back onto the wheelchair. Refer
to INSTALLING/REMOVING THE INFINITY
BACK in PROCEDURE 3 of the manual.
6. Adjust the lateral supports. Refer to ADJUSTING THE
LATERALSUPPORTSin this procedure of the manual.
UPPER
Back Panel
LOWER
Back Panel
Hinge
Adjustment
Screw
FIGURE 2 - ADJUSTING THE HINGE
(DUALFLEX ONLY) - ADJUSTING THE ANGLE
WARNING
For proper installation of the Infinity Back
and to reduce the risk of pressure sores,
the adjustment procedures below MUST be
performed in the following order:
1. Adjusting the Mounting Hardware
2. Adjusting the Hinge/Angle
(DUALFLEX ONLY)
3. Adjusting the Depth Hardware
4. Adjusting the Lateral Pads
NOTE: To simplify the adjustment procedures, remove
the back from the wheelchair. Refer to INSTALLING/
REMOVING THE INFINITY BACK in PROCEDURE 3
of this manual.
NOTE: After performing each procedure, reinstall the back,
place the user in the wheelchair and inspect to ensure the
correct adjustments have been made for user comfort. If nec-
essary, repeat the procedure until the user is comfortable.
ADJUSTING CANE CLAMP HEIGHT
(FIGURE 1)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETY SUMMARY of this manual.
1. Loosen the mounting screw on the cane clamp.
2. Slide the cane clamp and if necessary, the insert inside
the cane clamp, up or down to the desired position.
3. Torque the mounting screw to 45-50 in./lbs.
4. Repeat STEPS 1-3 for the remaining clamps, if
necessary.
This Procedure includes the following:
Adjusting Cane Clamp Height
Adjusting the Hinge/Angle (DualFlex ONLY)
Adjusting the Depth Hardware
Adjusting the Lateral Supports
Back Cane
Mounting Screw
Upper (Swivel)
Cane Clamp
Lower (Fixed)
Cane Clamp
Mounting Screw
Adjust Cane
Clamps UP
or DOWN
FIGURE 1 - ADJUSTING CANE CLAMP
HEIGHT
A
D
J
U
S
T
I
N
G
Converting Dynamic Flex Hinges to Fixed
Angle Hinges (FIGURE 3)
1. Remove the four (4) long mounting screws securing
the hinge to the back panels.
2. Remove the elastomers, spacers and washers.
NOTE: Save the long mounting screws, elastomers, spac-
ers and washers for future conversion to Dynamic Flex.
3. Position the hinge on the back, aligning the hinge
mounting holes with the back panel mounting holes
as shown in FIGURE 3.
4. Install the four (4) short mounting screws. Torque to 45-
50 in./lbs.
5. Repeat STEPS 1-4 for opposite hinge.
6. Adjust the angle of the hinge. Refer to ADJUSTING
THE ANGLE in this procedure of the manual.
7. Adjust the lateral supports. Refer to ADJUSTING THE
LATERALSUPPORTSin this procedure of the manual.

12
ADJUSTING THE INFINITY BACKPROCEDURE 4
A
D
J
U
S
T
I
N
G
Converting Fixed Angle Hinges to Dynamic
Flex Hinges (FIGURE 3)
1. Remove the four (4) short mounting screws securing the
hinge to the back panels.
NOTE: Save the short mounting screws for future conversion
to fixed angle hinges.
2. Position the elastomers, spacers and washers as shown
in FIGURE 3.
NOTE: Ensure all mounting holes are aligned.
3. Alignthehingewiththemountingholesoneachbackpanel.
4. Install the four (4) long mounting screws. Torque to 45-50
in./lbs.
5. Adjust the lateral supports. Refer to ADJUSTING THE
LATERALSUPPORTSin this procedure of the manual.
Elastomer
Spacer
Washer
Mounting Screws
Hinge
FIGURE 3 - ADJUSTING THE HINGE
(DUALFLEX ONLY) - CONVERTING HINGES
Back
Panel
Mounting
Holes
Hinge Mounting
Hole
ADJUSTING THE DEPTH
HARDWARE (FIGURE 4)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGSin the SAFETY SUMMARYof this manual.
1. Ensure all cushions have been installed on the Infinity
Back.Refer to INSTALLING/REMOVINGCUSHIONS
in PROCEDURE 2 of this manual.
2. Hold the Infinity Back up to the wheelchair.
3. Visually inspect the Infinity Back and the wheelchair
to determine the desired depth.
4. Loosen the mounting screw in the depth bracket.
5. Slide the depth bracket until the mounting screw is
positioned in the desired adjustment hole.
NOTE: The width bracket has two (2) mounting holes. It
may be necessary to move the mounting screw to the
other hole to achieve the desired depth.
6. Torque mounting screw to 45-50 in./lbs. tosecuredepth
bracket to width bracket.
7. Perform one (1) of the following:
DUALFLEX- Adjust the hinge and/or angle of the back,
if present. Refer to ADJUSTINGTHEHINGE/ANGLE
in this procedure of the manual.
UNIBACK- Proceed to ADJUSTINGTHELATERAL
SUPPORTS in this procedure of the manual.
ADJUSTING THE LATERAL
SUPPORTS (FIGURE 5)
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETYSUMMARY of this manual.
NOTE: Lateral supports include the lateral thoracic sup-
ports and the pelvic stabilizers.
Adjusting the Width
1. Visually inspect the orientation of one (1) curved
washer on one (1) lateral support.
2. Perform one (1) of the following:
A. Curved washer oriented as shown in DETAIL
"A"of FIGURE5- Perform the following steps:
a. Loosen, but do not remove the mounting
screw.
b. Proceed to STEP 3.
B. Curved washer oriented as shown in DETAIL
"B"of FIGURE5- Perform the following steps:
a. Hold the mounting screw with the threads
UP.
b. Position the tooth lock washer on the
mounting screw.
c. Position the curved washer on the mount-
ing screw so that the bent portion is TO-
WARD the head of the mounting screw
as shown in DETAIL "A" of FIGURE 5.
d. Loosely install the mounting screw with
washers through the adjustment slot and
into the lateral support.
3. Repeat STEPS 1-2 for the other mounting screw
on the same lateral support.
4. Repeat STEPS 1-3 for the remaining lateral sup-
ports which need adjustment.
5. Position the user in the wheelchair.
Depth
Bracket
Mounting Screw
Mounting Hole
Adjustment
Hole
Width
Bracket
FIGURE 4 - ADJUSTING THE DEPTH
HARDWARE

13
PROCEDURE 4ADJUSTING THE INFINITY BACK
A
D
J
U
S
T
I
N
G
6. Slide one (1) lateral support to the desired location.
7. Visually inspect the adjustment slot to find proper lo-
cation for the curved washer.
8. Remove one (1) mounting screw, tooth lock washer
and curved washer.
9. Hold the mounting screw with the threads UP.
10. Position the tooth lock washer on the mounting screw.
11. Position the curved washer on the mounting screw
so that the bent portion is toward the threaded end of
the mounting screw.
12. Install the mounting screw with washers through the
toothed adjustment slot and into the lateral support.
13. Torque the mounting screw to 45-50 in./lbs., ensur-
ing the curved washer is seated properly in the
toothed adjustment slot shown in FIGURE 5.
14. Repeat STEPS 8-13 for the remaining mounting
screw on the lateral support.
15. Repeat STEPS6-14for the remaining lateral supports.
AdjustingtheHeight
NOTE: Both sets of lateral supports can be adjusted to
three (3) different height positions.
1. Remove the two (2) mounting screws, tooth lock wash-
ers and curved washers securing the lateral support to
theInfinity Back.
2. Hold one (1) mounting screw with the threads UP.
3. Position the tooth lock washer on the mounting screw.
4. Position the curved washer on the mounting screw so
thatthe bent portion isTOWARDthe head ofthe mount-
ing screw as shown in DETAIL "A" of FIGURE 5.
5. Repeat STEPS2-4for the remaining mounting screw
and washers.
6. Position the lateral support in the upper, middle or lower
position, aligning the mounting holes of the support with
the adjustment slot in the Infinity Back as shown in DE-
TAIL "B" of FIGURE5.
NOTE: The grooves next to the mounting holes in the
lateral support are provided to align lateral supports on
either side of the Infinity Back. Look through the toothed
adjustment slot to see which mounting hole has been used
and use the corresponding mounting hole on the oppo-
site lateral support if desired.
7. Loosely install the two (2) mounting screws and washers
to secure the supports to the back as shown in DETAIL
"B" of FIGURE 5.
NOTE: The curved washer should be facing away from
the Infinity Back for ease of adjustment.
8. Adjustthewidthofthe lateral supports. RefertoADJUST-
ING THE WIDTH in this procedure of the manual.
Lateral Thoracic
Support
Hip
Guides
Mounting
Screws
Washers
LOOSEN
Mounting
Screws and
SLIDE Lateral
Pads
Toothed Adjustment Slot
FIGURE 5 - ADJUSTING THE LATERAL
SUPPORTS
UPPER
Back
Panel
LOWER
Back Panel
Lateral Thoracic Support
Hip Guide
Mounting
Screw
Washer
Curved Washer
Toothed Adjustment
Slot
Back
Panel
Back Panel
DETAIL "B"
Grooves
Grooves
Curved
Washer
Toothed Adjustment Slot
Tooth Lock Washer
Mounting
Screws
DETAIL "A"

14
PROCEDURE 5
FIGURE 1 - REMOVING/INSTALLING
BACK CUSHION FOAM
Top of
Back
Cover
Back
Cushion
Foam
Bottom
Flap
INSTALLING/REMOVING
CUSHION FOAM
NOTE: Refer to the INSTALLATION AND STABILITY
WARNINGS in the SAFETYSUMMARY of this manual.
Installing/Removing Back Cushion Foam
(FIGURE 1)
INSTALLING.
1. Remove the back cushion from the back panel(s).
Refer to INSTALLING/REMOVING CUSHIONS in
PROCEDURE 2 of this manual.
2. Position the back cushion on a flat surface.
3. Pull the top flap UP and the bottom flap DOWN.
4. Slide the top of the cushion foam inside the cushion
cover.
5. Ensure the bottom and sides of the cushion foam
are behind the elastic strips on either side of the
cushion cover.
6. Install the cushion onto the Infinity Back. Refer to IN-
STALLING/REMOVING CUSHIONS in PROCE-
DURE 2 of this manual.
REMOVING.
1. Remove the back cushion from the back panel(s).
Refer to INSTALLING/REMOVING CUSHIONS in
PROCEDURE 2 of this manual.
2. Pull the top flap UP and the bottom flap DOWN.
3. Grasp the cushion foam and remove it from the back
cover.
MAINTENANCE
M
A
I
N
T
E
N
A
N
C
E
This Procedure includes the following:
Installing/Removing Cushion Foam
Inspection
Cleaning
Top Flap
Top of Cushion
Foam
Elastic
Strip
Installing/Removing Lateral Support
Cushion Foam (FIGURE 2)
INSTALLING.
1. Remove the lateral support cushion from the lateral
support. Refer to INSTALLING/REMOVINGCUSH-
IONS in PROCEDURE 2 of this manual.
2. Position the cushion cover on a flat surface with the
pocket facing UP as shown in FIGURE 2.
3. Pull up and hold the upper flap.
4. Slide the larger end of the cushion foam into the open-
ing in the cushion cover.
5. Pull down and hold the lower flap.
6. Insert the tapered end of the cushion foam into the
cushion cover.
REMOVING.
1. Remove the lateral support cushion from the lateral
support. Refer to INSTALLING/REMOVINGCUSH-
IONS in PROCEDURE 2 of this manual.
2. Position the cushion cover as shown in FIGURE 2.
3. Pull up and hold the upper flap on the pocket side of
the cushion cover.
4. Pull down the lower flap.
5. Grasp the cushion foam and remove it from the cush-
ion cover.
Fastening Strip
(Attach to Lateral
Support)
Pocket (Insert
Lateral Support)
Lower Flap
Upper
Flap
Opening
(Insert
Cushion
Foam)
Tapered
End of
Cushion
Foam
Cushion
Cover
FIGURE 2 - REMOVING/INSTALLING
LATERAL SUPPORT CUSHION FOAM

15
PROCEDURE 5
M
A
I
N
T
E
N
A
N
C
E
MAINTENANCE
Installing/Removing Adjustable Positioning
Pad (UNIBACK ONLY) (FIGURE 3)
INSTALLING.
1. Lift the top flap up and pull the bottom flap down on the
back cushion cover.
2. Grasp the cushion and pull upwards to remove the
cushion from the back.
3. Align the fastening strips on the adjustable positioning
pad with the fastening strips on the back cushion foam
as shown in FIGURE 3.
4. Press the adjustable positioning pad firmly against
the back cushion foam to secure.
5. Install the back cushion onto the Infinity Back. Refer to
INSTALLING/REMOVINGCUSHIONSin PROCE-
DURE 2 of this manual.
NOTE: The adjustable positioning pad may be adjusted
to different heights according to the needs of the user.
It may be necessary to trim the adjustable positioning
pad to fit the wheelchair or the user.
NOTE: It may be necessary to place the user in the
wheelchair with the back cushion installed to determine
the final location of the adjustable positioning pad.
REMOVING.
1. Lift the top flap up and pull the bottom flap down on the
back cushion cover.
2. Grasp the cushion and pull upwards to remove the
cushion from the back.
3. Grasp the adjustable positioning pad and pull to re-
lease the fastening strips.
4. Install the back cushion onto the Infinity Back. Refer to
INSTALLING/REMOVINGCUSHIONSin PROCE-
DURE 2 of this manual.
Bottom Flap
Adjustable
Positioning
Pad
Fastening
Strips
Top Flap
Back
Cushion
Back
Cushion
Foam
FIGURE 3 - INSTALLING/REMVOING
ADJUSTABLE POSITIONING PAD
(UNIBACK ONLY)
INSPECTION
WARNING
DO NOT continue to use this product if
any of the following problems as de-
scribed are discovered. Corrective main-
tenance can be performed at or ar-
ranged through your equipment supplier.
1. Initially and once a week, visually inspect all parts,
including hardware, upholstery materials, foams (if
accessible), and plastics for deformation, corrosion,
breakage, wear and/or compression.
2. Check ALL fasteners weekly to ensure that mechani-
cal connections are secure.
WARNING
Skin condition should be checked very fre-
quently after the installation and use of any
new seating system.
CLEANING
Cover
1. Machine wash the covers once a week.
CAUTION
MACHINE WASH back cover and lateral
support covers in cold water on gentle
cycle using a mild detergent. DO NOT use
fabric softeners or bleach. DO NOT ma-
chine dry. Air dry ONLY. DO NOT dry in sun.
Foam
If the back cushion foam becomes contaminated because
of moisture, the back cushion should be replaced imme-
diately.

Form No. 99-104 Part No. 1077719 Rev. A. (1)-3/99 Printed in U.S.A.
INVACARE CORPORATION lONE INVACARE WAY lP.O. Box 4028 lElyria, Ohio 44036-2125
Phone [phone] lTechnical Support 1-800-832-4707
INVACARE CANADA l5970 Chedworth Way lMississauga, Ontario, L5R 3T9 lCanada
Phone [phone]
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW
APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal rights
which vary from state to state.
Invacare warrants its products to be free from defects in materials and workmanship for
use by the original purchaser for a period of two (2) years from the date of purchase on
the back and ninety (90) days from the date of purchase on the cover. If within such
warranty period any such product shall be proven to be defective, such product shall
be repaired or replaced, at Invacare's option. This warranty does not include any labor
or shipping charges incurred in replacement part installation or repair of any such prod-
uct. Invacare's sole obligation and your exclusive remedy under this warranty shall be
limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Invac-
are product. In the event you do not receive satisfactory warranty service, please write
directly to Invacare at the address at the bottom of this page. Provide dealer’s name,
address, date of purchase, indicate nature of the defect and, if the product is serialized,
indicate the serial number. Do not return products to our factory without our prior con-
sent.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY SHALL NOT APPLY TO SERIAL
NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED OR DEFACED, PROD-
UCTS SUBJECTED TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION, MAINTENANCE OR
STORAGE, COMMERCIAL OR INSTITUTIONAL USE, PRODUCTS MODIFIED WITHOUT INVACARE'S
EXPRESS WRITTEN CONSENT INCLUDING, BUT NOT LIMITED TO, MODIFICATION THROUGH
THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTS DAMAGED BY REASON OF
REPAIRS MADE TO ANY COMPONENT WITHOUT THE SPECIFIC CONSENT OF INVACARE, OR
TO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND INVACARE'S CONTROL, AND SUCH
EVALUATION WILL BE SOLELY DETERMINED BY INVACARE. THE WARRANTY SHALL NOT APPLY
TO PROBLEMS ARISING FROM NORMAL WEAR OR FAILURE TO ADHERE TO THESE INSTRUC-
TIONS.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS WARRAN-
TIES. IMPLIED WARRANTIES, IF ANY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL NOT EXTEND BEYOND THE DURA-
TION OF THE EXPRESSED WARRANTY PROVIDED HEREIN AND THE REMEDY FOR VIOLATIONS
OF ANY IMPLIED WARRANTY SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF THE DEFEC-
TIVE PRODUCT PURSUANT TO THE TERMS CONTAINED HEREIN. INVACARE SHALL NOT BE
LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES WHATSOEVER.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH STATE/PROVINCIAL LAWS AND RE-
QUIREMENTS.