Invacare P9000 XDT Installation and operation manual

Owner’s Operator and Maintenance Manual
DEALER: This manual MUST be given to
the user of the wheelchair.
USER: BEFORE using this wheelchair, read
this manual and save for future reference.
For more information regarding
Invacare products, parts, and services,
please visit www.invacare.com
P9000™XDT

P9000™XDT 2Part No. 1118386
 WARNING
A QUALIFIED TECHNICIAN MUST PERFORM THE INITIAL SET UP
OF THIS WHEELCHAIR. ALSO, A QUALIFIED TECHNICIAN MUST
PERFORM ALL PROCEDURES IN THE SERVICE MANUAL.
WHEELCHAIR USERS: DO NOT SERVICE OR OPERATE THIS
EQUIPMENT WITHOUT FIRST READING AND UNDERSTANDING
(1) THE OWNER’S OPERATOR AND MAINTENANCE MANUAL
AND (2) THE SEATING SYSTEM’S MANUAL (IF APPLICABLE). IF
YOU ARE UNABLE TO UNDERSTAND THE WARNINGS,
CAUTIONS, AND INSTRUCTIONS, CONTACT INVACARE
TECHNICAL SUPPORT BEFORE ATTEMPTING TO SERVICE OR
OPERATE THIS EQUIPMENT - OTHERWISE INJURY OR DAMAGE
MAY RESULT.
DEALERS AND QUALIFIED TECHNICIANS: DO NOT SERVICE OR
OPERATE THIS EQUIPMENT WITHOUT FIRST READING AND
UNDERSTANDING (1) THE OWNER’S OPERATOR AND
MAINTENANCE MANUAL, (2) THE SERVICE MANUAL (IF
APPLICABLE) AND (3) THE SEATING SYSTEM’S MANUAL (IF
APPLICABLE). IF YOU ARE UNABLE TO UNDERSTAND THE
WARNINGS, CAUTIONS AND INSTRUCTIONS, CONTACT
INVACARE TECHNICAL SUPPORT BEFORE ATTEMPTING TO
SERVICE OR OPERATE THIS EQUIPMENT - OTHERWISE, INJURY
OR DAMAGE MAY RESULT.
NOTE: Updated versions of this manual are available on www.invacare.com.

TABLE OF CONTENTS
Part No. 1118386 3P9000™XDT
TABLE OF CONTENTS
REGISTER YOUR PRODUCT ............................................................... 6
SPECIAL NOTES ................................................................................ 9
TYPICAL PRODUCT PARAMETERS .................................................. 10
LABEL LOCATIONS ......................................................................... 11
SECTION 1—GENERAL GUIDELINES ................................................. 12
Controller Settings/Repair or Service .................................................................................................12
Operating Information.............................................................................................................................12
Tire Pressure .............................................................................................................................................14
Electrical Accessories ..............................................................................................................................14
Batteries......................................................................................................................................................14
Charging Batteries ...............................................................................................................................15
Grounding Instructions ...........................................................................................................................15
Rain Test.....................................................................................................................................................16
Weight Training ........................................................................................................................................16
Weight Limitation.....................................................................................................................................16
SECTION 2—EMI INFORMATION ..................................................... 17
SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS ......................... 19
Stability and Balance.................................................................................................................................19
Coping With Everyday Obstacles.........................................................................................................19
A Note to Wheelchair Assistants ........................................................................................................20
Tipping.........................................................................................................................................................20
Tipping - Curbs.....................................................................................................................................20
Lifting/Stairways ........................................................................................................................................21
Transferring to and From Other Seats ...............................................................................................22
Percentage of Weight Distribution ......................................................................................................23
Reaching, Leaning and Bending - Forward ..........................................................................................23
Reaching and Bending - Backward ........................................................................................................24
SECTION 4—SAFETY INSPECTION/TROUBLESHOOTING .................... 25
Safety Inspection Checklists...................................................................................................................25
Inspect/Adjust Initially .........................................................................................................................25
Inspect/Adjust Weekly........................................................................................................................26
Inspect/Adjust Monthly.......................................................................................................................26
Inspect/Adjust Periodically.................................................................................................................26
Troubleshooting - Mechanical ...............................................................................................................27
Troubleshooting Guide ...........................................................................................................................27
Checking Battery Charge Level.............................................................................................................28

P9000™XDT 4Part No. 1118386
SECTION 5—WHEELCHAIR OPERATION ........................................... 29
SPJ™Joystick Switches and Indicators .................................................................................................29
Multi Function Charger Port .............................................................................................................29
On/Off Toggle Switch .........................................................................................................................29
Speed Control switch .........................................................................................................................29
Joystick....................................................................................................................................................29
Information Gauge Display ................................................................................................................30
Operating the Wheelchair......................................................................................................................32
Turning the Power On/Off ................................................................................................................32
Using the Horn.....................................................................................................................................32
Using the Joystick to Drive the Chair.............................................................................................32
SECTION 6—FRONT RIGGINGS ........................................................ 34
Installing/Removing/Using the Footrest/Legrest................................................................................34
Installing..................................................................................................................................................34
Removing ...............................................................................................................................................35
Using .......................................................................................................................................................35
Adjusting the Footrest Height...............................................................................................................35
Replacing the Heel Loop.........................................................................................................................36
Raising/Lowering the Legrest Assembly..............................................................................................36
SECTION 7—ARMS ......................................................................... 38
Adjusting Armrest Height.......................................................................................................................38
Swing-Back Arms......................................................................................................................................39
Replacing Armrest Pad............................................................................................................................39
SECTION 8—SEAT AND BACK ......................................................... 40
Replacing the Seat Upholstery...............................................................................................................40
Replacing the Back Upholstery..............................................................................................................41
Adjusting the Back Height ......................................................................................................................42
Replacing Seat Positioning Strap ...........................................................................................................43
SECTION 9—JOYSTICK .................................................................... 44
Preparing the Joystick for Use...............................................................................................................44
Repositioning the Joystick.......................................................................................................................45
SECTION 10—CASTER .................................................................... 46
Adjusting Forks .........................................................................................................................................46

Part No. 1118386 5P9000™XDT
SECTION 11—BATTERIES ................................................................ 47
When to Charge Batteries.....................................................................................................................47
Charging Batteries....................................................................................................................................48
Description and Use of Battery Chargers......................................................................................48
Connecting the Battery Charger......................................................................................................49
Replacing the Batteries............................................................................................................................49
Recommended Battery Types...........................................................................................................49
Cleaning Battery Terminals ...............................................................................................................50
Removing/Installing the Battery Boxes ................................................................................................50
Installing/Removing Battery Tray......................................................................................................51
Installing/Removing Batteries Into/From Battery Boxes.............................................................52
Connecting Battery Cables ....................................................................................................................53
Direct Mount Method.........................................................................................................................54
Battery Clamp Method .......................................................................................................................57
Replacing Battery Box Retaining Strap............................................................................................60
SECTION 12—CLUTCH/MOTOR LOCK ............................................... 61
Engaging/Disengaging the Clutches.......................................................................................................61
SECTION 13—WHEEL LOCKS ............................................................ 62
Installing/Adjusting/Using the Wheel Locks .......................................................................................62
Installing/Adjusting ...............................................................................................................................62
Using .......................................................................................................................................................63
SECTION 14—ANTI-TIPPERS ........................................................... 64
Installing/Removing/Adjusting Anti-Tippers........................................................................................64
Installing..................................................................................................................................................64
Removing ...............................................................................................................................................64
Adjusting Height...................................................................................................................................64
TRANSPORTING ............................................................................ 66
Transporting the P9000 XDT................................................................................................................66
Unfolding/Folding the Wheelchair ...................................................................................................66
Unfolding ..........................................................................................................................................66
Folding ...............................................................................................................................................66
LIMITED WARRANTY ..................................................................... 68

REGISTER YOUR PRODUCT
P9000™XDT 6Part No. 1118386
REGISTER YOUR PRODUCT
The benefits of registering:
1. Safeguard your investment.
2. Ensure long term maintenance and servicing of your purchase.
3. Receive updates with product information, maintenance tips, and industry news.
4. Invacare can contact you or your provider, if servicing is needed on your product.
5. It will enable Invacare to improve product designs based on your input and needs.
Register ONLINE at www.invacare.com
- or -
Complete and mail the form on the next page
Any registration information you submit will be used by Invacare Corporation only, and
protected as required by applicable laws and regulations.

Name _______________________________________________________________
Address _____________________________________________________________
City ___________________ State/Province __________
Zip/Postal Code ________
Email ___________________________________ Phone No. _________________
Invacare Model No. ______________________ Serial No. __________________
Purchased From _________________________Date of Purchase:___________
1. Method of purchase: (check all that apply)
❏ Medicare ❏ Insurance ❏Medicaid ❏ Other __________________________
2. This product was purchased for use by: (check one)
❏ Self ❏ Parent ❏ Spouse ❏ Other
3. Product was purchased for use at:
❏ Home ❏ Facility ❏ Other
4. I purchased an Invacare product because:
❏ Price ❏ Features (list features) _________________________________________
5. Who referred you to Invacare products? (check all that apply)
❏Doctor ❏ Therapist ❏ Friend ❏Relative ❏Dealer/Provider ❏Other_________
❏ Advertisement (circle one): TV, Radio, Magazine, Newspaper ❏ No Referral_____
6. What additional features, if any, would you like to see on this product?
__________________________________________________________________________
7. Would you like information sent to you about Invacare products that may be available for a
particular medical condition? ❏Yes ❏No
If yes, please list any condition(s) here and we will send you information by email and/or mail about
any available Invacare products that may help treat, care for or manage such condition(s):
__________________________________________________________________________
8. Would you like to receive updated information via email or regular mail about the Invacare
home medical products sold by Invacare's dealers? ❏Yes ❏No
9. What would you like to see on the Invacare website?
__________________________________________________________________________
10. Would you like to be part of future online surveys for Invacare products? ❏ Yes ❏ No
11. User's Year of birth: ______________________________________________________
If at any time you wish not to receive future mailings from us, please contact us at Invacare Corporation,
CRM Department, 39400 Taylor Parkway, Elyria, OH 44035, or fax to 877-619-7996 and we will remove
you from our mailing list.
To find more information about our products, visit www.invacare.com.
PRODUCT REGISTRATION FORM
Register ONLINE at www.invacare.com - or -
Complete and mail this form
Cut Along Line
Fold
here
Fold
here

Fold
here
Fold
here
Cut Along Line
Invacare Product Registration Form
Please Seal with
Tape Before Mailing

SPECIAL NOTES
Part No. 1118386 9P9000™XDT
SPECIAL NOTES
WARNING/CAUTION notices as used in this manual apply to hazards or unsafe
practices which could result in personal injury or property damage.
NOTICE
THE INFORMATION CONTAINED IN THIS DOCUMENT IS SUBJECT TO
CHANGE WITHOUT NOTICE.
WHEELCHAIR USER
As a manufacturer of wheelchairs, Invacare endeavors to supply a wide variety of
wheelchairs to meet many needs of the end user. However, final selection of the
type of wheelchair to be used by an individual rests solely with the user and his/her
healthcare professional capable of making such a selection.
WHEELCHAIR TIE-DOWN RESTRAINTS AND SEAT RESTRAINTS
Wheelchair users should NOT be transported in vehicles of any kind while in
wheelchairs. As of this date, the Department of Transportation has not approved
any tie-down systems for transportation of a user while in a wheelchair, in a moving
vehicle of any type.
It is Invacare’s position that users of wheelchairs should be transferred into
appropriate seating in vehicles for transportation and use be made of the restraints
made available by the auto industry. Invacare cannot and does not recommend any
wheelchair transportation systems.
As regards to restraints - seat positioning straps - it is the obligation of the DME
dealer, therapists and other healthcare professionals to determine if a seating
positioning strap is required to ensure the safe operation of this equipment by the
user. Serious injury can occur in the event of a fall from a wheelchair.
 WARNING
Invacare products are specifically designed and manufactured for use in conjunction
with Invacare accessories. Accessories designed by other manufacturers have not
been tested by Invacare and are not recommended for use with Invacare products.
The seat positioning strap is a positioning belt only. It is not designed for use as a
safety device withstanding high stress loads such as auto or aircraft safety belts. If
signs of wear appear, belt MUST be replaced immediately.

TYPICAL PRODUCT PARAMETERS
P9000™XDT 10 Part No. 1118386
TYPICAL PRODUCT PARAMETERS
*NOTE: Range will vary with battery conditions, surface, terrain and operating weight.
**NOTE: Includes seating system and accessories.
P9000 XDT
SEAT WIDTH 18 inches
SEAT DEPTH 16 or 18-inches (by extension)
BACK HEIGHT 17, 18, or 19 inches
SEAT-TO-FLOOR 19½ inches
OVERALL WIDTH
(EXCLUDING JOYSTICK)
Unfolded - 24½ inches
Folded - 13 inches
OVERALL HEIGHT 38 inches (with 17 inch back)
OVERALL LENGTH 28 inches (base only) to 47 inches (with riggings and anti-tippers)
WEIGHT
W/O BATTERIES AND FRONT RIGGINGS
WITH UI BATTERIES
SHIPPING
82 lbs
142 lbs
100 lbs
DRIVE WHEELS/TIRES (FLAT FREE) 12½ inches x 2¼ inches
CASTERS W/PRECISION SEALED
BEARINGS 8 x 1¾ inches semi-pneumatic
ANTI-TIPPERS Removable
FOOTRESTS/
LEGRESTS Swingaway, Removable
ARMRESTS Adjustable Height - Desk
UPHOLSTERY Black Nylon
BATTERIES
BATTERY/SIZE (NOT SUPPLIED)
TWO (2) REQUIRED U1
SPEED (M.P.H.) 0 to 4
TURNING RADIUS
CHAIR ONLY
CHAIR WITH FOOTREST
CHAIR WITH ANTI-TIPPERS
Front - 26 inches; Rear - 13 inches
36 inches
16 inches
*RANGE (VARIABLE) 12-14 miles with U1 batteries
**WEIGHT LIMITATION 250 lbs

LABEL LOCATIONS
Part No. 1118386 11 P9000™XDT
LABEL LOCATIONS
Crossmember
Lower Frame
Tube
WARNING
DO NOT OPERATE WITHOUT
THE ANTI-TIP TUBES
INSTALLED.
REV. 5/98 P/N 60106X144
Refer to Owner's Manual
for proper anti-tipper
setting.
1085379
WARNING
IMPORTANT NOTICE
T he wheel locks on this wheelchair have been
pre-set at the factory to comply with the
V eterans Administration functional S tandard
8320.01 of the Federal Register , paragraph
3.2.4.5.3. If these wheel locks do not meet
your needs, follow instructions below .
! CAUTION
Any w heel lock adjustments should embed
wheel lock shoe at least 1/8" into tire when
locked (3/16" on pneumatic tires).
INSTRUCTIONS FOR WHEEL
LOCK ADJUSTMENTS
1. Loosen wheel lock mounting fastener,
which runs through mounting bracket and
frame.
2. Slide clamp toward rear wheel until wheel
lock shoe is embedded into tire material at
least 1/8" when handle is engaged to the
lock position (3/16" for pneumatic tires).
3. Tighten mounting fastener to secure
mounting bracket in desired location and
recheck lock sh o e embedding.
4. Inspect for correct locking action BEFORE
actual use.
00078X021-0394

SECTION 1—GENERAL GUIDELINES
P9000™XDT 12 Part No. 1118386
SECTION 1—GENERAL GUIDELINES
 WARNING
This section contains important information for the safe operation and use of this
product. DO NOT use this product or any available optional equipment without
first completely reading and understanding these instructions and any additional
instructional material such as Owner’s Manuals, Service Manuals or Instruction
Sheets supplied with this product or optional equipment. If you are unable to under-
stand the Warnings, Cautions or Instructions, contact a healthcare professional,
dealer or technical personnel before attempting to use this equipment - otherwise,
injury or damage may occur.
Controller Settings/Repair or Service
 CAUTION
Set-up of the Electronic Control Unit is to be performed only by a qualified techni-
cian. The fine tuning adjustments of the controller may affect other activities of the
wheelchair. Reprogramming the controller reduces the stability/control of the
wheelchair. Other program settings could cause the wheelchair to tip over resulting
in serious injury to the user and/or damage to the surrounding property. If any indi-
vidual other than a qualified technician performs any work on these units, the war-
ranty is void.
Operating Information
Performance adjustments should only be made by professionals of the healthcare field or
persons fully conversant with this process and the driver's capabilities. Incorrect settings
could cause injury to the driver, bystanders, damage to the chair and to surrounding
property.
After the wheelchair has been set-up, check to make sure that the wheelchair performs to
the specifications entered during the set-up procedure. If the wheelchair does not
perform to specifications, turn the wheelchair off immediately and reenter set-up
specifications. Repeat this procedure until the wheelchair performs to specifications.
ALWAYS shift your weight in the direction you are turning. DO NOT shift your weight in
the opposite direction of the turn. Shifting your weight in the opposite direction of the
turn may cause the inside drive wheel to lose traction and the wheelchair to tip over.
DO NOT shift your weight or sitting position toward the direction you are reaching as the
wheelchair may tip over.
DO determine and establish your particular safety limits by practicing bending, reaching
and transferring activities in the presence of a qualified healthcare professional before
attempting active use of the wheelchair.

SECTION 1—GENERAL GUIDELINES
Part No. 1118386 13 P9000™XDT
DO NOT attempt to reach objects if you have to move forward in the seat.
DO NOT attempt to reach objects if you have to pick them up from the floor by reaching
down between your knees.
DO NOT lean over the top of the back upholstery to reach objects from behind as this may
cause the wheelchair to tip over.
DO NOT use an escalator to move a wheelchair between floors. Serious bodily injury may
occur.
Before attempting to transfer in or out of the wheelchair, every precaution should be
taken to reduce the gap distance. Turn both casters parallel to the object you are
transferring onto. Also, be certain the power is off and the wheel locks are engaged to
prevent the wheels from moving.
DO NOT engage or disengage the motor release levers until the power is in the off
position.
Invacare strongly recommends proceeding down ramps or slopes at half speed or slower
and to avoid hard braking or sudden stops.
DO NOT attempt to lift the wheelchair by lifting on any removable (detachable) parts.
Lifting by means of any removable (detachable) parts of a wheelchair may result in injury
to the user or damage to the wheelchair.
Anti-tippers MUST be used at all times. When outdoors on wet, soft ground or gravel
surfaces, anti-tippers may not provide the same level of protection against tipover. Extra
caution must be observed when traversing such surfaces.
Wheel locks are not brakes. DO NOT attempt to stop a moving wheelchair with the wheel
locks.
DO NOT engage or disengage the clutches until the power is in the OFF position.
DO NOT operate on roads, streets or highways.
DO NOT climb, go up or down ramps or traverse slopes greater than 9°.
DO NOT attempt to move up or down an incline with a water, ice or oil film.
DO NOT attempt to drive over curbs or obstacles. Doing so may cause your wheelchair
to turn over and cause bodily harm or damage to the chair.
DO NOT leave the power button in the on position when entering or exiting your
wheelchair.
DO NOT stand on the frame of the wheelchair.
DO NOT use the footplates as a platform. When getting in or out of the wheelchair, make
sure that the footplates are in the upward position or swing the footrests toward the
outside of the chair.
DO NOT stand on the front riggings, otherwise damage may occur. When getting in or
out of the wheelchair, make sure that the footplates on the front riggings are in the
upward position or moved out of the way.
ALWAYS wear your seat positioning strap.

SECTION 1—GENERAL GUIDELINES
P9000™XDT 14 Part No. 1118386
The seat positioning strap is a positioning belt only. It is not designed for use as a safety
device withstanding high stress loads such as auto or aircraft safety belts. If signs of wear
appear, belt must be replaced immediately.
Always verify that hand grips on the rear cane are secure prior to use when an assistant
is used to propel or lift the chair. Check for any signs of looseness or deterioration and if
found, contact a qualified technician. Do not attempt to move the wheelchair by using the
hand grips if they are found to be unsecure or have deteriorated.
When cleaning rear cane or hand grip areas use only a clean towel lightly dampened with
cool water. Verify that grips are dry prior to use. Use of soap or ammonia based cleaning
solutions will result in the hand grips sliding off the cane assembly. Failure to observe this
warning may result in injury to the user or bystanders.
DO NOT sit or transfer into the wheelchair unless it is fully open and the seat frame rails
are fully seated into the side frame H-blocks.
Before performing any maintenance, adjustment or service verify that On/Off switch on
the joystick is in the Off position.
Avoid storage or use near external flame or combustible products.
Tire Pressure
DO NOT use your wheelchair unless it has the proper tire pressure (P.S.I.).
DO NOT overinflate the tires. Failure to follow these suggestions can cause the tire to
explode and cause bodily harm. The recommended tire pressure is listed on the side wall
of the tire.
Electrical Accessories
EXTREME care should be exercised when using oxygen in close proximity to electric
circuits and other combustible materials. Contact your oxygen supplier for instruction in
the use of oxygen.
Batteries
The warranty and performance specifications contained in this manual are based on the
use of deep cycle gel cell or sealed lead acid batteries. Invacare strongly recommends their
use as the power source for this unit.
If wet cell batteries are used, follow all manufacturer guidelines and instructions for
installation and maintenance. Regardless of battery type, proper battery footprint and use
of battery terminal caps as defined in Batteries on page 47 must be followed.
Carefully read battery/battery charger information prior to installing, servicing or
operating your wheelchair.

SECTION 1—GENERAL GUIDELINES
Part No. 1118386 15 P9000™XDT
Charging Batteries
NEVER attempt to recharge the batteries by attaching cables directly to the battery
terminals.
DO NOT attempt to recharge the batteries and operate the wheelchair at the same time.
DO NOT operate wheelchair with extension cord attached to the AC cable.
DO NOT attempt to recharge the batteries when the wheelchair has been exposed to ANY
type of moisture.
DO NOT attempt to recharge the batteries when the wheelchair is outside.
DO NOT sit in the wheelchair while charging the batteries.
DO NOT attempt to recharge batteries using at the same time BOTH the on-board battery
charger AND an independent battery charger plugged into the joystick charger port.
Doing so will reduce the life of the batteries.
READ and carefully follow the manufacturer’s instructions for each charger (supplied or
purchased). If charging instructions are not supplied, consult a qualified technician for
proper procedures.
After charging batteries, ALWAYS make sure that the battery charger cord is unplugged.
Failure to do this could result in damage to the cord or personal injury to the user or
bystanders.
When using an extension cord, use only a three (3) wire extension cord having at least 16
AWG (American Wire Gauge) wire and the same or higher electrical rating as the device
being connected.
Use of improper extension cord could result in risk of fire and electric shock.
Ensure the pins of the extension cord plug are the same number, size, and shape as those
on the charger.
DO NOT under any circumstances cut or remove the round grounding plug from the
charger AC cable plug or the extension cord plug.
Three (3) prong to two (2) prong adapters should not be used. Use of three (3) prong
adapters can result in improper grounding and present a shock hazard to the user.
Grounding Instructions
DO NOT, under any circumstances, cut or remove the round grounding prong from any
plug used with or for Invacare products. Some devices are equipped with three-prong
(grounding) plugs for protection against possible shock hazards and fire. Where a
two-prong wall receptacle is encountered, it is the personal responsibility and obligation
of the customer to contact a qualified electrician and have the two-prong receptacle
replaced with a properly grounded three-prong wall receptacle in accordance with the
National Electrical Code. If you must use an extension cord, use ONLY a three-wire
extension cord having the same or higher electrical rating as the device being connected.
In addition, Invacare has placed RED/ORANGE warning tags on some equipment. DO
NOT remove these tags.

SECTION 1—GENERAL GUIDELINES
P9000™XDT 16 Part No. 1118386
Rain Test
Invacare has tested its power wheelchairs in accordance with ISO 7176 “Rain Test.” This
provides the end user or his/her assistant sufficient time to remove his/her power
wheelchair from a rain storm and retain wheelchair operation.
DO NOT leave power wheelchair in a rain storm of any kind.
DO NOT use power wheelchair in a shower or leave it in a damp bathroom while taking
a shower.
DO NOT store power wheelchair in a damp area for an extended period of time.
Direct exposure to excessive rain or dampness may cause the chair to malfunction
electrically and mechanically, may cause the chair to prematurely rust or may damage the
upholstery.
Check to ensure that the RED and GREY battery terminal caps are secured in place,
joystick boot is NOT torn or cracked where water can enter and that all electrical
connections are secure at all times.
DO NOT use the wheelchair if the joystick boot is torn or cracked. If the joystick boot
becomes torn or cracked, replace IMMEDIATELY.
Weight Training
Invacare DOES NOT recommend the use of its wheelchairs as a weight training
apparatus. Invacare wheelchairs have not been designed or tested as a seat for any kind
of weight training. If occupant uses said wheelchair as a weight training apparatus,
Invacare shall NOT be liable for bodily injury and the warranty is void.
Weight Limitation
The P9000 XDT has a weight limitation, including seating system and accessories, of 250
lbs. Refer to Percentage of Weight Distribution on page 23. Invacare recommends that
only heavy-duty wheelchairs should be used for individuals weighing more than 250 lbs.
Further, the activity level of the individual wheelchair user is important. For instance, a
170 lb. active wheelchair could subject the wheelchair to more stress than a 250 lb. user.
Invacare recommends that very active users consider the use of heavy-duty wheelchairs.

SECTION 2—EMI INFORMATION
Part No. 1118386 17 P9000™XDT
SECTION 2—EMI INFORMATION
 WARNING
CAUTION: IT IS VERY IMPORTANT THAT YOU READ THIS INFORMATION
REGARDING THE POSSIBLE EFFECTS OF ELECTROMAGNETIC
INTERFERENCE ON YOUR POWERED WHEELCHAIR.
Electromagnetic Interference (EMI) From Radio Wave Sources
Powered wheelchairs and motorized scooters (in this text, both will be referred to
as powered wheelchairs) may be susceptible to electromagnetic interference (EMI),
which is interfering electromagnetic energy (EM) emitted from sources such as
radio stations, TV stations, amateur radio (HAM) transmitters, two way radios, and
cellular phones. The interference (from radio wave sources) can cause the powered
wheelchair to release its brakes, move by itself, or move in unintended directions. It
can also permanently damage the powered wheelchair's control system. The
intensity of the interfering EM energy can be measured in volts per meter (V/m).
Each powered wheelchair can resist EMI up to a certain intensity. This is called its
"immunity level." The higher the immunity level, the greater the protection. At this
time, current technology is capable of achieving at least a 20 V/m immunity level,
which would provide useful protection from the more common sources of radiated
EMI.
There are a number of sources of relatively intense electromagnetic fields in the
everyday environment. Some of these sources are obvious and easy to avoid.
Others are not apparent and exposure is unavoidable. However, we believe that by
following the warnings listed below, your risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1) Hand-held Portable transceivers (transmitters-receivers with the antenna
mounted directly on the transmitting unit. Examples include: citizens band (CB)
radios, "walkie talkie", security, fire and police transceivers, cellular telephones,
and other personal communication devices).
NOTE: Some cellular telephones and similar devices transmit signals while they are ON,
even when not being used.
2) Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances and taxis. These usually have the antenna mounted on the outside of
the vehicle; and
3) Long-range transmitters and transceivers, such as commercial broadcast
transmitters (radio and TV broadcast antenna towers) and amateur (HAM)
radios.
NOTE: Other types of hand-held devices, such as cordless phones, laptop computers,
AM/FM radios, TV sets, CD players, cassette players, and small appliances, such as
electric shavers and hair dryers, so far as we know, are not likely to cause EMI problems
to your powered wheelchair.

SECTION 2—EMI INFORMATION
P9000™XDT 18 Part No. 1118386
 WARNING
Powered Wheelchair Electromagnetic Interference (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the
transmitting antenna (source), the EM fields from hand-held radio wave sources
(transceivers) are of special concern. It is possible to unintentionally bring high
levels of EM energy very close to the powered wheelchair's control system while
using these devices. This can affect powered wheelchair movement and braking.
Therefore, the warnings listed below are recommended to prevent possible
interference with the control system of the powered wheelchair.
Electromagnetic interference (EMI) from sources such as radio and TV stations,
amateur radio (HAM) transmitters, two-way radios, and cellular phones can affect
powered wheelchairs and motorized scooters.
FOLLOWING THE WARNINGS LISTED BELOW SHOULD REDUCE THE
CHANCE OF UNINTENDED BRAKE RELEASE OR POWERED WHEELCHAIR
MOVEMENT WHICH COULD RESULT IN SERIOUS INJURY.
1) Do not operate hand-held transceivers (transmitters receivers), such as citizens
band (CB) radios, or turn ON personal communication devices, such as cellular
phones, while the powered wheelchair is turned ON;
2) Be aware of nearby transmitters, such as radio or TV stations, and try to avoid
coming close to them;
3) If unintended movement or brake release occurs, turn the powered wheelchair
OFF as soon as it is safe;
4) Be aware that adding accessories or components, or modifying the powered
wheelchair, may make it more susceptible to EMI.
NOTE: There is no easy way to evaluate their effect on the overall immunity of the
powered wheelchair).
5) Report all incidents of unintended movement or brake release to the powered
wheelchair manufacturer, and note whether there is a source of EMI nearby.
Important Information
1) 20 volts per meter (V/m) is a generally achievable and useful immunity level
against EMI (as of May 1994) (the higher the level, the greater the protection);
2) The immunity level of the product is unknown.
Modification of any kind to the electronics of this wheelchair as manufactured by
Invacare may adversely affect the RFI immunity levels.

SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS
Part No. 1118386 19 P9000™XDT
SECTION 3—SAFETY/HANDLING OF
WHEELCHAIRS
“Safety and Handling” of the wheelchair requires the close attention of the wheelchair
user as well as the assistant. This manual points out the most common procedures and
techniques involved in the safe operation and maintenance of the wheelchair. It is
important to practice and master these safe techniques until you are comfortable in
maneuvering around the frequently encountered architectural barriers.
Use this information only as a “basic” guide. The techniques that are discussed on the
following pages have been used successfully by many.
Individual wheelchair users often develop skills to deal with daily living activities that
may differ from those described in this manual. Invacare recognizes and encourages each
individual to try what works best for him/her in overcoming architectural obstacles that
they may encounter. However, all warnings and cautions given in this manual MUST be
followed. Techniques in this manual are a starting point for the new wheelchair user and
assistant with “safety” as the most important consideration for all.
Stability and Balance
 WARNING
ALWAYS wear your seat positioning strap.
The seat positioning strap is a positioning belt only. It is not designed for use as a
safety device withstanding high stress loads such as auto or aircraft safety belts. If
signs of wear appear, belt MUST be replaced immediately.
To assure stability and proper operation of your wheelchair, you must at all times
maintain proper balance. Your wheelchair has been designed to remain upright and
stable during normal daily activities as long as you do not move beyond the center of
gravity. DO NOT lean forward out of the wheelchair any further than the length of the
armrests.
Coping With Everyday Obstacles
Coping with the irritation of everyday obstacles can be alleviated somewhat by learning
how to manage your wheelchair. Keep in mind your center of gravity to maintain stability
and balance.
While the walking beam allows you to traverse up to a 2-inch bump or threshold,
stopping after the wheels cross the bump poses a problem. The chair cannot reverse over
the bump at this point. Continue forward and then turn around.

SECTION 3—SAFETY/HANDLING OF WHEELCHAIRS
P9000™XDT 20 Part No. 1118386
While the P9000 XDT is designed for use primarily in and around the home, the provider
should determine whether this chair is suitable for the actual environment the chair will
be used in.
DO NOT go down ramp at full speed. Some seat/back positions will cause wheelchair to
feel unstable.
 CAUTION
Be aware of condition of ramp. Traction will be diminished/nonexistent on a slip-
pery surface. Proceed with caution.
A Note to Wheelchair Assistants
When assistance to the wheelchair user is required, remember to use good body
mechanics. Keep your back straight and bend your knees whenever tilting wheelchair or
traversing curbs or other impediments.
Also, be aware of detachable parts such as arms or legrests. These must NEVER be used
to move the wheelchair or as lifting supports, as they may be inadvertently released,
resulting in possible injury to the user and/or assistant(s).
When learning a new assistance technique, have an experienced assistant help you before
attempting it alone.
Tipping
 WARNING
DO NOT tip the wheelchair without assistance.
When tipping the wheelchair, an assistant should grasp the back of the wheelchair on a
non-removable (non-detachable) part. Inform the wheelchair occupant before tipping the
wheelchair and remind him/her to lean back. Be sure the occupant’s feet and hands are
clear of all wheels.
Tipping - Curbs
After mastering the techniques of tipping the wheelchair, use this procedure to tackle
curbs, short stairs, etc.
This procedure requires two (2) assistants. The second assistant should be positioned at
the front of the wheelchair lifting upward on a non-removable (non-detachable) part of
the wheelchair frame when lifting the wheelchair and stabilizing the wheelchair when the
wheelchair is being lowered to the ground.
The first assistant should turn the anti-tippers so the wheels are pointing up, apply a
continuous downward motion until the balance point is achieved and the front casters
clear the curb. At this point, the assistants will feel a difference in the weight distribution.