45
CONTROL PADS ON THE DEHUMIDIFIER
NOTE:The control panelof the unityou purchased maybe slightly dierentaccording to the
models.
Fig.1
CONTROL PADS ON THE DEHUMIDIFIER
Other features
BucketFull Light
Glowswhenthebucket is readyto be
emptied.
Whenfrost buildsupontheevaporatorcoils, the
compressorwill cycle o andthefanwill continue
to rununtil thefrost disappears.
Auto Defrost
Wait 3 minutesbefore resuming operation
After the unit has stopped, it will not restart operation
for three minutes. This is to protect the unit.
Operation will automatically start after 3 minutes.
Setting theTimer
When the unit ison, rst press the Timer
button, theTimer Oindicator light
illuminates. It indicates theAutoStop
program is initiated. Press it again and the
TimeOn indecator lightilluminates.It
indicates theAutoStart is initiated.
Press or hold theUPor DOWN pad to
change theAutotime by 0.5hour incre-
ments, up to10 hours, then at 1hour
increments upto 24hours. The control
will countdown the time remaining until
start.
The selected timewill register in 5seconds
and the systemwill automatically revert
back to display the previous humidity
setting.
When theAutostart&Autostop timesare
set, within the same program sequence,
TIMER ON OFF indicator lights illuminate
identifying both ONand OFF times are
now programmed.
Turning the unitON or OFFat any timeor
adjusting thetimer settingto 0.0 willcancel
theAutoStart/Stop function.
When the LEDdisplay window displays the
code of P2, theAutoStart/Stop function
will also becancelled.
When the unit iso,rst press theTimer
button, theTIMER ON indicator light
illuminates. It indicates theAutoStart
program is initiated. Press it again and the
TimeOindecator lightilluminates.It
indicates theAutoStop is initiated.
Checklterfeature
Thesystem startsto count thetimeoncethefan
motoroperates. Thechecklterfeature canbe
only activatedwhentheaccumulatedoperation
timeachieves250hours ormore. TheReset
light(Cleanlterindicatorlight) ashesat onetime
persecond, afternishingcleantheair lter,press
theFilterpadandtheReset light(Cleanlterindicator
light) goeso.
Auto ShutO
Thedehumidiershuts o whenthebucket is
full, or when the bucket is removed or not replaced
in the proper position. When the set humidity level
is reached, the unit will be shut o automatically.
For some models,the fan motor will continue
operating.
Auto-Restart
If the unit turns o unexpectedly due to a power outage,
it will restart with the previously set functions automatically
when the power resumes.
High fan
indicator light
On
O
Full
3
Clean lter
indicator light
Continuous
operation on
indicator light
Timer on/o
indicator light
12
Auto defrost
4 5 6 7 8
9
Auto defrost operation
on indicator light
Bucket full
indicator light
Comfort dehumidifying
operation on
indicator light
Pump operation
on indicator light
Control pads
When you pushthe button tochange
operation modes, theunit will make
a beep soundto indicate thatit is
changing modes.
Humidity Set Control Pads
77: Up/Down Pads
TIMER Set Control Pads
Use the Up/Down pads to set the Auto
start and Auto stop time from 0.0 to 24.
The humidity level can be set within a range of
35%RH(Relative Humidity) to 85%RH(Relative
Humidity) in 5% increments.
For drier air,press the pad and set to a lower
percent value(%).
For damper air,press the pad and set a higher
percent value(%).
66
Timer Pad
Press to initiate the Auto start and Auto stop feature,
in conjuction with the and key pads.
11
PUMP Pad(on some models)
88
Power Pad
Press to turn the dehumidier on and o.
Press to activate the pump operation.
NOTE: Make sure the pump drain hose is installed
into the unit and the continuous drain hose is removed
fromthe unit before the pump operation is activated.
When the bucket is full, the pump starts to work.Refer
to the next pages for removing the collected water.
Do not use this operation when the outdoor temperature
is equel to or less than 0 C (32 F).
22
COMFORT Pad(optional)
Press to activate the comfort dehumidifying operation.
NOTE: In this operation, the unit's humidity level can not
be set.
33
FILTER Pad
The check lter feature is a reminder to clean the
Air Filter for more ecient operation. The Filter
light(Clean lter l ight) will illuminate after 250 hours
of operation. Toreset after cleaning the lter, press
the Filter pad and the light will go o.
44
CONTINUE Pad
Press to activate the c
ontinuous dehumidifying operation.
55
TURBO Pad
Control the fan speed. Press to select either High
or Normal fan speed. Set the fan control to High for
maximum moisture removal. When the humidity has
been reduced and quiet operation is preferred, set
the fan control to Normal.
9
Display
Shows the set % humidity level from 35% to 85% or auto
start/stop time (0~24) while setting, then shows the actual
( 5% accuracy) room % humidity level in a range of 30%
RH(Relative Humidity) to 90%RH(Relative Humidity).
Error Codes and Protection Code:
AS - Humidity sensor error--Unplug the unit and plug it back
in. If error repeats, call for service.
ES - Tube Temperature sensor of the evaporator error-- Unplug
the unit and plug it back in. If error repeats, call for service.
P2- Bucket is full -- Empty the bucket.(only available for the
unit with pump feature.)
EC - Refrigerant leakage detection-- With this new technology,
the display area will appear EC when the unit detects
refrigerant leakage, call for service.
E3 - Unit malfunction-- Unplug the unit and plug it back in. If
error repeats, call for service.
Eb - Bucket is removed or not in right position-- Replace the
bucket in the right position.(only available for the unit with
pump feature.)