inVue 1500 Series User manual

Series 1500
Puck & Stand
HC15000, HC15001, HC15002
All manuals and user guides at all-guides.com

2
Read entire instruction guide before starting installation.
System Components
1. Puck/Stand
2. Mounting Plate
3. Recoiler
4. Sensor
5. IR Key (not included)
6. Power connector (if powering up merchandise, order separately)
7. Power Supply (if powering up merchandise, order separately)
Tools
1. T-20 Bit
2. Drill
System Overview
The Series 1500 secures and displays your handheld and
tablet merchandise.
All manuals and user guides at all-guides.com

3
5
10
20
30
InVue IR Key
AF4400 or PK4400
Screwdriver & T-20 Bit Drill
Sensor
Puck/Stand
HC15000 - Flat Puck
HC15001 - Angled Stand
HC15002 - Angled Puck
Power Supply
PS18VUS - US
PS18VEU - EU
PS18VAUS - AUS
PS18VUK - UK
PS18VARG - ARG
Power Connector
Recoiler
HC15405
Mounting Plate
HC15406
All manuals and user guides at all-guides.com

4
Attaching Puck to Display Counter
Adhesive Mount
(See page 5)
Screw Mount
(See page 7)
All manuals and user guides at all-guides.com

5
1Drill a 19 mm (0.75”) hole in display counter. If
displaying more than one puck/stand: Drill a 19 mm
(0.75”) hole a minimum of 152 mm (6”) apart. Wipe
display counter with alcohol wipe provided. Let it dry
completely.
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
5
10
20
30
All manuals and user guides at all-guides.com

6
2Remove film from adhesive. Align puck directly over
hole in display counter and press firmly for at least 10
seconds. “InVue” on bottom of puck/stand must be
facing back of display counter.
All manuals and user guides at all-guides.com

7
Attaching Puck to Display Counter – Screw Mount
All manuals and user guides at all-guides.com

8
1Drill a 19 mm (0.75”) hole in display counter. If display-
ing more than one puck/stand: Drill a 19 mm (0.75”)
hole a minimum of 152 mm (6”) apart.
5
10
20
30
All manuals and user guides at all-guides.com

9
2Cut out template on page 38 to mark drill hole location
for threaded rod. Drill a 7.5 mm (0.3”) hole into display
counter.
FRONT OF STAND
BACK OF STAND
19.00 mm (3/4")
7.50 mm (5/16")
13.80 mm
15.40 mm
All manuals and user guides at all-guides.com

10
3Screw threaded rod into bottom of puck/stand. Remove
film from adhesive. Place threaded rod through display
counter and press firmly for at least 10 seconds. Tighten
wingnut below counter.
All manuals and user guides at all-guides.com

11
Attaching Mounting Plate & Recoiler
(Below counter installation)
Adhesive Mount -
Use only if screw mount
cannot be used
(See page 15)
Mounting Plate
Recoiler
Jack
Screw Mount -
Recommended
(See page 12)
All manuals and user guides at all-guides.com

12
1Fit opening in mounting plate to hole in display counter.
Use mounting plate as template to drill all 3 holes for
screws. Tighten all 3 screws with screwdriver.
All manuals and user guides at all-guides.com

13
2Feed jack through hole in mounting plate and push
through puck/stand. Snap recoiler to mounting plate.
Jack will remain locked in puck/stand once pushed
through.
All manuals and user guides at all-guides.com

14
3If powering merchandise: Plug power supply into
mounting plate cord and into outlet.
All manuals and user guides at all-guides.com

15
Attaching Mounting Plate & Recoiler – Adhesive Mount
(Use only if screw mount cannot be used)
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
All manuals and user guides at all-guides.com

16
1Remove film from adhesive on mounting plate. Fit
opening in mounting plate to hole in display counter.
Press firmly for at least 10 seconds.
All manuals and user guides at all-guides.com

17
2Feed jack through hole in mounting plate and push
through puck/stand. Snap recoiler to mounting plate.
Jack will remain locked in puck/stand once pushed
through.
All manuals and user guides at all-guides.com

18
3If powering merchandise: Plug power supply into
mounting plate cord and into outlet.
All manuals and user guides at all-guides.com

19
Attaching Sensor
Sensor without Bracket Arms
(See page 20)
Sensor with Bracket Arms
(See page 25)
All manuals and user guides at all-guides.com

20
1Wipe back of merchandise with alcohol wipe provided.
Let it dry completely.
CONTENTS: One pad saturated in
Isopropyl Alcohol
75%
DIRECTIONS: Apply topically as
needed to cleanse surface mounting area.
FOR EXTERNAL USE ONLY
KEEP OUT OF REACH OF
CHILDREN
KEEP AWAY FROM EYES
AND FIRE
All manuals and user guides at all-guides.com