Invue Live dld220 User manual

For technical assistance call

NA / LATAM // 704.752.6513 •888.55.INVUE

EMEA // +31.23.8900150

APAC // +852.3127.6811

LIVE Panic Button DLD220

5Once successfully enrolled in the

app, pull the battery tab from the

panic button.

3Use the smart phone or tablet’s

camera to scan the barcode on the

Panic Button (the Device ID can

also be entered manually). Follow

the prompts in the app to set up

the button.

1If not already installed on your

smart phone or tablet, download

the InVue LIVE Display app from

the Google Play store. Log in using

the information provided by your

manager or admin.

2With the InVue LIVE Display app

open on your smart phone or

tablet, press the “Add or Scan

InVue Device” button.

IMPORTANT:

Do NOT remove the battery

tab until the Panic Button

has been successfully

enrolled into the InVue LIVE

App.

If you already have login

information for the app proceed

to the next step.

Otherwise, see below.

First time setup

Before using the app, users and site

information must be set up within the InVue

LIVE web portal.

This should be completed by a manager or

admin using the information sent by InVue

Customer Service.

If you are a manager or admin and have not

received this information via email from InVue

Customer service, please submit a service

request.

4a To check that the Panic Button

has been successfully enrolled,

click the menu icon at the top of

the screen.

4b Select “Panic Buttons” from the

drop-down menu to check status

and/or make changes.

For technical assistance call

NA / LATAM // 704.752.6513 •888.55.INVUE

EMEA // +31.23.8900150

APAC // +852.3127.6811

SD0818 Rev1 07/19/22

LIVE Panic Button DLD220

7Once successfully enrolled in the app, the Panic button

may be used to lock down all assigned OnePOD LIVE

positions at once. These positions will remain locked for

a preset duration of time that was set within the InVue

LIVE Admin Portal. A red banner will appear at the top of

the app showing the time remaining. The positions will

automatically unlock once this time expires.

6Press the red button to complete

activation. The LED will illuminate

red. Any lockable sensors may

respond to this button press.

Note: It may take several minutes

for the app to refresh and allow

regular use of the panic button.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

ISED Regulatory Compliance

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes :

(1) L’appareil ne doit pas produire de brouillage;