ION ISP32 User manual

Rock Speaker Bluetooth
Quickstart Guide
English ( 3 - 5 )
Appendix
English ( 6 )

3
Quickstart Guide (English)
1. Make sure all items listed in the BOX CONTENTS are included in the
box.
2. READ SAFETY INSTRUCTION BOOKLET BEFORE USING THE
PRODUCT.
3. MAKE SURE THAT YOU HAVE COMPLETELY CHARGED THE
BATTERY PRIOR TO FIRST USE FOR MAXIMUM BATTERY LIFE.
For additional product support, visit ionaudio.com/support
For safety/warranty information, visit ionaudio.com/warranty
Introduction
Thank you for purchasing the ION Audio Rock Speaker
Bluetooth! Rock Speaker Bluetooth simulates a natural rock
finish that blends into your landscaping, with a rechargeable
battery-powered, water-resistant speaker. Equipped with
Bluetooth® technology, you can listen to your favorite music
wirelessly while working in the garden, hosting a dinner
party, or relaxing by the pool.
Rechargeable Batteries
Rechargeable lead-acid batteries are the same type used in automobiles. As with your car battery, how you use this
battery has a significant impact on its lifespan. With proper use and treatment, a lead-acid battery can last for years.
Here are some recommendations for getting the longest life from the internal battery.
GENERAL USAGE
•FULLY CHARGE THE BATTERY BEFORE USING IT.
•CHARGE THE BATTERY COMPLETELY AFTER EACH USE.
STORAGE
•For best product longevity, do not store at exceedingly hot (greater than 90F (32C)) or exceedingly cold
(less than 32F (0C)) temperatures.
•It is acceptable to leave your sound system plugged in. This will not overcharge the battery.
•If you leave the battery level low and do not charge it for 6 months, it may permanently lose capacity.
REPAIR
•If the battery fails to charge, check your fuse near the power cable input. If your fuse is intact and it still
will not charge, contact ION Audio at ionaudio.com.
DISPOSAL
•Bring the unit to a recycling center or dispose of in accordance with local ordinances.
MICROPHONE
BOX CONTENTS
Rock Speaker Bluetooth
Charging Adapter
Quickstart Guide
Safety & Warranty Information
Booklet
WARNING: Keep any non-water-resistant
devices (phones, music players, etc.) in a dry
place where they will not be affected by water
and cause a risk of electric shock.

4
Parts Description
1. Power – Hold this button to power Rock Speaker Bluetooth on and
off.
2. Bluetooth Connect –Press this button to begin Bluetooth
connecting.
Note: Rock Speaker Bluetooth will automatically power off after 30
minutes if no device is connected. After 2 hours of no music
playing, Rock Speaker Bluetooth will automatically power off, even
if still connected.
3. Link –Press this button to link two Rock Speaker Bluetooth
units together.
4. Charging Adapter Input – Insert the included charging
adapter here to charge the Rock Speaker Bluetooth battery.
5. Reset –If Rock Speaker Bluetooth is working abnormally,
shutdown the unit by placing a paperclip into the Reset hole
located on the bottom of Rock Speaker Bluetooth, and gently
push until the unit turns off. Try this only after you have first
attempted to reboot Rock Speaker Bluetooth using the power
button.
6. Charging LED – This LED is solid red when the battery is
charging and turns off when the battery is fully charged/no
adapter is connected.
7. Bluetooth LED – This LED slowly blinks blue when the
speaker is powered on, blinks fast while Bluetooth searching,
and is solid when Bluetooth connected.
8. Link LED – This LED blinks fast when searching for another
Rock Speaker Bluetooth and is solid when linked to another
Rock Speaker Bluetooth.
Bluetooth Connecting with Rock Speaker Bluetooth
Connecting to one Rock Speaker Bluetooth:
1. Power on Rock Speaker Bluetooth by holding down the power button. A tone will be heard when powering on.
2. Press the Bluetooth Connect button to enter Connecting Mode.
Navigate to your device’s Bluetooth setup screen, find Rock Speaker Bluetooth, and connect. Rock Speaker Bluetooth
LED will light up solid when it is connected and play a tone.
Note: If you experience trouble in connecting, select “Forget this Device” on your Bluetooth device and try to connect
again.
Note: Consider updating your device’s OS if you experience trouble with connecting or playing music.
3. To disconnect, hold the Bluetooth Connect button on Rock Speaker Bluetooth. A tone will be heard when
disconnecting.
4. If your Bluetooth device is not able to connect to Rock Speaker Bluetooth, hold the Bluetooth Connect button on the
speaker to break previous Bluetooth connections and reset the Bluetooth module.
Linking two Rock Speaker Bluetooth units:
Note: Ensure that the speakers are not already Bluetooth connected in single mode. If either of them is connected, hold the
Bluetooth Connect button to disconnect and then follow the steps below.
1. Power on each Rock Speaker Bluetooth by holding down their power buttons. A tone will be heard from each speaker
when powering on.
2. Press the Link button on each Rock Speaker Bluetooth. The speakers will search for each other while playing an
intermittent tone. Once found, they will play a tone to confirm they are linked. This may take up to 2 minutes the first time
two speakers are linked.
Note: When the speakers are linked, the Bluetooth identifier name will change from Rock Speaker Bluetooth to Rock
Speaker Pair.
3. Press the Bluetooth Connect button on the Rock Speaker Bluetooth that you want to be the "master" (left channel).
This is the unit that your device will connect to, and the unit from which the Bluetooth range will be determined.
4. Navigate to your device’s Bluetooth setup screen, find Rock Speaker Pair, and connect. A tone will be heard when
connected.
Note: If you experience trouble in connecting, select “Forget this Device” for Rock Speaker Pair on your Bluetooth
device and try to connect again.
Note: Consider updating your device’s OS if you experience trouble with connecting or playing music.
5. To disconnect linking, hold the Link button on the “master” Rock Speaker Bluetooth for 5 seconds. A tone will be heard
when disconnecting.
6. If your Bluetooth device is not able to connect to Rock Speaker Bluetooth, hold the Bluetooth Connect button on the
speaker to break previous Bluetooth connections and reset the Bluetooth module.
Note: When two speakers are linked, hold the power button on one speaker to turn both speakers off. The speakers will
relink automatically the next time they are both powered on.
Rock Speaker Bluetooth LED
activity:
Solid Red Charging LED = Battery is
charging, LED turns off when charging
is full or when no adapter is
connected.
Solid Blue Bluetooth LED =
Connected to a Bluetooth device.
Blinking Blue Bluetooth LED =
Blinks slow when powered on. Fast
blinking when searching for Bluetooth
devices to connect to.
Solid Link LED = Linked to another
Rock Speaker Bluetooth.
Blinking Link LED = Blinks fast when
searching for another Rock Speaker
Bluetooth to link to.
2
13
45
LINK
78
6

5
Appendix (English)
Specifications
Charging Adapter: 15V, 2000mA
Battery: Built-in rechargeable 12V lead-acid battery
Battery Life: Up to 48 hours*
* Battery life may vary based on temperature, age, and volume usage of product.
Speaker Output: 20 Watts (Peak)
Time required to fully charge: 5.5 hours
Water-resistant class: IPX Level 4
Supported Bluetooth Profile: A2DP
Bluetooth Range: 30 feet
Trademarks and Licenses
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by ION
Audio is under license.
All other product or company names are trademarks or registered trademarks of their respective owners.

ionaudio.com
Manual Version 1.0

IMPORTANT SAFETY INSTRUCTIONS
&
WARRANTY I NFOR M ATI ON
ENGLISH ( 3 – 13 )
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
E
INFORMACIÓNDE LA GA RANTÍA
ESPAÑOL ( 14 – 21 )
INSTRUCTIONS IMPORTANTES DE SÉCURITÉ
ET
INFORMATIONS DE G ARANTIE
FRANÇ AIS ( 22 – 29 )
ISTRUZIONI IMPORTANTI DI SICUREZZA E
LE
INFORMAZIONI DELLA GARANZIA
ITALIANO ( 30 – 37 )
WICHTIGE SICHERHEITSANWEISUNGEN UN
D
GARANTIEINFORMATIONEN
DEUTSCH ( 38 – 45 )

2

PRODUCT WARRANTY (U.S.A.)
1. What is covered and for how long?
ALL PRODUCTS: inMusic Brands, Inc. ("inMusic") warrants to the original
purchaser that ION Audio products and all other accessories are free
from defects in material and workmanship under normal use and service
for the period commencing upon the date of purchase from an authorized
ION Audio dealer and continuing for the following period of time after that
date for ninety (90) days. ION Audio warrants factory-refurbished
merchandise to be free of material and operational defects for a period of
ninety (90) days from the original date of retail sale. This refurbished
merchandise warranty is not transferable.
2. What is not covered? This Limited Warranty is conditioned upon proper use of
the product by the purchaser. This Limited Warranty does not cover:
ƒDamage caused by improper installation or improper connection to
any peripheral
ƒDamage caused by an external electrical fault
ƒDamage from use of parts not manufactured or sold by ION Audio
ƒProduct purchased from anyone other than an ION Audio
authorized dealer
ƒModifications to product not approved in writing by ION Audio
ƒEquipment that has the serial number removed or made illegible
ƒNormal cosmetic and mechanical wear
ƒDamage or loss during transit to an Authorized ION Audio Repair Center
ƒUnits that are purchased and/or located outside of the continental USA
3

3. What are inMusic's obligations? During the applicable warranty period, ION
Audio will repair or replace, at ION Audio's sole option, without charge to the
purchaser, any defective component part of the product. To obtain service
under this Limited Warranty, purchaser must first contact ION Audio and obtain
a return authorization number ("RA#"). Purchaser must then return the product
to ION Audio in an adequate container for shipping, accompanied by
purchaser's sales receipt or comparable proof of sale showing the date
of purchase, the serial number of the product, and the seller's name and
address. To obtain an RA# and assistance on where to return the product,
contact ION Audio customer service at 401-658-3743. Upon receipt, ION Audio
will repair or replace the defective products. ION Audio may, at ION Audio's
sole option, use rebuilt, reconditioned, or new parts or components when
repairing any product or replace a product with a rebuilt, reconditioned, new or
comparable product. Repaired products will be warranted for a period equal to
the remainder of the original Limited Warranty on the original product or for
90 days, whichever is longer. All replaced parts, components, boards, and
equipment become the property of ION Audio. If ION Audio determines that
any product is not covered by this Limited Warranty, purchaser must pay all
parts, shipping, and labor charges for the repair or return of such product.
4. What are the limits on inMusic's liabilities? THE WARRANTIES GIVEN IN
THIS LIMITED WARRANTY, TOGETHER WITH ANY IMPLIED WARRANTIES
COVERING ION AUDIO PRODUCTS, INCLUDING WITHOUT LIMITATION
ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS
LIMITED WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY
APPLICABLE LAW, INMUSIC OR ION AUDIO SHALL NOT BE LIABLE FOR
ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR
DAMAGES, LOSS OF PROFITS, DAMAGES TO PURCHASER'S PROPERTY,
OR INJURY TO PURCHASER OR OTHERS ARISING OUT OF THE USE,
MISUSE OR INABILITY TO USE ANY ION AUDIO PRODUCT, BREACH
OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT NOT LIMITED TO
INMUSIC'S OR ION AUDIO'S OWN NEGLIGENCE, EVEN IF INMUSIC,
ION
4

AUDIO, OR THEIR AGENTS HAVE BEEN ADVISED OF SUCH
DAMAGES, OR FOR ANY CLAIM BROUGHT AGAINST PURCHASER BY
ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE COMPLETE
WARRANTY FOR ION AUDIO PRODUCTS, AND IS GIVEN IN LIEU OF ALL
OTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL
NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER
OF THIS PRODUCT AND STATES PURCHASER'S EXCLUSIVE REMEDY.
IF ANY PORTION OF THIS LIMITED WARRANTY IS ILLEGAL OR
UNENFORCEABLE BY REASON OF ANY LAW, SUCH PARTIAL ILLEGALITY
OR UNENFORCEABILTY SHALL NOT AFFECT THE ENFORCEABILITY
OF THE REMAINDER OF THIS LIMITED WARRANTY WHICH
PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE CONSTRUED
TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
This Limited Warranty allocates risk of product failure between purchaser and
ION Audio, and ION Audio's product pricing reflects this allocation of risk and
the limitations of liability contained in this Limited Warranty. The agents,
employees, distributors, and dealers of ION Audio are not authorized to make
modifications to this Limited Warranty, or make additional warranties binding on
ION Audio or inMusic. Accordingly, additional statements such as dealer
advertising or presentation, whether oral or written, do not constitute warranties
by ION Audio or inMusic and should not be relied upon.
5. How does state law apply to this warranty? SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATIONS OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES OR HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY
NOT APPLY TO PURCHASER.
This Limited Warranty gives you specific legal rights. You may also have other rights,
which vary from one jurisdiction to another.
5

PRODUCT WARRANTY
(NON - U .S.A.)
1. inMusic Brands, Inc. ("inMusic") warrants to the original purchaser that ION Audio products
are free from defects in material and workmanship under normal use and service for
the period commencing upon the date of purchase from an authorized ION Audio
dealer and continuing for the following period of time after that date for (1) Year.
2. This Limited Warranty is conditioned upon proper use of the product by the purchaser.
This Limited Warranty does not cover: (a) defects or damage resulting from accident, misuse,
abuse, neglect, unusual physical or electrical stress, modification of any part of the product,
or cosmetic damage; (b) equipment that has the serial number removed or made illegible; (c)
all plastic surfaces and other externally exposed parts that are scratched or damaged due to
normal use; (d) defects or damage from improper testing, operation, maintenance,
installation, adjustment, or service of the products.
3. During the applicable warranty period, ION Audio will repair or replace, at ION Audio's sole
discretion, without charge to the purchaser, any defective component part of the product. ION
Audio may, at ION Audio's sole discretion, use rebuilt, reconditioned, or new parts or
components when repairing any product or replace a product with a rebuilt,
reconditioned, new or comparable product.
4. THE WARRANTIES GIVEN IN THIS LIMITED WARRANTY, TOGETHER WITH ANY
IMPLIED WARRANTIES COVERING ION AUDIO PRODUCTS, INCLUDING WITHOUT
LIMITATION ANY WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED
WARRANTY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW,
INMUSIC OR ION AUDIO SHALL NOT BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES, LOSS OF
PROFITS, DAMAGES TO PURCHASER'S PROPERTY, OR INJURY TO PURCHASER
OR OTHERS ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE ANY ION
AUDIO PRODUCT, BREACH OF WARRANTY, OR NEGLIGENCE, INCLUDING BUT
NOT LIMITED TO INMUSIC'S OR ION AUDIO'S OWN NEGLIGENCE, EVEN IF
INMUSIC, ION AUDIO, OR ITS AGENTS HAVE BEEN ADVISED OF SUCH DAMAGES,
OR FOR ANY CLAIM BROUGHT AGAINST
6

PURCHASER BY ANY OTHER PARTY. THIS LIMITED WARRANTY IS THE
COMPLETE WARRANTY FOR ION AUDIO'S PRODUCTS, AND IS GIVEN IN LIEU
OF ALL OTHER EXPRESS WARRANTIES. THIS LIMITED WARRANTY SHALL NOT
EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS
PRODUCT AND STATES PURCHASER'S EXCLUSIVE REMEDY. IF ANY PORTION OF
THIS LIMITED WARRANTY IS ILLEGAL OR UNENFORCEABLE BY REASON OF
ANY LAW, SUCH PARTIAL ILLEGALITY OR UNENFORCEABILTY SHALL NOT
AFFECT THE ENFORCEABILITY OF THE REMAINDER OF THIS LIMITED
WARRANTY WHICH PURCHASER ACKNOWLEDGES IS AND WILL ALWAYS BE
CONSTRUED TO BE LIMITED BY ITS TERMS OR AS LIMITED AS THE LAW PERMITS.
This Limited Warranty allocates risk of product failure between purchaser and ION Audio, and
ION Audio's product pricing reflects this allocation of risk and the limitations of liability
contained in this Limited Warranty. The agents, employees, distributors, and dealers of ION
Audio are not authorized to make modifications to this Limited Warranty, or make additional
warranties binding on ION Audio or inMusic. Accordingly, additional statements such as
dealer advertising or presentation, whether oral or written, do not constitute warranties by
ION Audio or inMusic and should not be relied upon. Some jurisdictions do not allow
limitations on how long an implied warranty lasts, so the above limitation may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights which
vary under local laws.
Please record the serial number of your unit as shown on the back of the chassis as well as the
name of the dealer from whom you purchased the unit. Retain this information and your
original purchase receipt for your records. Go to our web site ionaudio.com to register your product
with us.
MODEL: PURCHASED FROM:
SERIAL NUMBER: DATE OF PURCHASE:
7

RETURN INF O RMATI O N
• A Return Authorization number must be obtained from your local ION
Audio
Representative. For your representative go to ionaudio.com.
• A copy of the original sales receipt must also be included for the equipment to
be repaired under warranty.
• The faulty equipment must be packed in its original packaging.
• One additional outer layer of packaging must be included to ensure
product safety. Failures to do so may inadequately protect the equipment in
transit and, therefore, jeopardize the customer's warranty.
• ION Audio will not accept C.O.D. shipments and no call tags will be issued for
merchandise return.
• ION Audio will not return repaired merchandise to customers by priority service,
unless by written request at the customer's cost. Requests must be submitted in
writing with merchandise returned.
• The defective ION Audio equipment should be sent, FREIGHT PREPAID with
Return Authorization number clearly printed on the outer packaging and original
sales receipt enclosed to your local service center
8

IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all Instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and a
third grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachment/accessories specified by the manufacturer.
12. Use only the cart, stand, tripod, bracket or table specified by the
manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. Power Sources - This product should be connected to a power supply only of the
type described in these operating instructions, or as marked on the unit.
16. Internal/External Voltage Selectors - Internal or external voltage selector switches, if
any,should only be reset and re-equipped with a proper plug for alternative voltage by a qualified
service technician. Do not attempt to alter this yourself.
17. Water and Moisture - This product should be kept away from direct contact with liquids. The
apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9

18. CAUTION –Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type. Batteries (a battery pack or an installed battery) shall
not be exposes to excessive heat such as sunshine, fire, etc.
19. Where the mains plug or an appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
20. Protective earthing terminal: The apparatus should be connected to a
mains socket outlet with a protective earthing connection.
a. Finland (Suomi): Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan.
b. Norway (Norge): Apparatet må tilkoples jordet stikkontakt.
c. Sweden (Sverige): Apparaten skall anslutas till jordat uttag.
21. This symbol means the equipment is a Class II or double-insulated electrical appliance. It
has been designed in such a way that it does not require a safety connection to electrical
earth.
22. Do not install this equipment in a confined or "boxed-in" space such as a bookcase or similar
unit, and maintain good ventilation conditions. The ventilation should not be impeded
by covering the ventilation openings with items such as newspaper, tablecloths, curtains, etc.
23. This apparatus is for professional use only.
24. When moving or not using the appliance, secure the power cord (e.g., wrap it with a cable
tie). Be careful not to damage the power cord. Before using it again, make sure the power
cord has not been damaged. If the power cord has been damaged at all, bring the unit and
cord to a qualified service technician for repair or replacement as specified by
the manufacturer.
25. WARNING: Excessive sound pressure (high volumes) from headphones can cause hearing
loss.
26. WARNING: Please refer to any important information (e.g., electrical, safety, etc.) printed on
the exterior bottom enclosure or rear panel before installing or operating the product.
SERVICE INS
T RUCTIONS
• Disconnect power cord before servicing.
• Replace critical components only with factory parts or recommended equivalents.
• For AC line powered units –Before returning repaired unit to user, use an ohmmeter to
measure from both AC plug blades to all exposed metal parts. The resistance should
be more than 2,000,000 ohms.
10

SAFETY NO TIC E S
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE ANY COVER . NO USER-
SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
DANGEROUS VOLTAGE: The lightning flash with arrowhead symbol
within the equilateral triangle is intended to alert the user to the presence of
un- insulated "dangerous voltage" within the product's enclosure that may
be of sufficient magnitude to constitute a risk of electric shock.
INSTRUCTIONS: The exclamation point within the equilateral triangle is
intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying this
appliance.
SA 1965
SA 1966
WARNING: To reduce the risk of fire or electrical shock, do not expose this appliance to
rain or moisture. Electrical equipment should NEVER be kept or stored in damp environments.
CAUTION (for U.S.A. & CANADIAN models only): TO PREVENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR
OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
NOTICE CONCERNING LASER PRODUCTS: DANGER: INVISIBLE LASER RADIATION WHEN
OPEN AND INTERLOCK FAILED OR DEFEATED. AVOID DIRECT EXPOSURE TO BEAM. USE
OF CONTROLS OR ADJUSTMENTS OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
NOTICE CONCERNING FCC REGULATIONS: You are cautioned that changes or modifications
not expressly approved by the part responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
11

interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
a) Reorient or relocate the receiving antenna.
b) Move this unit.
c) Increase the separation between the equipment and receiver.
d) Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
e) Be sure that all cables are properly shielded, using a choke or ferrite where appropriate.
f) Consult the dealer or an experienced radio/television technician for help.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE
MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
This device complies with Industry Canada RSS-210. Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
. ESD / EFT Warning: This unit may contain a microcomputer for signal processing
and control functions. In very rare situations, severe interference, noise from an
external source, or static electricity may cause it to lock up. In the unlikely event
that this should happen, turn off the unit, wait at least five seconds, and then turn it
back on again.
In an environment with radio frequency interference, the unit may malfunction and resume normal
operation after removal of the interference.
For best audio quality, avoid using this device in a high RF-radiated environment.
This unit does not exceed the Class B limits for radio noise emission from digital apparatus set out
in the radio interference regulations of the Canadian Department of Communications.
For 240-volt use in U.K., use NEMA-style 240-volt plug. For other countries use proper plug for local
outlet.
12