ION F10 User manual

ION F10 850VA
User Guide
ION F10
User Guide
Power Backup 850VA/490W

ION F10 850VA
User Guide
Contents
ION F10 User Guide
www.ionups.com.au
Important Safety Instrucons _______________________________ 4
Installing your UPS System__________________________________ 5
Basic Operaon ____________________________________________ 8
Technical Specicaons____________________________________ 10
LED Indicator _____________________________________________ 12
Troubleshoong___________________________________________ 13
Soware __________________________________________________ 14

ION F10 850VA
4
Important Safety
Instrucon
The UPS must be connected to a grounded AC power outlet
with fuse or circuit breaker protecon. DO NOT plug the UPS
into an outlet that is not grounded. If you need to de-energize
this equipment, turn o and unplug the UPS.
The baery can energize hazardous live parts inside even
when the AC input power is disconnected.
To prevent the risk of re or electric shock, install in a
temperature and humidity controlled indoor area, free of
conducve contaminants. (Please see specicaons for
acceptable temperature and humidity range).
To reduce the risk of electric shock, do not remove the cover.
There are no user serviceable parts inside.
To avoid electrical shock, turn o the unit and unplug it from
the AC power source before installing a computer component.
Do not use with or near aquariums! To reduce the risk of re,
do not use with or near aquariums. Condensaon from the
aquarium can come in contact with metal electrical contacts
and cause the machine to short out.
Do not use with laser printers! The power demands of laser
printers are too large for a UPS.
This manual contains important instrucons that should
be followed during installaon and maintenance of the
ION F10 UPS and baeries. Please read and follow all
instrucons carefully during installaon and operaon
of the unit. Read this manual thoroughly before
aempng to unpack, install, or operate.

ION F10 850VA
User Guide
5
Installing your
UPS system
The UPS must be connected to a grounded AC power outlet
with fuse or circuit breaker protecon. DO NOT plug the UPS
into an outlet that is not grounded. If you need to de-energize
this equipment, turn o and unplug the UPS.
The baery can energize hazardous live parts inside even
when the AC input power is disconnected.
To prevent the risk of re or electric shock, install in a
temperature and humidity controlled indoor area, free of
conducve contaminants. (Please see specicaons for
acceptable temperature and humidity range).
To reduce the risk of electric shock, do not remove the cover.
There are no user serviceable parts inside.
To avoid electrical shock, turn o the unit and unplug it from
the AC power source before installing a computer component.
Do not use with or near aquariums! To reduce the risk of re,
do not use with or near aquariums. Condensaon from the
aquarium can come in contact with metal electrical contacts
and cause the machine to short out.
Do not use with laser printers! The power demands of laser
printers are too large for a UPS.
The box should contain the following:
UPS Unit
User Manual
UNPACKING
The ION F10 UPS ensures consistent power to your
computer system and its included soware will
automacally save your open les and shutdown your
computer system during a ulity power loss.
OVERVIEW
1. Make sure that the total Volt-Amp (VA) requirements
of your computer, monitor, and peripheral equipment
does not exceed rated capacity of 850VA/490 was.
2. Ensure that the equipment plugged into the baery
power-supplied/surge outlets does not exceed the
UPS unit’s rated capacity. If the rated unit capacies
are exceeded, an overload condion may occur
and cause the UPS unit to shut down or the circuit
breaker to trip.
HOW TO DETERMINE THE
POWER REQUIREMENTS
OF YOUR EQUIPMENT

ION F10 850VA
6
1. Your new ION F10 UPS may be used immediately upon
receipt. However, recharging the baery for at least
8 hours is recommended to ensure that the baery’s
maximum charge capacity is achieved. Charge loss may
occur during shipping and storage. To recharge the
baery, simply leave the unit plugged into an AC outlet.
The unit will charge in both the on and o posion.
2. With the ION F10 UPS unit o and unplugged, connect
the computer, monitor, and any externally powered
data storage device (Zip drive, Jazz drive, Tape drive,
etc.) into the baery power supplied outlets. Do not
plug a laser printer, copier, space heater, vacuum, paper
shredder or other large electrical device into the UPS.
The power demands of these devices will overload and
possibly damage the unit.
3. Plug the ION F10 UPS in a 2 pole, 3 wire grounded
receptacle (wall outlet). Make sure the wall branch
outlet is protected by a fuse or circuit breaker and does
not service equipment with large electrical demands
(e.g. air condioner, refrigerator, copier, etc.) Avoid
using extension cords.
4. Depress the power switch to turn the unit on. The
power on indicator light will illuminate and the unit will
“beep”.
HARDWARE INSTALLATION
GUIDE

ION F10 850VA
User Guide
7
5. If an overload is detected, an audible alarm will sound
and the unit will emit one long beep. To correct this,
turn the UPS o and unplug at least one piece of
equipment from the outlets. Wait 10 seconds. Make
sure the circuit breaker is depressed and then turn the
UPS on.
6. Your UPS is equipped with an auto-charge feature.
When the UPS is plugged into an AC outlet, the baery
will automacally recharge.
7. To maintain opmal baery charge, leave the UPS
plugged into an AC outlet at all mes.
8. To store your UPS for an extended period, cover it and
store with the baery fully charged. Recharge the
baery every three months to ensure baery life.

ION F10 850VA
8
ION F10 850VA
Basic Operaon
Descripon
1. Power On/O Switch.
Press the power switch to turn the UPS ON
or OFF.
2. LED Indicator
The LED Indicator shows using AC, using
baery, and fault. Refer to “LED Indicator”
secon for details.
3. Baery Backup & Surge Protected Outlets
Provide baery backup and surge protecon.
They ensure power is provided to connected
equipment over a period of me during a power
failure.
4. Surge Protected Outlets
Provide surge protecon for aached
equipment.
ION F10 850VA
Descripon

ION F10 850VA
User Guide
9
1
5
7
8
2
3
6
4
5. Input power cord
Connect to ulity power.
6. USB Communicaon Port
This port allows connecon and communicaon
from the USB port on the computer to the UPS
unit.
7. Communicaon Protecon Ports (RJ45&RJ11)
Communicaon protecon ports will protect any
standard modem, fax, telephone line, or network
cable.
8. Input Circuit Breaker
The Circuit Breaker provides opmal overload
protecon.

10
ION F10 850VA
Technical
Specicaons
MODEL F10-850VA
OUTPUT
Output Power Capacity 490W/850VA
Max Congurable Power 490W/850VA
Nominal Voltage (Ba.mode) 220-240Vac
Frequency (Ba.mode) 50/60±1% Hz
Waveform (Ba.mode) Simulated Sinewave
THDv ≤ 3% @ linear load, ≤5%@non-linear load
Transfer Time 4ms typical
Overload Protecon Circuit breaker or inner rmware protecon
INPUT
Nominal Input Voltage 220-240Vac
Voltage Range 180-270Vac
Frequency 50/60Hz (Auto sensing)
INDICATORS
Display LED
Alarm Ba. Mode, low baery, overload, fault, etc.
BATTERY
Baery Voltage 12V
Baery Type 5.6AH
Total Baery Quanty 1
Recharge Time (to 90%) 8H
Charger Current 0.7A

ION F10 850VA
User Guide
11
UPS PHYSICAL
Maximum Height 90mm
Maximum Width 110mm
Maximum Depth 309mm
Net Weight 3kg
COMMUNICATION
USB Yes
RJ 11/45 Yes
MANAGEMENT
Auto Recharge Yes
Auto Restart Ye s
Power Management Soware Yes
ENVIRONMENT
Operaon Temperature 0-40°C
Operaon Humidity 0-90% non-condensing
CONFORMANCE
Approvals CE
Standard Warranty 2 Year Advanced Replacement
MODEL F10-850VA
OUTPUT
Output Power Capacity 490W/850VA
Max Congurable Power 490W/850VA
Nominal Voltage (Ba.mode) 220-240Vac
Frequency (Ba.mode) 50/60±1% Hz
Waveform (Ba.mode) Simulated Sinewave
THDv ≤ 3% @ linear load, ≤5%@non-linear load
Transfer Time 4ms typical
Overload Protecon Circuit breaker or inner rmware protecon
INPUT
Nominal Input Voltage 220-240Vac
Voltage Range 180-270Vac
Frequency 50/60Hz (Auto sensing)
INDICATORS
Display LED
Alarm Ba. Mode, low baery, overload, fault, etc.
BATTERY
Baery Voltage 12V
Baery Type 5.6AH
Total Baery Quanty 1
Recharge Time (to 90%) 8H
Charger Current 0.7A

12
ION F10 850VA
LED
Indicator
LED ALARM CONDITION
On O Normal
Flash Beep 1 me In
Every 30 Seconds
Ulity Failure - The UPS is providing
baery power to outlets.
Flash Beep 1 me In
Every 2 Seconds
Ulity Failure - The UPS is providing
baery power. The rapid beeps
indicate the baery will run out of
power shortly.
On/Flash Beep 1 me In
Every 0.5 Second
Overload - Occurs when connected
equipment exceeds the rang of the
unit. Turn the UPS o and unplug at
least one piece of equipment from
the UPS.

ION F10 850VA
User Guide
13
LED ALARM CONDITION
On O Normal
Flash Beep 1 me In
Every 30 Seconds
Ulity Failure - The UPS is providing
baery power to outlets.
Flash Beep 1 me In
Every 2 Seconds
Ulity Failure - The UPS is providing
baery power. The rapid beeps
indicate the baery will run out of
power shortly.
On/Flash Beep 1 me In
Every 0.5 Second
Overload - Occurs when connected
equipment exceeds the rang of the
unit. Turn the UPS o and unplug at
least one piece of equipment from
the UPS.
Troubleshoong
PROBLEM POSSIBLE CAUSE SOLUTION
The outlets stop
providing power to
equipment. Circuit
breaker buon is
projecng from the
side of the unit.
Circuit breaker has
tripped due to an
overload.
Turn the UPS o and
unplug at least one piece
of equipment. Reset
the circuit breaker by
depressing the buon, and
then turn the UPS on.
The UPS does not
perform expected
runme.
Baery not fully
charged.
Recharge the baery by
leaving the UPS
plugged in.
Baery is slightly worn
out.
Contact Technical Support.
The UPS will not
turn on
The on/o switch is
designed to prevent
damage by rapidly
turning it o and on.
Turn the UPS o. Wait 10
seconds and then turn the
UPS on.
The baery is worn out. Contact Technical Support.
Mechanical problem Contact Technical Support.

ION F10 850VA
14
Soware Download
INSTALLATION PROCEDURE:
Power Master management soware provides a user-friendly
interface for your power systems. The graphic user-interface is
intuive and displays essenal power informaon at a glance.
Please follow procedure below to install the soware.
Power Master
System
Summary
UPS
Status
Information
Conguration
Diagnostics
Load
Input
Status
Voltage
Frequency
Normal
229.9V
49.90Hz
Event Action
Events
Recipient
Settings
Logs
Events Logs
Status Records
Settings
Schedule
Shutdown
Output
Status
Voltage
Frequency
Load
Normal / Eco Mode
230.0V
49.90Hz
0% (0 Watts)
Battery
Status
Capacity
Normal /Charging
46%
UPS Status
1. D o w n l o a d P o w e r M a s t e r f r o m t h e w e b s i t e :
hp://www.powermonitor.soware/
2. Double-click the le and follow the
installaon steps. When your computer
restarts, the Power Master soware will
appear as a blue icon located in the system
tray.
Pb Pb
All rights reserved. Reproducon without permission is prohibited.

ION F10 850VA
User Guide
15

[email protected]
www.ionups.com.au
P: 1300 700 805