IPGARD SDHN-4D-P User manual

DESIGNED
AND MADE
IN THE USA
NOTICE
The information contained in this document is
subject to change without notice. iPGARD makes
no warranty of any kind with regard to this material,
including but not limited to, implied warranties of
merchantability and tness for particular purpose.
iPGARD will not be liable for errors contained herein
or for incidental or consequential damages in
connection with the furnishing, performance or use
of this material. No part of this document may be
photocopied, reproduced, or translated into another
language without prior written consent from
iPGARD, Inc.
20170523
SDHN-4D-P
Secure KVM Switch
Advanced 4-Port Secure
Dual-head DisplayPort to
HDMI KVM Switch with
Audio and CAC Support
Quick Start Guide
A full Manual can be downloaded from
www.ipgard.com/documentation/
TECHNICAL SPECIFICATIONS WHAT’S IN THE BOX
VIDEO
Format DisplayPort/HDMI
Host Interface (8) DisplayPort 20-pin (female)
User Console
Interface (2) HDMI 19-pin (female)
Max Resolution 3840x2160 @ 30Hz
DDC 5 volts p-p (TTL)
Input Equalization Automatic
Input Cable Length Up to 20 ft.
Output Cable Length Up to 20 ft.
USB
Signal Type
USB 1.1 and 1.0 Keyboard and
Mouse only.
USB 2.0 for CAC connection.
USB Type B Inputs (4) Keyboard-Mouse; (4) CAC
User Console
Output Interface
(2) USB Type-A for keyboard
and mouse connection only.
(1) USB Type-A for CAC
connection.
AUDIO
Input (4) Connector Stereo 3.5mm
Female
Output (1) Connector Stereo 3.5mm
Female
POWER
Power Requirements 12V DC, 2A power adapter with
center-pin positive polarity
ENVIRONMENT
Operating Temp 32° to 104° F (0° to 40° C)
Storage Temp -4° to 140° F (-20° to 60° C)
Humidity 0-80% RH, non-condensing
CERTIFICATIONS
Security Accreditation
Common Criteria Validated To
NIAP, Protection Prole PSS
Ver. 3.0
OTHER
Emulation USB 1.1 and USB 2.0
Compatible
Control Front Panel Buttons
PART NO. QTY DESCRIPTION
SDHN-4D-P 14-port, Secure DH DisplayPort
to HDMI KVM Switch
PS12VDC2A 112V DC, 2A power adapter with
center-pin positive polarity.
1Quick Start Guide
Toll Free: [phone]
Phone: [phone]
Fax: [phone]
3291 N. Jones Blvd.,
Las Vegas, NV 89108
iPGARD.COM

DESIGNED
AND MADE
IN THE USA
SDHN-4D-P
DP IN
AUDIO OUT
HDMI OUT
USB IN
USB OUT
CAC IN
CAC OUT
AUDIO IN
1 2 3 4
SDHN-4D-P
EDID LEARN HARDWARE INSTALLATION
A full Manual can be downloaded from
www.ipgard.com/documentation/
The KVM is designed to learn the connected
monitor’s EDID upon power up. In the event
of connecting a new monitor to the KVM, a
power recycle is required.
The KVM will indicate to the user the EDID
learn process by ashing the front panel’s
LEDs. Port one green and push button blue
LEDs will both begin to ash for about 10
seconds. When the LEDs stop ashing, the
EDID learn process is done.
If the KVM has more than one video board
(such as dual-head and quad-head models),
then the unit will continue to learn the EDIDs
of the connected monitors and indicate the
progress of the process by ashing the next
port selection green and push button blue
LEDs respectively.
The monitor must be connected to the video
output connector located in the console
space at the back of the KVM during the
EDID learn process.
If the read EDID from the connected monitor
is identical to the current stored EDID in the
KVM then the EDID learn function will be
skipped.
1. Ensure that power is turned off or disconnected from the unit and the computers.
2. Use a DisplayPort cable to connect the DisplayPort output port from each computer to the
corresponding DisplayPort IN ports of the unit.
3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the
respective USB ports of the unit.
4. Optionally connect a stereo audio cable (3.5mm to 3.5mm) to connect the audio output of
the computers to the AUDIO IN ports of the unit.
5. Connect the monitors to the HDMI OUT console ports of the unit using HDMI cables.
6. Connect a USB keyboard and mouse to the two USB console ports.
7. Optionally connect stereo speakers to the AUDIO OUT port of the unit.
8. Optionally connect CAC (COMMON ACCESS CARD, SMART CARD READER) to the CAC port
in the user console interface.
9. Power on the KVM by connecting a 12VDC power supply to the power connector, and then
turn on all the computers.
Note: The computer connected to port 1 will always be selected by default after power up.
Note: You can connect up to 4 computers to the 4 port KVM.
A full Manual can be downloaded from
www.ipgard.com/documentation/