IPSPRO IPS User manual

BASIC PACK IPSPRO - USER MANUAL
**** READ THIS ENTIREGUIDE BEFORE USING THIS P R O D U CT ****

IPS Pro WARRANTY I N F O R M A TI O N
IPSPRO warrantees this product to the original purchaser for One Year for manufacturing
defects due to faulty components or workmanship for One year from the date of purchase for
Registered users. This warranty does not cover part failure due to non-compliance with
operating instructions, normal wear, or tool abuse resulting in cracked, broken or damaged
components. Deficient parts or units will be replaced or repaired based on IPSPROS’s
discretion. For replacement parts, or warranty repairs, contact one of our Authorized Repair
Facilities listed below, or a IPSPRO vendor on our website at ipspro.com. Return freight,
packing and insurance costs, if any, will be paid by the owner. This warranty gives you
specific legal rights, and you may also have other rights, which vary from state to state.
IPS PRO CUSTOMER SERVICE:
MARYLAND
16620 Oakmont Avenue, Gaithersburg, MD 20877
Email: [e-mail]
*******
IPS PRO LLC OFFICE:
FLORIDA
1145 Via Jardin, West Palm Beach, FL 33418
Email: [e-mail]

The manufacturer warranty will be voided if the following procedures are not followed. You
must register your sprayer by using one of the methods below. During use, always use one
of the provided filters to prevent debris from clogging the pump. After every use, rinse out
the sprayer and tips by spraying 1 gallon of water (approximately 2 minutes) through the
pump to rinse any residual products from the unit to prevent corrosion or clogs, then remove
the battery. If used for applying sealers, deck stains and other coating products, always rinse
the gun using a Sodium Hydroxide based deck stain stripping product. DO NOT USE
MINERAL SPIRITS OR PAINT THINNERS.
Chemical Compatibility:
This product can NOT be used with Sodium Hypochlorite over 10% in strength, or chemicals
that contain solvents, non-water based diluents, Acetone, Xylene, Acids, paint removers or
similar products.
IPS Pro WARRANTY REGISTRATION
To register your IPSPRO gun for Warranty, fill out the form below and mail it with a
copy of your Receipt to: IPSPRO 1145 Via Jardin, West Palm Beach, FL 33418
Or register online on: www.ipspro.us

SAFETY WARNING
Stay alert and vigilant, be focused on the work you are doing and be cautious of your
surroundings while using this device. Do not use when you are tired or under the influence of
alcohol, drugs, or medications. Use safety gloves, protective masks, and protective glasses.
Battery Safety: Only use the batteries and charger provided with the tool. When batteries
are not being used, keep them away from any metal objects like paper clips, coins, keys,
nails, or screws. Keep the battery charger, batteries and gun motor dry at all times to avoid
damage or electrical shock. When damaged, liquid can leak from the battery, avoid contact
with the substance. In the case of an accidental contact, clean with water. If the fluid gets into
your eyes immediately rinse with water and seek medical assistance.
Using The IPSPRO Spraying System:
Step 1: Unpack the sprayer and make sure the kit is complete.
Step 2: Charge the battery by following the directions on the battery chargers label. Always
fully charge the battery 1.2 AH before the first use. The initial charge of the battery 1.2 AH
can take longer than 4 hours.
Step 3: Insert the battery into the bottom of the sprayer by gently sliding it in until you hear a
«click». To remove the battery, press and hold the button on the battery and gently pull the
battery off.
Step 4: Insert the hose on the bottom of the sprayer. Next, insert the filter on the opposite
end of the hose and place filter into your container. To use the sprayer with a bottle. Use the
small hose and attach bottle to the bottom of gun.
NOTE: ALWAYS USE A FILTER, and when working at heights, start the device on ground
level to prime the pump.
IPSPRO accessories available on www.ipspro.us

OPERATING TIPS FOR THE IPSPRO SPRAYING SYSTEM
Cleaning the Nozzles: Use the nozzle disassembly key counter clockwise to remove the
green nozzle holder from inside the tip.
NOTE: USING THE IPSPRO WITH THICKER FLUIDS IS EASIER WITH THE IPSPRO
WOOD PRO KIT AVAILABLE ON WWW.IPSPRO.US
If used for applying sealers, deck stains and other coating products, always rinse the gun
using a Sodium Hydroxide based deck stain stripping product. DO NOT USE MINERAL
SPIRITS OR PAINT THINNERS.
TROUBLESHOOTING:
NOTE: Gun does not pull chemicals through the hose
Usually this is caused by debris entering the pump, using the sprayer with a chemical that it’s
not designed for, or if the pump is not completely rinsed out after the last use.
To try to solve this problem easily, hook up your hose to your gun, then insert the other end
of your hose into a garden hose, or sink faucet, to “PUSH” water to the pump, while running
the sprayer for a few minutes. Usually this will flush out any debris and the gun will start
working normally again. If this does not solve the problem, then you can always replace the
seals or rebuild the pump in about 15 Minutes yourself, or you can mail it to one of our
Authorized Repair Facilities for an estimate.
If you dropped your gun or drove over it with your car, Don’t Worry, Repairing the IPSPRO is
an easy 10-15 Minute job, and you only need a Phillips Screwdriver, and Allen Wrench to do
it!
FREQUENTLY ASKED QUESTIONS
Are there any products that the IPSPRO Sprayer Can NOT be used with?
Using products with Solvents that are commonly used in Graffiti Removers, Mineral Spirits,
Paint Thinners, NAPTHA or similar chemicals will damage the sprayer.
Can the IPSPRO Spray be used to apply deck stains and sealants?
The sprayer can be used to apply any clear deck sealant, and when used with the “Wood
Pro” kit, it can apply Ready Seal, Armstrong Clark Semi Transparent, Bakers Gray Away,
TWP, BEHR and other deck thicker deck stains.
NOTE: After using the sprayer with deck sealers and stains, clean the gun by spraying a
deck stain remover through it, then run a gallon of fresh water through it. Failure to rinse the
sprayer out properly will cause the seals to stick and it will not operate properly until it has
been cleaned out or the seals have been replaced in the pump.
Can the sprayer be used for applying Janitorial Cleaners?
Yes, the IPS Sprayers have been used to apply Mildecides, Quaternary, Deodorizers, De-
greasers, Disinfectants, floor strippers, tile and grout cleaners, shower stall cleaners, Simple
Green, Windex, Oven Cleaners, Murphy’s Oil Soap, Bleach and other similar products.
Can the sprayer be used for applying Pest Control Products?
Yes, the IPSPRO Sprayers have been used to apply Insecticides, Pesticides for Ants, Fleas,
Mosquitos and other insects, as well as repellents for Snakes, Deer, Rabbits and other
animals.
How do I remove the hose from the handle, it seems very tight?
If you prefer, you can remove the hose after each use or leave it on the gun. If the hose is
hard to remove, try twisting it, sometimes that will break the seal a little easier so that you
can pull it off. If it’s still difficult to remove, or if the hose doesn’t “seal” as well on the hose
barb, use a razor blade and cut a small slit in the side of the hose to remove it, then cut off
ne inch of hose to remove the stretched area of hose from the line.

IPS BASIC PACK includes:
- 1 Sprayer IPS
- Single Battery 1.2 AH (NiZn)
- Single Charger 1.2 AH (4hrs of charge)
- 2 Nozzles (mist jet + flood jet) + straight connector/nut + disassembly key
- 1 Special concentrated jet nozzle
- Extension hose of 21.6 inches, made of fiberglass + nut
- Suction hose + 13.1 feet PVC hose + suction strainer
- Suction hose + 11.8 inches PVC hose for soda bottles
- A4 format user's manual
- Package made of cardboard