iRay Technology Mars1417XF User manual

iRay Technology Co. Ltd. 1
Digital Flat Panel Detector
Mars1417XF
User Manual
Before operating, please read this user manual and pay attention to all safety precautions. Please
ensure that user manual is properly maintained so that it can be accessed at any time. Please use
correctly on the basis of full understanding of content.

To Customers
iRay Technology Co. Ltd. 2
To Customers
Congratulations on your purchase of Mars1417XF wireless digital flat panel
(hereinafter referred to as Mars1417XF) which is manufactured by iRay Technology
Co. Ltd. (Hereinafter referred to as iRay).
At iRay, we strive to not only make the world-class product that delivers the best
value to our customers but also offer the highest quality of service and customer
care. Please take time to read user guide in order to utilize product effectively. We
hope you enjoy experience with Mars1417XF.
If you have any questions or suggestions, please feel free to contact us.
About FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference;
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Attention that changes or modification not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this product does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
Service Office
Tel: [phone]
Fax: [phone]
E-mail: [e-mail]
Location: 2F, Building 9, No.590, Ruiqing Rd, Pudong, Shanghai,
China PC: 201201

To Customers
iRay Technology Co. Ltd. 3
About SAR
After the laboratory measurement, the max SAR value is 0.058mW/g for 2.4GWLAN and max
SAR value is 0.277mW/g for 5G WLAN which satisfies the RF exposure requirement.
Notes on usage and management of equipment
1. Read all instruction in user guide before operation. Pay attention to all safety
precautions.
2. Only a physician or a legally certified operator should use this product.
3. The equipment should be maintained in safe and operable condition by
maintenance person.
4. Use only computers and image display monitors complying with IEC 60601-1 or
IEC 60950-1. For details, consult our sales representative or local iRay dealer.
5. Use dedicated cables. Do not use cables other than those supplied with product.
6. Do not open cover of product without authority.
7. Request your sales representative or local iRay dealer to install this product.
Caring for your environment
This symbol indicates that product cannot be disposed of with your residential or
commercial waste.
Recycling iRay Equipment
Please do not dispose of this product with your residential or commercial waste.
Improper handling of this type of waste would produce a negative impact on health
and environment. Some countries or regions, such as European Union, has set up
systems to collect and recycle electrical or electronic waste items. Contact your
local authorities for information about practices established in your region. If
collection systems are not available, call iRay Customer Service for assistance.
Disclaimer
•iRay shall not be liable to any damage, loss, or injury incurred to purchaser
and the third parties as a result of fire, earthquake, any accident, misuse or
abuse of product.
•iRay shall not be liable to any damage, loss, or injury arising from unauthorized
modifications, repairs, or alterations or failure to strictly comply with iRay’s
operation and maintenance instruction.

To Customers
iRay Technology Co. Ltd. 4
•iRay shall not be liable to any damage or loss arising from use of any option or
consumer goods other than those dedicated as Original iRay product.
•It is the responsibilities of users and physicians for maintaining the privacy of
image data and providing medical care service. iRay shall not be responsible
for legality of image processing, reading and storage nor shall it be responsible
for loss of image data for any reason.
•Information regarding specification, components, and appearance of product is
subject to change without prior notice.。
Copyright
All rights reserved
No part of this publication may be reproduced in any form or by any means without
the written permission of iRay. The information included is designed only for use
with Mars1417XF.
Trademarks
The iRay name and iRay logo are registered trademarks of iRay Technology Co.
Ltd.
Symbols and Conventions
The following symbols and conventions are used throughout user guide.
This symbol is used to identify condition under
which improper use of product may cause death or
serious human injury.
This notice is used to identify condition under
which improper use of product may cause minor
human injury.
This notice is used to identify condition under
which improper use of product may cause property
damage.
This is used to indicate a prohibited operation.
This is used to indicate an action that must be
performed.

To Customers
iRay Technology Co. Ltd. 5
This is used to indicate important operation and
restriction.
This is used to indicate operation for reference and
complementary information.
Labels and markings on the equipment
The labels and markings on Mars1417XF product are indicated below:
Marking Description
Caution: please refer to instruction in user manual.
This symbol is used to indicate that equipment has passed
CE testing and it is followed by CE number.
This symbol is used to identify manufacture series number
which is after, below or adjacent to symbol. The series
number of iRay product is usually made of thirteen digits as
shown below:
This symbol is used to indicate name and address of
manufacturer.
This symbol is used to indicate name and address of iRay
authorized representative in European region.
This symbol is used to indicate consultation of user guide for
general information.
Numerical Order
Year
Date
Month
Version
Product Code
A1A2A3A4 C1C2 M DD Y XXX

To Customers
iRay Technology Co. Ltd. 6
Safety Signs: please refer to user guide for safety
instructions.
Safety Signs：Dangerous Voltage.
Stand-by.
Handle with care.
FPD is allowed to withstand 100kg on surface
This symbol is used to indicate operation temperature range.
This symbol is used to indicate storage temperature range.
Non-ionizing radiation
FCC Federal Communications Commission certificate
Package symbol: fragile.
Package symbol: keep away from sunlight.
Package symbol: keep dry.

To Customers
iRay Technology Co. Ltd. 7
Package symbol: this symbol is used to indicate humidity
range.
Package symbol: keep equipment up right.
Package symbol: do not roll package.
Package symbol: this symbol is used to indicate stacking limit
number.
Detector symbol: the device passes IPX4 test

Contents
iRay Technology Co. Ltd. 8
Contents
1Safety Information ......................................................................................................................11
1.1 Safety precautions 11
1.2 Notes for Using 15
2General Description ....................................................................................................................17
2.1 Scope 17
2.2 Model 17
2.3 Characteristic 18
2.4 Intended use 18
2.5 Product Components 18
2.6 Components Description 20
2.6.1 Detector ...............................................................................20
2.6.2 Battery Pack ........................................................................21
2.6.3 Battery Charger ...................................................................22
2.7 Product Specification 23
2.7.1 Detector ...............................................................................23
2.7.2 Battery .................................................................................25
2.7.3 Battery Charger ...................................................................26
2.7.4 SDK Recommended Condition...........................................26
2.7.5 Environment ........................................................................27
3Installation ..................................................................................................................................28
3.1 Detector Install 28
3.1.1 Attach Battery Pack.............................................................28
3.1.2 Booting Up ..........................................................................28
3.1.3 Adapter ................................................................................31
3.2 Software Installation 31
3.3 Detector Installation 31
3.3.1 Configuration of External wireless AP................................32
3.3.2 Wireless configuration of detector (if necessary) ................36

Contents
iRay Technology Co. Ltd. 9
3.3.3 Wireless configuration reset ................................................37
4Operation ....................................................................................................................................40
4.1 Main Operation 40
4.1.1 Software Mode ....................................................................40
4.1.2 AED Mode ..........................................................................42
4.2 Connection Build 44
4.3 Panel Configuration 45
4.4 Correction Template Generation 46
4.4.1 Pre-offset Template Generation...........................................47
4.4.2 Gain Template Generation...................................................48
4.4.3 Defect Template Generation................................................51
4.5 Image Check and upload 53
4.5.1 Local Image Check..............................................................54
4.5.2 Panel Image Upload ............................................................54
4.5.3 Defect Template Check and Modification...........................56
4.6 Correction Template Management 58
4.6.1 Template Synchronization...................................................58
4.6.2 Correction Activation ..........................................................62
4.7 Firmware Update 64
4.8 Short cut 67
4.9 Software 67
4.9.1 Main GUI ............................................................................67
4.9.2 Home Page ..........................................................................68
4.9.3 Acquire Page .......................................................................68
4.9.4 SDK Page............................................................................71
4.9.5 Detector Page ......................................................................72
4.9.6 Calibrate Page .....................................................................77
4.9.7 Local File Page....................................................................77
4.10 IT-network 78

Contents
iRay Technology Co. Ltd. 10
4.10.1 Purpose for IT-network........................................................78
4.10.2 Required characteristics ......................................................78
4.10.3 Required configuration........................................................78
4.10.4 Technical specifications ......................................................78
4.10.5 Intended information flow...................................................79
4.10.6 hazardous situations resulting from failure of the IT-network
79
4.10.7 Warning ...............................................................................79
4.10.8 Changes to IT-network include: ..........................................80
5Charger Installation.....................................................................................................................81
6Regulatory Information...............................................................................................................82
6.1 Information of Registration 82
6.2 Information of Manufactures 82
6.3 Medical equipment safety standards 82
6.4 Guidance and manufacture’s declaration for EMC 84
6.4.1 EMI Compliance Table........................................................84
6.4.2 EMS Compliance Table.......................................................84
6.5 Radio Frequency Compliance Information 87
6.6 Battery Safety Standards 87
6.7 Product Label 87
7Trouble shooting .........................................................................................................................92
8Product Maintenance ..................................................................................................................93
8.1 Regular inspection and Maintenance 93
8.2 Repairment 93
8.3 Replacement support 93

Safety Information
iRay Technology Co. Ltd. 11
1Safety Information
1.1 Safety precautions
Follow these safe guides and properly use device to prevent injury and damage.
WARNING
Installation and environment
of use
Do not use or store device near flammable chemical such as
alcohol, thinner, benzene, etc.
If chemical is spilled or evaporated, it may result in fire or electric
shock through contact with electric parts inside device. Also,
some disinfectant is flammable. Be sure to take care when using
them.
Do not connect device with anything other than specified.
Doing so may result in fire or electric shock.
All patients with active implantablemedical devices should be
kept awayfrom device.
Power supply
Do not operate using anytype of powersupply other than
indicated on rated label.
Otherwise, it may result in fire or electric shock.
Do not handle with wet hands.
You may experience electric shock that could result in death or
serious injury.
Do not place heavyobject such as medical equipment on cables
and cords. Do not pull, bend, bundle, or step onthem to prevent
sheath from being damaged, and do not alter them neither.
Doing so may damage cords which could result in fire or electric
shock.
Do not supply power tomorethan one piece of equipment using
the same AC outlet.
Doing so may result in fire or electric shock.
Do not turn onsystem power when condensation has formed on
the devie.
Doing so may result in fire or electric shock.
Do not connect multiple portable socket-outlets or extension
cords to system.
Doing so may result in fire or electric shock.
To avoid the risk of electric shock, the devicemust be
connected to power supply with protective earth.
Not doing so may result in fire or electric shock.

Safety Information
iRay Technology Co. Ltd. 12
Securely plug power cord into ACoutlet.
If contact failure occurs or metal objects contact with exposed
metal prongs of plug, may result fire or electric shock.
Be sure to turn off powerto each piece of device before
connecting ordisconnectingcords.
Otherwise, you may get electric shock that could result in death
or serious injury.
Be sure to hold plug orconnector to disconnect cord.
If you pull cords, the core wire may be damaged, resulting in fire
or electric shock.
WARNING
Handling
Never disassemble or modifydevice. No modification is allowed.
Doing so may result in fire or electric shock. Also, since device
contains components that may cause electric shock and other
hazardous parts, touching them may cause death or serious
injury.
Do not place anything on top of device.
The object may fall and cause an injury. Also, if metal objects
such as needles or clips fall inside, it may result in fire or electric
shock.
Do not hit or drop device.
The device may be damaged if receiving a strong jolt, which may
result in fire or electric shock if the device is used without
repairing.
Do not put device and pointed objects together.
It may be damaged. Device is recommended to be used in
Bucky.
Have the patient take a fixed posture and do not let patient touch
unnecessaryparts.
If patients touch connectors or switches, it may result in electric
shock or malfunction.
When problem occurs
Shouldanyof the following occurs, immediatelyunplug the
power cord, and contact sales representative or local iRay
dealer:
When there is smoke, odd smell or abnormal sound.
When liquid has been spilled inside or metal object has entered
through an opening.
When the device has been dropped and damaged.
Maintenance and inspection
Please turn off the powerof device and unplug power cordof
adaptor before cleaning.
Never use alcohol, ether andother flammablecleaningagent for
safety. Never use methanol, benzene, acid andbase because
they will erode device.
Don’t dip the device into liquid.
Please make sure that the device’s surface & plug is dry before
turning on.
Otherwise, it may result in fire or electric shock.
Cleantheplug of power cord periodically by unplugging itfrom
AC outlet and removing dust or dirt from plug, itsperipheryand
AC outlet withdrycloth.

Safety Information
iRay Technology Co. Ltd. 13
If cord is kept plugged in for a long time in a dusty, humid or
sooty place, dust around the plug will attract moisture; this could
cause insulation failure that may result in fire.
For safetyreasons, be sureto turn off power to each piece of
device when performing inspections indicated in thismanual.
Otherwise, electric shock may occur.
CAUTION
Installation and environment
of use
Do not install device in anyof locationslistedbelow. Doing so
mayresultin failure, malfunction, falling, fire or injury.
Close to facilities where water is used
Where it will be exposed to sunlight directly
Close to air outlet of air-conditioner or ventilation equipment
Close to heat source such as heater
Where power supply is unstable
In dusty environment
In saline or sulfurous environment
Where temperature or humidity is high
Where there is freezing or condensation
In areas prone to vibration
On incline or unstable area
Take carethat cables donot becometangled during use. Also,
be carefulnot toget your feet caught by cable.
Otherwise, it may cause malfunction of device or injury of user
due to tripping over cable.
Non-medical equipment such as batterycharger and access
point cannot be used in patient’s vicinity.
Power supply
Always connect three-core power cordplug to grounded AC
power outlet.
To make it easy todisconnect plug at any time, avoid putting
any obstacles near outlet. Otherwise, it maybe impossible to
disconnect plugin emergency.
Be sure to ground device to indoor grounded connector. Also,
be suretoconnect all ground of system together.
Do not use any powersource otherthan provided.
Otherwise, fire or electric shock may be caused due to leakage.
Handling Do not spill liquid or chemicals onto device. In case the patient
isinjured, itiis notallowed to contact withbloodor other body
fluids.
Doing so may result in fire or electric shock.
In such situation, protect device with a disposable cover as
necessary.
Turn off power and pull out plugto each piece of for safety when
notused.
CAUTION

Safety Information
iRay Technology Co. Ltd. 14
Handling Handlecarefully.
Do not submerge devicein water.
The internal image sensor may be damaged if something hits
againstit or dropped. If itis dropped, shock label inside would
turnredand device would not be warranted by iRay.
Do not place excessive weight on device.
Otherwise, internal image sensor may be damaged and image
may be incorrect
Uniform load：150 kg over the whole area of the detector
surface
Local load：100 kg on an area 4 cm diameter
Be sure to use the equipment on flat surface so it will not bend.
Otherwise, the internal image sensor may be damaged.
Be sure to securely hold detector while using it in upright
positions. Otherwise, the detector may fall over, resulting in injury
to user or patient, or may flip over, resulting in damage to device.

Safety Information
iRay Technology Co. Ltd. 15
Keep the same load (the same pressure) on detector when
acquiring image. Or image will be incorrect.
CAUTION
Do not close to fire, do not use in high temperature
Do not invert positive and negative pole
Do not contact with metal in case of short circuit
Do not insert sharp objects into battery
Do not beat battery
Do not stand on battery
Do not use battery out of rules
Do not dispose battery or change internal structure
Do not submerge battery in water, please keep dry in storage
and do not contact with water in use
Please charge battery with charger provided by iRay
Do not mix battery with ones not provided by iRay
Do not charge battery with broken charger.
Charge battery regularly to avoid over discharge failure.
Do not use battery when it is severe ballooning.
1.2 Notes for Using
When using device, take the following precautions. Otherwise, problems may occur and there
would be malfunction.
Before exposure
Be sure to check device daily and confirm that it works properly.
Be sure there is battery installed on Mars1417XF to avoid power off suddenly
Sudden heating of room in cold areas will cause condensation to form on device.
In this case, wait until condensation evaporates before performing an exposure.
If it is used while condensation is formed, problems may occur in the quality of
captured images. When air-conditioner is used, be sure to raise/lower the
temperature slowly so that difference of temperature in room and device does
not occur, to prevent condensation.
The detector should be warmed more than 20 minutes before exposure or
updating gain or defect template.

Safety Information
iRay Technology Co. Ltd. 16
During exposure
Do not move power cable during exposure, or it may cause image noise or
artifacts, even incorrect images.
Do not use equipment near detector generating strong magnetic field. Otherwise,
it may cause image noise, artifacts or even incorrect images.
Do not exposure in 60s after 4 times of full range exposure. Otherwise, image
would be incorrect. Neither do exposure in 30s after a full range exposure. The
larger dose using, the longer time should be waited before next exposure.
During image acquisition, Mars1417XF should not be influenced by physical or
electrical way.
If detector receives dose which is close to full range, clipping data lines appear in
full range area.
After exposure
If detector would not be used in 5 days, it is required to take out battery. If battery
would not be used at long time, it must be charged to 30%~50% every 3 month
or 50%~70% every 6 month.
Disinfection and Cleaning
After every examination, wipe patient contact surfaces with disinfectants such as
ethanol, to prevent the risk of infection. For details on how to sterilize, consult a
specialist.
Do not spray detector directly with disinfectants or detergents.
Wipe it with cloth slightly damped with neutral detergent. Do not use solvents
such as alcohol, thinner, benzene, acid and base. Doing so may damage surface
of detector.
It's recommended to use waterproof non-woven cover as isolated layer between
detector and blooding patient.

General Description
iRay Technology Co. Ltd. 17
2General Description
Mars1417XF is a cassette-size wireless X-ray flat panel detector based on amorphous silicon
thin-film transistor technologies. It is developed to provide the highest quality of radiographic
image, which contains an active matrix of 2336×2836 with 150um pixel pitch. Detectors’
scintillator has two options which are GOS (Gadolinium Sulfoxylate) and CsI (CaesiumIodide).
However, the greatest improvement is wireless communication between detectors and PC.
Meanwhile it can be powered with battery for portable panel use.
2.1 Scope
This manual contains information about Mars1417XF. All operators must read and understand
this manual before using. All information in this manual, including illustrations, is based on
equipment prototype. If your configuration does not have any of these items, information about
these items in the manual does not apply to your detector.
Mars1417XF
Share Mars1417XF for different Radiography modality like an IP plate
2.2 Model
Mars □ □- □
GSI: GOS; CSI: CSI
XF
1417: 14-inch X 17-inch
Mars series

General Description
iRay Technology Co. Ltd. 18
2.3 Characteristic
Wireless static Flat Panel Detector used for general radiography.
14 × 17 inch
AED trigger
Easy to change cable and charge in tray.
Battery recycling
IPX4
2.4 Intended use
Mars1417XF Wireless Digital Flat Panel Detectoris indicated for digitalimaging solution designed
for providing general radiographic diagnosis of human anatomy. It is intended to replace
radiographic film/screen systems in all general purpose diagnostic procedures. This device is not
intended for mammography or dental applications.
The detector could be used for general X ray diagnosis of usual body part. It is not intended for
mammography, dental applications, neonatal and fluoroscopy. More care should be taken when
diagnosis with allergic constitution. Not only this but also prohibited for pregnant women and
children. Shield of none inspection body part is necessary during x ray exposure. There is no
contraindication.
According to Mars1417XF intended use and result of risk management, essential performance is
identified and described as following:
To acquire dark image, Mars1417XF shall be not influenced to imaging acquisition.
To maintain data transmission, Mars1417XF shall be not influenced to data and signal
transmission.
2.5 Product Components
Mars1417XF is configured with components bellowing
Item Description

General Description
iRay Technology Co. Ltd. 19
Mars1417XF Detector Mars1417XF GSI/CSI
Medical adapter for
detector and battery
Charger
24V (DC) power adapter
Battery Pack
7.6V battery pack
Gigabit Ethernet cable
Ethernet cable for
wireless router
AC Power Cable AC Cable for adapter

General Description
iRay Technology Co. Ltd. 20
Battery Charger Battery charger
Note: Mars1417XF package may be different based on requirement.
2.6 Components Description
2.6.1 Detector
External Signals Input and Control Panel
Control Panel
NO. Item Description
ADC Input Interface 24V DC input
BReserved Reserved
CStatus Indicator Detector Status indicator