iRay Technology Mars1717XF Series User manual

iRay Technology Co. Ltd. 1
Digital Flat Panel Detector
Mars1717XF
User Manual
Before operating, please read this user manual and pay attention to all safety precautions. Please
ensure that the user manual is properly maintained so that it can be accessed at any time. Please use
correctly on the basis of full understanding of the content.

To Customers
iRay Technology Co. Ltd. 2
About FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device must not cause harmful interference;
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Attention must be paid to the fact that changes or modifications not expressly approved by the
party responsible for compliance can void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this product does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC exposure limits set forth for an uncontrolled environment.
Sterilization and Shelf Life
This does not apply.
Notes on usage and management of equipment
1. Read all instructions in the user guide before operation. Pay attention to all safety
precautions.
2. Only a physician or a legally certified operator should use this product.
3. The equipment should be maintained in a safe and operable condition by

To Customers
iRay Technology Co. Ltd. 3
maintenance personnel.
4. Use only computers and image display monitors complying with IEC 60601-1 or
IEC 60950-1. For details, consult our sales representative or local dealer.
5. Use dedicated cables. Do not use cables other than those supplied with the
product.
6. Do not open the cover of the product without approval.
7. Request your sales representative or local dealer to install this product.
Caring for your environment
This symbol indicates that the product cannot be disposed of with your residential
or commercial waste.
Recycling Equipment
Please do not dispose of this product with your residential or commercial waste.
Improper handling of this type of waste will have a negative impact on health and
the environment. Some countries or regions, such as the European Union, have set
up systems to collect and recycle electrical or electronic waste items. Contact your
local authorities for information about practices established in your region. If
collection systems are not available, call official dealer for assistance.
Disclaimer
•Manufacturer shall not be liable for any damage, loss, or injury incurred to the
purchaser and the third parties as a result of fire, earthquake, any accident,
misuse or abuse of the product.
•Manufacturer shall not be liable for any damage, loss, or injury arising from
unauthorized modifications, repairs, or alterations or failure to strictly comply
with operation and maintenance instructions.
•Manufacturer shall not be liable for any damage or loss arising from use of any
option or consumer goods other than those dedicated as original products.
•It is the responsibility of users and physicians to maintain the privacy of image
data and provide a medical care service. Manufacturer shall not be responsible
for the legality of image processing, reading and storage, nor shall it be
responsible for loss of image data for any reason.
•Information regarding specifications, components, and appearance of the
product is subject to change without prior notice.
Copyright

To Customers
iRay Technology Co. Ltd. 4
All rights reserved
No part of this publication may be reproduced in any form or by any means without
the written permission of manufacturer. The information included is designed only
for use with product.
Trademarks
The iRay name and iRay logo are registered trademarks of iRay Technology Co.
Ltd.
Symbols and Conventions
The following symbols and conventions are used throughout the user guide.
This symbol is used to identify conditions under
which improper use of the product may cause
death or serious injury.
This notice is used to identify conditions under
which improper use of the product may cause
minor injury.
This notice is used to identify conditions under
which improper use of the product may cause
property damage.
This is used to indicate a prohibited operation.
This is used to indicate an action that must be
performed.
This is used to indicate important operations and
restrictions.
This is used to indicate operations for reference
and complementary information.
Labels and markings on the equipment
The labels and markings on the product are indicated below:
Marking
Description

To Customers
iRay Technology Co. Ltd. 5
Caution: please refer to instructions in the user manual.
This symbol is used to indicate that equipment has passed
CE testing, and it is followed by a CE number.
This symbol is used to identify the manufacturing series
number which is after, below or adjacent to the symbol. The
series number of the product is usually composed of 13 digits
as shown below:
This symbol is used to indicate the name and address of the
manufacturer.
This symbol is used to indicate the name and address of
authorized representatives in the European region.
This symbol is used to indicate the need to consult the user
guide for general information.
Safety Signs: please refer to the user guide for safety
instructions.
Safety Signs: Dangerous voltage levels.
Stand-by.
Handle with care.
Numerical Order
Year
Date
Month
Version
Product Code
A1A2A3A4 C1C2 M DD Y XXX

To Customers
iRay Technology Co. Ltd. 6
FPD is allowed to withstand 100kg on its surface
This symbol is used to indicate operation temperature range.
This symbol is used to indicate storage temperature range.
Non-ionizing radiation
FCC
Federal Communications Commission certificate
Package symbol: fragile.
Package symbol: keep away from sunlight.
Package symbol: keep dry.
Package symbol: this symbol is used to indicate humidity
range.
Package symbol: keep equipment upright.
Package symbol: do not roll package.
Package symbol: this symbol is used to indicate stacking limit
number.

To Customers
iRay Technology Co. Ltd. 7
Detector symbol: the device passes IPX4 test
Rx Only
Device is for prescription use only.

Contents
iRay Technology Co. Ltd. 8
1Safety Information ......................................................................................................................11
1.1 Safety Precautions 11
1.2 Notes for Use 15
2General Description ....................................................................................................................17
2.1 Scope 17
2.2 Lineup 17
2.3 Characteristics 18
2.4 Intended Use 18
2.5 Product Components 18
2.6 Components Description 20
2.6.1 Detector...............................................................................20
2.6.2 Battery Pack ........................................................................21
2.6.3 Battery Charger ...................................................................22
2.7 Product Specifications 23
2.7.1 Detector ...............................................................................23
2.7.2 Battery.................................................................................26
2.7.3 Battery Charger ...................................................................26
2.7.4 Environment........................................................................27
3Preparation ..................................................................................................................................28
3.1 Detector Installation 28
3.1.1 Attach Battery Pack.............................................................28
3.1.2 Booting Up ..........................................................................28
3.1.3 Adapter................................................................................31
4Operation ....................................................................................................................................31
4.1 Main Operation 31
4.1.1 Software Mode ....................................................................32
4.1.2 AED Mode ..........................................................................34
4.2 Connection Build 36
4.3 Panel Configuration 36

Contents
iRay Technology Co. Ltd. 9
4.4 Correction Template Generation 38
4.4.1 Pre-offset Template Generation...........................................38
4.4.2 Gain Template Generation...................................................40
4.4.3 Defect Template Generation................................................43
4.5 Image Check and Upload 45
4.5.1 Local Image Check..............................................................45
4.5.2 Panel Image Upload ............................................................46
4.5.3 Defect Template Check and Modification...........................48
4.6 Correction Template Management 49
4.6.1 Template Synchronization...................................................49
4.6.2 Correction Activation ..........................................................54
4.7 Firmware Update 56
4.8 Short cut 58
4.9 Software 59
4.9.1 Main GUI ............................................................................59
4.9.2 Home Page ..........................................................................59
4.9.3 Acquire Page .......................................................................60
4.9.4 SDK Page ............................................................................63
4.9.5 Detector Page ......................................................................64
4.9.6 Calibrate Page .....................................................................69
4.9.7 Local File Page....................................................................69
4.10 IT-network 70
4.10.1 Purpose for IT-network .......................................................70
4.10.2 Required characteristics ......................................................70
4.10.3 Required configuration........................................................70
4.10.4 Technical specifications ......................................................70
4.10.5 Intended information flow...................................................71
4.10.6 Hazardous Situations Resulting from Failure of the IT
Network 71

Contents
iRay Technology Co. Ltd. 10
4.10.7 Warning ...............................................................................71
4.10.8 Changes to IT Network Include: .........................................72
5Charger Installation.....................................................................................................................73
6Regulatory Information...............................................................................................................74
6.1 Manufacturer’s Information74
6.2 Medical Equipment Safety Standards 74
6.3 Guidance and manufacture’s declaration for EMC 77
6.3.1 EMI Compliance Table .......................................................77
6.3.2 EMS Compliance Table.......................................................78
6.4 Radio Frequency Compliance Information 80
6.5 Battery Safety Standards 81
6.6 Product Label 81
7Troubleshooting ..........................................................................................................................85
8Product Maintenance ..................................................................................................................86
8.1 Expected Service Life 86
8.2 Regular Inspection and Maintenance 86
8.3 Repair 86

Safety Information
iRay Technology Co. Ltd. 11
1Safety Information
1.1 Safety Precautions
Follow these safety guides and properly use the device to prevent injury and damage.
WARNING
Installation and environment
of use
Do not use or store the device near flammable chemicals such
as alcohol, thinner, benzene, etc.
If chemical is spilled or evaporates, it may result in fire or electric
shock through contact with electric parts inside the device. Also,
some disinfectants are flammable. Be sure to take care when
using them.
Do not connect the device with anything other than those
specified.
Doing so may result in fire or electric shock.
All patients with active implantable medical devices shouldbe
kept away from the device.
Power supply
Do not operate using any type of power supply other than those
indicated on rated label.
Otherwise, it may result in fire or electric shock.
Do not handle with wet hands.
You may experience electric shock that could result in death or
serious injury.
Do not place heavy objects such as medical equipmenton
cables and cords. Do notpull, bend, bundle, orstep on the
cables and cordsto prevent the sheath from being damaged,
and do not alter the cables and cords either.
Doing so may damage the cords which could result in fire or
electric shock.
Do not supply powerto more than one pieceof equipment using
the same AC outlet.
Doing so may result in fire or electric shock.
Do not turn on system powerwhen condensation has formed on
the device.
Doing so may result in fire or electric shock.
Do not connect multiple portable socket-outlets or extension
cords to system.
Doing so may result in fire or electric shock.
To avoid the risk of electric shock, the device must be
connected to a power supply with a protective earth.
Not doing so may result in fire or electric shock.

Safety Information
iRay Technology Co. Ltd. 12
Securely plug power cord into AC outlet.
If contact failure occurs or metal objects contact with exposed
metal prongs of the plug, this may result in fire or electric shock.
Be sure to turn off powerto each piece of the device before
connecting or disconnecting cords.
Otherwise, you may get electric shock that could result in death
or serious injury.
Be sure to hold plug or connector to disconnect cord.
If you pull cords, the core wire may be damaged, resulting in fire
or electric shock.
WARNING
Handling
Never disassemble or modify the device. No modification is
allowed.
Doing so may result in fire or electric shock. Also, since the
device contains components that may cause electric shock and
other hazardous parts, touching them may cause death or
serious injury.
Do not place anything on top of the device.
The object may fall and cause an injury. Also, if metal objects
such as needles or clips fall inside, it may result in fire or electric
shock.
Do not hit or drop the device.
The device may be damaged if receiving a strong jolt, which may
result in fire or electric shock if the device is used without being
repaired.
Do not put the device and pointed objects together.
It may be damaged. The device is recommended to be used in
Bucky.
Have the patient take a fixed posture and onlylet them touch the
parts of the device they need to touch.
If patients touch connectors or switches, it may result in electric
shock or malfunction.
When problem occurs
Should any of the following occur, immediately unplug the
power cord, and contact a sales representative or local dealer:
When there is smoke, odd smell or abnormal sound.
When liquid has been spilled inside or a metal object has
entered through an opening.
When the device has been dropped and damaged.
Maintenance and inspection
Please turn off the power of the device and unplug the adaptor
power cord before cleaning.
For safety reasons, never use alcohol, ether and other
flammable cleaning agent. Never use methanol, benzene, acid
and base because they will erode the device.
Don’t dip the device into liquid.
Please make sure that the device’s surface and plug are dry
before turning the device on.
Otherwise, it may result in fire or electric shock.
Clean theplug of the powercord periodicallyby unplugging it
from the AC outlet and removing dust or dirt from the plug, its
periphery and the AC outlet with a dry cloth.

Safety Information
iRay Technology Co. Ltd. 13
If the cord is kept plugged in for a long time in a dusty, humid or
sooty place, dust around the plug will attract moisture; this could
cause insulation failure that may result in fire.
For safety reasons, be sure to turn off the power to each piece of
the device when performing inspections indicated in this
manual.
Otherwise, an electric shock may occur.
CAUTION
Installation and environment
of use
Do not install the device in anyof the locations listed below.
Doing so may result in failure, malfunction, falling, fire or injury.
Close to facilities where water is used
Where it will be exposed to sunlight directly
Close to an air outlet of an air-conditioner or ventilation
equipment
Close to a heat source such as a heater
Where the power supply is unstable
In a dusty environment
In a saline or sulfurous environment
Where the temperature or humidity is high
Where there is freezing water or condensation
In areas prone to vibration
On an incline or unstable area
Take care that cables do not become tangled during use. Also,
be careful not to get your feet caught by the cable.
Otherwise, it may cause a malfunction of the device or injury of
the user due to tripping over the cable.
Non-medical equipment such as a battery charger and access
point cannot be used in the patient’s vicinity.
Power supply
Always connect the three-core power cord plug to the grounded
AC power outlet.
To make it easy to disconnect the plug at any time, avoid putting
any obstacles near the outlet. Otherwise, it may be impossible to
disconnect the plug in an emergency.
Be sure to ground the device to an indoor grounded connector.
Also, be sure to connect all the grounds of the system together.
Do not use any power source other than that provided.
Otherwise, fire or electric shock may be caused due to leakage.
Handling
Do not spill liquid or chemicals onto the device. In case the
patient is injured, do not allow blood or other body fluids to
contact the device.
Doing so may result in fire or electric shock.
In such situation, protect the device with a disposable cover as
necessary.
Turn off the power and pull out the plug to each piece of the
device for safety when not used.

Safety Information
iRay Technology Co. Ltd. 14
CAUTION
Handling
Handle carefully.
Do not submerge the device in water.
The internal image sensor maybe damaged if something hits it
or is dropped. If it is dropped, the shock label inside will turn red
and the device will not bewarranted by Manufacturer.
Do not place excessive weight on the device.
Otherwise, the internal image sensor may be damaged and
images may be incorrect
Uniform load：150 kg over the whole area of the detector
surface
Local load：100 kg on an area 4 cm in diameter
Be sure to use the equipment on a flat surface so it will not bend.
Otherwise, the internal image sensor may be damaged.
Be sure to securely hold the detector while using it in upright
positions. Otherwise, the detector may fall over, resulting in injury
to the user or patient, or may flip over, resulting in damage to the
device.

Safety Information
iRay Technology Co. Ltd. 15
Keep the
same load
(the same
pressure)
on the
detector
when
acquiring
an image,
or the
image will be incorrect.
CAUTION
Do not operate close to fire, do not use in high temperatures
Do not invert positive and negative poles
Do not contact with metal in case of a short circuit
Do not insert sharp objects into the battery
Do not hit the battery
Do not stand on the battery
Do not use the battery for purposes other than those stipulated in
the rules
Do not dispose of the battery or change its internal structure
Do not submerge the battery in water; please keep it dry in
storage and do not contact with water while in use
Please charge the battery with the charger provided by
Manufacturer
Do not mix the battery with ones not provided by Manufacturer
Do not charge the battery with a broken charger.
Charge the battery regularly to avoid over-discharge failure.
Do not use the battery when it is severe ballooning.
1.2 Notes for Use
When using the device, take the following precautions. Otherwise, problems may occur and there
may be a malfunction.
Before exposure
Be sure to check the device daily and confirm that it works properly.
Be sure there is a battery installed in the product to avoid a sudden power off

Safety Information
iRay Technology Co. Ltd. 16
Sudden heating of the room in cold areas will cause condensation to form on the
device. In this case, wait until condensation evaporates before performing an
exposure. If it is used while condensation is formed, problems may occur in the
quality of captured images. When an air-conditioner is used, be sure to
raise/lower the temperature slowly so that a difference in temperature in the
room and the device does not occur, to prevent condensation.
The detector should be warmed for more than 20 minutes before exposure or
updating gain or defect template.
During exposure
Do not move the power cable during exposure as it may cause image noise or
artifacts, or even incorrect images.
Do not use the equipment near detectors generating strong magnetic fields.
Otherwise, it may cause image noise, artifacts or even incorrect images.
Do not make an exposure within 60 seconds after 4 full range exposures.
Otherwise, the image will be incorrect. Do not make an exposure within 30
seconds after a full-range exposure. The larger the dose used, the longer the
wait should be before the next exposure.
During image acquisition, product should not be influenced in a physical or
electrical way.
After exposure
If the detector will not be used for 5 days, it is required to take out the battery. If
the battery will not be used for a long time, it must be charged to 30%~50%
every 3 months or 50%~70% every 6 months.
Disinfecting and Cleaning
After every examination, wipe the patient contact surfaces with disinfectants
such as Benzalkonium chloride or Benzalkonium bromide, to prevent the risk of
infection. For details on how to sterilize the device, consult a specialist.
Do not spray the detector directly with disinfectants or detergents.
Wipe it with a slightly damp cloth with a neutral detergent. Do not use solvents
such as alcohol, thinner, benzene, acid and base. Doing so may damage the
surface of the detector.
It's recommended to use a waterproof non-woven cover as an isolated layer
between the detector and blooding patient.

General Description
iRay Technology Co. Ltd. 17
2General Description
The product is a cassette-size wireless X-ray flat panel detector based on amorphous silicon thin-
film transistor technologies. It is developed to provide the highest quality of radiographic images,
and contains an active matrix of 2832×2836 with 150um pixel pitch. The detector’s scintillator has
two options: GOS (Gadolinium Sulfoxylate) and CsI (Caesium Iodide). However, the greatest
improvement is wireless communication between the detectors and PC. In addition, it can be
powered with a battery for portable panel use.
2.1 Scope
This manual contains information about the Mars1717XF. All operators must read and understand
this manual before using the device. All information in this manual, including illustrations, is based
on an equipment prototype. If your configuration does not have any of these items, information
about these items in the manual does not apply to your detector.
2.2 Lineup
Mars □ □- □
GSI: GOS; CSI: CSI
XF
1717: 17-inch X 17-inch
Mars series

General Description
iRay Technology Co. Ltd. 18
2.3 Characteristics
Wireless static Flat Panel Detector used for general radiography.
17 ×17 inch
AED trigger
Easy-to-change cable and charge in tray.
Battery rechargeable
IPX4
2.4 Intended Use
Wireless Digital Flat Panel Detector is intended for digital imaging solutions and designed to
provide general radiographic diagnosis of the human anatomy. It is intended to replace
radiographic CR andDR systems inall general-purpose diagnostic procedures. This device is not
intended for mammography or dental applications.
The detector can be used for general X-ray diagnosis of certain body parts. It is not intended for
mammography, dental applications, neonatal and fluoroscopy. More care should be taken when
making a diagnosis of people with allergies. In addition, it is also prohibited for use on pregnant
women. Shielding of none-inspection body areas is necessary during X-ray exposure. There is
no contraindication.
According to product’s intended use and results of risk management, essential performance is
identified and described as the following:
To acquire dark images, product shall be not influenced by imaging acquisition.
To maintain data transmission, product shall be not influenced by data and signal
transmission.
2.5 Product Components
The product is configured with the components below
Item
Description

General Description
iRay Technology Co. Ltd. 19
Mars1717XF Detector
Mars1717XF GSI/CSI
Medical adapter for
detector and battery
charger
24V (DC) power adapter
Battery pack
7.6V battery pack
Gigabit ethernet cable
Ethernet cable for
wireless router
AC power cable
AC cable for adapter

General Description
iRay Technology Co. Ltd. 20
Battery charger
Battery charger
User Manual
Paper print
CD-ROM
User Manual
Service tool
Note: The product package may be different based on requirements.
2.6 Components Description
2.6.1 Detector
External Signals Input and Control Panel
Control Panel