iRay Technology Mars1717VS User manual

Wireless Digital Flat Panel Detector
Mars1717VS
User Manual
Document Version: A0
Document ID: 119-201-01
Release Date: 2019.09.16
Before operating, please read this user manual and pay attention to all safety precautions.
Please ensure that this user's manual is properly maintained so that it can be accessed at any
time ( reserve ).
Please use it correctly on the basis of full understanding of the content.
E

iRay Technology Co., Ltd. 1
About FCC
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device must not cause harmful interference;
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Attention must be paid to the fact that changes or modifications not expressly approved by the
party responsible for compliance can void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This product generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this product
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
About SAR
This equipment complies with FCC exposure limits set forth for an uncontrolled environment.

To Customers
2 iRay Technology Co., Ltd
To Customers
Congratulations on your purchase of the Fixed Digital Flat Panel (hereinafter referred
to as Mars1717VS) which is manufactured by iRay Technology Co.Ltd. (Hereinafter
referred to as iRay).
At iRay, we strive to not only make the world-class products that deliver the best
value possible to our customers but also offer the highest quality of service and
customer care. Please take time to read through this user guide in order to utilize the
product effectively. We hope you enjoy the experience with iRay Mars1717VS.
If you have any questions or suggestions, please feel free to contact us.
Notes on usage and management of the equipment
1. Read all of the instructions in the user guide before your operation. Give particular attention
to all safety precautions.
2. Only a physician or a legally certified operator should use this product.
3. The equipment should be maintained in a safe and operable condition by maintenance
personnel.
4. Use only computers and image display monitors complying with IEC 60601-1 or IEC 60950-
1. For details, consult our sales representative or local iRay dealer.
5. Use only the dedicated cables. Do not use any cables other than those supplied with this
product.
6. Request your sales representative or local iRay dealer to install this product.

Mars1717V Digital Flat Panel Detector User Manual
iRay Technology Co., Ltd. 3
Caring for your environment
This symbol indicates that this product is not to be disposed of with your residential
or commercial waste.
Recycling iRay Equipment
Please do not dispose of this product with your residential or commercial waste.
Improper handling of this type of waste could have a negative impact on health and
on the environment. Some countries or regions, such as the European Union, have
set up systems to collect and recycle electrical or electronic waste items. Contact
your local authorities for information about practices established in your region. If
collection systems are not available, call iRay Customer Service for assistance.
Disclaimer
iRay shall not be liable to the purchaser of this product or third parties for any damage,
losse, or injury incurred by purchaser or third parties as a result of fire, earthquake,
any accident, misuse or abuse of this product.
iRay shall not be liable to any damage, loss, or injury arising from unauthorized
modifications, repairs, or alterations to this product or failure to strictly comply with
iRay’s operating and maintenance instructions.
iRay shall not be liable for any damage or loss arising from the use of any options or
consumable products other than those dedicated as Original iRay Products by iRay
Technology.
It is the responsibilities of the user/attending physicians for maintaining the privacy
of image data and providing medical care services. iRay shall not be responsible for
the legality of image processing , reading and storage nor it shall be responsible for
loss of image data for any reason.
Information regarding specification, compositions, and appearance of this product is
subject to change without prior notice.。
Copyright
All rights reserved
No part of this publication may be reproduced in any form or by any means without
the written permission of iRay. The information contained herein is designed only for
use with iRay Mars1717VS.
Trademarks
The iRay name and iRay logo are registered trademarks of iRay Technology Co.Ltd.

Mars1717VS Digital Flat Panel Detector User Manual
4 iRay Technology Co., Ltd..
Symbols and Conventions
The following symbols and conventions are used throughout the user guide.
This symbol is used to identify conditions under
which improper use of the product may cause death
or serious personal injury.
This notice is used to identify conditions under
which improper use of the product may cause minor
personal injury.
This notice is used to identify conditions under
which improper use of the product may cause
property damage.
This is used to indicate a prohibited operation.
This is used to indicate an action that must be
performed.
This is used to indicate important operations and
restrictions.
This is used to indicate operations for reference and
complementary information.

To Customers
iRay Technology Co., Ltd. 5
Labels and markings on the equipment
The contents of the labels and markings on iRay Mar1717VS product are indicated below:
Symbol Guide
Caution: please refer to the instructions in the user manual.
This symbol is used to indicate that the equipment has passed
CE testing and it is followed by the CE number.
This symbol is used to identify the manufacture series number which
is after, below or adjacent to the symbol. The series number of our
products is usually made of nineteen digits as shown below:
A1A2A3A4 B1B2 C1C2 L M1M2 D1D2 Y1Y2 X1X2X3X4
Numerical Order
Year
Date
Month
Production site
Version
Derived classes
Product Code
This symbol is used to indicate the name and address of the
manufacturer.
This symbol is used to indicate the name and address of iRay
authorized representative in the European region.
This symbol is used to indicate consultation of the user guide
for general information.
Safety Signs: please refer to the user guide for safety
instructions.
Safety Signs：Dangerous Voltage.
Handled with care.
This symbol is used to indicate the operational temperature
limits.
This symbol indicates the product radiates wireless signal.

Mars1717VS Digital Flat Panel Detector User Manual
6 iRay Technology Co., Ltd..
Package symbol, fragile.
Package symbol, keep away from sunlight.
Package symbol, keep dry.
Package symbol, keep the equipment up right.
Package symbol, do not roll the transportation package.
Type-B applied part
Package symbol, this symbol is used to indicate stacking limit
number.
×3 IPX3 for working surface only

Mars1717VS Digital Flat Panel Detector User Manual
7 iRay Technology Co., Ltd.
Contents
TO CUSTOMERS.......................................................................................................................... 2
CONTENTS .................................................................................................................................. 7
1. SAFETY ................................................................................................................................. 9
1.1 Safety Precautions ............................................................................................................... 10
1.2 Notes for Using of FPD ....................................................................................................... 14
1.3 Notes for Using of Battery .................................................................................................... 14
2. GENERAL DESCRIPTION ..................................................................................................... 16
2.1 Scope .................................................................................................................................... 17
2.2 Intended Use ......................................................................................................................... 17
2.3 Essential Performance .......................................................................................................... 17
2.4 Application Specification ....................................................................................................... 18
2.5 The Relative Position Between Patient And Detector ........................................................... 18
2.6 Product Components ............................................................................................................. 19
2.7 Components Description And Specification .......................................................................... 21
2.7.1 Detector ...................................................................................................................... 21
2.7.2 Battery ........................................................................................................................ 24
2.7.3 Battery Charger .......................................................................................................... 26
2.7.4 Power supply .............................................................................................................. 28
2.7.5 Recommended Application Condition ........................................................................ 28
2.7.6 Use Environment ........................................................................................................ 28
3. INSTALLATION ...................................................................................................................... 29
3.1 Panel Installation .............................................................................................................. 30
3.1.1 Attach Battery Pack .................................................................................................... 30
3.1.2 Attach DC Power ........................................................................................................ 31
3.1.4 Indicator ...................................................................................................................... 31
3.2 Battery Charger Installation .............................................................................................. 32
4. SOFTWARE SETUP ............................................................................................................ 33
4.2 Environment setup .............................................................................................................. 34
4.3 Connetion Mode .................................................................................................................. 34
4.4 Wired Connection Setup (Service Only) ............................................................................. 35
4.5 Client Mode Conneciton ...................................................................................................... 37
4.6 iDetector software ............................................................................................................... 45
4.7.1 HomePage ................................................................................................................. 46
4.7.2 Acquire Page ............................................................................................................. 47
4.7.3 Detector Page ............................................................................................................ 48
4.7.4 Calibrate Page ........................................................................................................... 49
4.7.5 Local Page ................................................................................................................. 49

Contents
8 iRay Technology Co., Ltd..
4.8 List of the HAZARDOUS SITUATIONS resulting from a failure of the IT-NETWORK ........ 50
5. OPERATION ........................................................................................................................... 51
5.1 Main Operation ...................................................................................................................... 52
5.1.1 Steps for acquiring image ......................................................................................... 53
5.1.2 Software Mode ............................................................................................................ 54
5.1.3 After Use ................................................................................................................ 57
5.2 Correction and Calibration Template Generation.................................................................. 58
5.2.1 Pre-offset Template Generation ................................................................................. 58
5.2.2 Gain Calibration Template Generation ....................................................................... 58
5.2.3 Defect Correction Template Generation ..................................................................... 59
5.3 Local Image Check ............................................................................................................... 59
5.4 Firmware Upgrade ................................................................................................................. 61
6. REGULATORY INFORMATION ............................................................................................. 63
6.1 Medical equipment safety standards ..................................................................................... 64
6.2 Guidance and manufacture’s declaration for EMC .......................................................... 66
6.2.1 EMI Compliance Table ............................................................................................... 66
6.2.2 EMS Compliance Table .............................................................................................. 66
6.3 Radio Frequency Compliance Information ............................................................................ 69
6.3.1 FCC Compliance ................................................................................................... 69
6.4 Battery Safety Standards ...................................................................................................... 70
7. TROUBLE SHOOTING ........................................................................................................... 71
8. SERVICE INFORMATION ...................................................................................................... 73
8.1 Service Office Info ................................................................................................................. 74
8.2 Product Lifetime .................................................................................................................... 74
8.3 Regular Inspection and Maintenance .................................................................................... 74
8.4 Repair .................................................................................................................................... 74
8.5 Replacement Parts Support .................................................................................................. 75
9. APPENDIX .............................................................................................................................. 76
9.1 Appendix A Information of Manufactures .............................................................................. 77
9.2 Appendix B Information of Medical Device Directive European Representative .................. 77

Mars1717VS Digital Flat Panel Detector User Manual
9 iRay Technology Co., Ltd.
1. Safety
1.1 Safety Precautions ................................................................................................................ 10
1.2 Notes for Using of FPD ....................................................................................................... 14
1.3 Notes for Using of Battery .................................................................................................... 14

Mars1717VS Digital Flat Panel Detector User Manual
10 iRay Technology Co., Ltd..
1.1 Safety Precautions
Follow these safeguards and properly use the equipment to prevent injury and damage to
any equipment/data.
WARNING
Installation and
environment of
use
 Do not use or store the equipment near flammable
chemicals such as alcohol, thinner, benzene, etc.
If chemicals are spilled or evaporate, it may result in fire or
electric shock through contact with electric parts inside the
equipment. Also, some disinfectants are flammable. Be
sure to take care when using them.
 Do not connect the equipment with anything other than
specified.
Doing so may result in fire or electric shock.
 All the patients with active implantable medical devices
should be kept away from the equipment.
Power supply
 Do not operate the equipment using any type of power
supply other than the one indicated on the rating label.
Otherwise, it may result in fire or electric shock.
 Do not handle the equipment with wet hands.
You may experience electric shock that could result in
death or serious injury.
 Do not place heavy object such as medical equipment
on cables and cords. Do not pull, bend, bundle, or step
on them to prevent their sheath from being damaged,
and do not alter them neither.
Doing so may damage the cords which could result in fire
or electric shock.
 Do not supply power to more than one piece of
equipment using the same AC outlet.
Doing so may result in fire or electric shock.
 Do not turn ON the system power when condensation
has formed on the equipment.
Doing so may result in fire or electric shock.
 Do not connect a multiple portable socket-outlet or
extension cord to the system.
Doing so may result in fire or electric shock.
 To avoid the risk of electric shock, this equipment
must only be connected to power supply with
protective earth.
Not doing so may result in fire or electric shock.
 Securely plug the power cord into the AC outlet.
If contact failure occurs, or if metal objects come into
contact with the exposed metal prongs of the plug, fire or
electric shock may result.
 Be sure to turn OFF the power to each piece of
equipment before connecting or disconnecting the
cords.
Otherwise, you may get an electric shock that could result
in death or serious injury.
 Be sure to hold the plug or connector to disconnect
the cord.

1. Safety
iRay Technology Co., Ltd. 11
If you pull the cord, the core wire may be damaged,
resulting in fire or electric shock.
WARNING
Handling  Never disassemble or modify the equipment. No
modification of this equipment is allowed. Parts of the
Mar1717VS that are not serviced or maintained while in
use with the patient.
Doing so may result in fire or electric shock. Also, since the
equipment incorporates parts that may cause electric
shock as well as other hazardous parts, touching them
may cause death or serious injury.
 Do not place anything on top of the equipment.
The object may fall and cause an injury. Also, if metal
objects such as needles or clips fall into the equipment, or
if liquid is spilled, it may result in fire or electric shock.
 Do not hit or drop the equipment.
The equipment may be damaged if it receives a strong jolt,
which may result in fire or electric shock if the equipment is
used without being repaired.
 Do not put the equipment and pointed objects together.
The equipment may be damaged. If so, the equipment
should be used in bucky.
 Have the patient take a fixed posture and do not let the
patient touch parts unnecessarily.
If the patient touches connectors or switches, it may result
in electric shock or malfunction of the equipment.
When a problem
occurs
 Should any of the following occurs, immediately
unplug the power cord of Control Box, and contact
your sales representative or local iRay dealer:
When there is smoke, an odd smell or abnormal sound.
When liquid has been spilled into the equipment or a metal
object has entered through an opening.
When the equipment has been dropped and damaged.
Maintenance and
inspection
 Please turn OFF the power of the equipment and
unplug the power cord of adaptor before cleaning.
 NEVER use alcohol, ether and other flammable
cleaning agent for safety. NEVER use methanol,
benzene, acid and base because they will erode the
equipment.
 DON'T dip the equipment into the liquid.
 Please make sure that the equipment's surface & plugs
are dry before turning ON.
Otherwise, it may result in fire or electric shock.
 Clean the plug of the power cord periodically by
unplugging it from the AC outlet and removing dust or
dirt from the plug, its periphery and AC outlet with a
dry cloth.
If the cord is kept plugged in for a long time in a dusty,
humid or sooty place, dust around the plug will attract
moisture; this could cause insulation failure that may result
in a fire.
 For safety reasons, be sure to turn OFF the power to
each piece of equipment when performing inspections
indicated in this manual.
Otherwise, electric shocks may occur.

Mars1717VS Digital Flat Panel Detector User Manual
12 iRay Technology Co., Ltd..
CAUTION
Installation and
environment of
use
 Do not install the equipment in any of the locations
listed below. Doing so may result in failure,
malfunction, equipment falling, fire or injury.
Close to facilities where water is used
Where it will be exposed to direct sunlight
Close to the air outlet of an air-conditioner or ventilation
equipment
Close to heat source such as a heater
Where the power supply is unstable
In a dusty environment
In a saline or sulfurous environment
Where temperature or humidity is high
Where there is freezing or condensation
In areas prone to vibration
On an incline or in an unstable area
 Take care that cables do not become tangled during
use. Also, be careful not to get your feet caught by
cable.
Otherwise, it may cause a malfunction of the equipment or
injury of the user due to tripping over the cable.
Power supply  Always connect the three-core power cord plug to a
grounded AC power outlet.
 To make it easy to disconnect the plug at any time,
avoid putting any obstacles near the outlet. Otherwise,
it may not be possible to disconnect the plug in an
emergency.
 Be sure to ground the equipment to an indoor
grounded connector. Also, be sure to connect all the
grounds for the system to a common ground.
 Do not use any power source other than the one
provided with this equipment.
Otherwise, fire or electric shock may be caused due to
leakage.
Handling  Do not spill liquid or chemicals onto the equipment. In
case the patient is injured, it is not allowed to contact
with blood or other body fluids.
Doing so may result in fire or electric shock.
In such a situation, protect the equipment with a disposable
cover as necessary.
 Turn OFF the power and pull out the plug to each piece
of equipment for safety when not used.

1. Safety
iRay Technology Co., Ltd. 13
CAUTION
Handling  Handle the equipment carefully.
 Do not submerge the equipment in water.
 The internal image sensor may be damaged if
something hits against it or it is dropped.
 Do not place excessive weight on the equipment.
 Otherwise, the internal image sensor may be damaged
and image may be incorrect.

 <Load Limit>
 Uniform load：150 kg over the whole area of the
detector surface.
 Local load：100 kg on an area 4 cm diameter.
 Be sure to use the equipment on a protected foam.
Otherwise, the internal image sensor may be damaged.
Be sure to securely hold the detector while using it in
upright positions. Otherwise, the detector may fall
over, resulting in injury to the user or patient, or may
flip over, resulting in damage to the inner device.
Keep the same load (same pressure) on the detector when
acquiring the image. Otherwise, the image will be incorrect.
CAUTION
 Do not close to fire, do not use in high temperature
 Do not invert positive and negative pole
 Do not contact with metal in case of short circuit
 Do not insert sharp objects into battery
 Do not beat battery
 Do not stand on battery
 Do not use battery out of rules
 Do not dispose battery or change internal structure
 Do not submerge battery in water, please keep dry in
storage and do not contact with water in use
 Please charge battery with charger following IEC60601-
1 & IEC62133 Standards provide by us
 Do not mix battery with ones not provided by our
company
 Do not charge battery with broken charger.

Mars1717VS Digital Flat Panel Detector User Manual
14 iRay Technology Co., Ltd..
1.2 Notes for Using of FPD
When using the equipment, take the following precautions. Otherwise, problems may occur
and the equipment may not function correctly.
Before exposure
 Be sure to check the equipment daily and confirm that it works properly.
 Be sure there be a battery installing on the Mars1717VS to avoid the power off
suddenly
 Sudden heating of the room in cold areas will cause condensation to form on the
equipment. In this case, wait until the condensation evaporates before
performing an exposure. If the equipment is used while condensation is formed
on it, problems may occur in the quality of captured images. When an air-
conditioner is used, be sure to raise/lower the temperature gradually so that a
difference of temperature in the room and equipment does not occur, to prevent
condensation.
 The detector should warm up for 15 minutes before exposure or updating the
gain map or defect map.
During exposure
 Do not move the power during exposure, or it may cause image noise or
artifacts, even incorrect images.
 Do not use the devices near the equipment generating a strong magnetic field.
Otherwise, it may cause image noise, artifacts or even incorrect images.
Disinfection and Cleaning (When in portable usage)
 After every examination, wipe the patient contact surfaces of the detector using
disinfectants such as ethanol, to prevent the risk of infection. For details on how
to sterilize, consult a specialist.
 Do not spray the detector directly with disinfectants or detergents.
 Wipe it with a cloth slightly damped with a neutral detergent. Do not use solvents
such as alcohol, thinner, benzene, acid and base. Doing so may damage the
surface of the equipment.
 It's recommended to use a waterproof non-woven cover as the isolated layer
between detector and the blooding patient.
1.3 Notes for Using of Battery
 Battery is shipped with detector, remaining capacity should be charged greater
than or equal to 50% but less than 60%. If storage without use, charge greater
than or equal to 50% but less than 60% every 3 month, or it causes damage to
battery.

1. Safety
iRay Technology Co., Ltd. 15
 Battery is shipped in package without detector, remaining capacity should be
charged greater than or equal to 20% but less than 30%, If storage without use,
charge greater than or equal to 20% but less than 30% every 2 month, or it
causes damage to battery.
If battery remaining capacity is lower than 20%, delivery is not allowed, or it is
possible to be over discharge.
Battery storage and working environment should strictly follow specification. If
there is any objection, there is possibility to damage performance
If battery is not used in detector, please detach it.

Mars1717VS Digital Flat Panel Detector User Manual
16 iRay Technology Co., Ltd.
2. General Description
2.1 Scope .................................................................................................................................... 17
2.2 Model ........................................................................................................... 错误!未定义书签。
2.3 Characteristic............................................................................................... 错误!未定义书签。
2.4 Intended Use ......................................................................................................................... 17
2.5 Essential Performance .......................................................................................................... 17
2.6 Application Specification ....................................................................................................... 18
2.7 The Relative Position Between Patient And Detector ........................................................... 18
2.8 Product Components ............................................................................................................. 19
2.9 Components Description And Specification .......................................................................... 21
2.9.1 Detector ...................................................................................................................... 21
2.9.2 Battery ........................................................................................................................ 24
2.9.3 Battery Charger .......................................................................................................... 26
2.9.4 Power supply .............................................................................................................. 28
2.9.5 Recommended Application Condition ........................................................................ 28
2.9.6 Use Environment ........................................................................................................ 28

2. General Description
iRay Technology Co., Ltd. 17
Mars1717VS is a cassette-size wireless X-ray flat panel detector based on amorphous
silicon thin-film transistor technologies. It is developed to provide the good quality of
radiographic image, which contains an active matrix of 3070×3070 with 139um pixel pitch.
Panels’ scintillator is CsI (Cesium Iodide). Mars1717VS supports wireless communication
between panel and Workstation, and can be used as a real portable panel.
2.1 Scope
This manual contains information about the Mars1717VS. Information in the manual,
including the illustrations, is based on prototype. If your configuration does not have any of
these items, information about these items does not apply to your panel.
2.2 Intended Use
Mars1717VS Wireless Digital Flat Panel Detector is indicated for digital imaging solution
designed for providing general radiographic diagnosis of human anatomy. It is intended to
replace radiographic film/screen systems in all general-purpose diagnostic procedures. This
panel provides digital X-ray imaging for diagnosis of disease, injury, or any applicable health
problem. The image is obtained as the result of X-ray passing through the human body and
detected by detector.
iRay would provide hardware and software support for integration of system.
This panel is not intended for mammography or dental applications.
2.3 Essential Performance

Mars1717V Digital Flat Panel Detector User Manual
18 iRay Technology Co., Ltd..
According to the Mars1717VS series INTENDED USE and the result of risk management,
image acquisition and data transmission are defined as ESSENTIAL PERFORMANCE.
Getting dark image proves that ESSENTIAL PERFORMANCE does not influence
INTENDED USE. Method for getting dark image in detail refers to section “installation” and
“operation”
2.4 Application Specification
PATIENT population:
Age: except for children
Weight: not relevant
Health: not relevant
Nationality: multiple
Gender: except for pregnant women
Intended OPERATOR:
All of use, maintenance and operation steps should be carried out by the operator
who has accepted the professional training offered by the company's customer
service staff.
Life-time:
Life-time: 5 years without frequency limit
2.5 The Relative Position Between Patient And Detector
Because of the crosstalk effect of Amorphous silicon flat-panel detector, Pay
attention to the relative position of patient and detector, the recommended position
as shown below, Otherwise, the image is prone to abnormal light lines.