Irradiant SSDL-3201RGB User manual

1
USER MANUAL
(SSDL-3201RGB)

2
TABLE OF CONTENTS
INTRODUCTION............................................................................................................3
MAIN FEATURES...................................................................................................................3
UNPACKING...........................................................................................................................3
SAFETY WARNING....................................................................................................3
PANEL REVIEW..............................................................................................................4
INSTALLATION AND SETTING......................................................................4
1. MULTI-FIXTURES CONNECTION..................................................................................4
2. LAMP BODY INSTALLATION..........................................................................................4
2. DMX CHANNEL SUMMARY...........................................................................................5
3. CHANNEL FUNTIONS......................................................................................................6
4. ABOUT EACH CHANNEL ................................................................................................7
MAINTENANCE............................................................................................................10
1.TROUBLESHOOTING.....................................................................................................10
2. CLEANING........................................................................................................................10
TENICAL SPECIFICATION...............................................................................11

3
INTRODUCTION
Thanks for your purchase of our product, SSDL-3201RGB High Power LED Moving Head.
It can works under auto mode and sound -active mode with 16 built-in programs. The
product has a long lifespan and low power consumption. It is exquisite and applicable for
all kinds of entertaining occasions. Before you begin, please read instructions carefully. If
you meet with any problem, please contact with your distributor nearby.
MAIN FEATURES
■DMX-512 control, 11 channels
■DMX, AUTO, SOUND-ACTIVE mode
■RGB control with 255 grades
■RGB total dimmer is 0~100%
■Shutter speed is 10/sec ~1/10secs
■36X3IN1 LED
■PAN scan angle 0~5400
■Tilt scan angle 0~2300
UNPACKING
★SSDL-3201RGB High Power LED Moving Head
★USER MANUAL
SAFETYWARNING
For your convenient and accurate operation, please read following information
carefully.
◆Suitable for indoor use only.
◆Put it in a dry, well -ventilated place in case of short cut caused by erosion of moisture
and rain.
◆Do not install it nearby hot sources in case that rising temperature of lamp damages
itself.
◆Do not barrier vent in order to ventilate well and dissipate in time.
◆Connect the fixture with power source, which has a ground line, and voltage of power
source should accord with rating voltage.
◆If fuse was damaged, change the same type.
◆You can only choose accessories the manufacturer provides when need repairing.
◆Ambient temperature of the lamp should not exceed 40℃
◆If any problem, contact with professional technicians working in our after-sales service
department.

4
PANELREVIEW
FUN: function menu or withdraw the last menu
ENTER: enter the next menu or definite present value.
UP: increase one step each time
DOWN: decrease one step each time.
INSTALLATION AND SETTING
1. MULTI-FIXTURES CONNECTION
The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive
(S+).
2. LAMP BODY INSTALLATION
Notes: do not install it nearby the curtain or flammable materials.
Only for indoor use.

5
OPERATION
1.SET DIPSWITCHES
■Each fixture occupies 11 DMX channels.
■DMX 512 signal can control multi-fixtures together, however you must set DMX address
of each lamp first. Different DMX address will lead to different movements.
■You can set DMX address from 1~501 on the multi-function display panel.
■Switch on power supply and after finishing resetting, the panel will show 001,that is to
say DMX address is 1 and the first lamp has been controlled by 1~11channels.In turn the
second fixture has been controlled by 12~22 channels. (When panel shows 001,press
UP button until it shows 012.Then just press ENTER button). In the same way, the third
fixture has been controlled by 23~33 channels and the panel shows023.
■Through this method, you can control multi-fixtures to perform different movements.
2. DMX CHANNEL SUMMARY

6
3. CHANNEL FUNTIONS
DISPLAY FUNCTION
VALUE 001-501(503) DMX address (16BT is on, the max value is 501.
M-DM DMX mode
M-AU AUTO mode
MODE
M-SO SOUND mode
PRCO PR1~8 8 built-in programs
Pr1-4 means skip
Pr5-8 means fade
SPCO SP01~15 Auto speed is 0.1~10 seconds each step
STND Run clockwise as DMX value increasesr PAN REV Run anticlockwise as DMX value decreases
STND Run clockwise as DMX data increaseR TILT REV Run anticlockwise as DMX data decreases
STND CH7: PAN, CH8: TILE, CH10: PAN FINE, CH11: TILT FINE.r-PT REV CH7: PAN, CH8: TILT, CH10: PAN FINE, CH11: TILT FINE.
ALL Check all channels with motors
PAN Check pan channels
TITL Check tilt channels
RED Check red channels
GREEN Check green channels
TEST
BLUE Check blue channels
STND Display bites normallyDISP REV Display bytes upside down
REST REST/ON Reset
ON PAN, TILT is 16 bit, CH10: PAN FINE, CH11: TILT FINE.
16BT OFF PAN, TILT is 8 bit. CH10, CH11 does not exist.

7
4. ABOUT EACH CHANNEL
■ Channel 1:DMX MODE
Ch DMX Function CH2 CH3 CH4 CH5 CH6
0~24 RGB Red
0~255 Green 0~255 Blue 0~255 Shutter 0~255 Dimmer 0~255
25~49 Built-in program
1
50~74 Built-in program
2
75~99 Built-in program
3
100~124 Built-in program
4
125~149 Built-in program
5
150~174 Built-in program
6
175~199 Built-in program
7
200~224 Built-in program
8
Auto
speed
CH1
225~255 Sound-active
program
No
function No function No function
No
function
No
function
■Channel 2: RED
When CH1 is 0~24
DMXvalue red
255 carmine
0 0

8
■Channel 3：GREEN
When CH1 is 0~24
DMXvalue green
255 bottle green
0 0
■Channel 4:Blue
When CH1 is 0~24
DMXvalue blue
255 navy blue
0 0
■Channel 5：Strobe
When CH1 is 0~24
DMX value strobe speed
255 slowest
16 fastest
15 nostrobe
0 no strobe
Notes: CH2~4 decides brightness. When CH2, CH3, CH4 is 0, there is n
o
brightness.

9
When CH1 is 25~224:
DMX value AUTO speed
255 slowest
0 fastest
■Channel 6：RGB Dimming
When CH1is 0~24:
DMX value RGB brightness
255 0
0 brightest
■Channel 7: PAN（540°）
NO. DMX value Effect
1 0 Leftmost
2 127 Medium
3 255 Rightmost
■Channel 8: TILT（230°）
NO. DMX value Effect
1 0 Bottommost
2 127 Medium
3 255 Topmost

10
■Channel 9：PAN or TILT SPEED
■Channel 10 : PAN FINE (2.4°)
■Channel 11:TILT FINE (2.4°)
Notes: When 16 BT is on, CH10, CH11 exists; otherwise they do not exist.
MAINTENANCE
1.TROUBLESHOOTING
Problem Probable cause(s) Suggested remedy
No power source Check if power source is on or
cord works well.
Fixtures does not work
Fuse burnt
Cut off power source and change
the same type fuse. If fuse was
burnt on end, it may be the
problem of connection; Find
qualified professors to repair.
False or incomplete
data connection
Check, repair or change the data
line. Ensure connection is well
and the first lamp’s single input is
connected with the controller
output.
False address setting Check DMX address.
Problem of signal
connector of some
fixtures
Pull out the signal output and
input of one fixture. Then connect
both directly. If it works well, this
fixture is proved to be the failed
one. Handle the rest fixtures alike
to check which fixture has
problems. If any problem, please
connect the technician.
Reset normally, but console
abnormally or no response
Signal output does
not match with the pin
(pins2 and pins3 has a
wrong sequence)
Toggle the PHASE button on the
controller to reverse the polarity.
2. CLEANING
Though increasing reliability by designing well and we never stop to improve quality to
lengthen lamp’s lifespan. It is still indispensable to maintain it well by certain time in order