IrriGreen Irrigreen2 User manual

IrriGreen2® App Guide
Android
Mobile App Video
Irrigreen.com/professionals-logged-in/
Password: goirrigreen!
IG2-APP-1.0.0 1
One Head per Zone … Software Does the Rest!!

Getting Connected
IrriGreen Wi-Fi Network & App Startup Steps
1. Download IrriGreen2 app with “iG2” logo:
2. Go to your device Settings
3. Go to Wi-Fi Settings
4. Find IrriGreen network
5. Log onto IrriGreen network
6. Enter 10 digit password on Controller removable label
5. Start IrriGreen2 app
6. Add Customer
7. Select Customer
8. Dashboard screen appears
Log-in Hints
A. Make sure in Wi-Fi range of Controller
B. Password entered correctly
C. Device sees network but doesn’t connect?
Your device settings may prevent it logging onto
Wi-Fi networks without Internet access
(e.g. “Wi-Fi optimization”)
2

Log on IrriGreen® Wi-Fi Network: Steps 1-3
1. Go to your mobile device Settings
2. Go to Wi-Fi Settings
3. Find IrriGreen network
Android iOS
IrriGreen
Wi-Fi
network
address
Note:
No need to log
onto property
owner’s Wi-Fi
network
3
Wi-Fi Range: Wi-Fi is a low-power radio signal
Controller location, landscape elevations (signal
going through soil), house construction (stucco,
steel, etc.) … all affect Wi-Fi range. Use Wi-Fi
extenders to extend range while mapping zones.
IrriGreen has Wi-Fi extenders available

Log on IrriGreen® Wi-Fi Network: Step 4
4. Enter 10 digit password on removable label
Log-in Hints
A. Make sure you are in Wi-Fi range of Controller, check Wi-Fi signal strength meter
B. Password entered correctly, check UPPER/lower cases
C. Device sees network but doesn’t connect. (Device settings may be preventing it from
logging onto a Wi-Fi networks without Internet access … sometimes called “Wi-Fi
optimization”, look in Network Settings on your device
D. May have to click on a “Yes, connect, No Internet Access” type message on your device 4
0123456789
0123456789

Start App: Steps 5-7
7. Highlight Customer
and click Select
6. Add Customer
Name and address
5. Tap on
IrriGreen 2
Mobile App
(iG2 logo)
NOTE:
iOS security
requires logging
into the network
before starting
the app 5

Dashboard Appears: Step 8
Last Watering Day, Gallons Used Last Watering Event, Gallons
Used Last Week/Last Quarter, Run Time & System Status
Android iOS (Available 1Q 2020)
NOTE:
If notice appears,
touch & hold to
clear.
If it re-appears,
zone may not be
running properly,
contact your
installer.
6

Home Wi-Fi Network Rollover
Required for Cloud Monitoring / Updates
7
•For IrriGreen2 system monitoring, roll the
system over to the property owner’s Wi-Fi
network for internet access
•Rolling the Wi-Fi over to the property’s Wi-Fi
network will typically improve Wi-Fi range for
zone mapping
•IrriGreen will update system software remotely

Rolling System Over to Home Wi-Fi Network
1. Go to IrriGreen App Dashboard
2. Select Network, Click on Connect to Home Network
3. Enter Home network name and Password
4. Click Connect
5. IrriGreen Wi-Fi network will disappear from your Wi-Fi Settings
6. Log into your Home network and start IrriGreen2 app
8
NOTE: Pushing Reset Button or unplugging system briefly will
allow logging into the IrriGreen Wi-Fi network for 90 seconds
(typically for Contractor access to system)

App Navigation
Android
Upper left icon opens menu
iOS
Menu on Bottom of Screen
NOTE:
IrriGreen
system clock is
set to the
mobile device
time whenever
the app opens
the Dashboard
The two AAA
batteries in the
Controller are
for system clock
backup.
Replace yearly.
9

System Settings: Step 1
Go to Setups Page
Android iOS (Available 1Q 2020)
10

System Settings: Step 2
A. Click & hold
“Press to Edit”
B. Popup menu will appear
(3 Digital Zones shown)
11

Red Flow Sensor lead to
Controller Terminal“Sen1”
12
System Settings: Step 3
Select Flow Meter 1 (Wire Red Flow Sensor lead to “Sen1”, Black
lead to “Common” Terminal
Black Flow
Sensor lead
to“Common”

System Settings: Step 4
Select Sensor Inputs for any Rain or Soil Moisture Sensors (SMS)
(No Sensor Inputs is the default)
A. Click “Sensor: None”(default)
B. Sensor Input Menu appears
C. Select “None”, “1”, or “2” Sensor inputs
No Sensor Inputs (Default)
1Sensor (Rain sensor or SMS)
2Sensor (Rain and Soil Moisture)
13

IrriGreen Enables the Digital Zones
for an Installation at the Factory
A. Go to Setup Page
B. Click Digital Zone #
C. Select “Digital Zone” for
all Digital Zones needed
14
There are 16 (or 32)
Digital Zones
available, as two (or
four) separate
sequences of eight.
You may divide the
zones up between the
two separate
sequences of eight.
Example:
Seven Digital Zones
could be:
Digital Zones 1-7
OR
Digital Zones 1-4 and
Digital Zones 9-11
To enable Digital Sprinkler Zones
(if needed):

Sprinklers are Pre-numbered for each Zone
Sprinklers will run in that numerical order*
Locate sprinklers in the order you want them to run
15
Digital Sprinklers have Zone Numbers 1-16
assigned at the factory
Zone Number on Sprinkler box Zone Number on Sprinkler
*Head #1 runs first
Head #2 runs second
Head #3 runs third
Etc.

Connect up to Eight Sprinklers
per Controller Cable
Connect sprinklers with Sprinkler Cables and Cable Tees
Digital Zones 1-8:
Wire Controller Cable to “iG 1-8” and “Common”
Locate Sprinklers numbered 1-8 in the order you want them to run on the landscape
Digital Zones 9-16:
Wire second Server Cable to “iG 9-16” and “Common”
Locate Sprinklers numbered 9-16 in the order you want them to run on the landscape (after 1-8)
DO Install Cables in a trench or pull a parallel run of 1 inch pipe as conduit for Cables
DON’T pull IrriGreen Cables
DO loop excess Cable inside a valve box adjacent to the head, buried below turf
DON’T cut and splice IrriGreen Cables
DO branch out your Cables in different directions with Tees
Use a 6FT Plug-n-Play Cable Tee; use supplied End Plug to seal the last Sprinkler connector plug
DO add a second Controller Cable if branching off immediately from the Server
DO protect all Digital Sprinkler connections with small valve boxes, buried below turf

Calibrate & Map Digital Zones: Steps 1-2
1. Select Zones 2. Select Zone to Map
Only Digital Zones Appear*
*NOTE:
Valve zones
will appear
on the
Schedule
Page
17

Calibrate & Map Digital Zones: Steps 3-4
Calibrate Each Digital Zone Before Mapping
3. Yes, Calibrate
Takes about 4 minutes
Head pops up several times
4. Start Programming?
Yes
NOTE:
If zone has
been
calibrated,
select
“NO”
Hint:
Sprinkler not
tracking zone
properly?
Check for debris
in filter; if clean,
then recalibrate
the zone. If you
recalibrate, may
need to re-map. 18
Head will pop up
and spray ~15’ at
Position “0”

Calibrate & Map Digital Zones: Steps 5-7
Program/Map Sprinkler to Zone Shape
5. Click/Hold “Rotate” to turn
streams
437 Rotation settings, every 0.8o
Clockwise rotation only
6. Click “- / +(Minus/Plus)”
to Set Distance
Distance (~6” increments)
Distances are approximate
7. Click “Insert” to create Positions
System draws a straight line between
any two points/positions
Water streams
Digital Sprinkler
19

Programming Hints
•Set points to track about
6” from zone edges
•Up to 50 map points are
allowed per zone
•“Best practice” is to use
minimal number of
positions/map points to
create zone shape and add
points as needed to
optimize tracking
20
•When zone is started up, it
will spray at Rotation “0”
and 15 feet
•It will turn only when you
tap/hold “Rotate”
•The zone startup (Position
1) may be set to any
Rotation (0-437), but the
first Position distance must
be 10+ feet to fully pop up
and seat the riser