iseeBell WF100UK Operating and safety instructions

INDOOR CHIME
1
Setup
Mode
Rings
Light Sensor
Speaker
LED
Red signifies
status while
white means
night light
Volume Connector
Slot
Release
Button
AC Adapter
Plug Slot
Features
• Chime and light notification
• Choose from 25 ringtones
• Volume control
• Night light
• Pair up to 3 iseeBell devices
• 110-yard transmission distance
Front Back
INDOOR CHIME
SETUP
GUIDELINES
INDOOR CHIME &
NIGHTLIGHT

INDOOR CHIME
Step 1 Set up your device
• Plug your iseeBell indoor chime into a 100 –
240v outlet. It will let out a beep, light up,
then off.
• Press the Mode button, so that it switches
between “chime only”, “light only” and “both
chime and light”. Select your preferred mode
for when someone rings the bell. “Chime
only” will beep once. For “light only”, the
LED blinks once while “Both Chime and
light” will have your iseeBell beep once and
LED blinks once as well.
Step 2 Pair your iseeBell indoor chime with
your iseeBell video doorbell
• Press and hold the Setup button for 5 seconds.
• LED light will turn red and indoor chime will
enter pairing mode with a beep.
• Press the Call button on your iseeBell Video doorbell while
in pairing mode.
• Indoor chime will react accordingly based on your mode
selection.
• To exit, press the Setup button and it will beep twice.
• Indoor chime will automatically exit pair mode after 10
seconds if you don’t press any buttons.
• Important note: One indoor chime can pair with at most
3 video doorbells.
How to set it up
3
INDOOR CHIME
2
• To assemble, line up
the AC adapter plug
with the slots. Then
push the plug in and
twist until it clicks.
• To disassemble, press
and hold the release
button and twist the
AC adapter plug.
Assemble Disassemble Available AC adapter plug
UKEU
AUSTRALIAUS/CANADA

INDOOR CHIME
Select a Ringtone
Press the Rings button to select the one you
like. You have up to 25 choices.
Control the volume
• Press the Volume button to turn up the
volume.
• Keep on pressing the button to loop among
high, medium and low.
• Choose the volume level you want.
Select Night light mode
• Press and hold Mode button, it will beep
once and LED will blink white. It is now
in Auto mode. The LED will light up
at night and will go off when it is bright out.
• Or Press and hold the Mode button. It will
beep twice and LED will light white. It is in
LED mode and LED will light up all the time.
• To put off night light, press and hold the
Mode button. It will beep three times and
LED will go off. This is the dark mode
and LED will not light up at all.
4
INDOOR CHIME
Restore to factory settings
• Unplug the indoor chime first.
• Press and hold Setup and Mode buttons
at the same time.
• Keep holding the two buttons and plug the
indoor chime.
• The chime will beep once. The LED will
blink.
• Release the two buttons.
• The indoor chime is now set to factory
• default settings.
• It will beep once again.
Customer Service
If you encounter any challenges during product
installation, kindly visit www.iseebell.com/support
or call us for help.
Website: www.iseebell.com/support
24hr toll-free：1.888.600.4010
Email：[email protected]
5

GUIDE
ADJUSTABLE
WALL MOUNT
INSTALLATION
WALL MOUNT
Swivel-ball Knuckle Swivel Fixture Mount Screws
Meet the content in your box of adjustable wall mount
1

WALL MOUNT
3
WALL MOUNT
2
Step 1. Secure your iseeBell
• Pass the wires to the small notch at the
bottom of
the Swivel-ball Knuckle.
• Line up the holes in the Wall Bracket of
iseeBell
Doorbell with the slots on the Swivel- ball
Knuckle.
Notch
Step 2. Install the Swivel Fixture Mount
• Gently pull the wire down.
• Snap the ball of the knuckle into the fixture mount.
• Once done, attach it to any metal surface.
Install the Screws (optional)
To mount it on any surface other than metal, use the
screws and anchors to secure the Fixture Mount.
Tips: Hide the wires
If you prefer to hide the wires, you can also pass the
wires from power adaptor through the center of the
Swivel Fixuture Mount and the Swivel-ball Knuckle.
And the other steps will be the same.