IV Produkt Flexomix MIE-EF Installation guide

IV Produkt’s continuous product development may give rise to specification changes without prior notice.
Product sheet
Operation and MaintenanceFlexomix MIE-EF
2015-01-071 (2)
Humidifier fitting (code MIE-EF)
The fitting is selected together with an evaporative
humidifier (code EFEF) with cold humidifying surfaces
that can also be used for evaporative cooling.
The fitting consists of a humidifier block, water
reservoir, water distribution system and housing front
section for integration into the standard module (code
EMM).
• The water reservoir is made from stainless steel.
Spraybars and pipe parts are made from PVC
plastic.
• The humidifier is made from a specially
impregnated composite material.
• Two different versions of the humidifier are
available:
circulating water or direct water.
A droplet eliminator is also available.
• The humidifier is available with two different
humidification rates:
max. 85% (FA6-85) or max. 95% FA6-95).
• A pump is included as standard for humidifiers
using circulating water.
For further information on humidifiers, see Munters
FA6, product sheet at ivprodukt.se.
Accessories for fitting
• Mounted damper motor (code KJST-04)
• Water trap (code MIET-CL-04)
Integral attenuation (dB)
Octave band
intermediate
frequency (Hz) 63 125 250 500 1,000 2,000 4,000 8,000
EFEF
85% 3 2 2 3 5 6 12 15
95% 3 2 3 3 5 7 13 16
Technical data, sizes 150–950
Configuration MIE-EF
Sizes 150–600
Sizes 740–950
Configuration humidifier
Circulating water Direct water
Water consumption
Circulating water
The total water consumption is determined by the
amount of evaporated and bled-off water respectively.
To calculate the water consumption, see Munters FA6
Technical manual at ivprodukt.se.
Direct water
Total water consumption (T) for direct water:
Size
Configuration
FA6-85 FA6-95
150 6.3 6.3
190 8.0 8.0
240 8.5 8.5
300, 360 10.0 10.0
480, 600 12.0 12.0
740 15.0 15.0
750 12.0 12.0
850 15.0 15.0
950 12.0 12.0

IV Produkt’s continuous product development may give rise to specification changes without prior notice.
Product sheet
Operation and MaintenanceFlexomix MIE-EF
2015-01-072 (2)
Operation and maintenance
instructions
The purpose of the air humidifier is to add moisture to
an air flow. One operation case is to add moisture to
the supply air, another is to add moisture to the extract
air in order to reduce the air temperature before the air
passes through e.g. a rotary heat exchanger (evapora-
tive cooling).
Faulty function leads to a lower humidification rate.
If the humidifier is not going to be used for a long period,
the humidifier block should be removed, cleaned and
stored appropriately.
For instructions on how to use the humidifier,
see Munters FA6, operation and maintenance at
ivprodukt.se.
Electrical data for circulation pump
Enclosure class IP54.
Size
Configu-
ration
Voltage
3-phase (V)
Output
(W)
Rated current
∆ / Y (A)
150 FA6-85
FA6-95 ∆230/Y400 49 0.26/0.15
190, 240,
300, 360,
480, 600,
750
FA6-85 ∆230/Y400 49 0.26/0.15
FA6-95 ∆230/Y400 75 0.38/0.22
740, 850
FA6-85 ∆230/Y400 75 0.38/0.22
FA6-95 ∆230/Y400 140 0.71/0.41
950 FA6-85
FA6-95 ∆230/Y400 75 0.38/0.22