jablotron 100+ User manual

User manual
JABLOTRON 100+_COVER_EN_MMD55500.indd 1 25.9.2018 14:42:29

1
TABLE OF CONTENTS
1. INTRODUCTION 3
2. OPERATING THE JABLOTRON 100+SYSTEM 3
2.1 ON-SITE OPERATING 5
2.1.1 USING THE SYSTEM KEYPAD 5
2.1.2 KEYPAD CODE AUTHORIZATION 7
2.1.2.1 ALARM SETTING 9
2.1.2.2 ALARM UNSETTING 9
2.1.2.3 DURESS ACCESS CONTROL 10
2.1.2.4 PARTIAL ALARM SETTING 10
2.1.2.5 TERMINATING A TRIGGERED ALARM 10
2.1.2.6 SECTION CONTROL FROM THE MENU OF THE KEYPAD WITH AN LCD DISPLAY 11
2.2.1 USING THE JA-110E AND JA-150E SYSTEM KEYPADS 12
2.2.1.1 ALARM SETTING 14
2.2.1.2 ALARM UNSETTING 14
2.2.1.3 PARTIAL ALARM SETTING 15
2.2.1.4 DURESS ACCESS CONTROL 16
2.2.1.5 TERMINATING A TRIGGERED ALARM 16
2.2.1.6 SECTION CONTROL BY AUTHORIZATION 17
2.2.1.7 SECTION CONTROL FROM THE KEYPAD’S MENU 17
2.2.2 OPERATING THE SYSTEM WITH A KEYFOB 17
2.2.3 OPERATING THE SYSTEM USING A COMPUTER (J-LINK) 18
2.3 REMOTE OPERATING 18
2.3.1 OPERATING THE SYSTEM USING THE MyJABLOTRON SMARTPHONE APP 19
2.3.2 OPERATING THE SYSTEM VIA THE MyJABLOTRON WEB INTERFACE 19
2.3.3 OPERATING THE SYSTEM USING THE VOICE MENU 19
2.3.4 OPERATING THE SYSTEM USING SMS COMMANDS 20
2.3.5 OPERATING THE SYSTEM REMOTELY USING A COMPUTER (J-LINK) 20
2.3.6 CONTROLLING THE PROGRAMMABLE OUTPUTS (PG) 20
2.3.6.1 KEYPAD SEGMENT 20
2.3.6.2 USER KEYPAD AUTHORIZATION 20
2.3.6.3 FROM THE MENU OF THE KEYPAD WITH AN LCD DISPLAY 20
2.3.6.4 REMOTE CONTROL 21
2.3.6.5 MyJABLOTRON SMARTPHONE APP 21
2.3.6.6 MyJABLOTRON WEB INTERFACE 21
2.3.6.7 DIALLING-IN 21
2.2.6.8 SMS MESSAGE 21
3. BLOCKING/DISABLING IN THE SYSTEM 21
3.1 BLOCKING USERS 21
3.2 BLOCKING DETECTORS 21
3.3 DISABLING TIMERS 22
4. CUSTOMIZING THE SYSTEM 22
4.1 CHANGING A USER ACCESS CODE 22
4.2 CHANGING, DELETING OR ADDING AN RFID CARD/TAG 22
4.3 CHANGING A USERNAME OR PHONE NUMBER 22
4.4 ADDING/DELETING A USER 22
4.5 CALENDAR EVENTS SET UP 23

2
5. EVENT HISTORY 23
5.1 USING THE LCD KEYPAD 23
5.2 USING THE J-LINK SOFTWARE AND A COMPUTER 23
5.3 LOGGING INTO MyJABLOTRON (WEB/SMARTPHONE) 23
6. PERIODICAL MAINTENANCE 24
7. TECHNICAL SPECIFICATIONS 25
8. GLOSSARY OF TERMS 26
TABLE OF CONTENTS

3
1. INTRODUCTION
Thank you for choosing the JABLOTRON 100+security system. This system
is a unique flexible indoor solution for commercial and home security that offers
the use of both wired and wireless devices. The JABLOTRON 100+is very easy
to control. Simplicity of control consists of two steps, authorization with a code
or a RFID tag followed by pressing an individual keypad segments with assigned
function on a keypad. It is possible to use a reversed method when the “Default”
system profile is enabled. Press a segment button first and then authorize.
The control segments use a simple traffic light logic which everyone can
understand. The number of segments can be promptly adapted to requirements
of premises. The JABLOTRON 100+series offers a wide range of detectors
with timeless design. It can be operated from anywhere owing to complete
remote control access. The MyJABLOTRON web interface, the MyJABLOTRON
application for smart phones and the J-Link software allow you to control,
program and monitor the system remotely.
The JABLOTRON 100+system is designed for up to 600 users and it can
be divided into 15 individual sections. Up to 230 devices can be connected and
the system offers up to 128 multi-purpose programmable outputs (e.g. home
automation).
The security system can be controlled in a number of different ways. To unset the alarm, authorization
in the form of user identification is always required. The system detects the identity of the users and allows
them to operate those parts of the system which they have been assigned to control. You can choose from
different ways of setting with or without authorization. When Standard authorization type is used, you don’t have
to authorize yourself because it is possible to set the system just by pressing the right segment button
on a keypad. The user name, date, and time are recorded and stored in the system memory every time
the system is accessed. This information is available indefinitely. Any user can also cancel a triggered alarm
(stop sirens from sounding) just by authorization in any part of the system (depending on their access rights).
However, that does not automatically unset the system (unless the system’s default setting is changed).
Note: Depending on the configuration of the installation and system settings, some of the options
described below may not be available. Consult the configuration of the installation with your service technician.
Users and their access rights
CODE
AUTHORIZATION
TYPE DESCRIPTION
ARC code This code has the highest level of authorization to configure the system’s behaviour and is exclusively
allowed to perform the system unblock after a triggered alarm. It can enter Service mode, access all tabs
with options including ARC communication to which it can deny access to a Service technician (Service
code). As long as the “Administrator-restricted Service/ARC right” parameter remains unchecked, the ARC
code can control all sections and PG outputs used in the system. This code enables to add more Administra-
tors and other users with a lower level of authorization, assign them with codes, RFID tags and cards.
It also has a permission to erase alarm and tamper alarm memory.
The number of ARC codes is limited only by remaining capacity of the control panel and there
is no code set by the factory defaults.
Service code
(Service)
This code can enter Service mode and configure the system’s behaviour. It has access to all tabs with
options including ARC communication unless the access is limited by the ARC technician. As long
as the “Administrator-restricted Service/ARC right” parameter remains unchecked, the Service code can
control all sections and PG outputs used in the system. It can create users with ARC permission, other
Service technicians, Administrators and other users with a lower level of authorization and assign them with
access codes, RFID tags and cards. It also has a permission to erase alarm and tamper alarm memory.
The number of Service codes is limited only by remaining capacity of the control panel.
By the factory defaults, the code is 1010. The Service user is always on position 0 in the control
panel and it cannot be erased.
2. OPERATING THE JABLOTRON 100+ SYSTEM

42. OPERATING THE JABLOTRON 100+ SYSTEM
CODE
AUTHORIZATION
TYPE DESCRIPTION
Administrator
code (Main)
his code has always full access to all sections and is authorized to control all PG outputs. The Administrator
can create other Administrator and other codes with a lower level of authorization and assign them with access
to sections and PG outputs, access codes, RFID chips and cards. This code has permission to erase the alarm
memory. There can be only one main Administrator code which can’t be erased. When “Administrator-restricted
Service/ARC right” is enabled, the administrator code must be authorized to confirm access for ARC and
Service technicians.
By the factory defaults, the code is 1234. The main Administrator user is always on position 1 and
it cannot be erased.
Administrator
code (Other)
This code has access to sections selected by the main Administrator to which the other Administrator can
add new users with the same or lower level of authorization to control sections and PG outputs, assign them
with access codes, RFID tags and cards. This code has permission to erase the alarm memory in assigned
sections. When “Administrator-restricted Service/ARC right” is enabled, the administrator code must
be authorized to confirm access for ARC and Service technicians.
The number of Administrator codes (other) is limited only by remaining capacity of the control panel.
There is no code set by the factory defaults.
User code This code has access to sections and PG control rights assigned by an Administrator. Users can add/delete their
RFID tags and access cards and change their own telephone numbers. Users can change their codes provided
that the system uses Codes with prefixes. It has permission to erase the alarm memory in assigned sections.
Selected users may have their access to sections limited by a schedule.
The number of User codes is limited only by remaining capacity of the control panel. There is no code set
by the factory defaults.
Set code This code is allowed only to set a designated section and is allowed to control (ON/OFF) PG outputs which
require authorization. Users with this level of authorization are not allowed to change their code and are not
allowed to erase the alarm memory.
The number of Set codes is limited only by remaining capacity of the control panel. There is no code
set by the factory defaults.
PG only code This code allows the user to control programmable outputs with authorization only. This applies to both
switching on and off. Users with this level of authorization are not allowed to change their code and are not
allowed to erase the alarm memory.
The number of PG only codes is limited only by remaining capacity of the control panel.
There is no code set by the factory defaults.
Panic code This code is allowed only to trigger Panic alarm. A user of this code is not allowed to change it or erase
the alarm memory.
The number of Panic codes is limited only by remaining capacity of the control panel. There is no code
set by the factory defaults.
Guard code This is a code for a security agency. This level of authorization allows to set the whole system. However, the guard
code can unset the system only during alarm or after it expired as long as the alarm memory is still active.
A user of this code is not allowed to change it or erase the alarm memory.
The number of Guard codes is limited only by remaining capacity of the control panel. There is no code
set by the factory defaults.
Unblocking code This code is designated to unblock the system after System blocking by alarm. A user of this code is not
allowed to change it or erase the alarm memory.
The number of Unblocking codes is limited only by remaining capacity of the control panel.
There is no code set by the factory defaults.
The security of access codes, contactless RFID devices and remote controls:
A control panel enables each user to be assigned with one 4, 6 or 8-digit code and up to two RFID tags
for system authorization. User authorization is required during each manipulation operation via keypad,
voice menu, a computer, web or mobile apps. Code length affects number of possible combinations and
therefore code security.

5
The number of code combinations depends on the configuration:
Ways to improve protection against guessing the valid code:
aUsing a code with more digits (6 or 8-digit codes),
aMore advanced types of authorization (such as “Card confirmation with a code”
or “Double authorization”).
Ways of operating the JABLOTRON 100+:
On-site:
aSystem keypad
aSystem keyfob
aComputer using a USB cable and the J-Link software
Remotely:
aMyJABLOTRON smartphone application
aComputer via the MyJABLOTRON web interface
aTelephone using the voice menu
aTelephone via SMS
aComputer via the internet using the J-Link software
aDialling-in from an authorized telephone number (only for operating programmable outputs)
2.1 ON-SITE OPERATING
2.1.1 USING THE SYSTEM KEYPAD
JABLOTRON 100+system may be controlled by a variety of access modules which let you not just
control but also display statuses of individual segments. The system can be operated directly (setting
or unsetting the system and other automation functions) using two-button segments on the keypad.
The segment buttons are clearly labelled and coloured (using traffic light logic) so that each segment status
is distinctly indicated. A segment can also be used to indicate a status (e.g. opened garage door)
or to control various automated devices (for example heating or window blinds). The maximum number
of segments is 20 for one access module. A segment can also be set up to call for help in an emergency
(medical or panic alarm).
Control panel parameters 4 DIGITS 6 DIGITS 8 DIGITS
“Code with a prefix” enabled = 104= (10.000) = 106= (1.000.000) = 108= (100.000.000)
“Code with a prefix”
and “Duress access control”
both disabled
= 104– (Number of users – 1) = 106– (Number of users – 1) = 108– (Number of users – 1)
“Code with a prefix” disabled;
“Duress access control”
enabled
≤ 104– ((Number of users – 1) * 3) ≤ 106– ((Number of users – 1) * 3) ≤ 108– ((Number of users – 1) * 3)
Using only an RFID card with
a range of 14 characters
(6 constant + 8 variable)
= 108= (100.000.000) = 108= (100.000.000) = 108= (100.000.000)
“Code with a prefix” and
“Card confirmation with
a code” both enabled
= ( 108* 104) = 1012 =
(1.000.000.000.000)
= (108* 106) = 1014 =
(100.000.000.000.000)
= (108* 108) = 1016 =
(1.000.000.000.000.000)
“Code with a prefix” disabled;
“Card confirmation with
a code” enabled
= 108 * (104– (Number of users
– 1))
= 108* (106– (Number of users
– 1))
= 108* (108– (Number of users
– 1))
2. OPERATING THE JABLOTRON 100+ SYSTEM

62. OPERATING THE JABLOTRON 100+ SYSTEM
The types of access modules and their combinations:
When unsetting the alarm using the segment buttons,
user authorization is always required. When setting the alarm
and controlling automated processes using the segment
buttons, user authorization is optional for each segment.
RFID card reader – allows control
of the system using segments and user
authorization using contactless method
(RFID card/tag).
Keypad with a card reader – the user
can control the system using segments
and authorization, either by entering
a code or the contactless method (RFID
card/tag), or a combination of both for
higher security.
Keypad with an LCD display and
a card reader – the user can control
the system using segments and authori-
zation, using either a code, the contact-
less method (RFID card/tag), both code
and card/tag for higher security,
or by authorizing and using the options
available on the keypad’s LCD display.
Continuous yellow
PARTIALLY SET
Flashes red
ALARM /
ALARM MEMORY
Continuous green
EVERYTHING OK
Flashes green
CONTROL
Flashes green 2x each 2 s
MAINTANENCE
Continuous yellow
FAULT
Flashes yellow
UNSUCCESSFUL SETTING
CARD READER / KEYPAD
Continuous red
SET / ON
Flashes red
ALARM /
ALARM MEMORY
Continuous green
UNSET / OFF
Flashes green
ENTRY DELAY

7
2. OPERATING THE JABLOTRON 100+ SYSTEM
Users can authorize themselves by entering their
assigned codes or using their RFID cards/tags.
Each user can have one code and up to two RFID chips
(cards or tags).
Recommended contactless chips: JABLOTRON 100+, Oasis or other third-party chips compatible with
125 kHz EM. If higher security is required the alarm system can be set up to use confirmed authorization
using RFID chips and codes (optional).
If the users want to control multiple segments simultaneously, they must authorize themselves and then
press segments of the particular sections subsequently. This way the users can for example set the house
and unset the garage within one single authorization.
If the “Code with a prefix” parameter is enabled, the keypad authorization code can consist
of up to eleven digits: a prefix (one to three digits), an asterisk * (which separates the prefix and main code),
and a 4,6 or 8-digit code depending on configuration (for example: 123*12345678, or 1*12345678). All users
can change their own codes which follow the prefix. The code can be changed from the keypad with the
LCD display, the J-Link software or MyJABLOTRON app.
If the “Code with a prefix” parameter is enabled, the users can be allowed to change their code.
If the “Code with a prefix” parameter is disabled, the codes can be changed only by the Administrator.
2.1.2 KEYPAD CODE AUTHORIZATION
Authorization with a user code is done by typing a valid code into a keypad or with an RFID tag.
It is possible to use 4, 6 or 8-digit codes in the system.
The system can be configured to be used with prefix codes or without them (default settings). For alarm
systems with a higher number of users the prefix can be enabled. To change this option please contact
the service technician of your alarm system.
Code without a prefix: cccc
where:
cccc is a 4, 6 or 8-digit code, allowed codes are from 0000 to 99999999
Default control panel code Administrator: 1234; 123456; 12345678;
Code with a prefix: nnn*cccc
here:
nnn is the prefix, which is the number of the user’s position (position 0 to 600)
*is a separator (key *)
cccc is a 4, 6 or 8-digit code, allowed codes are from 0000 to 99999999
Default control panel code Administrator: 1*1234; 1*123456; 1*12345678;
WARNING: The main Administrator code starts with the prefix 1
The main Service code starts with the prefix 0
To change the code type please contact the service technician of your alarm system.

82. OPERATING THE JABLOTRON 100+ SYSTEM
Structure and description of the internal LCD keypad menu
Cancel warning
indication
Section Control
PG control
Event memory
Setting
prevented
Faults in
system
Bypassed
detectors
System status
Settings
Display setting
Maintenance
mode
Allows you to cancel alarm/unsuccessful setting
indication in all sections to which the user has
access rights
Allows you to control the system‘s sections
to which the user has access rights and are
enabled in the internal settings.
Allows the user to control PG programmable
outputs depending on the user’s permissions and
according to the internal settings.
Displays a detailed list of the event memory.
Shows a list of triggered detectors preventing
setting the system, provided this option
is activated in the control panel configuration.
Displays a list of all detectors indicating
system faults from sections to which the user
has access rights.
Displays a list of all blocked detectors in sections
to which a user has access rights.
Shows system status (list of triggered detectors,
triggered tamper contacts, low batteries,
bypassing, etc.).
Allows editing of users and devices
(only when USB is disconnected).
Allows adjustment of keypad backlight intensity
and display contrast.
Allows the Administrator to switch assigned
sections to the Maintenance mode.
Administrator or
User authorization
by the code or RFID
tag/card

9
2.1.2.1 ALARM SETTING
While setting the alarm, if any detector is triggered (e.g. an open window) the system will react in one
of the following ways (based on the system configuration):
aDetectors will guard automatically after they switch to a standby mode (default setting).
aThe system will optically indicate triggered detectors with a segment flashing red for 8 seconds
and the system will set automatically once this period has expired.
aSetting the section with triggered detectors is also possible by pressing the segment button on the right
side repeatedly. This way a user confirms an intention to set the section with a triggered detector
(e.g. an opened window). Otherwise the section with the triggered detector will not be set.
aA triggered detector will prevent the section from being set. This status is optically indicated
by a flashing red segment button. The detector preventing setting will be shown in the menu
on the keypad’s LCD display.
An unsuccessful setting is indicated by the indication button flashing yellow (“Unsuccessful setting”
parameter must be enabled).
Consult the installation with a service technician in order to program the desired behaviour of the system.
2.1.2.2 ALARM UNSETTING
Note: If the “Unset section by authorization only during entrance delay” parameter is enabled, then mere
authorization will unset such section where the entrance delay has been triggered.
Consult the installation with a service technician in order to program the desired behaviour of the system.
1. Authorize using the keypad.
Sections which can be controlled
are lit up and the backlit indication
button will start flashing green.
2. Press the right button
(the one which isn’t lit up) to set
a particular section. It is possible
to set more sections subsequently.
The delay between sections
selection must not be longer than
2 seconds.
3. The command is executed
and the keypad acoustically indica-
tes the exit delay. The section is set
now, only the detectors with
a “Delayed Zone” reaction provide
time to leave the guarded area
during the exit delay. The segment
button of the set section turns red.
1. When you enter the building
(triggering a detector with
a “Delayed zone” reaction),
the system starts indicating entran-
ce delay with a continuous tone
and segment button of the section
in which the delayed entrance has
been triggered flashing green.
Authorize yourself using the
keypad – the green indication light
of the authorization panel starts
flashing.
2. Press the left segment button
of the section you want to unset.
3. The command is executed
and the segment buttons turn
green to indicate unset sections.
2. OPERATING THE JABLOTRON 100+ SYSTEM