jablotron MAESTRO JA-65 User manual

JA-65 “MAESTRO” Alarm system
Installation manual

This manual is valid for control panel model JA-65 versions FM61114 (control panel board) and DY6132 (telephone
communicator board).
The use of Comlink Windows v. 57 software or higher is required for this control panel and can be obtained from our home
page at www.jablotron.cz

Contents:
1. Architecture of the control panel 4
2. Configuration of t he control panel 5
3. Control panel installation 5
3.1. Power cable wiring 5
4. Antenna of the JA-65R module 5
4.1. Rubber antenna use in the control panel 5
4.2. External antenna use 6
5. Connection of a telephone line to the JA-65X module 6
6. Connectors and terminals of the main board 6
7. The JA-65H hard wired input module terminals 7
8. Wiring of the JA-60 keypad(s) 8
9. Installation of wireless items 8
10. Back up battery installation 8
11. First powering of the control panel 8
12. Control panel programming 9
12.1. Enrollment (teaching) of wireless items 10
12.2. Hard-wired zone input setting 11
12.3. Exit / Entrance delay 11
12.4. Alarm duration 11
12.5. PgX and PgY output functions 11
12.6. Recorded message and phone number editing in the user mode 12
12.7. Radio signal jamming testing 12
12.8. Regular communication checking 12
12.9. Reset enabled 12
12.10. Controlling of a subsystem sequence: 2 9 0 13
12.11. Enrollment of the control panel to a UC-2xx or to a master control panel 13
12.12 No code requested for F1, F2, F3, F4, F8 & F9 13
12.13. Partial (Home) arming with (F2) (non split control panel) 13
12.14. Hard wired siren alarm enabled 14
12.15. Exit delay audible indication 14
12.16. Partial arming exit delay audible indication 14
12.17. Entrance delay audible indication 14
12.18. Arming and disarming chirps with hard wired siren 14
12.19. Siren alarm in Disarm & Partial arming 14
12.20. Wireless siren alarm 15
12.21. Indication of system problems when arming 15
12.22. Control panel splitting 15
12.23. Only first source of alarm is recorded 15
12.24. Alarm triggered by opened zone when arming 15
12.23. Addressing of wireless detectors to sections 15
12.24. Addressing of the user codes to sections 16
12.25. Addressing of wireless controllers to sections 16
12.26. Automatic arming / disarming setting 16
12.27. New service code setting 16
12.28. User Mode entering 16
12.29. Real time and date setting 17
13. System testing 17
14. Voice & Pager message setting 18
14.1. Telephone number entering 18
14.2. Voice message(s) recording 19
14.3. Triggering of voice and pager messages sending 19
14.4. Dialing method 20
14.5. Telephone line checking 20
14.6. Telephone dialer testing 20
15. To enable a remote computer to dial in 21
15.1. Reaction to an incoming call 21
15.2. Remote access code setting 21
16. Monitoring station communication setting 22
16.1. Reporting code setting 22
16.2. Account code setting 23
12.3. Protocol and Format setting 23
16.4. Re-dialing pause setting 23
16.5. Phone number entering 24
16.6. Digital communicator reset 24
17. Control panel factory default reset 24
18. Monitoring station report code table 25
18.1. Internal structure of Contact ID protocol 26
19. Personal Computer Interface with PC-60A 27
20. Remote access to the system 28
20.1. Establishing connection with a remote control panel 28
21. Recommended Professional installer basic rules 28
22. Trouble shooting table 28
23. Possibilities to extend the system 29
24. Control panel specifications: 31

Alarm system JA-65 MAESTRO - 4 - MFM51210
This product is to be installed by professional installers only. The manufacturer assumes no liability for damages caused by incorrect
installation or improper use of this system.
1. Architecture of the control panel
The JA-65 "Maestro" is a fully programmable control panel with building block architecture. This allows the JA-65 to be
tailored to particular installation requirements. The Maestro can operate as a wireless, wired or combined system.
The JA-65K metal box has a built in electronic power supply. There is space for a 12V, 7Ah back up battery. The 16
zone control panel’s main board is installed in the internal platform. The main board does not have any physical zone
inputs. This allows you to co figurate the control panel by using the following modules:
•Radio communicating module JA-65R can enroll wireless items (JA-60): up to 16 detectors, up to 8 controllers
(remote controls or wireless keypads), JA-60A wireless sirens and UC family wireless output modules.
•Hard-wired input module JA-65H has 8 input loops with programmable triggering (NC, balanced or double balanced)
and programmable reactions. Up to two JA-65H hard-wired input modules can be used in the control panel.
•GSM dialer JA-60GSM sends SMS messages, calls to predefined telephone numbers and plays audible warning,
communicates with 2 CMS, allows remote access from a phone’s keypad and can be set via web page.
•Telephone communicator JA-65X can communicate with a Monitoring Station, send voice messages and dial a
numeric Pager. It can also communicate with a remote PC (using ComLink SW and a JA-60U modem).
•Operation and programming is possible via the JA-60E keypad (or by its wireless option, JA-60F). The control
panel can also be operated by a RC-11, RC-22 or RC-60 remote control, by input loop or by a JA-60D wireless
keypad. Operation and programming is also possible via a PC using ComLink SW.
This allows the JA-65 to operate as a wireless (16 detectors), wired (8 or 16 inputs) or combined system. An additional
JA-60 or JA-65 subsystem control panel can expand the system. The control panel can be split in to two independent
sections with a shared common area.

Alarm system JA-65 MAESTRO - 5 - MFM51210
2. Configuration of the control panel
The metal case of the JA-65K control panel is shipped from the factory with a built-in power supply unit and the main board. To
be able to work as an alarm system, it should be equipped with interface modules (R, H, X) in the following way:
•open the case and remove the cover
•disconnect the power unit cable from the main board connector K5
•unscrew the module platform (screw on the left side)
•open the platform and remove it from the case
•attach the desired modules to the positions shown in the previous diagram
•connect the modules' cables to the main board in the following way:
o60GSM or 65X = K1
o65R = K2
o65H = K3 (if two 65H modules are used, connect the left module cable to the right 65H
module and the right module cable to the main board's K3 connector)
3. Control panel installation
The control panel’s case is designed to be attached to the wall, or it can be partly installed into the wall. The rectangular
hole on the back side is for cable routing. The hole matches a KT-250 standard junction box. This allows for easy
specification on how to prepare cables in a house before an alarm system installation.
•If the 65R radio-communicating module is used, keep in mind that the antenna will need about 20 cm of
clearance. The 65R module comes with a rubber antenna, but it can also be used with an external antenna,
model AN-01. The working range of the wireless accessories is about 100 meters under optimal conditions.
However, building materials can absorb or obstruct radio signals and communication can also be effected by
interference from other radio signals. For these reasons, you should anticipate a shorter working range for indoor
installations.
•Before attaching the case to the wall, remove the power supply unit (two screws from the front side)
•Route all the cables to the control panel (power, input loops, outputs, telephone line etc.) before you attach
the case to the desired location.
Note: if you install the case in the wall, the hinges for both the cover & module mounting platform should not be placed within the wall.
3.1. Power cable wiring
The power cable should be connected only by a licensed electrician. The control panel is a class II. device with
double insulation and power to its power unit must be wired with double insulated two core power cord. No power wire
should be connected to the metal case. Instructions:
•use flexible 2 core (size from 0.75 to 1.5 mm2) double insulated power cord.
The system should not share a fuse (10 A max) with any other household
item. The fuse is used as a circuit breaker too.
•route the power cable through the plastic bushing of the power supply unit
cover and screw its wires tightly to the AC terminals
•attach the cable firmly to the board using the plastic bracket. Before you
tighten the bracket, check that the wires are tightly screwed in the terminals
and be sure that the wires are not longer than shown in the diagram.
•reattach the power supply unit in the case, but do not switch the power on
•install the module mounting platform to the case and connect the power unit
cable to connector K5 on the main board .
Warning: never open the cover of the power supply unit when the system is powered!
4. Antenna of the JA-65R module
If the JA-65R module is installed, it will be possible to enroll wireless detectors,
controllers, a JA-60A siren, output modules and another wireless subsystem if
required. Enrollment is described in the part 9. The 65R module must be equipped
with an antenna.
4.1 Rubber antenna use in the control panel
There is a hole on the top of the control panel case (remove the plastic cap) for the
rubber antenna. The rubber antenna is supplied with the 65R module. Install the
antenna after the module mounting platform is inserted and screwed inside the
control panel case. Attach the antenna to the 65R board using a screw as shown in
the diagram. The antenna must not be obstructed by any large metal object.

Alarm system JA-65 MAESTRO - 6 - MFM51210
4.2 External antenna use
An optional external antenna, model AN-01, can be used with the 65R module. This antenna has a connector, which fits
the connector on the 65R module. If you use the external antenna, the rubber antenna should not be installed. The AN-01
antenna has a small plastic ring on its end, used to hang it from the wall. Its active part (from the plastic ring to the coil)
should be installed vertically and should not be obstructed by any large metal object. The antenna can be located behind
furniture, etc.
5. Connection of a telephone line to the JA-65X module
If the JA-65X module is installed, the control panel can communicate with a
Monitoring Station, send voice messages and dial a numeric Pager as well as
communicate with a remote PC. A standard analog telephone line (type TNV 1-3)
must be connected to the 65X module for these functions.
•Use the provided telephone cable to connect the telephone line to the IN
jack in the 65X module (see diagram )
•Connect a telephone, fax or other phone operated device to the OUT jack,
marked with a phone symbol
•When the control panel is in normal stand by mode, the phone line and any
attached device will operate as normal
Note: The communicator must be plugged directly to a telephone line socket. All other
devices (telephone, facsimile machine, modem etc.) should be connected to the
communicator output.
6. Connectors and terminals of the main board
In addition to the interface module connectors (K1, K2 and K3) the main board has the following connectors:
K5 - power supply connector: the cable from the power unit is connected to this . By disconnecting this cable you
completely power-down the system (for example, when you perform a factory default reset).
K4, K6 - digital data jacks for the JA-60E keypad(s) and/or for a PC interface cable. Up to five JA-60E keypads can
be connected to a JA-65 and the maximum length of the cable can be 500 meters. We recommend use of a CT-04 cable
and RJ-44 (Jablotron) crimping connectors to make the keypad cables. The digital data is also available on the terminals:
see the following description.
1,2,3,4 - digital data terminals (see K4, K6) provide an option to use standard cable for the wiring of JA-60E keypads. The
keypads are also equipped with both jacks and terminals.
The following terminals are on the bottom side of the main board:
TMP a pair of terminals to connect the tamper switch of an external device (for example: a wire operated outdoor siren,
OS-300). In normal use, these terminals should be connected together via a 2k2 resistor. Triggering of this loop has
the same effect as control panel tampering (a change of ±30% or more of the End Of Line resistor will trigger the input).
PGX is an output (transistor switching to GND, max. 12V, 100mA). The function of this output is determined by the setting in
the programming mode (see 12.5). The control panel also wirelessly transmits the PGX signal and unit UC-216 or
UC-222 can be used as a remote output of this signal.
PGY is an output (transistor switching to GND, max. 12V, 100mA). The function of this output is determined by the setting in
the programming mode (see 12.5). The control panel also wirelessly transmits the PGY signal and unit UC-216 can
be used as a remote output of this signal.
Cis a common contact of the alarm output relay, max. load 60V / 1A. The relay is turned on during any alarm of the
control panel.
NC is a normally closed contact of the alarm output relay.
NO is a normally open contact of the alarm output relay.
GND is a common ground terminal of the power output (-). This terminal is also available on 65H modules.
SIR is an external siren output. In the normal mode it has the +U terminal voltage. In the alarm mode it has a GND terminal
potential. Connect an ordinary external siren to +U and SIR terminals (max. load 0,7 A). A back up siren charging input
should be connected to the GND and the SIR terminals (during an alarm, the charging will temporarily halt). The siren
can also be used for sounding arming and disarming chirps and as an audible indicator while in the testing mode.
+U is a back up power output for external items (detectors etc.). The max. permanent current is 0.7 or 1.2 A for max. 15
min (not more then one cycle per hour). This output is fused and supervised by the control panel. If it is overloaded, a
control panel failure will be indicated (fault C). The multiple +U terminals are also available on the JA-65H hard-wire
modules for easier wiring. All +U terminals are connected in parallel to the +U terminal of the main board.

Alarm system JA-65 MAESTRO - 7 - MFM51210
7. The JA-65H hard wired input module terminals
Up to two 65H modules can be used in the control panel. The module with its cable connected directly to the main board
provides zone inputs 1 to 8. If the second module is installed it will provide zone inputs 9 to 16. The 65H module has the
following terminals:
1 to 8 zone inputs – Normally, detector outputs are wired here: see examples of wiring in diagram. For each input it is
possible to program its method of triggering: Normally Closed loop, balanced loop (10k) or double balanced loop
(2x 10k) and the type of reaction of the system (see section 12).
COM Four common terminals to close (balance) the input loops
GND ground (negative pole) of the power supplier
+U backup power output for external devices (detectors etc.), max. total consumption form all +U terminals in the control
panel can be 0,7 A.

Alarm system JA-65 MAESTRO - 8 - MFM51210
8. Wiring of the JA-60 keypad(s)
The system can be programmed and operated by JA-60E keypad(s). As a maximum, 5 keypads can be wired to the
control panel. The keypads can either be wired by cables equipped with modular jacks to connectors K4 and K5 or by
standard cables to terminals 1,2.3 & 4 on the main control panel board. The same numbered terminals (pins in the
connectors) must be linked together. It is possible to combine arbitrary wiring with modular connectors and ordinary
cables - see diagram.
When a control panel has a JA-65R radio communicating module installed, it can also be operated and programmed
via JA-60F wireless keypad(s) asunder this situation, a minimum of one JA-60E keypad should be connected to the
control panel. With a 65R module, the system can also be operated by remote controls RC-11, RC-22 & RC-60, as well
as by a JA-60D wireless keypad. The control panel can have up to 8 wireless controllers.
It is also possible to operate and program the JA-65 system via a connected PC with SW ComLink. The PC can be
connected locally with a PC-60A interface cable or remotely, using a JA-60U modem (see section 19 and 20).
9. Installation of wireless items
If the control panel is equipped with a JA-65R module, it can work with all types of JA-60 wireless items and wireless UC
output modules (see brief overview of items in section 25.1).
•Detectors - one wireless JA-60 detector can be enrolled to each control panel zone (i.e. up to 16 detector)
•Keypads and remote controls - up to 8 wireless controllers can be enrolled to the control panel (JA-60F and JA-60D
keypads, RC-11 and RC-22 remote controls)
•JA-60A Wireless siren - only one can be enrolled to a control panel – position A (next JA-60A can be enrolled to detectors
positions)
•wireless output modules UC-216 and UC-222 have relays, which copy the status of the control panel’s programmable
outputs PgX and Pg Y. An unlimited number of the UC modules can be used with each system.
Follow the particular wireless item manual when installing. After you install the item to desired location, leave it un
powered and without its cover. The method of enrollment is described in section 12.1.
10. Back up battery installation
there is a space for size 12V, 7Ah battery. According to the desired backup period a 12V back up battery from 1.3Ah to
45Ah can be used instead. A battery larger than 7Ah must be installed in an external case and the case must be
equipped with tamper protection.
The control panel recharges and checks the condition of the back up battery. If the system is powered from the battery
for a long time and the battery is nearly discharged, the control panel will first trigger a technical alarm and it will then
disconnect the battery to prevent damage. After the main power is on again, the
battery will be re-connected and will automatically re-charge.
•insert the battery into the control panel
•connect the battery cables (red +, black - )
Warning - do not make any short connection of the battery terminals!
11. First powering of the control panel
•Check that all cables are connected correctly
•Switch on the AC power
For battery back up time calculation use the
following stand-by consumption rates:
module JA-65R 20mA
module JA-65X 12mA
module JA-65H 15mA
main b. JA-65K 10mA
keypad JA-60E 25mA

Alarm system JA-65 MAESTRO - 9 - MFM51210
•The keypad will display a "P", confirming that the system is in the programming mode (for system setting, enrollment of
wireless items and for testing).
Note: if „P“ is not displayed, the control panel is not in the factory default setting. Perform a Factory default reset. (See section 17).
12. Control panel programming
Functions of the system can be customized. The most convenient programming method is via a connected PC using the Comlink
software (see 19). Programming can also be performed by entering programming sequences from the system keypad while in the
programming mode:
•If the control panel is not in the programming mode, open it (entering F 0 SC - SC = Service Code, factory default SC=6060) –
The programming mode will be indicated by a „P“ on the LED display. This mode can only be entered when the panel is
disarmed. In this mode, no alarm can be triggered. Detectors and other accessories can be enrolled, the system parameters
can be set up and the system can be tested.
•The parameters of the control panel can be set by entering programming sequences from the keypad. Any unfinished
programming sequence can be terminated by pressing the Nkey.
•To exit the programming mode, press the N key („P“ will turn off). If any fault is indicated when you try to exit the
programming mode, the control panel will inform you of the problem (see programming sequence 39x for more details).
List of control panel programmable parameters
Function sequence options factory d. note
Enrolling of detectors and controllers 1 1& 7scroll, 2 erase pos., 3
controllers, 4 all - w. Rmodule only
Hard-wired zone input setting 60 nn xyz nn– zone n., x– triggering,
y– reaction, s- section all off w. Hmodule only
Exit / Entrance delay 21x x= 1 to 9 (x 10sec.) 30sec.
Alarm duration 22x x = 1 to 8 (min.), 0=10s, 9=15min 4min.
Function of PgX output 23x x= 0 to 8 (0-Chime, 1-Fire, 2-
Arm, 3-Panik, 4-Alarm, 5-Door,
6-Home, 7-No AC, 8-Phone
Chime split system has
different setting
Function of PgY output 24x x= 0 to 8 (0-Chime, 1-Fire, 2-
Arm, 3-Panik, 4-Alarm, 5-Door,
6-Home, 7-No AC, 8-Phone
Arm split system has
different setting
Voice m. & tel. Numbers editable in the user mode 25x 251 = YES 250 = NO NO w. Xmodule only
Radio signal jamming regular testing 26x 261 = YES 260 = NO NO w. Rmodule only
Regular communication check enabled 27x 271 = YES 270 = NO NE w. Rmodule only
RESET enabled 28x 281 = YES 280 = NO YES
Subsystem arming enrollment 290 will enroll to sub-control panel as wireless controller w. Rmodule only
Control panel enrollment to a UC-2xx, subsystem,... 299 will send enrolling signal w. Rmodule only
No code requested (effects , , , F4, F8 & F9) 30x 301 = YES 300 = NO YES
Partial (Home) arming enabled ( ) 31x 311 = YES 310 = NO YES
Siren alarm enabled 32x 321 = YES 320 = NO YES
Exit delay audible indication enabled 33x 331 = YES 330 = NO YES
Partial arming exit delay audible indication 34x 341 = YES 340 = NO NO
Entrance delay audible indication enabled 35x 351 = YES 350 = NO YES
Arming & disarming chirp sounds enabled 36x 361 = YES 360 = NO NO
Siren in Disarm & Partial arming enabled 37x 371 = YES 370 = NO YES
Wireless siren alarm enabled 38x 381 = YES 380 = NO YES w. Rmodule only
Indication of system problems when arming 39x 391 = YES 390 = NO NO
Split control panel (A, B & C sections) 690x 6901 = YES 6900 = N0 NO
Only first source of alarm is recorded 691x 6901 = YES 6910 = NO NO
Alarm triggered by opened zone when arming 692x 6921 = YES 6920 = NO NO only if 391
Addressing of wireless controllers to sections 63 nns nn– controller n., s- section all A split & R module
Automatic arming/disarming setting 64nahhmm n- 0-9, a-action #, hh-hours,
mm-min. all off split & partial arming see 12.21
New Service Code setting 5 nSC nSC nSC = new Service Code 6060 enter code twice
Real time and date setting 4 hh mm DD MM RR 00 00 01 01 00
User Mode entering 6999 Switching to the User mode -

Alarm system JA-65 MAESTRO - 10 - MFM51210
12.1. Enrollment (teaching) of wireless items enter: 1
If the control panel has a 65R module, as a maximum 16 wireless detectors and 8 controllers (remote controls & keypads)
can be enrolled to the control panel. A wireless siren and an additional JA-60 or JA-65 control panel (a subsystem) can be
enrolled as well.
•press key 1(while „P“ is displayed) to enter the enrolling mode. The control panel will display the next free position
to enroll a detector.
•Use key 1 and 6 to scroll (up and down) all control panel wireless positions – 1 to 16 (detectors) – c1 to c8
(controllers & keypads) – A (wireless siren) – J (sub control panel JA-6x). The display shows the position number
while the Battery LED indicates if the position is occupied.
•Detectors and keypads are automatically enrolled when their power is switched on (batteries are installed). A
remote control is enrolled only after both of its buttons are simultaneously pressed and held for 3 seconds. A
subsystem control panel will enroll after sequence 299 is entered while it is in its programming mode. The system will
not allow enrollment of an item into a non-corresponding position (a detector can not be enrolled into a controller
position etc.).
•Control panel confirms enrollment with a „beep“ (press F to select a louder “beep” sound). The LED display will
show the number of the enrolled item for 2 seconds and then it will display the number of the next free position.
•To change the position of an enrolled item is simple. Enroll it to the new selected position (the item will „move“).
If you enroll an item to an occupied position, the former item will be deleted and only the new enrollment is valid. Only
one item (detector, controller etc.) can be stored to each position.
•Erase an enrolled item the following way: in the enrolling mode select the corresponding position and then press
and hold key 2 for two seconds. The item will be erased (confirmed with a long beep). If you press and hold key 3, all
enrolled controllers (remote controls and keypads) will be erased. Pressing and holding key 4 will erase all enrolled
items (detectors, controllers, siren and the sub system).
•The JA-60A wireless siren will generate an enrollment signal when its power is switched on (it will enroll to
position A). If you need to enroll a siren which is already powered and it is not possible to easily switch off its power,
you can enroll it the following way: enter the enrolling mode and then enter the 6 digit siren production code (printed
in the siren’s manual). The control panel will “request” the siren to send its enrollment signal. The siren will send the
signal only if it has no current communication with any other control panel (This protects you from enrolling your
neighbor’s siren). Enrollment is completed about five seconds after the code is entered.
•By pressing the button 8 in the enrolment mode the communication quality of the items can be checked (LED
indicator “battery” will start flashing). After receiving signal from the item the level of the signal is shown on the
display from 0 to 10 (corresponding to 0-100% in the ComLink software). In this mode it is also possible to adjust
level of audible indications by pressing the button F and scroll positions of the enrolled items by pressing buttons 1
and 7. Button N exits checking mode.
•To exit the enrolling mode press the Nkey
Note: If you do not use JA-60E in your installation, you can enter the learning mode in a different way. Shorten the RESET pins
No.K11. This way the JA-60F keypad will be enrolled to the system. You can remove the jumper now.
Note: if an item was not enrolled after its batteries were installed, it is because the control panel recognized its radio signal as a weak
one. Items are only enrolled if their radio signal has a level which guarantees reliable communication. Check the detector’s batteries
and try to enroll the problematic sensor once more. If it is not accepted by the control panel, you should change the location of the item.
All items should be located 1 m or more from the control panel.

Alarm system JA-65 MAESTRO - 11 - MFM51210
12.2. Hard-wired zone input setting sequence: 60 nn xys
If there is a 65H module in the control panel, wire operated detectors can be connected to the control panel. Setting of the
zone inputs is possible by entering:
60 nn xys
where: nn = zone number: 01 to 16
x= input triggering: 0 = off, 1 = Normally Closed, 2 = balanced loop (EOL resistor 10 kΩ), 3 = double
balanced loop (EOL resistors 2x10 kΩ)
y= reaction: 0 = Instant, 1 = Delayed, 2 = Fire, 3 = Panic, 4 = Tamper, 5 = Next delayed, 6 = control
s= address to section, 1 = A, 2 = B, 3 = C (shared common section, which is armed only if both A and B
sections are armed). If the control panel is not split, select s=1; if you select s=2 then this zone will be
automatically bypassed within partial arming. For details about splitting see section 12.22.
Notes:
•If you will not use a particular input, switch it off with x = 0
•Next delayed input (y=5) provides entrance delay only if in the moment of its triggering the entrance delay has been in progress
(activated before by any delayed input). If no delayed input is triggered before next delayed, the triggering will cause instant alarm.
•Addressing of inputs to section C when the control panel is not split has the same effect as addressing to B section (i.e. automatic
bypass while partial arming is used).
•If y=6 is programmed, then each triggering of this input changes arming status (arm – disarm – arm…) of the entire system or just
the corresponding section if the system is split.
Example: to set zone 2 input as a balanced loop with an instant reaction, addressed to A section, enter: 60 02 201
Factory default setting: all hard-wired inputs are switched off.
12.3. Exit / Entrance delay sequence: 2 1 x
To change the duration of the exit and entrance delay (both of them) enter 21x (where xrepresents time in seconds x10).
The delay can be selected from 10 to 90 seconds.
Example: to select an Exit and Entrance delay duration of 20 seconds, enter 212
Factory default setting: 30 seconds
12.4. Alarm duration sequence: 2 2 x
The alarm duration can be selected from 1 to 8 minutes (or 10 seconds or 15 minutes) entering 22x (where xrepresents
time in minutes, for x=0 the duration will be 10 seconds, for x=9 the duration will be 15 minutes).
Example: to select an alarm duration of 5 minutes, enter 225
Factory default setting: 4 minutes
12.5. PgX and PgY output functions sequences: 2 3 x & 2 4 x
The control panel outputs PgX and PgY can have different functions, depending on parameter xin the corresponding
sequence:
2 3 x – determines triggering of PgX
2 4 x – determines triggering of PgY
where x represents the following functions (non split system):
0 Chime – triggered during the entrance delay (pre-alarm output)
1 Fire – triggered by a fire alarm (by a smoke or a gas detector)
2 Arm – activated when the control panel is armed (complete & partial arming)
3 Panic – activated when a silent panic alarm is triggered
4 Alarm – triggered by any audible alarm (except panic alarm)
5 Door – activated for 5sec. after (F3) entering (electric door lock opening)
6 Home – activated when the control panel is partially armed (Home arming)
7 No AC – triggered by an AC power failure
8 Phone/F8 – output can be operated remotely by phone or by SMS (if this feature is supported by installed
communicator) or locally from the keypad by F81 (ON) and F80 (OFF). If a code is requested to operate the system
then the F8x instruction should be followed by a valid user code.
Example: the PgX will work as a Panic output when 233 is entered, PgY as Door output when 245 is entered.
Factory default setting: PgX=Chime, PgY=Arm
Note: the control panel also wirelessly transmits the PgX and PgY signals. Wireless output modules UC-216 and UC-222 can be used
to receive the signals (see 25.1.). The function of the UC module output relays is determined by the 23x and 24x setting.
If the system is split:
x 23x (PgX) 24x (PgY)
0 Alarm A Alarm A
1 Alarm B Alarm B
2 Chime A Chime A
3 Chime B Chime B
4 Arm A Arm B
5 Door A Door B
6 Panic A Panic B
7 FIRE NoAC
8 Phone Phone

Alarm system JA-65 MAESTRO - 12 - MFM51210
12.6. Recorded message and phone number editing in the user mode sequence: 2 5 x
The User mode, which is accessible with F 0 “Master Code”, is for bypass setting, system testing and battery replacement.
This setting enables the user to change the voice message and telephone numbers of the built in dialer. If the changes are
enabled, then programming sequences for number programming, voice message recording and dialer testing are accessible
in the User mode. These settings have effect only when the control panel has a 65X communicator module.
options: 2 5 1 changes enabled
2 5 0 changes disabled (no dialer programming in the User mode)
Factory default setting: changes disabled
12.7. Radio signal jamming testing sequence: 2 6 x
When this function is enabled, the control panel will indicate trouble if the working band is jammed for more than 30
seconds. Jamming will trigger an alarm when the control panel is armed. Do not enable this testing, if the control panel
does not have a 65R radio module.
options: 2 6 1 testing enabled
2 6 0 testing disabled
Factory default setting: disabled
Note: in some locations the system can be repeatedly jammed for some period of time (near radar, TV or radio station etc.). In these
cases the control panel can work without any problems because all important data is repeated, but the jamming test should not be
enabled. The level of the signals and interference can be observed using the Comlink software (see 19.)
12.8. Regular communication checking sequence: 2 7 x
The control panel will check communication regularly with all enrolled items (detectors, keypads, siren etc.) when this
function is enabled. If communication is lost with any item, the control panel will indicate the fault of this item (when armed
it will also trigger an alarm). Do not enable this checking, if the control panel does not have the 65R radio module.
options: 2 7 1 checking enabled
2 7 0 checking disabled
Factory default setting: checking disabled
Note: in some locations with a strong radio interference (near radar, TV or radio station etc.) the communication can be jammed periodically.
The control panel can detect such a strong interference as a temporary loss of communication with an item. Even in this case, the system is
usually able to work without any problems, because all important data is repeated, but the communication check should not be used.
12.9. Reset enabled sequence: 2 8 x
The factory default reset (see 17.) can be disabled. This way no unauthorized future programming of the control panel will
be possible.
options: 2 8 1 reset enabled
2 8 0 reset disabled
Factory default setting: reset enabled
Note: if the Master or Service code is forgotten when the reset is disabled, the reset of the control panel will be possible only by the
manufacturer.

Alarm system JA-65 MAESTRO - 13 - MFM51210
12.10. Controlling of a subsystem sequence: 2 9 0
A wireless master control panel receives event signals (alarms, tampering, faults, low battery) from a JA-6x subsystem if
enrolled - see 12.1 and 12.11. This will cause the same kind of event on the master control panel and Jwill be indicated
as the source of the event on the keypad.
The master and slave control panels can be either armed and disarmed as two independent systems or the slave system
can follow the arming and disarming of the master. If the master should rule arming of the slave subsystem, make the
following settings:
a. enroll a subsystem to the master‘s J position,
b. place the master panel into the programming mode (P is indicated),
c. enter the enrolling mode in the sub-control panel (pressing key 1 while in the programming mode)
d. enter 290 on the master control panel – this way the master will be enrolled to the slave sub-control panel as a
wireless controller (to the first free position of c1 to c8)
e. turn both systems to standby mode and check that the subsystem will be armed (in 2 seconds) after arming of
the master control panel. Check the same for disarming
Notes:
•Master control panel generates wireless commands Arm and Disarm the same way as a remote control RC-11. The control
panel transmits these commands only if it has a subsystem enrolled in its position J.
•The Arm command is generated when the master control panel is completely armed and also at the end of an alarm while
the system remains completely armed (automatic alarm timeout). The Disarm command is generated when the master
control panel is disarmed, when it is partly armed (home arming or one section arming if it is split) and also in the end of an
alarm while the system is disarmed (manual termination of the alarm).
•The subsystem can also be operated by its other controllers (remote controls, keypads) if there are any. For better
understanding you can simply imagine, that the master control panel is just another remote control.
Controlling of the subsystem by the master control panel can be disabled by erasing the corresponding cN position in
the sub-control panel. For example if the master control panel was enrolled to position c3, scroll to this position in the
enrolling mode and holding key 2 will erase the master control panel as a controller.
12.11. Enrollment of the control panel to a UC-2xx or to a master control panel sequence: 2 9 9
The control panel can send wireless data to output modules UC–216, UC–222 and UC-260 (see section 24.). It can also
work as a subsystem of another JA-65 or JA-60 control panel.
Enter the enrolling mode of the UC receiving device and then enter 299 and the control panel will transmit the enrollment
signal.
If you want to enroll a subsystem to your control panel, enter the enrolling mode on the MASTER control panel (see
12.1.) and then enter sequence 299 in the programming mode of the sub control panel.
If the system is split the sub control panel enrolls to the common shared section.
12.12 No code requested for , , , (F1, F2, F3), F4, F8 & F9 sequence: 3 0 x
If this parameter is enabled no code is requested for functions F1, F2, F3, F4, F8 and F9 (or the , , keys on
the keypad). When this parameter is disabled these functions (keys) can be used only when followed by a code (Master
or User) – see the following table:
Factory default setting: no code requested
Note: this feature is also selectable on the JA-60D wireless keypad and it is
independent from the control panel setting.
„code“ = Master or User
12.13. Partial (Home) arming with (F2) (non split control panel) sequence: 3 1 x
In partial arming, the control panel reacts only to detectors addressed to section A (see 12.2 and 12.23) and it ignores the
triggering of detectors in section B or C (except smoke and gas detectors). Partial arming can be disabled with this sequence.
options: 3 1 1 partial arming enabled
3 1 0 partial arming disabled
Factory default setting: partial arming enabled
function / setting 300 301
arming „code“ F 1
partial arming F 2 „code“ F 2
door opening F 3 „code“ F 3
memory reading F 4 „code“ F 4
Appliance control F 8 „code“ 0
F 8 „code“ 1 F 80 F 81
message listening F 9 „code“ F 9

Alarm system JA-65 MAESTRO - 14 - MFM51210
12.14. Hard wired siren alarm enabled sequence: 3 2 x
The SIR siren output is activated when any alarm is triggered (except silent Panic alarm). The siren indication can be
disabled with this parameter.
options: 3 2 1 siren enabled
3 2 0 siren disabled
Factory default setting: siren enabled
12.15. Exit delay audible indication sequence: 3 3 x
The exit delay can be indicated by the „beeping“ of the keypad (for the last five seconds, the beeping is faster). The
audible indication can be disabled with this setting.
options: 3 3 1 indication enabled
3 3 0 indication disabled
Factory default setting: indication enabled
12.16. Partial arming exit delay audible indication sequence: 3 4 x
Partial arming with (F2) provides an exit delay for delayed reaction detectors in section A. The exit delay for partial
arming can be indicated by the „beeping“ of the keypad (for the last five seconds the beeping is faster).
options: 3 4 1 indication enabled
3 4 0 indication disabled
Factory default setting: indication disabled
Note: when this indication is disabled, the confirmation of partial arming and disarming will automatically be silent, regardless of the
36x setting.
12.17. Entrance delay audible indication sequence: 3 5 x
The entrance delay can be indicated by a rapid „beeping“ of the keypad. This indication can be disabled with this setting.
options: 3 5 1 indication enabled
3 5 0 indication disabled
Factory default setting: indication enabled
12.18. Arming and disarming chirps with hard wired siren sequence: 3 6 x
The control panel can confirm on the SIR output arming (1 chirp), disarming (2 chirps), disarming with information in the
memory (3 chirps), bypass or not ready component when arming (4 chirps). This parameter sets chirps on.
options: 3 6 1 siren chirps enabled
3 6 0 siren chirps disabled
Factory default setting: siren chirps disabled
Note: setting of chirp sounds is valid even if the siren is disabled for alarms with parameter 320. Partial arming is always silent, if sequence
340 is selected. Chirp sounds can also be generated with the JA-60A wireless siren (self-contained setting in the wireless siren).
12.19. Siren alarm in Disarm & Partial arming sequence: 3 7 x
The SIR output can be disabled for alarms during the Disarm & Partial arming of the control panel (while somebody is
indoors). If the siren output is completely disabled for alarms with parameter 320, this setting has no effect.
options: 3 7 1 alarm in disarm & partial arming enabled
3 7 0 alarm in disarm & partial arming disabled
Factory default setting: enabled

Alarm system JA-65 MAESTRO - 15 - MFM51210
12.20. Wireless siren alarm sequence: 3 8 x
The wireless siren alarm function can be disabled with this parameter. This setting will have no influence on the outdoor
wireless siren chirp sound function if enabled in the siren. This setting has effect only when the control panel is equipped
with a 65R module:
options: 3 8 1 siren enabled
3 8 0 siren disabled
Factory default setting: siren enabled
12.21. Indication of system problems when arming sequence: 3 9 x
The system regularly checks the conditions of all items (detectors, keypads etc.). This setting ensures that the user will be
warned with 4 rapid beeps after arming, if any component of the system is not ready for arming. Cause of the problem (for
example permanently triggered detector, lost communication etc.) will remain displayed on the keypad. If the user ignores
this warning, the system will arm after the exit delay, then an alarm will be triggered and finally the problematic item will
be bypassed for this arming period. After disarming in such a mode, three beeps will be generated as well.
When the indication is not selected, the problematic item will be bypassed when arming with neither warning nor alarm.
If a permanently activated detector is deactivated during arming (for example your main door is not closed), the bypass of
this detector will be canceled automatically and the detector will be ready to trigger an alarm after it is activated (if you
close the door after the system is armed).
options: 3 9 1 warning enabled
3 9 0 warning disabled
Factory default setting: warning disabled
Note: if this indication is enabled, the problems will also be indicated if there are any when leaving the programming or user mode.
12.22. Control panel splitting sequence: 690 x
The control panel can be split in to 2 independent sections A and B, with a shared common area C. This way the system
can be operated by two independent user groups. In fact the system in this mode works like two independent systems. If
the system is split to the sections with this setting, it is possible to address detectors (both wireless and wired), user
codes and remote controls to the above sections (see 12.2., 12.23 and 12.24.).
options: 6 9 0 0 no splitting (partial arming available in this mode)
6 9 0 1 splitting to sections A, B and common C (C is armed only when both A and B are armed)
Factory default setting: no splitting
12.23. Only first source of alarm is recorded sequence: 691 x
When any item triggers the alarm 4 times in a row the system will bypass it until any other events occurs. But it is
possible to set the limit at the incoming events so only the very first event during the entire alarm will be recorded. This
function is useful especially if the system contains a GSM communicator in order to decrease quantity of the SMS
messages. This setting is valid for all kinds of the alarm.
Options: 6 9 1 0 All sources of alarm are recorded
6 9 1 1 Only first source of alarm is recorded
Factory default setting: All sources of alarm are recorded
12.24. Alarm triggered by opened zone when arming sequence: 692 x
If the “indication of system problems when arming” (see 10.21) is enabled, it is also possible to test the status of the
detectors after expiring the exit delay. If any item is activated then in case of instant zone the alarm will be triggered
immediately, in case of delay zone the entry delay will start.
Options: 6 9 2 0 test disable
6 9 2 1 test enable
Factory default setting: test disabled

Alarm system JA-65 MAESTRO - 16 - MFM51210
actions' table
a no splitting split system
0 no action no action
1 arm all arm all
2 disarm disarm all
3 partial arming arm A
4 partial arming arm B
5 disarm disarm A
6 disarm disarm B
12.25. Addressing of wireless detectors to sections sequence: 61 nns
If the control panel is split (see 12.21.) and is equipped with a 65R module, the wireless detectors can be addressed to
sections by entering:
61 nns
where: nn = wireless detector zone number: from 01 to 16
s= section: 1 = A, 2 = B, 3 = C (common section - it is armed only when both A and B are armed). If the
control panel is not split, and s=2 (or s=3) is selected, this detector will be bypassed while partial
arming.
Example: to address wireless detector zone number 3 to section A enter: 61 031
Factory default setting: detectors 1 - 10 are addressed to A, detectors 11 - 16 are addressed to B
12.26. Addressing of the user codes to sections sequence: 62 nns
If the control panel is split (see 12.21.), the user codes can be addressed to sections A or B by entering:
62 nns
where: nn = user code number: from 01 to 14
s=section: 1 = A, 2 = B
Notes:
•If the control panel is not split, this setting has no effect.
•Master code (MC) can not be addressed. If the system is split, the use of MC will arm all sections if no section is armed or it will
disarm all sections if any is armed. If you want to operate only section A with master code, enter F1 MC and F2 MC for section B.
Example: to address user code number 4 to section A enter: 62 04 1
Factory default setting: all user codes (01 - 14) are addressed to section A
12.27. Addressing of wireless controllers to sections sequence: 63 nns
If the control panel is split (see 12.21.) and is equipped with a 65R module, the wireless controllers (RC-11, RC-22 and
JA-60D) can be addressed to A or B section by entering:
63 nns
where: nn = number of the enrolled controller from 01 to 08 (c1 to c8)
s= section: 1 = A, 2 = B
Notes:
•If the control panel is not split, this setting has no effect
•For the JA-60F keypad this setting has no effect (its user codes are determined by 62nns setting)
Example: to address controller number 5 to section A enter: 63 051
Factory default setting: all wireless controllers are addressed to section A
12.28. Automatic arming / disarming setting sequence: 64 nahhmm
The control panel can automatically arm and disarm for a requested period of a day. Up to ten instructions (time & action)
can be programmed in the period of one day by entering:
64 nahhmm
where: n= instruction number from 0 to 9
a= action (see the actions' table)
hh = hours (from 00 to 23)
mm = minutes (from 00 to 59)
Notes:
•If any automatic action is selected, it will be preformed everyday in the
programmed time, following the internal control panel clock (see 12.27.).
•The automatic arming and disarming can be overridden manually anytime (by an user code or a remote control)
•If the control panel is in the requested arming mode before the action time, performance of the programmed action will not change
the arming
Example: to program an automatic complete arming of the system at 21:15 everyday enter: 64 0 1 21 15
Factory default setting: all instructions are set for no action

Alarm system JA-65 MAESTRO - 17 - MFM51210
12.29. New service code setting sequence: 5 nSC nSC
The Service Code can be used to enter the programming mode. A new Service Code must be entered twice in the
sequence to avoid an error.
To change the code enter:
5 nSC nSC where nSC is your new Service Code (four digits)
Example: to change service code to 1276 enter: 5 1276 1276
Factory default setting: service code is 6060
12.30. User Mode entering Sequence: 6 9 9 9
This sequence is used to switch from the Service Mode to the User Mode, where you can set zones´ bypass (see User´s
manual). You can exit the User Mode by pressing the “N” button. The bypassed zones will remain active after the leaving
the User Mode.
12.31. Real time and date setting sequence: 4 hh mm dd MM YY
The control panel has a built in real time clock. All events are stored to the event memory including the time of the event.
The clock should be set after the installation is completed. Time Setting:
4 hh mm dd MM YY
where hh = hours (24 hr. cycle)
mm = minutes
dd = day
MM = month
RR = year
Example: on Jun. 30 2005 at 17:15 enter: 4 17 15 30 06 05
After the control panel is powered, its internal clock’s default setting is: 00 00 01 01 00
Note: detail control panel event history can be viewed with a connected PC using Comlink software.
13. System testing
For testing, the control panel should be in the programming mode - "P" indicated on the keypad (see part 12. how to
enter programming). No alarm can be triggered in the programming mode and any triggering of a detector (wireless or
wired) will make a beep (press F to select for a loud beep by siren) and the LED display will show for a while which zone
was triggered. An enrolled wireless controller or siren signal receiving will be similarly indicated.
•Some detectors (JA-60P, JA-60N, JA-60B etc.) have an extra testing mode, which is usually activated for 5
minutes after the detector’s cover is attached (see manuals of the particular detectors). If the detector is in testing
mode, it will indicate triggering locally, and it will also indicate the triggering on the control panel keypad. Note,
that the JA-60P motion detector in normal mode (after 5 minutes testing mode) is ready to send information about
next triggering 5 minutes after the previous triggering (this period can be shortened to 1 minute - see setting of
the JA-60P detector).
•Triggering of a detector wired to the H module is indicated at the control panel keypad for about 2 seconds
after the triggering. It means, that if a detector is permanently triggered for a longer period, it will not be indicated.
If a double balanced input loop (2x 4k7) is used, then the control panel distinguishes triggering of the detector
from its tampering.
•The best way of testing is via a connected PC using the Comlink software (see section 19). In the service
events window you will get a chronological record of all performed tests, including zones setting, quality of
communication etc.
The system can also be tested by a user in the user mode (confirmed by a “U”). The user mode is accessible with the
Master code. To open the user mode enter F 0 MC (= Master Code) when the control panel is disarmed.

Alarm system JA-65 MAESTRO - 18 - MFM51210
14. Voice & Pager messages setting
A control panel equipped with the X module can automatically send 2 voice and 5 short text messages (or dial a Pager) .
The most convenient programming of the dialer is via a connected PC using the Comlink software (see section 19).
Programming can also be performed manually from the keypad:
•Enter the programming mode (entering F 0 SC - SC = Service Code, factory default SC=6060), indicated by a „P“ on
the LED display. This can only be done while the panel is disarmed.
•The parameters of the dialer can be set by entering programming sequences from the keypad. Any unfinished
programming sequence can be terminated by pressing the Nkey.
•To exit the programming mode, press the N key („P“ will turn off). If any fault is indicated when you try to exit the
programming mode, the control panel will inform you about the problem (see 12.22.).
•Telephone numbers and the voice message(s) can also be set up in the User Mode when enabled (see section 12.6.)
List of the voice & Pager programmable parameters
Function sequence options factory d. note
Dialing method 90x 901 = tone 900 = pulse tone valid also for PCO
transfer
Triggering of the dialer with a Panic alarm 91x 911 = YES 910 = NO 1
Triggering of the dialer with an Intruder alarm 92x 921 = YES 920 = NO 1
Triggering of the dialer with a Fire alarm 93x 931 = YES 930 = NO 1
Triggering of the dialer with a Tamper alarm 94x 941 = YES 940 = NO 1
Triggering of the dialer with a Technical alarm 95x 951 = YES 950 = NO 1
Telephone line checking enabled 99x 991 = YES 990 = NO NO
Store telephone numbers for voice message 7xx..x F y xx...x = tel. number, y=
memory 1 to 4, pause = F0
Pager dialing programming 7x.xF9z..zF5 x..x = provider tel. number z..z
= pager number + message
1:
2:
3:
4:
5:
Erase telephone number 7F0Fy y= memory 1 to 5, entering
7F0F0 erases all
Record voice messages (1 & 2) mess. 1 enter 85 then push button on X module and speak (10sec.)
mess. 2 enter 86 then push button on X module and speak (10sec.)
Dialer testing 89 2 messages - 88 & 89
14.1. Telephone number entering sequence: 7xxx....xxFy
Store telephone numbers for voice message entering:
7 xx... xx F y
where xx...xx = telephone number
y= memory number from 1 to 4
A telephone number can have a maximum of 16 digits. A pause can be entered with F0 (pause can not be entered as the
first digit).
Example: to store tel. number 483 123456 to memory no. 2 enter: 7 483 F0 123456 F2
Note: enter a pause (F0) after the last digit of a number which is calling a mobile phone. This way the number will be
called only once and the dialer will not check the line signals (some mobile phone systems do not generate standard
telephone line signals).
When activated, the dialer will disengage all other devices hooked up to the phone line (telephone, fax..). It will then,
one by one, call and play the user recorded message, for all programmed numbers. If the dialer makes a successful
connection to a programmed number, it will not call that number again. If the number is busy, the dialer will make 3 more
attempts to call it.
Empty tel. number memories are skipped. If all memories are empty, the dialer is completely disabled. If the dialer is
communicating to the monitoring station, the data is sent to the monitoring station at first.
To delete a telephone number enter:
7 F0 Fy
where yis a memory number from 1 to 4
entering 7 F0 F0 will erase all tel. numbers, including the Pager number

Alarm system JA-65 MAESTRO - 19 - MFM51210
Store number to call Pager (to memory number 5) entering:
7 xx..x F9 zzz....zz F5
where xx...x = provider prefix
F9 = separator (it will wait for a provider’s signal and will switch to DTMF if not used)
zzz...zz = pager number and numeric message and other specific codes (language
selectors, end of message etc.) if requested by the Paging provider
F5 = to store the number to memory no. 5
As a maximum 32 digits can be stored to memory number 5. Special characters can be entered with the following Fx codes:
pause F0
∗ F7
# F8
Example: enter 7 0611 F9 1 1234 555 F80 F5 if the provider prefix is 0611, the Pager number 1234 and the message
555. Number 1 after F9 is a language selector, code F80 represents # 0 = end of message.
Note: some Paging providers also offer an option to send the message as an SMS to the GSM network. Consult your
Paging provider for details if you have trouble sending a message to the Pager.
To delete the Pager number enter:
7 F0 F5
If the memory number 5 is empty, no message will be sent to a Pager.
Factory default setting: all memories from 1 to 5 are empty.
14.2. Voice message(s) recording sequence: 8x
You can record two different voice messages (10 sec. each). Depending on the setting in section 14.3, a particular
message will be sent under different situations. Recording of the messages:
a) enter 85 on the keypad
b) press and hold push button on the X module
c) speak towards the module (max. 10 s)
d) release the button, message will be replayed
This results in the recording of message number 1. To record message 2 enter 86 in step a)
If you prefer sending only one, but longer, message (20 sec.), record message by entering 84 in step a). By programming
as described in section 14.3 you can specify which alarms will trigger the sending of a message.
Notes:
•Make the messages brief and clear. The dialer repeats the message to each called number for 40 seconds.
•The voice messages are stored in non-volatile memory and can be changed whenever you want to by repeating the above steps.
•The existing messages can be played by momentarily pressing the push button on the X module (or by entering F9 while in stand
by mode).
14.3. Telephone dialer triggering sequences: 9 y x
With sequences 91x to 95x you can select which alarms will trigger the telephone dialer to call and which ones will not.
Enter:
9 y x where
Example: if the dialer should not call when the system is tampered, enter 940
Factory default setting: all alarms will trigger the dialer (it means 911, 921, 931, 941 & 951)
If two different voice messages were recorded (see 14.2.), then parameter xspecifies which message will be sent.
y Alarm
1 Panic – silent
2 Intruder
3 Fire
4 Tampering
5 Technical trouble
x reaction
0 not to call
1 voice message & Pager code
2 voice message only
3 Pager code only
x reaction
0 not to call
1 send message #1 and Pager
code
2 send message #2 only
3 Send Pager code only

Alarm system JA-65 MAESTRO - 20 - MFM51210
14.4. Dialing method sequence: 9 0 x
Enter: 9 0 1 for tone dialing
9 0 0 for pulse dialing (this option is blocked for some countries)
Note: this dialing method setting is also valid for Monitoring station communications as well as remote PC access
Factory default: tone dialing
14.5. Telephone line checking sequence: 9 9 x
If this function is enabled, the dialer will check regularly if the telephone line is ready to make a phone call. If the line is not
ready for more than 15 minutes, the keypad will indicate a telephone line failure (failure L). Not working telephone line or
a phone conversation or Internet connection longer than 15 minutes can cause a fault.
options: 9 9 1 checking enabled
9 9 0 checking disabled
Note: this setting is also valid when the dialer is used for Monitoring station communications as well as remote PC access
Factory default setting: checking disabled
14.6. Telephone dialer testing sequence: 8 9
Entering 89 and the dialer will call the programmed numbers once. You will hear the telephone line signals from the
control panel built in speaker during the test (if the dialer is triggered by an alarm in normal operation, it will call silently).
Testing can be terminated with the N key.
If two different voice messages were recorded, then use sequence 88 to test the sending of the first message and 89 to
test the sending of the second message.