JABSCO 23920-2403 User manual

UTILITY PUPPY
MODELS:
23920-2403/2503 12/24 V UTILITY PUPPY 2000
23920-2213/2313 12/24 V UTILITY PUPPY 3000
FEATURES:
Continuous rated, heavy duty, dry running pumps for
bilge, deckwash and general purpose use.
lISO 8846 MARINE (Ignition protection).
lISO 8849 MARINE (Bilge pump standard).
lBilge debris present no problem to these
bronze bodied, flexible impeller pumps.
lSimple design means fewer wearing
parts.
Utility Puppy 3000
l2580 lph (570 gph) output.
lTen minutes dry running (after initial prime).
lSelf priming to 2.4m (8 ft).
lLong life mechanical seal.
Utility Puppy 2000
l1920 lph (390 gph) output.
lTwenty minutes dry running (after initial prime).
lSelf priming to 1.2m (4 ft).
UTILITY PUPPY PERFORMANCE
Approximate performance for new pump, pumping water at
20 °C, with fully charged battery.
Total Head Utility Puppy
2000
Utility Puppy
3000
mftl/m
UK
gpm l/m UK gpm
0 0 38 8.4 50 11.0
1 3 37 8.0 48 10.5
2 7 35 7.7 45 10.0
4 10 30 6.6 42 9.0
6 19 25 5.5 38 8.4
826 347.5
10 32 30
12 39 25
INSTALLATION INSTRUCTIONS:
Jabsco Utility Puppies can be mounted on any flat surface.
Fit the pump in a dry, well ventilated position where there
is full access for service. If installed in a vertical position
the motor must be above the pump head. Use the rubber
grommets provided to minimise vibration, do not
overtighten the mounting screws.
¾” BSP male threaded fittings should be used to connect
25mm (1” i.d.) suction and discharge hoses. Secure the
hose to the fittings with stainless steel hose clamps. Use
spiral reinforced hose (with a smooth internal bore) that
will not collapse under suction, or rigid or semi rigid
pipework systems. The pipework must be compatible with
the liquid being pumped. Pipe runs should be kept as
straight and short as possible, avoiding rising and dipping
over obstructions. Fit an inlet strainer on the inlet hose to
prevent blockage.
WIRING INSTRUCTIONS
Make all electrical connections in dry locations,
connections in humid environments should be sealed to
prevent corrosion. Protect the circuit with a correctly sized
fuse or circuit breaker in the positive (+) lead as close as
possible to the power source. Select the correct cable size
from the chart below. Inadequate voltage at the motor ter-
minals when the pump is running (not less than 10%
below rated voltage at full load) due to partially discharged
batteries or insufficient cable size may result in blowing
fuses, failure to start or poor pump performance.
Connect the black motor wire to the negative (-) battery
terminal. The red wire should run via a suitably rated
switch or circuit breaker to the positive (+) battery terminal.
WARNING: If the fuse fails repeatedly do not
fit a heavier fuse or bridge the fuse terminals
with silver paper or metal wire. Failure to
observe this instruction may result in a fire
hazard due to overheating of cables.
WARNING: All marine pumps discharging
overboard must be installed with the over-
board discharge well above both static and
heeled waterlines.

ELECTRICAL WIRING INFORMATION
Model No. Voltage Amp Draw Max. Fuse
Size Min. Wire Size
Max. length of wire
between (+) & (-)
battery terminals
23920-2213 12V 21 amp 25 amp 4mm² (50/0.3mm)
6mm² (84/0.3mm)
Up to 7m
Over 7m
23920-2313 24V 11 amp 15 amp 2.5mm² (30/0.25mm)
4mm² (50/0.3mm)
Up to 7m
Over 7m
23920-2403 12V 13 amp 15 amp 1.5mm² (32/0.25mm) 4.5m
23920-2503 24V 7.5 amp 10 amp 1.5mm² (32/0.25mm) 4.5m
UTILITY PUPPY PARTS LIST
Key Description Utility Puppy 3000 Utility Puppy 2000
Qty Part No. Qty Part No.
1 End Cover Screws 4 X3001-147F 4 X3001-147F
2 End Cover 1 23825-0000 1 23825-0000
3 End Cover Seal 1 X4020-257A 1 X4020-257A
4 Impeller - Nitrile 1 7273-0003 1 6303-0003
5 Cam 1 53023-0000 1 53023-0100
6 Cam Screw 1 X3002-147F 1 X3002-147F
6a Cam Screw Seal 1 X4020-105A 1 X4020-105A
7 Pump Body 1 53024-2000 1 53024-2000
8 Slinger 1 X4020-221B 1 6342
9 Motor 12v SP8012-0261 SP8012-0165
Motor 24v SP8012-0262 SP8012-0166
10 Seal 1 SP8021-0301B 1 SP2701-52
11 Pump/Motor Screws 2 X3001-147F 2 X3001-147F
EXPLODED VIEW & PARTS LIST
Weight: Utility Puppy 2000 3.3kg (7lb)
Utility Puppy 3000 4.6kg (10lb)
Warranty: All products of the company are sold and all services of the company are offered subject to the company’s warranty and terms and conditions of sale, copies of which will be furnished upon request.
©Copyright 2002 ITT Industries 43001-0511 rev 12/2002 qxd
Jabsco
ITT Industries
Jabsco, 20 Icon, Foothill Ranch, CA 92610
Tel : [phone] Fax : [phone]
Jabsco, Bingley Road, Hoddesdon, Hertfordshire, EN11 0BU
Tel : [phone] Fax : [phone]
Fluid Products Canada,55 Royal Road, Guelph, Ontario N1H 1T1
Tel : [phone] Fax : [phone]
NHK Jabsco Co Ltd,3-21-10, Shin - Yokohama, Kohoku-ku, Yokohama 222
Tel : [phone] Fax : [phone]
Jabsco GmbH,Oststraße 28, 22844 Norderstedt
Tel : [phone] Fax : [phone]
USA
UK
CANADA
JAPAN
GERMANY
www.jabsco.com