Jacuzzi 67416-3D04Y User manual

1
Questions, problems, missing parts? Before
returning to your retailer, call our customer service
department at 1-800-288-4002, 6 a.m. - 5 p.m.,PT
and 9 a.m. - 8 p.m.,ET, Monday - Friday.
TWO HANDLE ROMAN TUB FAUCET
Jacuzzi Item # MX 22826 / MX 22827 /MX 22817 / MX22845
MODEL # 67416-3D04Y / 67416-3D01Y / 67416-7001Y
ATTACH YOUR RECEIPT HERE
Serial Number___________________
Purchase Date___________________
2022/06/01 V2
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate, or install the product.
WARNING:
•Follow the installation instructions carefully. Proper installation is the installer’s responsibility.
•Failure to follow correct installation procedures can result in the faucet being loose, which can result in serious injury.
CAUTION:
•Check local building codes before beginning installation to ensure compliance.
PREPARATION
Before beginning the assembly of this product, make sure all parts are present. Compare parts with the package
contents and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 90 minutes (including removal of old faucet)
Tools Required for Assembly (not included): Adjustable Wrench, (2) Supply lines
/ 67416-2708Y
®
QD86000

2
ASSEMBLY INSTRUCTIONS
From underneath the deck, insert the middle body
with the rubber washer (1), metal washer (2) and
mounting nut (3) through hole. From above, thread
the connector (4) onto middle body. Tighten the
mounting nut (3), so that the connector (4) sits flush
to the surface of working area. Note: The middle body
must turn to the direction as shown in the diagram.
23
Drill holes in FINISHED DECK per diagram.
NOTE: This kit is intended for installation up to
1-1/4 in. thick.
1
Place the spout assembly (1) onto the connector (2).
Be sure the spout assembly (1) is resting firmly on
the deck. Push down on spout assembly (1) and
tighten set screw (3) with Allen wrench
(Hex: 3.2mm, 4). Insert the cap (5).
Unscrew the set screws (1) from the handle
assemblies (2)with Allen wrench(Hex:2.5mm,6) and
remove the handle assemblies (2) from the valve
bodies. Loosen the flanges (3) from the valve bodies.
Adjust the washers (4) and mounting nuts (5) to the
bottom of valve bodies.
45
From underneath the deck, insert the valve body with
the rubber washer (1), metal washer (2) and mounting
nut (3) through hole on the right (cold) side. From
above, thread the flange (4) onto valve body. Tighten
the mounting nut (3), so that the flange (4) sits flush
to the surface of working area. Then insert the other
valve body through holes on the left (hot) side and
install in the same way. Note: Hot side end valve is
labeled.
6
5 in. min.
8~16 in.
3 in. min.
1-1/4 in. MAX. DECK THICKNESS
1-1/8 in. dia.
1-3/8 in. dia.
Remove connector (1) from the middle body. Adjust
the washers (2) and mounting nut (3) to the bottom
of middle body.
2
1
4
3
5
2
1
4
3
5
12,7 cm min.
7,62 cm
min.
Diam. de 3,49 cm
~ de 20,32 à 40,64 cm
Diam. de 2,85 cm
1-3/8 in. dia.
Diam. de 3,49 cm
ÉPAISSEUR MAXIMALE DU COMPTOIR DE 3,17 CM
2
3
4
1
2
345
1
2
31
4
2
3
1
2
345
2
1
4
3
6
QD86000

3
ASSEMBLY INSTRUCTIONS
8
Place the handle assembly (1) onto the right (cold)
valve (2). Then thread the handle seat (3) onto the
flange (4). Place the set screw (5) into handle
assembly (1) and tighten set screw (5) with Allen
wrench (Hex: 2.5mm, 6), Place the other handle
assembly onto the left (hot) valve and install the
same way.
7
Turn on hot and cold water supplies and flush water
lines for one minute. After flushing,turn the handles
all the way off to shut off the water.
10
Connect a 1/2 in. IPS faucet connector (not included)
to the water supplies underneath the sink using
wrenches (not included).
NOTE: Refer to the local plumbing codes for
permissible types of water supply connectors.
9
2
1
3
2
5
1
4
6
1
2
3
4
Connect the flexible water supply hose (1) to the
bottom of valve bodies (2) as show. Align middle
body (3) in a position which will allow maximum
clearance to connect hoses. Carefully bend the
hoses to fit available space. Carefully thread the hose
couplings to the sides of the middle body (3). Tighten
nut (4) securely with wrench.
QD86000

4
ASSEMBLY INSTRUCTIONS
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
There is a leak from under the handle
or there is a leak from the spout when
the faucet is off.
There is a leak from the spout base
when the faucet is on.
1. The bonnet nut is not tight enough.
2. The cartridge is damaged.
The o-ring which is on the connector
under the spout is worn.
1. Remove the handle and retighten
the bonnet nut.
2. If the problem occurs after
retightening the bonnet nut, call
customer service for a new cartridge
and replace it after you receive the
new cartridge.
Call customer service for a new o-ring
and replace it after you receive the
new o-ring.
The manufacturer warrants this faucet to be free from defects in workmanship and material present at time of shipment
from the factory for a limited lifetime from the date of purchase. This warranty applies only to the original purchaser. The
manufacturer agrees to correct such defects at no charge or, at our option, replace the faucet with a comparable or
superior model. To obtain warranty service, call our customer service department at 1-800-288-4002 for return
authorization and shipping instructions. You may be required to present a copy of your sales receipt as proof of purchase.
All cost of removal and reinstallation are the expressed responsibility of the purchaser. Any damage to the faucet by ac-
, are the purchaser’s
responsibility. The manufacturer assumes no responsibility whatsoever for faucet installation during the warranty period.
There is no further expressed warranty. The manufacturer disclaims any and all implied warranties. The manufacturer shall
not be liable for incidental, consequential or special damages arising at or in connection with product use or performance
rights which vary from state to state. This warranty supersedes all prior warranties.
WARRANTY
CARE AND MAINTENANCE
•
and void your warranty.
QD86000

5
For replacement parts, call our customer service department at
1-800-288-4002, 6 a.m. - 5 p.m., PT and 9 a.m. - 8 p.m.,ET, Monday - Friday
REPLACEMENT PARTS LIST
PART DESCRIPTION PART#
1
3
Printed in China
2
01
02
03
Handle assembly RQ84817/RQ84826/RQ84827/RQ84845
Cartridge H RQ86000
Cartridge C RQ87000
QD86000