JADO Classic Victorian 850.003 Series User manual

Installation Instructions
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
©JADO USA 2003
Products Luxury Faucets and Accessories
Single Lever Lavatory
and Bidet Faucets
4TEST INSTALLED FITTING AND
CONNECTIONS FOR LEAKS
With FAUCET HANDLES in OFF position, turn on
WATER SUPPL ES (1) and check all connections
for leaks.
Remove AERATOR from FAUCET. Operate both
HANDLES to flush water lines thoroughly.
1
1
Operate L FT ROD (2) and fill lavatory or bidet with
water. Check that DRA N STOPPER (3) makes a
good seal and retains water in lavatory or bidet.
Adjust stopper height by repositioning Lift Rod (2)
and tightening SET SCREW (4).
Release DRA N STOPPER (3) and check all drain
connections and "P" trap for leaks. Tighten if
necessary.
nstall AERATOR into FAUCET.
2
4
3
5HELPFUL HINTS FOR CLEANING AND MAINTENANCE
The solid brass product you have just purchased has been designed to give you years of beauty and service. It is
important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.
First and foremost, it is important (as it is with any fine piece of jewelry or furniture) that the product be wiped clean and
dry with a soft damp cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/polish be used on JADO products.
The abrasive nature of such products will eventually destroy the finish and void the warranty.
n the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,
but we do not recommend it be used on an everyday basis.
109127 109127
JADO USA
7845 East Paradise Lane
Scottsdale, AZ 8526O
Phone:(8OO) 227-2734
Fax: (8OO) 552-JADO(5236)
www.jadousa.com
Classic
Victorian
Product Numbers
Lavatory
85O/OO3/...
Product Numbers
Bidet
85O/OO4/...
TO THE PURCHASER OF JADO BRASS PRODUCTS
Attention inst ller:
Please leave This Pamphlet for The Owner
The state of California has mandated under Proposition #65 that
manufactures of products, including faucets which come into
contact with potable water, must warn the consumer if the product
contains materials listed by the state as a carcinogen or
reproductive toxin. Lead, which is contained in all brass faucets in
limited amounts appears on the State's list.
Preliminary industry tests have indicated that users of faucets
made from brass face no significant danger, however,
California Proposition #65 requires that we provide you with the
following notice:
NOTICE: JADO products conform to industry
requirements of water conservation under the
ASTM / ANSI A112.18.1M-1994 plumbing code.
Lavatory, bidet, wet bar and kitchen faucet sets
have a maximum flow rate of 2.2GPM. Shower
heads, hand showers and body sprays have a
maximum flow rate of 2.5GPM.
Warning: This product contains an element
known to the State of California to cause cancer
of reproductive harm.
JADO BATHROOM AND HARDWARE MFG. CORP.
7845 East Paradise Lane
Scottsdale, AZ 85260
t is important to note that it is normal to expect signs of usage over time.
Th nk you for selecting JADO for your home.
POLISHED BRASS AND CUSTOM FINISHWARRANTY: A 1YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the
first residential owner against defects in materials and workmanship. Due to the ever-changing finish of Patina products, the finish warranty
is excluded. Warranty shall not include problems related to the installation of the product.
MECHANICS
MECHANICAL WARRANTY: A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure
related to defects in materials and workmanship but not installation.
CONDITIONSTO WARRANTIES
JADO Bathroom & Hardware Manufacturing Corp.places the following conditions on its finish and mechanical warranties to the first residential owner only.
JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.
JADO warranties exclude General Finishes, Polished Brass and Custom Finishes exposed to marine environment and direct exposure to sunlight.
JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration
due to normal use.
JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.
In the event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased
along with proof of purchase.
JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be
defective after appropriate examination.
JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser
owns their home.
JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited
warranty claims.This limited warranty is non transferable.It does not apply in the event of product damage due to the use of other than
genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by
a plumber, contractor, service provider or member of the purchaser’s household).The limited warranty excludes damage due to aggressive
air or water conditions, or harsh or abrasive cleaners and/or materials.This limited warranty excludes all industrial, commercial and business
usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic
components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration.This limited warranty
does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential
damages, all of which are expressly disclaimed.This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996
and installed in the United States and/or Canada.
This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to
state or from province to province.This limited warranty does not cover any liability for consequential or incidental damages, all of which
are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose. Insome states or provinces the exclusion or limitation of incidental or consequential
damages is not allowed, so those exclusions may not apply to you.
JADO Bathroom & Hardware Manufacturing Corp.provides the following warranties only to the first residential owner of our products.
FINISHES
JADO FAUCET LIFETIME FUNCTION AND FINISH LIMITED WARRANTY

1INSTALL FAUCET (LAVATORY AND BIDET)
Turn off hot nd cold w ter
supplies before beginning.
CAUTION
ROUGHING-IN
DIMENSIONS
Feed FAUCET SUPPLY TUBES (3) and SHANK (4) through ESCUTCHEON (1) and mounting hole of lavatory, bidet
or mounting surface.
SI GLE HOLE MOU TI G
nspect ESCUTCHEON (1) for O-R NG (2) fitted into O-ring groove . Place ESCUTCHEON (1) with O-R NG (2) over mounting hole.
FAUCET I STALLATIO WITH OPTIO AL DECK ESCUTCHEO (8).
Thread two (2) 2-1/4" long ESCUTCHEON STUDS (12) into base of DECK ESCUTCHEON (8).
nstall the two (2) 0-R NGS (9) into the recesses under the DECK ESCUTCHEON (8). Place the DECK ESCUTCHEON (8)
onto the mounting surface. From below install two (2) FLAT BRASS WASHERS (10) onto the ESCUTCHEON STUDS (12)
and secure with W NG NUTS (11) supplied with kit. Before final tightening, DECK ESCUTCHEON (8) should be centered
on mounting surface. Tighten W NG NUTS (11).
With DECK ESCUTCHEON (8) installed, complete the installation following the instructions above
(SI GLE HOLE MOU TI G).
From below, nstall RUBBER WASHER (5), RETA N NG WASHER (6) and LOCKNUT (7) onto faucet SHANK (4).
Before final tightening, faucet should be seated flush on ESCUTCHEON (1). Adjust faucet so that it is centered and covers
mounting hole. Tighten LOCKNUT (7) using a 13mm or adjustable wrench. Do not over tighten. nstall POP-UP ROD (13).
B DET
MOUNT NG
SURFACE
3
2
5
1
WATER SUPPLY CONNECTIONS
Supply connections are made after bidet has bee installed.
Important: Use only SUPPLY ADAPTERS (1) furnished with
lavatory or bidet faucet. Assemble SUPPLY ADAPTERS (1)
(furnished) to FAUCET SUPPLY TUBES (2) as shown in
Figure 2 . Push SUPPLY ADAPTER (1) onto SUPPLY TUBE (2)
and tighten SUPPLY NUT.
Connect water supplies to SUPPLY ADAPTERS (1)
with 1/2" PS FLEX BLE SUPPL ES (3) or 3/8" O.D.
BULL-NOSE R SERS (4). Connect HOT supply to
left side and Cold to right side.
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink
copper supply when bending. Use tubing cutter
to cut to proper length.
3
4
FERRULE
COLD
HOT
BRASS SPLIT RING
BRASS FRICTION WASHER
RUBBER SEAL
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS MUST BE
PURCHASED SEPARATELY.
SUPPLY NUT
FAUCET SUPPLY TUBE
Lavatory
Figure 2
13 13
LAVATORY
MOUNT NG
SURFACE 11
5
10
1
4
3
2
9
12
9
8
12
6
7
6-1/2"
NOTE: MOUNT NG HOLE
S 1-3/8" D.
2-5/8" D. 2-5/8" D.
14-5/8"
MAX 1-5/8" MAX 1-5/8"
4-7/8"
3-1/8"
28
2-1/8"
1-1/4" O.D. 1-1/4" O.D.
MAX 2"
7"
5-3/4"
4-7/8"
80
3-1/4"
14-5/8"
2-1/8"
MAX 2"
7"
GROOVE
Bidet
H
O
T
C
O
O-R NG GROOVE
H
O
T
C
O
H
O
T
C
O
H
O
T
C
O
109127 109127
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter Regular Screwdriver
Basin Wrench
Lavatory Bidet
APPLY SEALANT
OR TEFLON TAPE
2
A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TA LP ECE (10) and
thread into DRA N BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRA N (3). From below assemble
RUBBER GASKET (4), PLAST C WASHER (5) and LOCK NUT (6) onto
DRA N FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 2
FIG. 2b
FIG. 2c FIG. 2c
FIG. 2
FIG. 2b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SW VEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SW VEL (15) to P VOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SW VEL (15) and
tighten SET SCREW (17)
Assemble P VOT ROD (11), and P VOT NUT (12) as shown. nstall CONCAVE
WASHER (19) into P VOT ROD OPEN NG (9) if not preinstalled. Hand tighten
P VOT NUT (12). Drop STOPPER (13) into drain.
( To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13) . Make connection to "P" TRAP.
nspect inside DRA N BODY (7) that SEAL (8) is installed. Thread
DRA N BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
1517
18
2
10
14
13
11
The P VOT ROD OPEN NG (9) in DRA N BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.