JADO Perlrand 892/312 Series User manual

Installation Instructions
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
©JADO USA 2003
Products Luxury Faucets and Accessories
Three Hole Bidet Set
Three Hole Bidet Set
with Vacuum Breaker
with Vacuum Breaker
8TEST INSTALLED FITTING AND
CONNECTIONS FOR LEAKS
With FAUCET HANDLES in OFF position, turn on
WATER SUPPLIES (1) and check all connections
for leaks.
Operate both handles to flush water lines thoroughly.
Turn diverter to rim wash and bidet spray.
Operate LIFT ROD (2) and fill bidet with water. DRAIN
STOPPER (3) should make a good seal and retain water
in bidet. Adjust stopper height if required by repositioning
LIFT ROD (2) and tightening SET SCREW (4).
Release DRAIN STOPPER (3) and check all drain
connections and "P" trap for leaks. Tighten if
necessary.
9HELPFUL HINTS FOR CLEANING AND MAINTENANCE
The solid brass product you have just purchased has been designed to give you years of beauty and service. It is
important to bring to your attention proper care and maintenance procedures, which will ensure its lasting beauty.
First and foremost, it is important (as it is with any fine piece of jewelry or furniture) that the product be wiped clean and
dry with a soft damp cloth after every use.
Second, under no circumstances should an abrasive cleaner or combination cleaner/polish be used on JADO products.
The abrasive nature of such products will eventually destroy the finish and void the warranty.
In the event of stubborn blemishes shown on the finish, we recommend use of Windex window cleaner with a soft cloth,
but we do not recommend it be used on an everyday basis.
It is important to note that it is normal to expect signs of usage over time.
Thank you for selecting JADO for your home.
109435
109435
JADO
JADO
1
1
2
3
4
JADO USA
7845 East Paradise Lane
Scottsdale, AZ 8526O
Phone: 8OO) 227-2734
Fax: 8OO) 552-JADO 5236)
www.jadousa.com
Product umbers
Bidet
892/312/...
892/313/...
892/314/...
Perlrand
TO THE PURCHASER OF JADO BRASS PRODUCTS
Attention installer:
Please leave This Pamphlet for The Owner
POLISHED BRASS A D CUSTOM FI ISH WARRA TY: A 1 YEAR LIMITED FINISH WARRANTY from date of purchase is provided to the
first residential owner against defects in materials and workmanship. Due to the ever-changing finish of Patina products, the finish warranty
is excluded. Warranty shall not include problems related to the installation of the product.
MECHA ICS
MECHA ICAL WARRA TY: A LIFETIME LIMITED WARRANTY is provided to the first residential owner on parts to be free from failure
related to defects in materials and workmanship but not installation.
CO DITIO S TO WARRA TIES
JADO Bathroom & Hardware Manufacturing Corp. places the following conditions on its finish and mechanical warranties to the first residential owner only.
JADO finish and mechanical warranties are limited to products correctly installed and used in a residential environment.
JADO warranties will not assume liability for damage due to abuse, mishandling, incorrect installation, improper maintenance, or deterioration
due to normal use.
JADO will not be liable for labor or other costs relating to the sale, installation, or replacement of their products.
In the event of a defect in any JADO product covered by this warranty, the product must be returned to the dealer where originally purchased
along with proof of purchase.
JADO's obligation under the warranty shall be limited to the repair or exchange of any product which has been determined by JADO to be
defective after appropriate examination.
The state of California has mandated under Proposition #65 that
manufactures of products, including faucets which come into
contact with potable water, must warn the consumer if the product
contains materials listed by the state as a carcinogen or
reproductive toxin. Lead, which is contained in all brass faucets in
limited amounts appears on the State's list.
Preliminary industry tests have indicated that users of faucets
made from brass face no significant danger, however,
California Proposition #65 requires that we provide you with the
following notice:
OTICE: JADO products conform to industry
requirements of water conservation under the
ASTM / A SI A112.18.1M-1994 plumbing code.
Lavatory, bidet, wet bar and kitchen faucet sets
have a maximum flow rate of 2.2GPM. Shower
heads, hand showers and body sprays have a
maximum flow rate of 2.5GPM.
Warning: This product contains an element
known to the State of California to cause cancer
of reproductive harm.
JADO BATHROOM AND HARDWARE MFG. CORP.
7845 East Paradise Lane
Scottsdale, AZ 85260
JADO warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser
owns their home.
JADO will provide, free of charge, at it’s sole option, replacement part(s) or product (or if no longer available, a comparable
product) to replace those which have proven defective in materials or workmanship.
Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to JADO for all limited
warranty claims. This limited warranty is non transferable. It does not apply in the event of product damage due to the use of other than
genuine JADO replacement parts, installation error, abuse, misuse, or improper care and maintenance (whether performed by
a plumber, contractor, service provider or member of the purchaser’s household). The limited warranty excludes damage due to aggressive
air or water conditions, or harsh or abrasive cleaners and/or materials. This limited warranty excludes all industrial, commercial and business
usage, whose purchasers are hereby extended a two year limited warranty (with the exception of solenoid valves and other electronic
components which carry a one year limited warranty) applying to all other terms of this limited warranty except duration. This limited warranty
does not cover labor charges incurred and/or damages sustained in installation, repair or replacement, nor incidental or consequential
damages, all of which are expressly disclaimed. This limited warranty is applicable only to JADO faucets manufactured after June 1, 1996
and installed in the United States and/or Canada.
This limited warranty gives the original consumer purchaser of an JADO faucet specific legal rights which may vary from state to
state or from province to province. This limited warranty does not cover any liability for consequential or incidental damages, all of which
are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including
those of merchantability or fitness for an intended purpose. In some states or provinces the exclusion or limitation of incidental or consequential
damages is not allowed, so those exclusions may not apply to you.
JADO Bathroom & Hardware Manufacturing Corp. provides the following warranties only to the first residential owner of our products.
FI ISHES
FAUCET LIFETIME FU CTIO A D FI ISH LIMITED WARRA TY
NOTE: Diverter valve is not a positive shut-off to rim wash.

JADO
JADO
Three Hole Bidet Set
with Vacuum Breaker
1Turn off hot and cold water
supplies before beginning.
CAUTION
ROUGHING-IN
DIMENSIONS
SMALL
END
LARGE
END
LARGE
END
VALVE
OUTLET
VALVE
OUTLET
PUTTY
1
2
3
2
FRONT
4
1
5
12
11
10
13
16
14
6
7
15 8
9
2
3
4
1109435 109435
INSTALL TRANSFER VALVE
2
3
Apply sealant or Teflon tape to threads of SPRAY ELL (1) and install
into TRANSFER VALVE (2). Note: Arrow on SPRAY ELL (1) points
down, see illustration.
Install "Y" HOSE ADAPTER (3) with SEAL (4) to bottom nipple of
TRANSFER VALVE (2) and tighten to make a water tight seal.
Install LOWER CONE SEAL (5) onto TRANSFER VALVE (2) and
insert TRANSFER VALVE (2) from under side of Bidet into the
proper diverter hole.
Install UPPER CONE SEAL (6), FRICTION WASHER (7) and
MOUNTING NUT (8) onto TRANSFER VALVE (2).
Tighten MOUNTING NUT (8) to secure the TRANSFER VALVE (2)
and make a water tight seal.
Thread TRANSFER VALVE ESCUTCHEON (9) onto MOUNTING
NUT (8) until snug against bidet ledge.
COLD
HOT
BIDET
LEDGE
6" TO 12"
1-3/4"
MAX 4"
1-1/8" D.
MAX 7"
MAX 2"
11" 2-1/8" D.
1-1/4" O.D.
SPRAY
1-1/8' D.
2-3/4" D.
2-7/16" D.
MAX 13"
DIVERTER
AND VACUUM
BREAKER
LIFT ROD
CONNECTIONS ARE FOR1/2" IPS
FLEXIBLE SUPPLIES or 3/8" O.D.
BULL-NOSE RISERS
Plumbers' Putty or Caulking
Adjustable Wrench
Phillips Screwdriver
Channel Locks
TOOLS REQUIRED
Tubing Cutter Regular Screwdriver
Basin Wrench
APPLY SEALANT
OR TEFLON TAPE
5INSTALL SUPPLY HOSES
INSTALL SPRAY BODY
Connect small end of SUPPLY HOSES (1) TO "Y" ADAPTER (2)
and larger end to each VALVE OUTLET.
Important: Loop SUPPLY HOSES (1) as illustrated
so they do not kink.
Connect one end of SPRAY HOSE (7) to HOSE ADAPTER (8)
and the other end to shank of SPRAY BODY (3). Tighten hose
connections to make a water tight seal.
For Lever Handles: Install
FRICTION WASHER (1) onto
base of LEVER HANDLE (2).
Turn VALVE to off position and
align LEVER HANDLE (2) as
shown or desired. Install LEVER
HANDLE (2) onto VALVE STEM (3)
and tighten SET SCREW (4)
with HEX WRENCH supplied.
JADO
JADO
1
Apply putty to the underside of SPRAY BODY
FLANGE (3) and install SPRAY BODY (3) into
spray hole of Bidet.
From underside of Bidet install RUBBER WASHER (4),
FIBER WASHER (5) and LOCKNUT (6) onto shank of SPRAY
BODY (3). Tighten LOCKNUT (6) to make water tight seal.
4
8
5
67
7
Connect water supplies to FAUCET (1) with
1/2" IPS FLEXIBLE SUPPLIES (2) or 3/8"
O.D. BULL-NOSE RISERS (3). Use adjustable
wrench to tighten connections. Do not over
tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to
proper length.
Supply connections are made after bidet
has been installed.
3
2
HOT
HOT
COLD
FRONT
COLD
FERRULE
COUPLING
NUT
1
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED
AND HAVE TO BE PURCHASED SEPARATELY.
Remove LIFT ROD NUT (1), METAL WASHER (2) and
RUBBER SEAL WASHER (3) from LIFT ROD GUIDE (4).
Drop LIFT ROD GUIDE (4) into pop-up hole of bidet.
From below install RUBBER SEAL WASHER (3), METAL
WASHER (2) and secure guide assembly with LIFT ROD NUT (1).
LIFT ROD GUIDE INSTALLATION
WATER SUPPLY CONNECTIONS
10˚10˚
APPLY SEALANT
OR TEFLON TAPE
4A FOAM SEAL (1) is installed on underside of FLANGE (2). (Plumbers
Putty may be used in place of FOAM SEAL (1) if desired.)
Apply sealant or Teflon tape to threads of TAILPIECE (10) and
thread into DRAIN BODY (7) making a water tight seal.
Drop FLANGE (2) into LAVATORY DRAIN (3). From below assemble
RUBBER GASKET (4), PLASTIC WASHER (5) and LOCK NUT (6) onto
DRAIN FLANGE (2). Do not tighten fully.
INSTALL POP-UP DRAIN
FIG. 4a
FIG. 4b
FIG. 4c
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
Adjust STOPPER (13) height by repositioning POP-UP ROD (16) in SWIVEL (15)
and tightening SET SCREW (18).
Assemble POP-UP SWIVEL (15) to PIVOT ROD (11) but do not tighten.
Drop POP-UP ROD (16) through other hole in POP-UP SWIVEL (15) and
tighten SET SCREW (17)
Assemble PIVOT ROD (11), and PIVOT NUT (12) as shown. Install CONCAVE
WASHER (19) into PIVOT ROD OPENING (9) if not preinstalled. Hand tighten
PIVOT NUT (12). Drop STOPPER (13) into drain.
(To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13). Make connection to "P" TRAP.
Inspect inside DRAIN BODY (7) that SEAL (8) is installed. Thread
DRAIN BODY (7) tight against FLANGE (2) to make a water tight seal.
10
9
7
6
12
19
16
1517
18
2
10
14
13
11
The PIVOT ROD OPENING (9) in DRAIN BODY (7) should face the rear
of the lavatory. Tighten LOCK NUT (6) on FLANGE (2) to make a water
tight connection with channel locks. Do not over tighten.
INSTALL VALVE BODIES
INSTALL VALVES
Thread LOCKNUT (10) to bottom of VALVE BODY (1). Make sure
FIBER WASHER (11) and RUBBER WASHER (12) are installed.
Insert VALVE BODY (1) through mounting hole from underside of BIDET.
Note: If HANDLES ASSEMBLIES are installed on VALVE BODIES (1) they
must be removed to install VALVE BODIES (13) from under bidet mounting
surface.
Thread ESCUTCHEON (14) with SEAL (15) onto VALVE BODY (13).Thread
HANDLE BASE (16) onto VALVE BODY (13) until snug against internal stop.
Thread ESCUTCHEON (14) counter-clockwise until seated against HANDLE
BASE (16). Set VALVE BODIES (1) so that their outlets are facing toward
TRANSFER VALVE (2) rotated about 10 degrees off center and then tighten
LOCKNUT (10) using wrench.
7
3
6
5
2
2
4
4
1
1
Hex wench
supplied
Note: VALVE BODY marked Hot is installed in the left Mtg. hole,
VALVE BODY marked Cold in the right when facing front of fitting.
Maximum mounting surface thickness is 1-1/4".
For Crystal handles: With VALVE
in off position align CRYSTAL
HANDLE (5) and install onto
VALVE STEM (3). Install
HANDLE SCREW (6) and tighten.
Install INDEX CAP (7).
6INSTALL HANDLES
8
9
10
11
12
For Diverter handle: Install DIVERTER
HANDLE (8) onto VALVE STEM (9) of
DIVERTER (10). Secure DIVERTER
HANDLE (8) with SCREW (11). Thread
HANDLE CAP (12) onto DIVERTER
HANDLE (8).
BIDET
MOUNTING
SURFACE
3
LEVER HANDLES.
CRYSTAL
KNOB
HANDLES