J&M Corporation CFBR-GL1800 User manual

© 2012 J&M Corporation. All rights reserved. 3/12
Bluetooth® Cell/Smart-Phone/
GPS/Radar Kit for GL1800
Driver Position
#
CFBR-GL1800
Installation
and Operation
Instructions

Installation Instructions
Diagram A
(a) (b)
(c)
Installing the Integration Terminal
►Diagram A
1. Remove:
left fairing pocket (a)
ignition switch cover (b)
wiring cover plate under left handlebar (c)
2. Clean the surface inside the left fairing pocket mounting area
with denatured alcohol.
3. Remove the backing from the double-sided mounting tape and
mount the CFBR-GL1800 on to the inner surface of the outer fair-
ing shell directly beside the fairing pocket location, making sure
that the fairing pocket can be reinstalled properly. Diagram A.
Note: The CFBR-GL1800 should be mounted as far rearward as
possible with the connection cables exiting forward toward the
front of the fairing.
Mounting the Multifunction/volume switch
assembly.
►Diagram A
1. Mount the multifunction/volume switch assembly by install-
ing the bracket/clamp assembly around the exposed handlebar,
between the left-side handlebar grip and switch housing.
2. Route the wire alongside the stock wiring down the handlebar,
under the ignition switch cover and into the left fairing pocket area
of the fairing.
3. Make connections as shown in Diagram B. Note: Disconnect
the factory Driver’s headset lead and plug the corresponding con-
nectors from the CBFR-GL1800 in-line between the factory (RED)
6-pin plugs.
Operation Instructions
Pairing the CFBR-GL1800 to Bluetooth Enabled
Devices.
1. To Pair To a Cell/Smart Phone.
a. Turn on the CFBR-GL1800 by switching the ignition switch to the
ACC or ON position. The LED on the multifunction switch assem-
bly will flash slow blue.
b. Press and hold down on the multifunction button for approxi-
mately 10 seconds. When the LED goes off, release the button.
c. Press and hold down on the multifunction button again continu-
ously for about 35 seconds, cycling thru the slow flashing blue,
to rapid flashing blue, to flashing red & back to rapid blue flash-
ing, at which point the CBFR-GL1800 is in pairing mode.
d. In the phone menu select Bluetooth and “search for devices”.
e. Once the JM_CORP_CFBR01 shows up on the phone’s display
select it and when asked for a PIN code type in “0000”.
f. The cell phone should now pair to the CFBR-GL1800 and the
blue LED should flash slowly.
2. To pair to a Bluetooth Enabled GPS.
a. Turn on the CFBR-GL1800 by switching the ignition switch to
the ACC or ON position. The LED on the multifunction button
assembly will flash slow blue.
b. Press and hold down on the multifunction button for approxi-
mately 10 seconds. When the LED goes off, release the button.
c. Press and hold down on the multifunction button again continu-
ously for about 35 seconds, cycling thru the slow flashing blue,
to rapid flashing blue, to flashing red & back to rapid blue flash-
ing, at which point the CBFR-GL1800 is in pairing mode.
d. Turn on the Bluetooth enabled GPS and select Bluetooth head-
set in the menu. Then select “search for devices”.
e. Once the JM_CORP_CFBR01 shows up on the GPS display select
it and when asked for a PIN code type in “0000”
f. The GPS should now pair to the CFBR-GL1800 and the blue LED
should flash slowly.
Note: The CFBR-GL1800 does not require re-pairing each time the
motorcycle is turned off. After initial pairing, the Cell Phone or GPS
unit should automatically reconnect with the CFBR-GL1800 each
time the ignition switch is turned on.
Operation of the CFBR-GL1800 with a cell phone.
1. After successfully pairing your cell phone with the J&M CFBR-
GL1800, make a phone call. During the phone call adjust the vol-
ume control on the cell phone to maximum. Make further volume
adjustments using the handlebar mounted volume control.
2. When receiving an incoming call the “incoming call indicator-
sound” will override all other audio in the drivers headset and will
be heard in the helmet speakers. If the phone is set to Auto Answer
the incoming call will automatically be connected. If the phone is
not set to Auto Answer the call can be answered by briefly depress-
ing the multifunction button one time. To reject the call depress the
multifunction button twice or simply ignore the ring tone.
3. To end the call depress the Multifunction Button briefly or wait
for the caller to hang up and the drivers headset will automatically
return to the GL-1800 audio system.
4. To redial the last number called, press the Multifunction Button
5. To “Voice Command” dial the cell phone, briefly press the
Multifunction Button once. The cell phone must support this fea-
ture in order to use “Voice Command” dialing.

Handlebar
multifunction
switch assembly
8-pin
plugs
Motorcycle’s
ACC power
plug
Red
3-pin plug
Driver's
helmet headset
(not included)
CMXB-GL18
Radar connection
harness
Black
3-pin plug
Radar Detector
J&M Plug-and-Play Radar
Detector Connection Harness
(Not Included)
CFBR-GL1800
Red 6-pin
plugs
Factory driver’s headset
extension lead
Red 6-pin
plugs Factory driver’s
headset harness
under fairing pocket
Diagram B
Operation of the CFBR-GL1800 with a Stereo
Bluetooth music capable cell phone.
1. After successfully pairing your cell phone with the J&M CFBR-
GL1800, activate the Bluetooth music function of your cell phone.
2. Using the volume control on the phone adjust the music volume
to maximum. Make further volume adjustments using the handle-
bar mounted volume control.
Operation of the CFBR-GL1800 with a Bluetooth
Enabled GPS.
1. Both music and Cell Phone can be streamed to the CFBR-
GL1800 from a Bluetooth Enabled GPS.
2.The Cell Phone is paired to the GPS and the Cell Phone functions
will be controlled by the GPS or the phone itself. (to answer, reject
or dial a call). Note: The Multifunction Button will not control the
Cell Phone in this configuration.
3.To end a call the GPS can be used or simply wait for the caller to
hang up.
4. The music from the GPS, if initiated, will resume when the call
has ended.
5. The GPS music volume should be adjusted as described above
in “Operation of the CFBR-GL1800 with a Stereo Bluetooth capable
Cell Phone” using the volume controls on the GPS.
Note: For simultaneous use of a Cell/Smart Phone and GPS with
the CFBR-GL1800 you must pair the GPS to the CFBR-GL1800 and
the Cell/Smart Phone to the GPS.

Thank you for the confidence you have shown in J & M by purchasing one
of our innovative products. It will give you many hours of riding pleasure. If
you have any questions during installation or require more information about
this product, you may call our Customer service Department (English only,
please) at 1-800-358-0881, Monday through Friday, 8:00 a.m. to 5:00 p.m.
Mountain Standard Time, U.S.A.
J&M Corporation
Tucson, Arizona, U.S.A.
Tel. [phone]
www.jmcorp.com
[email protected]
WARRANTY REGISTRATION FORM Please fill out this card completely and mail it immediately after purchase. Please be sure that your zip code
and serial number (if applicable) are legible. This will help us to serve you better.
(PLEASE PRINT)
Name ______________________________________________________________________________________________________________________________________________________
Address_____________________________________________________________________________________________________________________________________________________
City _______________________________ _________________________________State __________________________ Zip ______________________________________________________
Motorcycle mOther m E-mail ______________________________________________________________________________________________________
Make ___________________________________________ Model ______________________________________ Year __________________
Product part number ______________________________________________________________________
Serial number (if applicable)________________________________________________________________
Date of purchase _________________________________________________
Name of dealer it was purchased from ____________________________________________________________________________________
Mail to:
J&M Corporation
1415 S. Cherry Avenue
Tucson, AZ 85713
U.S.A.
Operation of Radar Detector function.
1. A radar detector can also be added using one of J&M’s Plug-
and-Play Radar Connection Harnesses. The beeps/braps from the
radar detector will be heard momentarily in the right-side speaker
of the drivers helmet headset regardless of what other functions
are being heard.
Noise and Interference
Motorcycle audio systems by their very nature are noisy. While we
do not guarantee this system to be completely free from electrical
noises and interference, we have taken many steps to achieve that
goal: the power supply system is well filtered, the unit is shielded
in its metal container, and the cables associated with the unit are
shielded.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to
operate the equipment.
FCC Regulations
This device complies with 15 of the FCC Rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interfer-
ence received, including interference that may cause undesired
operation.
Industry Canada Notice to Users
Operation is subject to the following two conditions: (1) This device
may not cause interference and (2) This device must accept any
interference, including interference that may cause undesired oper-
ation of the device Ref IC RSS 210 Sec. 5.11. The term”IC:” before
the certification/registration number only signifies that registration
was performed based on a Declaration of Conformity indicating
that Industry Canada technical specifications were met. It does not
imply that Industry Canada approved the equipment.

WARRANTY AND REPAIR INFORMATION
TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled out and
returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of this warranty,
and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned,
on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION.
WHO PROVIDES THE WARRANTY? This warranty is provided by J&M CORPORATION.
WHO IS PROTECTED? This warranty is extended only to the original owner of this J&M CORPORATION product and may not be trans-
ferred or assigned.
WHAT IS COVERED AND HOW LONG? This warranty covers all defects in material or workmanship of our product for a period of
2 years from date of original retail purchase. At its option, J&M CORPORATION will repair or replace any defective part(s) or
equipment.
The provisions of the warranty shall not apply to any unit which has been subjected to misuse, neglect, incorrect mechanical or
electrical installation, unauthorized modifications, accident, nor to units which have been repaired or altered outside of our factory.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY In the event that the product does not conform to this warranty, the product
should be shipped prepaid to the J&M CORPORATION service facility. Transportation charges, insurance fees, and labor costs for shipment,
removal, or reinstallation of our product are not covered by this warranty. Loss or damage in shipment is the sole responsibility of the freight
carrier.
FOR YOUR INFORMATION Repair as provided under this warranty is the exclusive remedy of the consumer. J&M CORPORATION shall
not be liable for any incidental or consequential damages or for breach of any express or implied warranty on this product. Except to the
extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is limited
in duration to the duration of the warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights which vary from state to state.
J&M CORPORATION reserves the right to make changes in design and to make improvements in its products without the obligation to
incorporate the changes or improvements in any of its previously manufactured products.
J&M CORPORATION has not authorized anyone to make representations or warranties other than the warranty contained herein.
The above warranty is effective for all products manufactured after 10/01/86.
NON-WARRANTY REPAIR RATES J&M CORPORATION reserves the right to change the labor repair rates without prior notice. At the time
of this printing the out-of- warranty repair is $40 per hour for labor only. However, the customer is advised to verify the
current rate when he/she calls customer service to obtain the return authorization number.
FACTORY SERVICE ADDRESS J&M Corporation, 1415 S. Cherry Avenue, Tucson, Arizona, 85713, U.S.A. Tel: [phone] audio@
jmcorp.com www.jmcorp.com
CUSTOMER SERVICE NUMBER 1-800-358-0881
Please complete
WARRANTY REGISTRATION FORM
on the reverse side and send to J&M Corporation