J&M Corporation HCRK-7252GTM-XXR User manual

© 2016 J&M Corporation. All rights reserved. 5/16
ROKKER® XXR Series
7.25” Fairing Speaker
Kit for 1998-2013 Harley®
Street/Ultra/Electraglide
#HCRK-7252GTM-XXR
Installation
Instructions

Installation and Instructions
1. Remove the windshield and outer fairing shell completely.
2. Unplug the spade wire connectors on the back of each of the
stock speakers.
3. Remove the three attachment screws from the back of each
speaker and remove each speaker assembly from the fairing. Discard
the speaker assemblies and the attachment screws.
Note: Do not re-use these screws as they are too long and will
cause damage to your fairing.
4. Remove the remaining socket head bolts from both the left and
right inner fairing support braces.
5. Assemble a J&M speaker grill and a J&M speaker adapter with
the side of the adapter marked “TOP” positioned upward and the
larger (mid-range) grill-mounted speaker pointing inward toward the
radio. (Fig. A&B)
6. Using 3 of the 1 inch screws provided install the grill/adapt-
er assembly into the fairing. Use 2 screws in the upper hole loca-
tions and 1 screw in the lower outer hole location. (Fig. B) Note:
Use 3 screws only per side. DO NOT install a screw in either of
the lower inner hole locations. Permanent fairing damage will
result.
Important Note: There are two different styles of inner fairing
support braces. (Fig. C) First determine which of the two styles you
have, then continue with the remaining instructions for your particular
style of support braces.
Early Style Fairing Support Brace
7. Using 4 of the short self-tapping screws provided, install a J&M
7.25” speaker onto the adapter with the speaker’s crossover assem-
bly and spade terminals pointing inward. (Fig. D)
8. Connect the wires from the grill mounted mid-range speaker and
tweeter to the correct terminals of the crossover assembly mounted
on the back of the 7.25” speaker. (Fig. E)
Fig. A Labeled Top
Fig. B
DO NOT INSTALL
SCREWS IN
THESE HOLES
Fig. C
Early Style Late Style
Fig. D
Fig. F
9. Then connect the terminals from the speaker wires of your
audio system to the correct spade terminals on the back of the J&M
speaker. (Fig. E)
10. Re-install the fairing support brace using the original socket head
bolt and another of the short self-tapping screws provided. (Fig. F)
TW
MR
Tweeter
Midrange
TW
MR
Tweeter
Midrange
Speaker
Wiring
Fig. E

Thank you for the condence you have shown in J&M Corporation by
purchasing one of our innovative products.
If you have any question or comments about this product, you may
contact us at USA 1-520-624-7000 Monday thru Friday, 8:00AM thru
5:00PM Mountain Standard Time.
1415 S. Cherry Avenue
Tucson, AZ 85713 U.S.A.
Tel [phone]
Website: http://www.jmcorp.com
E-mail: [email protected]
11. Repeat steps 5 through 10 for the opposite side speaker
assembly.
Late Style Fairing Support Brace
7. Using 5 of the short self-tapping screws provided, install a
J&M 7.25” speaker onto the adapter with the speaker’s crossover
assembly and spade terminals pointing inward. Include a fairing sup-
port brace adapter on the lower outer corner of the assembly (Fig. G)
8. Connect the wires from the grill mounted mid-range speaker and
tweeter to the correct terminals of the crossover assembly mounted
on the back of the 7.25” speaker. (Fig. E)
9. Then connect the terminals from the speaker wires of your
audio system to the correct spade terminals on the back of the J&M
speaker. (Fig. E)
10. Re-install the fairing support brace using the longer socket-head
bolt and spacer, along with the 10-32 pan head screw provided. (Fig.
H)
11. Repeat steps 5 through 10 for the opposite side speaker assem-
bly.
12. Test each speaker for the proper operation before re-assembling
the fairing, realizing that full sound quality and delity will NOT be
heard until the outer fairing shell is completely re-installed.
Fairing Support
Brace Adapter
Fig. G
Fig. H

WARRANTY REGISTRATION FORM Please fill out this card completely and mail it immediately after purchase. Please be sure that your zip code
and serial number (if applicable) are legible. This will help us to serve you better.
(PLEASE PRINT)
Name ______________________________________________________________________________________________________________________________________________________
Address_____________________________________________________________________________________________________________________________________________________
City _______________________________ _________________________________State __________________________ Zip ______________________________________________________
Motorcycle mOther m E-mail ______________________________________________________________________________________________________
Make ___________________________________________ Model ______________________________________ Year __________________
Product part number ______________________________________________________________________
Serial number (if applicable)________________________________________________________________
Date of purchase _________________________________________________
Name of dealer it was purchased from ____________________________________________________________________________________
Mail to:
J&M Corporation
1415 S. Cherry Avenue
Tucson, AZ 85713
U.S.A.
WARRANTY AND REPAIR INFORMATION
TWO YEAR LIMITED WARRANTY In order to facilitate the servicing of this warranty, the Warranty Registration Form should be filled out and
returned within 10 days of the date of purchase. However, return of the Warranty Registration Form is not a precondition of this warranty,
and this Warranty will be observed by J&M CORPORATION whether or not the Warranty Registration Form is returned,
on the condition that other satisfactory evidence of the date of the original purchase is provided to J&M CORPORATION.
WHO PROVIDES THE WARRANTY? This warranty is provided by J&M CORPORATION.
WHO IS PROTECTED? This warranty is extended only to the original owner of this J&M CORPORATION product and may not be
transferred or assigned.
WHAT IS COVERED AND HOW LONG? This warranty covers all defects in material or workmanship of our product for a period of
2 years from date of original retail purchase. At its option, J&M CORPORATION will repair or replace any defective part(s) or
equipment.
The provisions of the warranty shall not apply to any unit which has been subjected to misuse, neglect, incorrect mechanical or
electrical installation, unauthorized modifications, accident, nor to units which have been repaired or altered outside of our factory.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY In the event that the product does not conform to this warranty, the product
should be shipped prepaid to the J&M CORPORATION service facility. Transportation charges, insurance fees, and labor costs for shipment,
removal, or reinstallation of our product are not covered by this warranty. Loss or damage in shipment is the sole responsibility of the freight
carrier.
FOR YOUR INFORMATION Repair as provided under this warranty is the exclusive remedy of the consumer. J&M CORPORATION shall
not be liable for any incidental or consequential damages or for breach of any express or implied warranty on this product. Except to the
extent prohibited by applicable law, any implied warranty of merchantability or fitness for a particular purpose on this product is limited
in duration to the duration of the warranty. Some states do not allow the exclusion or limitation of incidental or consequential damages,
or allow limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you. This warranty gives
you specific legal rights which vary from state to state.
J&M CORPORATION reserves the right to make changes in design and to make improvements in its products without the obligation to
incorporate the changes or improvements in any of its previously manufactured products.
J&M CORPORATION has not authorized anyone to make representations or warranties other than the warranty contained herein.
The above warranty is effective for all products manufactured after 10/01/86.
NON-WARRANTY REPAIR RATES J&M CORPORATION reserves the right to change the labor repair rates without prior notice. At the time
of this printing the out-of- warranty repair is $40 per hour for labor only. However, the customer is advised to verify the
current rate when he/she calls customer service to obtain the return authorization number.
FACTORY SERVICE ADDRESS J&M Corporation, 1415 S. Cherry Avenue, Tucson, Arizona, 85713, U.S.A. Tel: [phone] audio@
jmcorp.com www.jmcorp.com
CUSTOMER SERVICE NUMBER 1-800-358-0881