JASON Hydrotherapy Integrity User manual

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 1 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
OWNER’S MANUAL
Integrity®Soaking, MicroSilk®, AirMasseur®, Whirlpool Baths
INSTALLATION, OPERATION, AND MAINTENANCE
“TO BE REMOVED FOR USE BY THE OCCUPANT.” 49-1013-001
Date 02/13
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118-2029
www.jasoninternational.com
OWNER’S RECORD
Dealer:
Date Purchased:
Date Installed:
Installer:
PLACE SERIAL NUMBER CARD WITH
PRODUCT CONFIGURATION IN THIS BOX
INSPECTION
Inspect the unit prior to installation. In the event of a
problem, DO NOT install the unit.
All components are factory assembled to the bath and the
unit is water tested and inspected prior to leaving Jason
International, Inc.
If the carton shows sign of damage, inspect the product
before accepting and describe the problem on the Bill of
Lading.
NOTE: Transportation and insurance from Jason’s
factory are the buyer’s responsibility.
Damage sustained in transit is the responsibility of
the carrier. If damage is discovered, the carrier must
be immediately notified in writing with a request for a
representative to inspect the unit. Failure of the carrier
to respond should be reported to the seller and carrier.
Always file a freight claim promptly.
The installer is responsible for ensuring that the unit is
free from defects or shipping damage. In the event of a
problem, DO NOT install the unit.
Jason International is not responsible for damage that
might have been avoided by inspection or testing prior to
installation.
If the carton shows sign of damage, inspect
the product before accepting and describe the
problem on the Bill of Lading.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer.
ALL WARRANTY CLAIMS ON ACRYLIC SURFACE
DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
Inspect plumbing and bath surface for missing or damaged
components. Alert your dealer of any discrepancies.
To protect the unit from damage keep the bath in the
carton until ready for installation.
EQUIPMENT ACCESS
In accordance with Building Codes, service access to
all hydrotherapy bath equipment, controls and electrical
connections must be provided during installation
(Recommended minimum 28" x 17" [71 x 43 cm]).
Insufficient access will hinder repair and maintenance.
Warranty service will not cover costs of providing
equipment access.
Jason offers an optional removable lateral skirt for all
rectangular baths. The skirts are available in matching
acrylic colors and provide convenient access to bath
equipment, as well as an excellent finished appearance.
The Specification Sheet for this bath contains additional
technical information. This sheet can be provided by your
dealer or accessed online at www.jasoninternational.com.

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 2 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
SILICONE BEAD
TILE
DRYWALL DRYWALL
TILE
OPTIONAL
TILE FLANGE
KIT
OPTIONAL
INTEGRATED
TILE LIP
1" X 2"
SUPPORT
SCREW
INSTALLATION INSTRUCTIONS
4. Install the drain and overflow assembly to the bath shell
according to the instructions provided with the drain and
position the bath in the area of intended installation.
5. Finishplumbingrough-inofdrainandoverflowassembly.
Atthistime,considerationsshould bemadefortheposi-
tion and mounting of the faucet set, as well as all related
plumbing.
6. Remove the packing board before installing the
bath. The bath is equipped with separate bath equip-
ment support bases which are joined for shipment with
packingboards.Detachthe packingboardfrom thebath
and from underneath the equipment.
WARNING: Any modification to the equipment is
not recommended and will void the Manufacturer’s
warranty.
7. Installthebathlevelforproperdrainage.Jasonbaths
are designed to be supported at the base of the bath.
If the floor is smooth and level, the baths’ Level Form™
Base will provide proper drainage and support (See
Figure 3).
8. Mortar is required when the subfloor is not smooth and
level;whenadditionalsoundinsulationisdesired;orwhen
the bath is installed in a drop-in application. In alcove
installations,a bedofmortarmayalsoberecommended
to aid in leveling the bath. NOTE: Do not use a sand bed
or foam to install or level the bath.
9. Secure the bottom of all equipment mounts so that it
is level with the bottom of the bath. Position the bath
intheareaofintendedinstallationandcuttheequipment
support strap(s) to allow the equipment to rest firmly on the
floor. We recommend securing the equipment mounts to
the floor with removable fasteners for ease of servicing.
10. Protecttheacrylicbathsurfacefromdamageduring
installation with a suitable material, i.e., cardboard
and/or plastic film. The acrylic surface of this bath has
been provided with a protective film which helps protect
the bath during shipment and installation. Additional
protection may also be required to protect the acrylic
surface during installation. If the bath is tiled in, remove
the necessary portion of the film when installing the tile.
INSTALLATION
See the USER MAINTENANCE INSTRUCTIONS section
of this owner’s manual, prior to installation, for humidity and
mold prevention suggestions.
1. Finish Frame A finish frame under the shell rim should
always be constructed to support the bath deck and en-
sure proper drainage toward the bath well. This frame is
notintendedtosupportthe fullbathweight(see Figures
1 & 2).
Jason offers a removable lateral skirt for most baths.
The skirts are available in matching acrylic colors
and provide convenient access to bath equipment, as
well as an excellent finished appearance. However, if
Jason’s lateral skirt is not used, an access panel MUST
be provided to enable final electrical connections and
service. Please refer to the minimum recommended ac-
cess panel size listed in the Equipment Access Section
of this manual.
If a Jason lateral skirt is to be used, the bath deck must
be leveled at 20.5" (52cm) from the support floor or the
skirt will not fit properly.
CAUTION: Make sure the support frame is drilled
and/or notched as needed to assure that the On/
Off air actuator switch and air tube are not bound
or pinched.
Allowampleclearancefortheequipment.Whirlpools
withoptionalfrontpump mountsmayrequire aminimum
of 1" clearance beyond the front and pump side lip of the
bath to allow clearance of the pump.
CAUTION: Ambient temperature under the bath where
equipment is installed must not exceed 50°C (122°F).
2. 100%Siliconewithmildew-resistantpropertiesshouldbe
appliedbetweenthewater-resistantbackerboardandthe
deckof thebath.NOTE:If youuse atile flange kit, modify
the framing to support the bath lip as shown in Figure 1.
3. For AirMasseur®models, a minimum ventilation open-
ing of 2" x 4" (5 x 10 cm) for the blower is required, and
should be designed to draw in indoor ambient air at a
minimum 22°C (72°F).
Figure 1 Figure 2

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 3 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
OVERFLOW
GROUND - GREEN WIRE
NEUTRAL - WHITE WIRE
HOT - BLACK WIRE
DEDICATED
120V, 60 Hz
GFCI PROTECTED
OUTLET
AIR SWITCH
CONTROL BOX
AIR SWITCH
"DROP LOOP" FULL SUPPORT BASE
AIR SWITCH ACTUATOR
NOTE: THE ABOVE
DIAGRAM CAN ALSO BE
USED FOR 120V, 50Hz
SYSTEMS.
MicroSilk Unit
AIR SWITCH ACTUATOR
AIR SWITCH ACTUATOR
FULL SUPPORT BASE PUMP MOUNT
FULL SUPPORT BASE
Dedicated
120V, 60 Hz
GFCI Protected
Service
L2
L1
GROUND
DEDICATED
240V,50 or 60 Hz
GFCI PROTECTED
SERVICE
NOTE: USE THE ABOVE
DIAGRAM FOR 240V, 50Hz
OR 60Hz SYSTEMS.
GROUND - GREEN WIRE
NEUTRAL - WHITE WIRE
HOT - BLACK WIRE
Dedicated
120V, 60 Hz
GFCI Protected
Service
L2
L1
GROUND
DEDICATED
240V,50 or 60 Hz
GFCI PROTECTED
SERVICE
NOTE: USE THE ABOVE
DIAGRAM FOR 240V, 50Hz
OR 60Hz SYSTEMS.
GROUND - GREEN WIRE
NEUTRAL - WHITE WIRE
HOT - BLACK WIRE
INSTALLATION INSTRUCTIONS (cont.)
Figure 3a
Whirlpool System
Figure 3b
MicroSilk® System
Figure 3c
AirMasseur® System
Export

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 4 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
INSTALLATION INSTRUCTIONS (cont.)
ELECTRICAL
Electrical Power Supply: These instructions are written
assuming 60Hz, 120V power supply. Special notations are
alsoincludedforexportversionsoftheequipmentandpower
supply.
WARNING: Verification of electrical requirements MUST
bemadebeforeinstallation.Refertotheequipmentlabels
for voltage and frequency requirements.
NOTE: Verify that the electrical service matches either the
120v or 240v system requirements for this bath.
NOTE: Thebath is designedfor indoor use only. The electri-
calequipmentmustnotbeexposedtodirectorindirectwater
or moisture contact. The electrical equipment must also be
protectedfromdustand otherairbornedebrisbefore,during,
and after installation.
1. Electrical Service: A licensed electrician must provide
the “dedicated” electrical service protected by a GFCI.
The location of the GFCI must be at least five (5) feet
(152cm)awayfrom theinside surfaceofthe bath,acces-
sible for regular testing. Use copper conductors only.
DANGER—RISKOFELECTRICSHOCK:Connectonly
toacircuitprotectedbyaGroundFaultCircuitInterrupter
(GFCI).Intheunlikelyoccurrenceofacurrentimbalance
inthepowerconductors,theGFCIwillinterruptthepower
to the bath.
WARNING: The electrical service to the GFCI must not
beinterruptedbyanycontroldevice.Likewise,theelectri-
cal service from the GFCI to the bath control should be
directandnotinterruptedbyaswitch.Neveruseaswitch
inconjunctionwithacontroldevice.ThiswillVOID THE
MANUFACTURER’S WARRANTY.
2. GROUNDING IS REQUIRED. The unit should be
installed by a qualified service representative and
properly grounded.
3. INSTALLSERVICECONNECTIONATLEAST6"(15cm)
ABOVE SUB FLOOR.
ALLLOCALANDSTATEELECTRICALANDPLUMB-
ING CODES MUST BE OBSERVED. Where there are
no local codes, the National Electric Code (NEC) and
Uniform Plumbing Code (UPC) shallbeobserved.It is
theresponsibilityoftheinstaller/ownertodeterminespe-
cific code compliance prior to installation of the product.
NOTE:IntheCommonwealthofMassachusetts,installa-
tionis tobe done by aMassachusetts licensedplumber.
DANGER: Do not alter the factory installed wiring.
All building materials and wiring should be routed
away from the equipment or other heat-producing
components of the unit.
4. Whirlpool Equipment
ThisWhirlpoolbathisprovidedwithanAirOn/Offswitch.
The pump is pre-wired to a control box which has a 36"
cord. Connect the pump to a GFCI (Ground Fault Circuit
Interrupter) with the proper service:
Standard Equipment (120V,60Hz).
120V,20A,60Hzelectricalservicewithaserviceground
receptacle dedicated for use by this bath.
Export Whirlpool Equipment (240V,60Hz).
240V,15A,60Hzelectricalservice withaserviceground
receptacle dedicated for use by this bath.
Export Whirlpool Equipment (120V,50Hz).
120V,20A,50Hzelectricalservicewithaserviceground
receptacle dedicated for use by this bath.
Export Whirlpool Equipment (240V,50Hz).
240V, 15A,50Hzelectricalservicewithaservice ground
receptacle dedicated for use by this bath.
5. MicroSilk®Equipment
This MicroSilk®bath is provided with an Air On/Off switch.
The pump is pre-wired to a junction control box which has
a 36" cord. Connect the pump to a GFCI with the proper
service:
Standard Equipment (120v,60Hz).
120V,20A,60Hzelectricalservicewithaserviceground
receptacle dedicated for use by this bath.
Export Whirlpool Equipment (240V,60Hz).
240V,15A,60Hzelectricalservice withaserviceground
receptacle dedicated for use by this bath.
Export Whirlpool Equipment (120V,50Hz).
120V, 20A,50Hzelectricalservicewithaserviceground
receptacle dedicated for use by this bath.
Export Whirlpool Equipment (240V,50Hz).
240V,15A,50Hzelectricalservice with aserviceground
receptacle dedicated for use by this bath
6. AirMasseur®Equipment (120V,60Hz).
This AirMasseur®system comes equipped with an
Air On/Off switch and control box. The blower is pre-
wired with a 36" cord with a NEMA plug end. The air
switch control box and tubing is temporarily secured to
the bath’s plumbing for shipping. During installation the
tubing must be attached to the bath’s air switch actua-
tor and the air switch control box. The air switch control
box should be relocated to its dedicated circuit outlet.
Connect only to a dedicatedGFCI protected,120V, 15A,
60Hz circuit with a service ground. The air switch tubing
must be firmly attached to the air switch control box and
to the air switch actuator. A small bead of silicone may
be added to the air tubing connections to help prevent
the tubing from disengaging. The air switch tub-
ing must also be installed to allow for a “drop loop”
(See Figure 3c). This will prevent any moisture from
enteringtheairswitchcontrolboxfromthetubing.Finally,
the blower will plug into the control box.

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 5 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
INSTALLATION INSTRUCTIONS (cont.)
FIELD INSTALLATION OF THE MICROSILK®PUMP
ASSEMBLY
The Jason MicroSilk®system has been factory assem-
bled following ETL and IAPMO guidelines. For shipping
purposes, on some bath models, the MicroSilk®Pump As-
semblymaybepackagedseparatelyanddisconnectedfrom
the bath.
NOTE: These instructions can also be found in the
Installation, Operation and Maintenance manual of the
separately packaged MicroSilk®therapy bath unit.
WARNING: SYSTEM UNDER PRESSURE – NEVER PER-
FORM MAINTENANCE WHILE SYSTEM IS RUNNING.
Note: Verify the MicroSilk®Pump Assembly is the same unit
that was provided for the bath being installed. The serial
number listed on the label provided on the MicroSilk®Pump
Assemblycartonshouldmatchtheserialnumberofthebath.
Warning: Any modification to the equipment is not
recommended and will VOID the manufacturer’s
warranty.
To install the MicroSilk®Pump Assembly to the bath, the
following procedures must be followed.
Note: Do not install the MicroSilk®Pump Assembly further
than the length of the tubing that is factory installed on the
bath. These tubing lengths have been designed for proper
drainage of the system.
1. Position the bath in the area of intended installation.
2. Before beginning any work, the installer is to determine
the proper location of the MicroSilk®Pump Assembly
and service access.
3. Do not disconnect the plumbing lines that are secured
to the bath with nylon tie straps (Figure 5).
Figure 4
Figure 5
4. Clamp the MicroSilk®Jet Line to the MicroSilk®
Discharge Barb using the clamp provided on the
tubing. Assure the MicroSilk®Jet Line will allow proper
drainage to the Jets (Figure 6). The discharge hose
must have a continuous drop from the discharge barb
to the jet fitting.
5. ClamptheMicroSilk®SuctionLinetotheMicroSilk®Suc-
tionBarbusingtheclampprovidedonthetubing.Assure
the MicroSilk®Suction Line will allow proper drainage
to the suction (Figure 7). The suction hose must have
a continuous drop from the suction barb to the suction
fitting.
Figure 6
Figure 7

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 6 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
6. Clamp the MicroSilk®Drain Line to the MicroSilk®Drain
Barb using the clamp provided on the tubing. Assure
the MicroSilk®Drain Line will allow proper drainage to
the drain fitting (Figure 7). The drain hose must have a
continuous drop from the drain barb to the drain fitting.
Caution: Confirm all tubing is fully engaged on its
respective barb and its clamp has secured the tub-
ing to the barb.
7. The bottom of the Pump Mount must be secured and
level with the bottom of the bath, it is recommended re-
movable fasteners be used in case any future servicing
is required.
8. ContinuebathinstallationpertheJasonOwner’sManual
Installation, Operation, and Maintenance guide.
REMOTE MOUNTING OF AIR BLOWER
The Jason AirMasseur®system has been factory installed
following E.T.L. Guidelines. During installation, if remote
mounting of the blower is desired or required, the following
procedures should be followed.
NOTE: Do not remote mount the blower more than 15
feet (457cm) away from the air inlet of the bath. Choose
a location as close as possible to the bath to assure
maximum efficiency.
1. Make sure the blower is well ventilated. The blower
mount should be attached firmly to the floor. Piping
between the remote blower location and the bath can
be insulated using a minimum of 1/2" (13mm) thick
insulation. Attach new piping to the elbow of the
existing piping.
2. The installer must determine the layout of the pip-
ing; exact remote mount location; and service access
before beginning any work. Use 1.5" (38mm) ABS
or PVC plastic tubing. Locate the blower in an area
accessible for servicing.
NOTE: A 15-foot extension replacement cable
set can be purchased from your Jason supplier,
if needed. To ensure proper functioning of the
system, avoid remote mounting in a location which
requiresmorethansix(6)pipingdirectionchanges.
A 90° direction change should be made up of two
45° elbows for maximum efficiency.
3. If the blower has been factory installed, disconnect the
blower from the air bath plumbing by removing the two
(2) screws on the check valve outlet and disconnect the
short piece of flex pipe between the check valve and
the elbow by removing the two (2) screws in the elbow.
(Omit this step on baths where the blower is not factory
installed and remote mounting is required.)
4. Install the blower in the remote location. The remote
mount locations’ ambient air temperature should remain
at approximately 22°C (72°F) for optimum air heating.
CLEANING
1. Removeallloosedebris.Constructionplasterorexcess
grout can be removed with the use of a wood (edge)
trowel.
2. Paint or tar stains may need to be removed with a
cleaner such as paint thinner, turpentine, or isopropyl
alcohol (rubbing alcohol). Never allow the cleaner to
soak against the acrylic surface for long periods of time.
Always rinse the surface immediately following the
use of cleaners.
3. Follow the manufacturer’s instructions for safe use of
cleaning products. If the surface becomes scratched or
dulled,itmayberestoredbyusingaqualityplasticpolish,
likeNovus Plastic Polish No. 2(available from theJason
Dealer). It is always preferable to protect the acrylic
surface during installation to minimize cleanup and
prevent surface damage.
WATER TESTING
Before finishing the installation, it is recommended that the
bath be water tested and the plumbing tested for leaks.
1. Before water testing the bath, make sure any pump
unions are hand tight. Do not over tighten or use a pipe
wrench. This will damage the unions and cause leaking.
If the unit leaks with the unions hand tight, then loosen
the unions(s) and check the O-ring seal to ensure it is
properly seated.
2. Fill and operate the bath. Close the drain and fill the
bath with water to at least 10 inches [25 cm] below the
bathdeck.Theinlettemperatureshouldnotexceed40°C
(104°F). Refer to the FILLING AND DRAINING section
of this owner’s manual for more information.
NEVER RUN THE PUMP WITHOUT ENOUGH
WATER IN THE BATH TO COVER THE JETS.
3. Inspect the plumbing for leaks.
4. Turn the equipment Off and then drain the water.
The bath unit and its plumbing are designed to drain
after each use whether used as a hydrotherapy bath,
soaking bath, or when taking a shower.
INSTALLATION INSTRUCTIONS (cont.)

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 7 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
OPERATING INSTRUCTION, FEATURES, AND CONTROLS
INTRODUCTION
This manual contains all of the information needed for
the proper installation and operation of this Integrity®
Soaking,MicroSilk®,AirMasseur®,orWhirlpoolbath.Thebath
has been designed to give you years of relaxing trouble-free
service, provided the unit is maintained and operated in ac-
cordance with these instructions.
Thoroughly clean and disinfect the unit as described in the
CLEANINGsectionoftheUSERMAINTENANCEINSTRUC-
TIONSsectionofthis owner’smanual beforeitsfirstuseand
periodically thereafter.
WARNING: Before operating, refer to the instructions
at the end of this owner’s manual pertaining to the risk
of fire, electric shock, or injury to persons.
MICROSILK®OPERATION
All Jason Integrity®MicroSilk®baths are pre-plumbed at
the factory with standard equipment. Standard equipment
includes a Microbubble generator unit, MicroSilk®jet, and
an air actuated On/Off switch.
CAUTION: Keep hair, towels, and clothing away from the
suction fitting whenever the equipment is On. Never operate
the equipment with the suction cover off, as doing so voids
the manufacturer’s warranty. It is a safety cover designed to
eliminate the potential of hair and body entrapment.
Filling and Draining
Close the drain and fill the bath with water at least two (2)
inches (50mm) above the jets. The inlet temperature should
not exceed 40°C (104°F).
CAUTION: NEVER RUN THE MICROSILK PUMP WITHOUT
ENOUGH WATER IN THE BATH TO COVER THE JETS.
Air ON/OFF Button
The Air On/Off button provides a
safe and convenient method for
controlling the MicroSilk®bath.
The Air On/Off button is factory
mounted onto the bath prior to
shipment. See Figure 3b for the
locationoftheAirOn/Offbutton(air
actuator)ontheMicroSilk®bath.Fill
the bath to at least two (2) inches
abovethe jetand press the Air On/
Off button to start the MicroSilk®unit. Press the Air On/Off
button again to stop the MicroSilk®unit.
MicroSilk®Unit
The MicroSilk®unit generates oxygen rich microbubbles
that fill the bath. MicroSilk®units provided on Jason baths
are factory tested when assembled and again retested after
installation on the bath.
MicroSilk®Port
A strategically placed MicroSilk port is provided for com-
plete enjoyment of the bath.
AIRMASSEUR®OPERATION
All Jason Integrity®AirMasseur®baths are pre-plumbed at
the factory with standard equipment. Standard equipment
includes a quiet 3/4 HP, variable-speed blower with integral
heater;20-minutetimer;andAirswitchcontrolswith“On/Off”
and blower speed functions.
Filling and Draining
Close the drain and fill the bath with water to at least 10”
below the bath deck. The maximum recommended bathing
temperature is 40°C (104°F). Before starting the blower, en-
sure that it is plugged into the air switch control box and that
thecontrolbox ispluggedintoits dedicatedelectricalservice
connection. Turn the blower Off before draining the water.
The bath unit and its plumbing are designed to drain after
eachuse,whetherusedasanAirMasseur®orasoakingbath.
AirMasseur®Blower
TheJasonIntegrity®AirMasseur®systemcontainsavariable
speed-controlled heated air blower. The blower provided is
factory tested when assembled onto the bath. The blower
must be plugged into the air switch control box, which must
be plugged into its dedicated GFCI
electricalservicepriortoturningiton.
Air ON/OFF Button
The Air On/Off button (air switch
activator) allows the user to turn the
blower On and Off and controls the
blowers intensity. Momentarily de-
press the Air On/Off button to start
or to stop the air blower. A timer will
automatically stop the air blower
after 20 minutes of operation if it is
not stopped manually.
Blower Speed
Once the blower is On, to decrease the air output, press
and hold the Air On/Off button until the desired intensity is
reached, then release the Air On/Off button. To increase the
air intensity, press and hold the Air On/Off button until the
desiredintensityisreached,thenreleasetheAirOn/Offbutton.
Control Box

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 8 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
OPERATING INSTRUCTION, FEATURES, AND CONTROLS (cont.)
The blowers Air On/Off button control box is built to plug into
the dedicated GFCI electrical circuit. A 36” power cord with
a plug end is prewired to the blower, which must be plugged
into the control box. A built-in timer shuts the blower off
20-minutes after being activated.
Automatic Purge Cycle
Fifteen minutes after the blower is stopped, the blower will
automatically start for two (2) minutes to purge and dry the
air channel system.
WHIRLPOOL OPERATION
All Jason Integrity®Whirlpool baths are pre-plumbed at
the factory with standard equipment. Standard equipment
includes five (5) or more directional hydrotherapy jets, and
an air actuated On/Off switch.
CAUTION: Keep hair, towels, and clothing away from the
suction fitting whenever the equipment is On. Never oper-
ate the equipment with the suction cover off, doing so voids
the manufacturer’s warranty--it is a safety cover designed to
eliminate the potential of hair and body entrapment.
Filling and Draining
Close the drain and fill the bath with water at least two (2)
inches (50mm) above the jets. The inlet temperature should
not exceed 40°C (104°F).
CAUTION: NEVER RUN THE WHIRLPOOL PUMP WITH-
OUT ENOUGH WATER IN THE BATH TO COVER THE
JETS.
Before starting the pump, direct the jet nozzles downward to
preventthepossibilityofwatersplashingfromthebath.When
bath is in use, turn the unit Off before draining the water. The
bath unit and its plumbing are designed to drain after each
use whether used as a hydrotherapy bath, soaking bath, or
just taking a shower.
Air ON/OFF Button
TheAirOn/Offbuttonprovidesasafe
andconvenientmethodforcontrolling
the Whirlpool bath. The Air On/Off
button is factory mounted onto the
bath prior to shipment. See Figure
3a for the location of the Air On/Off
button(airactuator)ontheWhirlpool
bath. Fill the bath to at least two (2)
inches above the highest jet and
press the Air On/Off button to start
thewhirlpoolpump.PresstheAirOn/
Off button again to stop the whirlpool pump.
Whirlpool Jets
Five or more strategically placed whirlpool jets are provided
for complete enjoyment of the bath. The jets are specially
designedformaximumwhirlpoolactionwithdirectionandflow
control.Changingthedirectionofthejetswillconcentratethe
massaging jet stream to the area of preference and turning
the flange of the jet will adjust the amount of flow.
Whirlpool Pump
The pump provided on Integrity®Whirlpool baths is factory
testedwhenassembledontothebath.Thepumpisdesigned
to incorporate high quality, long-life seals which provide su-
perior service. However, should the pump need service, use
thesuctionand dischargeunionsprovided foreasyremoval.
NOTE: If the unit fails to operate, check the breaker
panel to insure that the circuit breaker is on. Check the
GFCI by testing and resetting it. If the unit still fails to
operate, refer to the Trouble Shooting Guide section of
this manual. If the unit still fails to operate and is out of
warranty, contact an authorized service technician for
repair. If the unit is within the warranty period, contact
JASON Technical Services at 800-255-5766. DO NOT
ATTEMPT TO RESOLVE THE PROBLEM.

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 9 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
SURFACE MAINTENANCE
Areas with minor scratches or dull surfaces can be restored
by applying commercially available plastic polish (i.e. Novus
PlasticPolishNo.2,availableatyourJasondealer),followed
byanapplicationofacrylic pastewax. Buff thesurfacewith a
cleansoftcloth.Donotusesandpaper,steelwool,orabrasive
rubbing compounds.
Ifscratchesaretoodeeptorubout,orifthedamagepenetrates
theacrylicsurface,consultyourdealer forrecommendations
on surface repair.
AIR HEATER AND AIR TEMPERATURE
The air heater incorporated into the air blower is designed
to preheat the incoming air to body temperature, not to heat
the bath water. The air heater automatically comes on when
the air blower is activated. Even though all air baths provide
preheated air, occasionally some people with sensitive skin
mightexperienceacoldairsensation.Thissensationiscaused
by the swiftly moving heated air bubbles blowing on the wet
skin. This phenomenon can be related to the use of a fan for
cooling on a hot day. While the ambient temperature does not
change, the moving air makes you feel cooler. Avoiding this
cold air sensation is among the reasons Jason avoids placing
air jets directly beneath the body. If you experience a cool air
sensation,whichismostnoticeableduringthefirstfewminutes
of an air bath, simply move your body slightly away from the
closest jets.
FLUSHING / SANITIZING
Upon start-up and not to exceed 90 days, your bath and
plumbing system should be flushed. To do so, close the drain
and fill the bath with warm water to at least two (2) inches [5.1
cm]abovethehighest jet.PourinJason BathSystemCleaner
and follow the directions on the bottle. DO NOT use bleach or
other chlorinated cleansers directly on the metal trim.
REPAIR
Refer all plumbing or electrical repair to a qualified service
technician.DONOTATTEMPTTORESOLVETHEPROBLEM.
This can result in danger of electrical shock or damage to
the unit and will VOID THE WARRANTY. Remember, when
contacting your dealer or service representative, always have
yourserialnumber,proofofpurchase,andmodelnumber.This
will ensure a quick response on warranty items. The serial
number can be found on the front page of this manual or on
the small card adhered to the back of the bath just above the
equipment.
ALL WARRANTY REPAIRS MUST BE AUTHORIZED BY
THE MANUFACTURER BEFORE WORK IS STARTED
HUMIDITY
Warning: Avoid high humidity levels in your home.
Mold, mildew, fungi and bacteria which may be
harmful to health thrive in areas with continued high
humidity levels; therefore, every precaution should be
taken to make sure your plumbing fixtures, including
bathtubs, hydrotherapy baths, or showers do not
become a source of high humidity due to improper
installations or leaks.
To avoid having your plumbing fixtures become a source
of unwanted humidity, please make sure the following
steps are taken prior to installation.
1. Make sure the area where the bathtub or shower is
installed is well vented and allows enough ventilation
and air circulation to dry the bathroom environment
within a short time after taking a bath or shower.
2. If your bath or shower unit is tiled-in, use units with an
integral tile flange or make sure a tile flange kit or a
similar mechanical barrier is installed to prevent shower
spray, splash, or overflow to leak behind the bathtub.
3. Make sure the plumber properly tests your
hydrotherapy bath before it is roughed in to make sure
there are no leaks and it is installed with proper access
to bath equipment.
4. Make sure that all the plumbing and fixtures in the
bathroom are in good working order and have no leaks.
5. Do not use carpeting or other materials or furniture,
which can hold moisture in your bathroom.
6. Use disinfectant to clean any bathroom surfaces which
are regularly exposed to moisture.
7. Clean and disinfect humidifier and dehumidifiers as
recommended by the manufacturer. Replace the air
filter on the HVAC unit once a month.
8. Clean moldy surfaces as soon as any mold appears
by using a detergent/soapy solution and appropriate
household cleaner. Always use gloves during cleaning.
Dispose of any sponges or rags used to clean mold.
CLEANING
With minimum care, your acrylic-surfaced bath will retain
its high-luster finish for many years. For regular cleaning
use Jason Bath Cleaner or a mild NONABRASIVE liquid
detergent solution (i.e. glass cleaner) and a soft, wet
cloth or sponge. Do not run the hydrotherapy system with
foaming cleaners or soaps. Rinse the bath thoroughly
after cleaning.
USER MAINTENANCE INSTRUCTIONS

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 10 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
TROUBLE SHOOTING GUIDE
If you believe the unit to be within the warranty period, you must contact Jason Customer Service: 1-800-255-5766 with the
bath’s Product and Serial numbers before work is started.
ALL WARRANTY REPAIRS MUST BE AUTHORIZED BY JASON BEFORE WORK IS STARTED.
FOR SERVICE, ALWAYS CONTACT YOUR DEALER OR AUTHORIZED SERVICE CENTER
WARNING: Always turn off power at the mail electrical service panel when servicing the bath.
AIRMASSEUR®BLOWER SYSTEM
SYMPTOMS POSSIBLE CAUSES RECOMMENDED ACTION
Air bath system won’t operate.
a) No power to air bath unit. a) Reset circuit breakers and check GFCI. Check fuses
and replace if bad.
b) Blower motor is not plugged in. b) Make sure plug is fully inserted into the outlet.
c) Air Switch is disconnected or
defective. c) Check and reconnect if necessary.
Blower shuts off by itself or before
time elapses.
a) Blower motor overheated
and thermal protection device
deactivated motor (possibly low
voltage).
a) Check that blower has sufficient ventilation and that the
intake into the blower is not blocked. Clear and allow
the motor to cool down. (Check service & wire size.)
b) GFCI tripped. b) Refer to installer/dealer.
Circuit breaker trips repeatedly.
a) Defective breaker. a) Replace breaker.
b) Short circuit between bath and
blower breaker box. b) Refer to installer/dealer.
c) Other items are connected to
the same circuit. c) Refer to installer/dealer.
Blower does not shut off. a) Defective keypad or timer. a) Refer to installer/dealer. Replace Air Switch or control.
LED light will not operate. a) LED light is loose in socket. a) Access LED light and assure it is properly installed in
socket..
b) LED cable disconnected. b) Verify correct cabel connections.

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 11 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
TROUBLE SHOOTING GUIDE cont’d)
WHIRLPOOL PUMP SYSTEM
SYMPTOMS POSSIBLE CAUSES RECOMMENDED ACTION
Pump system won’t start.
a) No power to the pump unit. a) Reset circuit breakers and check GFCI. Check fuses
and replace if bad.
b) Pump motor is not plugged in. b) Make sure plug is fully inserted into the ourlet.
c) Air Switch is disconnected or
defective. c) Check and reconnect if necessary.
Pump operates, but no air is
injected into water. a) Air line is clogged. a) Refer to installer/dealer.
Pump operates, but water is not
being pumped.
a) Suction or discharge blocked. a) Remove obstruction.
b) Suction air leak. (System usu-
ally surges.) b) Make sure union is tight on suction side of the purmp.
Pump does not manually shutoff. a) Defective keypad or control a) Refer to installer/dealer. Replace keypad or control.
Pump unions leak. a) Unions cracked, under-tight-
ened, over-tightened, or O-ring
is not seated properly (possi-
bly pinched).
a) Refer to installer/dealer. Replace keypad or control.
Pump shuts off by itself.
a) Pump motor overheated and
thermal protection device
deactivated motor. (Possibly
low voltage.)
a) Make sure motor air cooling vents are not blocked.
Clear and allow motor to cool down. (Check service &
wire size.)
b) GFCI tripped. b) Refer to installer /dealer.
c) Water fell below recommended
level. c) Fill to recommended level (2” [50 mm] above jets).
LED light will not operate. a) LED light is loose in socket. a) Access LED light and assure it is properly installed in
socket.
b) LED cable disconnected. b) Verify correct cabel connections.

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 12 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
JASON INTERNATIONAL INC. LIMITED WARRANTY
The Company warrants the products of its own manufacture to be free from defects in
workmanship and material for a period of twelve (12) months from date of installation or
eighteen(18)monthsfromdateofmanufacture,whichevercomesfirst.Anymerchandise
whichupon Companyexamination proves tobe defective undernormal useand service
during the warranty period will be at the Company’s option repaired, replaced or credit
issued in the amount of the invoice value of the defective merchandise. All other types
of remedies are excluded. This warranty extends only to the owner of the originally
installed merchandise. The Company is not responsible for labor or other installation
costs for the repair or replacement of defective merchandise. Company reserves the
right to substitute new or improved equipment on any replacements. The repair or
replacement of equipment shall be F.O.B. point of shipment.
This warranty shall not apply to any merchandise which has been subject to accident,
alteration, abuse, misuse, abrasives, corrosion and/or electrolysis, improper voltage
supply,misapplication,carelesshandling,improperinstallation,maintenance,abnormal
chemical conditions, nor does this warranty cover stains, discoloration or the fading of
color due to improper use of chemicals or improperly maintained water chemistry.
This warranty shall not apply to any merchandise or parts thereof which were not manu-
factured by Company. Such product or merchandise manufactured by others shall have
only such warranties, in writing, that may be extended and in force at the time by such
other manufacturer or supplier.
To obtain warranty service, you must contact the retailer from which the merchandise
waspurchasedorCompany’s distributor in yourarea.Writtennoticeofwarranty defects
mustbegiventothecompanywithinthirty(30)daysfromtheoccurrencethereof.Written
permission must be obtained by the retailer or distributor from the Company before any
equipment claimed defective is returned for inspection.
EXCEPT AS PROVIDED HEREIN, COMPANY MAKES NO WARRANTIES EITHER
EXPRESSED OR IMPLIED, AS TO ANY MATTER WHATSOEVER INCLUDING THE
CONDITION OF THE MERCHANDISE, ITS MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE. ANY WARRANTIES IMPLIED BY LAW AND NOT EF-
FECTIVELY EXCLUDED BY THIS WARRANTY, ARE LIMITED TO THE DURATION
AND REMEDIES OF THIS WARRANTY. IN NO EVENT SHALL THE COMPANY BE
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the
exclusion or limitation of incidental or consequential damages, so the above limitations
may not apply to you.
This warranty gives you specific legal rights and you may also have other rights that
vary from state to state.
WARRANTY REGISTRATION: Register your product's warranty online at www.jasoninternational.com.
Troubleshooting Guide (cont.)
MICROSILK®PUMP SYSTEM
SYMPTOMS POSSIBLE CAUSES RECOMMENDED ACTION
MicroSilk system fails
to operate. a) No power to the MicroSilk unit. b) Motor is not plugged in. a) Reset circuit breakers and GFCI if tripped. Check fuses and replace if bad.
Check voltage at motor when control is on. If no
voltage, the control is defective. If voltage is pres-
ent, motor is defective.
b) Make sure plug is fully inserted into the outlet.
Pump operates, but no
Micro-bubbles are injected
into water.
a) Venturi clogged.
b) Float valve not operating a) Refer to installer/dealer. b) Refer to installer/dealer.
Pump operates, but water
is not being pumped. a) Suction or discharge blocked. b) Suction air leak. (System usually
surges.)
a) Remove obstruction.
b) Make sure connection is tight on suction side
of the pump.
Pump does not manually
shut off. a) Air Switch is disconnected or
defective. a) Check and reconnect if necessary.
Pump shuts off by itself,
or before set time elaps-
es.
a) Pump motor overheated and
thermal protection device deacti-
vated motor. (Possibly low voltage.)
b) GFCI tripped.
c) Water level fell below recom-
mended level.
a) Make sure motor air cooling vents are not blocked,
clear and allow motor to cool down. (Check service &
wire size.)
b) Refer to Jason Customer Service.
c) Fill to recommended level. (4” above jet)
Pump does not turn off. a) Wiring error or control problem. a) Refer to installer / dealer.
Pump leaks at shaft. a) Damaged or defective shaft seal. a) Refer to installer / dealer.
LED Light will not operate a) LED light is loose in the socket.
b) LED cable disconnected. a) Access LED light and assure that it is properly installed in the socket
b) Verify correct cable connections.

*ASON)NTERNATIONAL)NCs 501.771.4477 Page 13 of 12 Customer Service : 800.255.5766
Copyright © 2013 Jason International.
IMPORTANTSAFETYINSTRUCTIONS
INSTRUCTIONSPERTAININGTOTHERISKOFFIRE,ELECTRICSHOCK,ORINJURYTOPERSONS.
Thismanual containsinformation andinstructions forproperoperationand maintenanceof yourtherapy bath. Failureto followthese
instructions could result in personal injury, electrical shock, or fire.
WARNING:When using thisunit, basicprecautions shouldalways befollowed, includingthe following:
READAND FOLLOW ALL INSTRUCTIONS CAREFULLY
DANGER: TOREDUCE THERISK OFINJURY FOLLOWTHESE PRECAUTIONS:
A. Do not permit children to use this product unless they are closely supervised at all times.
B. Usethisunitonlyforitsintendeduseasdescribedinthismanual.Donotuseattachmentsnotrecommendedbythemanufacturer.
C. The water in a therapy bath should never exceed 40°C (104°F). Water temperatures between 38°C (100°F) and 40°C (104°F)
are considered safe for a healthy adult. Use time should be limited to approximately 30 minutes, followed by a shower to cool
down. Longer exposures may result in hyperthermia. The symptoms of this condition are nausea, dizziness and fainting, and it
can be fatal. Lower water temperatures are recommended for extended use (exceeding 10 -15 minutes) and for young children.
D. Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy,
pregnant or possibly pregnant women should limit therapy bath water temperatures to 38°C (100°F).
E. The use of drugs or alcoholic beverages before or during therapy bath use may lead to unconsciousness with the
possibility of drowning. Never use the therapy bath while under the influence of alcohol, anticoagulants, stimulants,
antihistamines, vasoconstrictors, vasodilators, hypnotics, narcotics, or tranquilizers.
F. Persons with a medical history of heart disease, low or high blood pressure, circulatory system problems, or diabetes should
consult a physician before using a therapy bath.
G. Personsusingmedicationshouldconsultaphysicianbeforeusingatherapybathsincesomemedicationmayinducedrowsiness
while other medication may affect heart rate, blood pressure, and circulation.
DANGER: To reduce the risk of injury, enter and exit the bath slowly. Do not operate this unit unless the suction cover is attached over
the suction inlet fitting and the jet assemblies are installed. There should be at least two (2) inches of water above the highest jet
location during therapy bath operation.NEVER RUN UNIT DRY.
WARNING:Never operate electrically connected devices in or near the bath. Never drop or insert any object into any opening.
ThisunitmustbeconnectedtoasupplycircuitthatisprotectedbyaGFCI.Suchadeviceshouldbeinstalledbyalicensedelectrician
and should be tested on a regular basis (at least monthly). To test the GFCI push the TEST button. The GFCI should interrupt the
power. Push the RESET button and the power should be restored. If the GFCI fails to operate in this manner, there is the possibility
of an electric shock. DO NOT USE. Disconnect the unit and have the problem corrected by a qualified service technician.
To avoid the possibility of personal injury and discoloration of the acrylic surface, the inlet water temperature should not exceed
40°C (104°F). The bath should be drained after each use. Each bather should start their bath with fresh water. Do not use oil base
additives in your therapy bath.
CAUTION:Do not use harsh abrasives or solvents for cleaning this unit.
INSTALLER/OWNERBEARS ALL RESPONSIBILITY TO COMPLYWITH ALLSTATE
ANDLOCAL CODES WHEN INSTALLING THISPRODUCT.
SAVETHESE INSTRUCTIONS
JASON INTERNATIONAL, INC.
-AC!RTHUR$RIVEs.ORTH,ITTLE2OCKs!RKANSASs
www.jasoninternational.com