JASON Hydrotherapy AC635PS User manual

Jason International, Inc. • 501.771.4477 Page 1 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
“TO BE REMOVED FOR USE BY THE OCCUPANT.”
49-1011-009
Date 05/2014
OWNER’S MANUAL
AC635PS & AC553PS forma®
Soaking, Airmasseur®& MicroSilk®Baths
INSTALLATION, OPERATION, AND MAINTENANCE
Jason International, Inc.
8328 MacArthur Drive
North Little Rock, AR 72118
www.jasoninternational.com
MADE IN THE U.S.A.
OWNER’S RECORD
Dealer:
Date Purchased:
Date Installed:
Installer:
PLACE SERIAL NUMBER CARD WITH
PRODUCT CONFIGURATION IN THIS BOX
INSPECTION
Inspect the unit prior to installation. In the event of a
problem, DO NOT install the unit.
All components are factory assembled to the bath and the
unit is water tested and inspected prior to leaving Jason
International, Inc.
If the carton shows sign of damage, inspect the product
before accepting and describe the problem on the Bill of
Lading.
NOTE: Transportation and insurance from Jason’s
factory are the buyer’s responsibility.
Damage sustained in transit is the responsibility of
the carrier. If damage is discovered, the carrier must
be immediately notified in writing with a request for a
representative to inspect the unit. Failure of the carrier
to respond should be reported to the seller and carrier.
Always file a freight claim promptly.
The installer is responsible for insuring that the unit is
free from defects or shipping damage. In the event of a
problem, DO NOT install the unit.
If the carton shows sign of damage, inspect
the product before accepting and describe the
problem on the Bill of Lading.
Jason International is not responsible for damage that
might have been avoided by inspection or testing prior to
installation.
Damage to the unit during installation will not be covered
by warranty and is the responsibility of the installer.
ALL WARRANTY CLAIMS ON ACRYLIC SURFACE
DAMAGE MUST BE MADE PRIOR TO INSTALLATION.
Inspect plumbing and bath surface for missing or damaged
components. Alert your dealer of any discrepancies.
To protect the unit from damage keep the bath in the
carton until ready for installation.
EQUIPMENT ACCESS
In accordance with Building Codes, service access
to all therapy bath equipment, controls and electrical
connections must be provided during installation
(Recommended minimum 28" x 17" [71 x 43 cm]).
Insufficient access will hinder repair and maintenance.
Warranty service will not cover costs of providing
equipment access.
The Specification Sheet for this bath contains additional
technical information. This sheet can be provided by your
dealer or accessed online at www.jasoninternational.com.

Jason International, Inc. • 501.771.4477 Page 2 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS
Figure 1
Figure 2
AC635PS AC553PS
INSTALLATION
Remove the product from its packaging. Read the entire
instructions prior to installing this product.
See the USER MAINTENANCE INSTRUCTIONS section of
this owner’s manual prior to installation for humidity and
mold prevention suggestions.
1. Remove the packing board from the skirt by placing the
bath and skirt assembly upside down and remove the four
press-in fasteners. See Figure 1.
Caution: Place bath deck on a surface that will not
scratch the acrylic surface of the bath.
2. Disassemble the bath from its skirt by removing the four (4)
nuts and washers located at the bottom of the bath with a
½" open ended wrench. Lift the skirt out of the bath. Place
the skirt and the bath in an upright position next to each
other. See Figure 1.
3. Set aside the template and locating stud kit, these will
be used later.
For AirMasseur®baths, remove the blower with stand,
check valve, tubing with (2) clamps, Sani Design™ Cleaning
System kit and electronics from the separate blower carton.
Set aside to be installed later.
For baths with the AEC Equipment Cabinet, set the AEC
carton aside to be installed later
4. Cardboard bath-well protector. Each bath is provided
with a cardboard bath-well protector that should be kept in
the unit throughout the bathroom construction process.
Note: Overflow drains, fill spouts, and valves must be
installed according to the instructions herein.
5. Installation template. An installation template is provided
to locate the floor drain position, sump area position, locat-
ing studs, remote blower tubing floor cutout position (when
applicable), water inlet stub-out position and skirt center
lines. Tape the template to the sub-floor in the desired loca-
tion.
6. Mark on the sub-floor the sump area position, the water
inlet stub-out position, and the remote blower-tubing floor
cut out position (when applicable). One remote blower
tubing, floor cutout position and four (4) water inlet stub-out
positions have been indicated on the template. Choose the
water inlet stub-out position that is preferable for your instal-
lation.
7. Remove the template and cut out the floor.
CAUTION: The floor drain location must be installed
according to the template. This location is critical to
the proper installation of this product.
Note: You must keep the template; it will be needed
during the next step of the installation process.
Note: Refer to Figure 2 to determine which cut-outs are
designed for use with your particular model.

Jason International, Inc. • 501.771.4477 Page 3 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
Figure 3
Figure 4
8. After the finished floor is installed, position the installation
template on the finished floor. Place the template to line up
with the existing floor drain location and orient the template
to the desired position.
Note: The sump area location cutout and remote
blower tubing floor location cutout (when applicable),
and water inlet stub-out must line up with the template.
Note: The Sani-Design™ cleaning system (for AirMas-
seur®baths) has not been installed. See the forma®
Collection FIELD INSTALLATION INSTRUCTIONS for
the installation procedures.
9. Tape the template to the finished floor; using care to align
both center lines and assure that the template is lying flat on
the floor.
10. Transfer the center lines of the template to the finished
floor.
CAUTION: Use a marker that can be removed from the
finished floor after installation.
11. Position the Skirt (only) and align it with the centerlines on
the finished floor. Use the four existing 3/8" holes located
in the bottom four corners of the skirt to mark where to drill
the pilot holes for the four locating studs. If installing on a
wooden floor, 1/4" [6mm] holes are required, and a 5/16"
nut to install the locating studs into the wooden floor. When
installing on a cement slab, 3/8" [9.5mm] holes are required.
See Figure 3. After marking the hole locations, remove the
skirt and set aside.
12. Dry fit the drain and overflow to the bath.
a. Dry fit the drain and overflow to the bath. Use the
instructions included with the drain and overflow to
determine proper fit. It is recommended that flex
PVC pipe be used between the overflow and drain.
This will assure there is enough clearance between
the bath shell and the skirt for the drain.
b. Position bath in place and attach the drain and
overflow to the floor drain “P” trap. CAUTION:
Only dry fit the drain and overflow tee to the
“P” trap at this time.
c. Disconnect the drain and overflow from the bath
and leave the drain assembly free standing in the
“P” trap.
13. Align the drain with the center line on the template.
See Figure 4.
14. Permanently attach the drain tee to the “P” trap.
15. Remove the template from the floor.
16. Install the skirt location studs into the four (4) posi-
tions in the floor. See Figure 5.

Jason International, Inc. • 501.771.4477 Page 4 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
Figure 5
Figure 7
Figure 6
17. Attach faucet accessories to the bath (if applicable).
CAUTION: There is not enough room to mount a deck
mounted diverter valve on the deck of the bath.
If a hand-held shower is desired consider a floor mounted
faucet or a faucet with an above deck diverter.
If a floor mounted faucet is desired, be sure to install the
faucet to allow for sufficient overhang into the well of the
bath. This will ensure an unobstructed water flow out of the
faucet when filling the bath. Follow the faucet manufacturer’s
installation instructions.
18. Flex plumbing. Attach stainless steel flex plumbing to the
deck-mounted faucet (if applicable).
Note: Flex plumbing lines must be long enough so the
bath can be removed from the skirt if access is re-
quired in the future.
½" [12mm] 4 foot [122cm] stainless steel flex hoses may be
purchased from Jason International, Inc.
19. Remote Mounting of Blower. If the blower for the AirMas-
seur bath is to be remote mounted, refer to the REMOTE
MOUNTING OF AIR BLOWER section of this manual,
before proceeding to the next step.
20. Reattach the skirt to the bath by positioning the skirt on
the bath and fastening the 5/16" nut and washers to the
5/16” leveling bolts, nuts and washers attached to the bath.
Be sure that the skirt is positioned correctly allowing the PS
skirt clips to rest against the back of the skirt.
21. Position the bath and skirt assembly over the four locat-
ing studs. Align the drain and overflow with the correspond-
ing bath holes. See Figure 6.
Place bath and skirt assembly on raised blocks approxi-
mately 8" tall.
22. Flex Plumbing. Attach stainless steel flex plumbing to stub-
outs (if applicable). Faucetry connections should be tested
for leaks at this time.
23. Route cables. When applicable, route any electronic
cables through the floor cutout and make the appropriate
connections to the control box. See the CONTROL BOX
CONNECTIONS section of this manual for locations.
24. Remove blocks and place bath and skirt assembly in posi-
tion.
Jason baths are designed to be supported at the base of
the bath. If the floor is smooth and level the bath’s Level
Form™ base will provide proper drainage and support.
See Figure 7.
Note: Do not use a sand bed to install or level the bath.
Note: The bottom of the bath’s Level Form™ base must
be 1/8" lower than the bottom of the skirt.

Jason International, Inc. • 501.771.4477 Page 5 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
Figure 8
ELECTRICAL
Electrical Power Supply: These instructions are written
assuming 60Hz, 120V power supply. Special notations are
also included for the Export versions of the control equip-
ment, and power supply.
WARNING: Verification of electrical requirements
MUST be made before installation. Refer to the equip-
ment labels for voltage and frequency requirements.
NOTE: The bath is designed for indoor use only. The elec-
trical equipment must not be exposed to direct or indirect
water or moisture contact. The electrical equipment must
also be protected from dust and other airborne debris be-
fore, during, and after installation.
1. Electrical Service: A licensed electrician must pro-
vide the “dedicated” electrical service protected by a
GFCI. The location of the GFCI must be at least five (5)
feet (152 cm) away from the inside surface of the bath,
accessible for regular testing. Use copper conductors
only.
DANGER — RISK OF ELECTRIC SHOCK: Connect
only to a circuit protected by a Ground Fault Circuit
Interrupter (GFCI). In the unlikely occurrence of a cur-
rent imbalance in the power conductors, the GFCI will
interrupt the power to the bath.
WARNING: The electrical service to the GFCI must
notbeinterruptedbyanycontroldevice.Likewise,the
electrical service from the GFCI to the bath control
shouldbedirectandnotinterruptedbyaswitch.Never
use a switch in conjunction with a control device.
ThiswillVOIDTHEMANUFACTURER’SWARRANTY.
2. GROUNDING IS REQUIRED. The unit should be
installed by a qualified service representative and
properly grounded.
3. INSTALL SERVICE CONNECTION AT LEAST 6"
(15cm) ABOVE SUB FLOOR.
ALL LOCAL AND STATE ELECTRICAL AND
PLUMBING CODES MUST BE OBSERVED. Where
there are no local codes the National Electric Code
(NEC) and Uniform Plumbing Code (UPC) shall be ob-
served. It is the responsibility of the installer/owner to
determine specific code compliance prior to installation
of the product.
NOTE: In the Commonwealth of Massachusetts,
installation is to be done by a Massachusetts licensed
plumber.
25. Drain and overflow. Complete the installation of the
drain and overflow per the instructions included with
the drain and overflow.
26. Test bath controls. Before finishing the installation,
it is recommended that the bath controls be tested
without filling the bath with water to assure that all
electric connections are properly working.
Note: Refer to the Electrical section for correct
installation of electrical components.
Note: Refer to the Product Test Diagnostics in
the Operating, Features, and Controls section for
testing.
27. It is recommended that the bath be water tested (filled
and operated), and the bath be inspected for leaks
Refer to the FILLING AND DRAINING Instructions
in the Features and Controls section of this owner’s
manual.
28. Seal the joint between the skirt bottom and the floor
with a silicone caulk. See Figure 8.

Jason International, Inc. • 501.771.4477 Page 6 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
4. AirMasseur®Equipment
The AirMasseur®equipment may be shipped separately
from the bath. The blower is prewired to the control box.
Thecontrolboxhasa36"(91cm)cordwithplugend(junc-
tion box connection for 240V). The blower control box is
mounted on a stand. During installation, the control box
stand and controls must be positioned horizontally and
located to permit access for inspection and servicing.
INSTALLATION INSTRUCTIONS (cont.)
120V Electrical Service - AirMasseur®Control Box.
The blowercontrolbox must be pluggedinto a dedicated
120V, 15A, 60Hz, GFCI protected circuit. See Figure 9.
240V Electrical Service - AirMasseur®Control Box
(Export). The blower control box must be plugged into a
dedicated240V,15A,50or60Hz,GFCIprotectedcircuit.
See Figure 9.
Control Box
Light Cable
Check Valve
Blower
Blower Mount
Keypad Cable
Ground - Green Wire
Neutral - White Wire
Hot - Black Wire
Dedicated
120V, 50 or 60 Hz
GFCI Protected
Service
L2
L1
GROUND
DEDICATED
240V,50 or 60 Hz
GFCI PROTECTED
SERVICE
NOTE: USE THE ABOVE
DIAGRAM FOR 240V, 50Hz
OR 60Hz SYSTEMS.
Figure 9
AirMasseur®
Floor Installation
Figure 9a
AirMasseur®
Below floor installation
O
R
Standard / Premier
Edition Signature Edition
Control Box
Light Cable
Keypad Cable
Low Water/Temp Cable
(Signature Edion)
Check Valve
Blower
Blower Mount
Ground - Green Wire
Neutral - White Wire
Hot - Black Wire
Dedicated
120V, 50 or 60 Hz
GFCI Protected
Service
L2
L1
GROUND
DEDICATED
240V,50 or 60 Hz
GFCI PROTECTED
SERVICE
NOTE: USE THE ABOVE
DIAGRAM FOR 240V, 50Hz
OR 60Hz SYSTEMS.

Jason International, Inc. • 501.771.4477 Page 7 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
5. MicroSilk Equipment
The MicroSilk equipment will be shipped separate from
the bath with the AEC Equipment Cabinet. Follow the
instructionsfortheAECEQUIPMENTCABINETINSTAL-
LATION section of this owner’s manual. The control box
has a 36" (91cm) cord with plug end (junction box con-
nection for 240V). The MicroSilk control box is mounted
on a stand.
120V Electrical Service MicroSilk®Control Box. The
MicroSilk control mustbepluggedintoadedicated 120V,
20A, 60Hz, GFCI protected circuit. See Figure 10.
INSTALLATION INSTRUCTIONS (cont.)
240VElectricalService- MicroSilk®ControlBox.The
MicroSilk controlmustbe pluggedintoa dedicated 240V,
15A, 60Hz, GFCI protected circuit. See Figure 10.
DANGER: Do not alter the factory installed wiring.
All building materials and wiring should be routed
away from the equipment or other heat-producing
components of the unit.
Figure 10
Control Box
Dedicated
120V, 50 or 60 Hz
GFCI Protected
Service
Ground
L2
L1
Dedicated
240V, 50 or 60 Hz
GFCI Protected
Service
L2
L1
GROUND
DEDICATED
240V,50 or 60 Hz
GFCI PROTECTED
SERVICE
NOTE: USE THE ABOVE
DIAGRAM FOR 240V, 50Hz
OR 60Hz SYSTEMS.
Control Box
Ground - Green Wire
Neutral - White Wire
Hot - Black Wire
m
MICROSILK™m
Standard / Premier
Edition Signature Edition

Jason International, Inc. • 501.771.4477 Page 8 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
REMOTE MOUNTING OF AIR BLOWER
The Jason AirMasseur®system has been factory installed
following E.T.L. guidelines. During installation, if remote
mounting of the blower and its control box is desired, follow
these procedures.
Note: Do not remote mount the blower and control box more
than 15 feet [457 cm] away from the air inlet of the bath.
Choose a location as close as possible to the bath to assure
maximum efficiency.
1. Determinelayout.Theinstalleristodeterminethelayout
of the piping, exact remote mount location, and service
access before beginning any work.
a. Use 1.5" [38 mm] ABS or PVC plastic tubing.
b. Locate the control box with the blower in an area
accessible for servicing.
c. To ensure proper functioning of the system, avoid
remote mounting in a location which requires more
than six (6) piping direction changes. A 90° direction
change should be made up of two 45° elbows for
maximum efficiency.
2. Install the blower and control box in the remote
location.
a. A minimum ventilation opening of 2" x 4"
[5 cm x 10 cm] for the blower is required, and should
be designed to draw in indoor ambient air at a mini-
mum of 72°F (22°C).
b. Attach the blower mount firmly to the floor.
c. Attach the piping to the blower’s check valve. Use
screwstoattachthepipetothecheckvalveandroute
the hose to the remote blower tubing floor cutout
location.
CAUTION: Do NOT use ABS or PVC glue near
the blower, it could ignite and cause a fire.
3. Attach hose. Attach one end of the blower hose to the
bath connection with the included clamp.
4. Pipe stub out. Extend piping stub-out through the floor
as illustrated in Figure 9. Piping between the remote
blower location and the bath can be insulated using a
minimum of 1/2" [12 mm] thick insulation.
WARNING:Anymodificationtotheequipmentisnot
recommendedandwillVOIDTHEMANUFACTURER'S
WARRANTY.
5. Attach hose. Attach the other end of the hose to the
1-1/2" [38 mm] PVC pipe that is plumbed to the blower
with the included clamp.
6. Route cables. Route the keypad cable, low water level/
temperature sensor cable (if applicable), and the light
cable through the floor cutout to be connected to the
control box.
WARNING: When routing cables, do not allow the
cable to be pinched under the bath shell.
Use the tie buttons attached to the bath to support the
cables.
Note:Aminimumof4feet[122cm]ofhoseandcable
must be free from binding to allow for pulling the
cables back up through the floor cutout.
During installation if it is preferred to run the blower
hose on top of the floor, a 2 1/2" [6.35 cm] diameter
hole can be drilled at the bottom of the skirt. A means
to cover the hole, hose, and wires is not provided.
See Figure 9.
7. Returntothebathinstallationsectiontofinishinstallation
of the freestanding bath.

Jason International, Inc. • 501.771.4477 Page 9 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
Figure 11
Figure 12a
Figure 12b
Figure 13a
Bath Skirt Access
Opening
CAUTION: Do not allow the cabinet to touch the bath or
the skirt. This could produce excessive noise.
ThePVCtrim,aroundtheopeninginthecabinet,hasaflexible
sweep and is used to help obscure the plumbing between
the enclosure and the skirt.
3. Remove the four (4) decorative caps and screws
on the bottom sides of the cabinet and lift the cabinet
off of the metal frame and set it aside. Use the (4)
included #12 screws to attach the frame to the floor.
See Figure 13.
ACRYLIC EQUIPMENT CABINET INSTALLATION
The Jason Acrylic Equipment Cabinet (AEC ) can be
used to house the bath equipment that cannot be remote
mounted away from the bath. The cabinet is standard on
freestanding MicroSilk®baths and is available as an op-
tion for freestanding AirMasseur®baths. To install the AEC,
follow these procedures
1. Remove the preassembled AEC assembly from the
box and detach all components from the packing board
by removing the tie straps. See Figure 11.
2. Place the AEC assembly only in the front of the bath
skirt access opening. The center of the cabinet should
be aligned with the center of the opening leaving a 1/8"
gap between the top of the cabinet and the bath skirt.
See Figure 12.

Jason International, Inc. • 501.771.4477 Page 10 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
Figure 13b
4. Place the equipment inside the frame and attach all
the plumbing and electrical connections. See Figure
14a for AirMasseur®and 14b for MicroSilk®baths.
Note: The electrical service can be provided inside or
outsidetheenclosure.RefertotheELECTRICALsection
of this manual for service requirements. If the service is
outsidethecabinet,positioncordthroughtheslotprovided
in the frame and enclosure.
5. For MicroSilk baths, clamp the plumbing lines to the
appropriate barb using the clamp provided. Assure
the line will allow proper drainage to the bath fitting. The
hose must have a continuous drop from the barb to the
fitting. See Figure 14c.
Figure 14b
Figure 14c
6. Refer to faucet manufacturer’s installation instruc-
tions if a faucet is intended to be mounted on the top of
thecabinetandpositiontheplumbingstuboutsinsidethe
cabinet.
Caution: Use long enough stainless steel flexible
hose to lift the enclosure up to provide access for
disassembly in the future. Be sure to install a faucet
thatwillreachthewellofthebathfromtheenclosure.
Refer to the bath specification sheet for deck width
dimensions.
7. Fill the bath and test all connections for leaks.
8. Place cabinet on the frame and attach with the four (4)
screws and decorative caps.
Figure 14a

Jason International, Inc. • 501.771.4477 Page 11 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
CLEANING
1. Removeallloosedebris.Constructionplasterorexcess
grout can be removed with the use of a wood (edge)
trowel.
2. Paint or tar stains may need to be removed with a
cleaner such as paint thinner, turpentine, or isopropyl
alcohol (rubbing alcohol). Never allow the cleaner to
soak against the acrylic surface for long periods of time.
Always rinse the surface immediately following the
use of cleaners.
3. Follow the manufacturer’s instructions for safe use of
cleaning products. If the surface becomes scratched or
dulled,itmayberestoredbyusingaqualityplasticpolish,
like Novus Plastic Polish No. 2 (available from the Jason
Dealer). It is always preferable to protect the acrylic
surface during installation to minimize cleanup and
prevent surface damage.
WATER TESTING
Before finishing the installation, it is recommended that the
bath be water tested and the plumbing tested for leaks.
1. Before water testing the bath, make sure all plumbing
connections are tight. DO NOT OVERTIGHTEN.
2. Fill and operate the bath. Close the drain and fill the
bath with water to at least 10 inches [25 cm] below the
bathdeck.Theinlettemperatureshouldnotexceed40°C
(104°F). Refer to the FILLING AND DRAINING section
of this owner’s manual for more information.
NEVER RUN THE PUMP WITHOUT ENOUGH
WATER IN THE BATH TO COVER THE JETS.
3. Inspect the plumbing for leaks.
4. TurntheequipmentOffandthendrainthewater.The
bathunitanditsplumbingaredesignedtodrainaftereach
use whether used as a hydrotherapy bath, soaking bath,
or when taking a shower.

Jason International, Inc. • 501.771.4477 Page 12 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
AIRMASSEUR®CONTROL BOX CONNECTIONS
STANDARD EDITION AIRMASSEUR®
Jason’s Standard Edition AirMasseur®system features
the best in luxury bathing for the leisure bath industry. To
assure that your bath functions properly the blower control
must be properly connected.
NOTE: For 120V systems, the power cord for the blower
control box must be plugged into a 120V, 15 amp, GFCI
dedicated circuit.
Figure 15
Blower
C
IMC-213
Keypad
B
A
To Dedicated
120V / 60Hz 15A
GFCI Protected Service
C
Control Box
NOTE: This diagram also applies to 50 Hz, 240V controls,
and power supply systems. Except that the Blower junction
box must be connected into one dedicated 240V, 15 amp,
GFCI circuit.
The AirMasseur® Control Box
The blower and keypad must be plugged into the proper
receptaclesforcorrect operationofthe AirMasseur®system.
See Figure 15 for connections:
(A) The power cord for the AirMasseur®control box must
be connected into the proper GFCI dedicated circuit for the
system (see note).
(B) The blower’s power cord will need to be plugged into the
controlbox RefertotheELECTRICALsectionofthismanual
for connecting the pump to the control box.
(C) Eight-pin mini-DIN terminal for the AirMasseur®Keypad.

Jason International, Inc. • 501.771.4477 Page 13 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
PREMIER EDITION AIRMASSEUR®
Jason’s Premier Edition AirMasseur®system incorporates
all the features of the Standard Edition system and
includes the benefits of ozone sanitation system, and
an LED Chromatherapy light. To assure that your bath
functions properly, the blower control box must be properly
connected.
NOTE: For 120V systems, the power cord for the blower
control box must be plugged into a 120V, 15 amp, GFCI
dedicated circuit.
Figure 16
NOTE: This diagram also applies to 50 Hz, 240V controls,
and power supply systems. Except that the Blower junction
box must be connected into one dedicated 240V, 15 amp,
GFCI circuit.
Blower
D
C
Ozone
IMC-213
LEDs
Keypad
B
A
To Dedicated
120V / 60Hz 15A
GFCI Protected Service
C
D
Control Box
The AirMasseur® Control Box
The blower, keypad, LED light, and Ozone Sanitation Unit
must be plugged into the proper receptacles for correct
operation of the AirMasseur®system. See Figure 16 for
connections:
(A) The power cord for the AirMasseur®control box must
be connected into the proper GFCI dedicated circuit for the
system (see note).
(B) The blower’s power cord should be plugged into the
female cord connection on the ozone unit, prewired to the
control box.
(C)Eight-pinmini-DIN terminalforthe AirMasseur®Keypad.
(D) Six-pin mini-DIN terminal for LED light.
INSTALLATION INSTRUCTIONS (cont.)

Jason International, Inc. • 501.771.4477 Page 14 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
SIGNATURE EDITION AIRMASSEUR®
Jason’s Signature Edition AirMasseur®system is the most
advanced bath manufactured by Jason International, Inc.
and features the ultimate in luxury bathing for the leisure
bath industry. The blower control box must be properly
connected for the bath to function correctly.
NOTE: For 120V systems, the power cord for the blower
control box must be plugged into a 120V, 15 amp, GFCI
dedicated circuit.
Figure 17
Blower
D
C
Ozone
IMC-213
LEDs
Keypad
B
A
To Dedicated
120V / 60Hz 15A
GFCI Protected Service
C
D
E
Water/
Temp
Sensor
Remote
E
Control Box
The AirMasseur® Control Box
The blower, keypad, LED light, Ozone Sanitation Unit and
Water Level/Temperature Sensor must be plugged into the
proper receptacles for correct operation of the AirMasseur®
system. See Figure 17 for connections:
(A) The power cord for the AirMasseur®control box must
be connected into the proper GFCI dedicated circuit for the
system (see note).
(B) The blower’s power cord should be plugged into the
female cord connection on the ozone unit, prewired to the
control box.
(C) Eight-pin mini-DIN terminal for the AirMasseur®Keypad.
(D) Six-pin mini-DIN terminal for LED light.
(E) Six-pin mini-DIN terminal for installation of the water
sensor to the control box.
NOTE: This diagram also applies to 50 Hz, 240V controls,
and power supply systems. Except that the Blower junction
box must be connected into one dedicated 240V, 15 amp,
GFCI circuit.

Jason International, Inc. • 501.771.4477 Page 15 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
Figure 18
STANDARD EDITION MICROSILK®
Jason’s Standard Edition MicroSilk®system features the
best in luxury bathing for the leisure bath industry. To
assurethatyourbathfunctionsproperly,theMicroSilk®pump
control box must be properly connected.
NOTE: For 120V systems, the power cord for the
MicroSilk®control box must be plugged into a 120V,
20 amp, GFCI dedicated circuit.
MICROSILK®CONTROL BOX CONNECTIONS
NOTE: This diagram also applies to 50 Hz, 240V pumps, controls,
and power supply systems. Except that the MicroSilk®Pump
junction boxes must be connected into one dedicated 240V, 20
amp, GFCI circuit.
IMC-263
To Dedicated
120V / 60Hz 20A
GFCI Protected Service
MS Standard 2014
A
B
C
C
MS
Pump
Keypad
Control Box
INSTALLATION INSTRUCTIONS (cont.)
The MicroSilk®Control Box
The MicroSilk®unit and keypad must be plugged into the
proper receptacles for correct operation of the MicroSilk®
system. See Figure 18 for connections:
(A) The power cord for the MicroSilk®control box must be
connected into the proper GFCI dedicated circuit for the
system (see note).
(B)TheMicroSilk®pump’spowercordwillneedtobeplugged
into the control box Refer to the ELECTRICAL section of
this manual for connecting the pump to the control box.
(C) Eight-pin mini-DIN terminal for the MicroSilk®Keypad.

Jason International, Inc. • 501.771.4477 Page 16 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
INSTALLATION INSTRUCTIONS (cont.)
PREMIER EDITION MICROSILK®
Jason’s Premier Edition MicroSilk®system incorporates all
the features of the Standard Edition system and includes
the benefits of an ozone sanitation system and an LED
Chromatherapy light kit. To assure that your bath func-
tions properly, the MicroSilk®control box must be properly
connected.
NOTE: For 120V systems, the power cord for the
MicroSilk®control box must be plugged into a 120V,
20 amp, GFCI dedicated circuit.
NOTE: This diagram also applies to 50 Hz, 240V pumps, controls,
and power supply systems. Except that the MicroSilk®Pump
junction boxes must be connected into one dedicated 240V, 20
amp, GFCI circuit.
Figure 19
IMC-263
MS Premier 2014
A
To Dedicated
120V / 60Hz 20A
GFCI Protected Service
C
C
D
D
B
Ozone
MS
Pump
LEDs
Keypad
Control Box
The MicroSilk®Control Box
The MicroSilk®unit, keypad, LED light, and Ozone Sanita-
tion Unit must be plugged into the proper receptacles for
correct operation of the MicroSilk®system. See Figure 19
for connections:
(A) The power cord for the MicroSilk®control box must be
connected into the proper GFCI dedicated circuit for the
system (see note).
(B) The MicroSilk®pump’s power cord should be plugged
into the female cord connection on the ozone unit, prewired
to the control box.
(C) Eight-pin mini-DIN terminal for the MicroSilk®Keypad.
(D) Six-pin mini-DIN terminal for LED light.

Jason International, Inc. • 501.771.4477 Page 17 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
CONTROL BOX CONNECTIONS (cont.)
SIGNATURE EDITION MICROSILK®
Jason’s Signature Edition MicroSilk®system is the most
advanced bath manufactured by Jason International, Inc.
and features the ultimate in luxury bathing for the leisure
bath industry. The MicroSilk®control box must be properly
connected for the bath to function correctly.
NOTE: For 120V systems, the power cord for the
MicroSilk®control box must be plugged into a 120V,
20 amp, GFCI dedicated circuit.
Figure 20
LEDs
Ozone
MS
Pump
MS Signature 2014
A
To Dedicated
120V / 60Hz 20A
GFCI Protected Service
Control Box
Keypad
C
D
B
ED
C
IMC-213
E
Water/
Temp
Sensor
Remote
The MicroSilk®Control Box
TheMicroSilk®unit,keypad,LEDlight,OzoneSanitationUnit
and Water Level/Temperature Sensor must be plugged into
theproper receptaclesforcorrectoperationof theMicroSilk®
system. See Figure 20 for connections:
(A) The power cord for the MicroSilk®control box must be
connected into the proper GFCI dedicated circuit for the
system (see note).
(B) The MicroSilk®pump’s power cord should be plugged
into the female cord connection on the ozone unit, prewired
to the control box.
(C) Eight-pin mini-DIN terminal for the MicroSilk®Keypad.
(D) Six-pin mini-DIN terminal for LED light.
(E) Six-pin mini-DIN terminal for installation of the water
sensor to the MicroSilk®control box.
NOTE: This diagram also applies to 50 Hz, 240V pumps, controls,
and power supply systems. Except that the MicroSilk®Pump
junction boxes must be connected into one dedicated 240V, 20
amp, GFCI circuit.

Jason International, Inc. • 501.771.4477 Page 18 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
OPERATING INSTRUCTIONS, FEATURES, & CONTROLS
INTRODUCTION
This manual contains all of the information needed for the
proper installation and operation of your Jason bath. The
bathhasbeendesignedtogiveyouyearsofrelaxingtrouble-
free service, provided the unit is maintained and operated in
accordance with these instructions. Thoroughly clean and
disinfect the unit as described in the CLEANING section of
theUSERMAINTENANCEINSTRUCTIONSsectionofthis
owner’smanualbeforeitsfirstuseandperiodicallythereafter.
All Jason baths are pre-plumbed at the factory.
WARNING: Before operating, refer to the instructions
at the end of this owner’s manual pertaining to the risk
of fire, electric shock, or injury to persons.
AIRMASSEUR®OPERATION
STANDARD AND PREMIER EDITION AIRMASSEUR®
The Jason Standard Edition AirMasseur®bath includes a
variable-speed,1-HPairblowerwithheater,automaticpurge
cycle; and three (3) massage modes: Continuous, Wave, or
Pulse; an electronic control; and a 20-minute timer.
TheJasonPremierEditionAirMasseur®bathprovidesallthe
features of the Standard Edition with the included benefits
of a LED Chromatherapy Mood Light, and an Ozone Sanita-
tion system.
Standard/Premier Touchpad
One main control touchpad mounted on the bath deck
contains several icons used by the bather to control the
blower, and LED mood light. A built in timer shuts the
blower off 20 minutes after being activated.
Standard/Premier Automatic Purge
Fifteen (15) minutes after the control has shut off the
blower will start again for a two-minute purge cycle that
dries the air channel. Note that the blower light will flash
during the 15-minute pause before the purge cycle begins.
Once the purge cycle begins, all indicators will light and
the keypad operation will be disabled for two (2) minutes.
SIGNATURE EDITION AIRMASSEUR®
The Jason Signature Edition AirMasseur®bath includes a
variable-speed,1-HPairblowerwithheater,automaticpurge
cycle; and three (3) massage modes: Continuous, Wave, or
Pulse;Chromatherapymoodlight,AutomaticOzoneSystem
thatwillbeoperatedanytimetheblowerispowered;adigital
controlwithLCDdisplaywindow;lowwaterandtemperature
sensors; and a 20-minute timer.
Signature Touchpad
Amaincontroltouchpadmountedonthebathdeckfeaturesa
LCDreadoutwhichalternatelyindicatesthewatertemperature
(+/-5°F)andtimeremaining.TheSignatureEditiontouchpad
allows the bather to control the blower, pump, LED mood
light and optional jetted neck pillow. A built in timer shuts
the pump and blower off 20 minutes after being activated.
Signature Automatic Purge
Twenty (20) minutes after the control has shut off the blower
will start again for a two minute purge cycle that dries the air
channel. Note that the LCD display will read “PURGE” and
begin to countdown the 10 or 20 minute pause before the
purge cycle begins. The readout will display “PURGE ON”
duringthepurge cycle.Anytimeduringthepausebeforethe
purgecyclebegins,pressingandholdingtheBlowerSpeeds
icon will reduce the pause from 20 minutes to 10 minutes.
During the two-minute purge, pressing the “Blower On/Off”
icon will stop the purge.
Signature Daily Purge
The daily purge can be activated through the customized
settings of the Signature Edition touchpad. When activated,
the daily purge will start the blower for two-minutes at the
same time every day to dry the air channel. See ‘Operating
the Signature Edition AirMasseur Touchpad’ section for
details on activating this setting.
Signature Remote Control
Inadditionto themaincontrol touchpad installed on thebath
deck,afloating,waterproofUniversalRemoteControlispro-
videdwithallSignatureEditionAirMasseur®baths.Thisremote
controlprovidesthesamecontrolfunctionsasthebath’smain
control console,plus the bather may remotely operate a TV,
DVD,VCR,CD,etc.RefertotheInstructionManualprovided
with the remote control for detailed instructions.
Blower
The blower generates warm air and pushes it through the
air jets. Blowers provided on Jason AirMasseur®baths are
factory tested when assembled and again retested after
installation on the bath.
Filling And Draining
Close the drain and fill the bath with water to at least 10
inches(25cm)belowbathdeck.Theinlettemperatureshould
not exceed 40°C (104°F). When bath is in use, turn the unit
Off before draining the water. The bath unit and its plumb-
ing are designed to drain after each use whether used as
a hydrotherapy bath, soaking bath, or just taking a shower.

Jason International, Inc. • 501.771.4477 Page 19 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
Figure 21
O
AirMasseur®On/Off
Mode Blower Speeds
Option
®
STANDARD EDITION AIRMASSEUR®TOUCHPAD
Blower Speeds Icon
The Blower Speeds icon is used to increase or decrease
the blower speed once the blower is On.
• Press and hold the icon to decrease the blower
speed until the desired intensity is reached, then
release.
• Press and hold the icon again to increase the blower
speed until the desired intensity is reached.
The blower will return to its highest speed on any mode
change.
Option
The Option icon is used to operate an optional LED light
(if installed).
• Press the icon for less than two (2) seconds to turn
the lights Off or On.
• Hold the icon for more than two (2) seconds to
change modes.
This function has a two (2) hour timer and remembers the
last mode.
OPERATING INSTRUCTIONS, FEATURES, AND CONTROLS (cont.)
OPERATING INSTRUCTIONS
AirMasseur®On/Off Icon
The AirMasseur®icon is used to activate the blower and
the 20-minute timer.
• Pressing the Icon once starts the blower in the Con-
stant high speed mode.
• Pressing the icon again will turn the blower off.
Note: The blower will always turn on in high speed.
Mode Icon
The Mode icon is used to move the blower from Constant
mode to the Wave or Pulse modes.
• Press and release the icon once to change the
blower to the Wave mode, indicated by a slow flash-
ing light.
• Pressing the icon again will change the blower to
Pulse mode. This is indicated by a rapid light flash.
• Pressing the icon a third time moves the blower back
to Constant mode.

Jason International, Inc. • 501.771.4477 Page 20 of 26 Customer Service : 800.255.5766
Copyright © 2014 Jason International,Inc.
Figure 22
SIGNATURE EDITION AIRMASSEUR®TOUCHPAD
Customized Settings
The12 characterLCD displaycanbecustomizedbypressing
the AirMasseur®and Blower Speeds icons simultaneously
for five (5) seconds, while the system is Off. Note: The Blower
Speeds icon will not be illuminated during this process. Use
the above figure to locate the icon. A menu (see below) will
be displayed to choose the following: Purge 24, (starts the
blowerevery24hoursfortwo(2)minutesatthetimethepurge
wasset);ProductTestDiagnostics (seebelow);Temperature
(Fahrenheit or Celsius); and Language (English or Spanish).
Menu Instructions
Use the AirMasseur®icon to scroll through the different menu
items. Use the Blower Speeds icon to change an option. For
example, press and release the AirMasseur®icon to change
from Purge 24 to Product Test; press and release again to
arrive at the Temperature option. Then press and release the
Blower Speeds icon to change the temperature display from
F (Fahrenheit) to C (Celsius).
Product Test Diagnostics
AfterselectingtheProductTestoptionfromthemenu,theunit
will perform a series of tests to confirm correct installation of
components.Thetestwillbeginbydisplayingtheconfiguration
number, followed by the software revision number. Next, the
displaywilltesttheTemperatureandLowWater Levelsensor
(ITW-209). Next, each of the six (6) icons will begin to light.
Presstheilluminatedicontoproceedtothenexticon.Afterthe
icon test, the blower will start for two (2) seconds on the High
setting. Lastly, the LED Light unit will be tested. If you receive
an error on any of the tests, confirm proper installation of the
component to the correct control box. (See the CONTROL
BOX CONNECTIONS section).
Remote Control
The Signature Edition control system includes a waterproof
floatingUniversalRemoteControl.Itcontrolsallbathfunctions
plus a TV, DVD, CD, etc. which can be heard through the
optional Sound Immersion Transducers (optional).
AirMasseur® On/Off, Mode
Blower Speeds
LED Light
IR for Remote
OPERATING INSTRUCTIONS, FEATURES, AND CONTROLS (cont.)
OPERATING INSTRUCTIONS
AirMasseur®On/Off and Mode Icon
Tocontroltheoperationoftheblower,simplypressandrelease
to change the setting to Constant, Wave, Pulse or Off. A 20
minute decreasing timer will be initiated when the blower
motor starts. Press and hold the Blower icon to cycle though
blower modes. The Blower icon should remain lit as long as
the bath is connected to a power supply. The LCD will display
“Const Air” and blower speed, “Wave Air” and blower speed,
or “Pulse Air” and blower speed, while the key is pressed.
The time remaining on the purge cycle is displayed after the
bath has drained. “Purge Stop” is displayed while the key is
pressed during the purge cycle. This action will terminate the
purge cycle. The mode settings will be remembered on the
next startup.
Blower Speeds Icon
Hold the key in Constant mode to go from High to Low then
release and holdagain to go fromLow to High.Hold the key in
WaveandPulsemodetogofromHightoMediumandMedium
to High. The system remembers the last speed setting on the
next startup. The Blower Speeds icon will light up when the
blower is running. The LED displays the blower speed from
“10”(Low)or“55”(Med)to“99”(High)whilethekeyispressed.
You can reduce the auto purge idle time from 20 minutes to
10 minutes, by pressing and holding the key for more than
5-seconds during the purge idle period.
LED Light Icon
Holdtheiconforlessthantwo(2)secondstoturnthelightsOff
or On. Hold the icon for more than two (2) seconds to change
modes. The Light icon should remain lit as long as the bath
is connected to a power supply. This function has a two (2)
hour timer and remembers the last mode. The LCD displays
“Light On” or “Light Off” while the icon is pressed for less than
two (2) seconds. “Light Cycle” is displayed if pressed for more
than two (2) seconds.