JCM Technologies PAD User manual

User Manual
PAD

Table of contents
Important safety instructions 3
Use of the equipment 3
Description 3
Technical characteristics 3
Assembly 4
Wiring 4
Connection to the HDOOREVO 5
Configuration 6
Wiegand34 selection 6
Change PIN length 6
Change master code 6
Restart the factory master code 6
Options Menu 7
Regulatory Data 8
UKCA Declaration of conformity 8
EU Declaration of conformity 8
jcmtechnologies
2

Important safety instructions
•Do not install the device in a place exposed to sunlight without a protective visor.
•Do not install the device or its wiring near a source of strong electromagnetic fields, such as a radio transmission antenna.
•Do not place the device either near, or on top of heating equipment.
•When cleaning, do not use water or other liquid cleaning products, wipe with a soft cloth or towel. Do not allow children to
touch the device without proper supervision.
Use of the equipment
This equipment is designed for applications with an automated garage door. It is not guaranteed for the direct activation of
other devices other than those specified.
The manufacturer reserves the right to change the specifications of the equipment without prior notice.
Description
PAD is a multiprotocol Wiegand/clock and amp, Data/Codix keyboard, with a configurable PIN length.
The integrity breach (tamper) switch will activate the alarm system if you try to open or remove the unit from the wall.
By default, PAD is set with the Wiegand 26 protocol with a 4-digit PIN.
Technical characteristics
Interface Wiegand de 26, 30, 34, 37, 40, 42 ó 58 bits, Clock-
&Data or Codix
Protocol programming By keypad
Maximum cable length 50m
Connection Cable, 0.45m
Green and red LED Externally controlled
Orange LED Key and menu touch
Bell ON/OFF Yes
Backlight ON/OFF Yes
Manual control Yes
Consumption 60mA
Watertightness IP65
Power supply 9-14VDC
Operating temperature -20°C to +50°C
Dimensions (mm) 92 x 51 x 25
Housing Moulded aluminium
jcmtechnologies
3

Assembly
1- Identify a suitable location on a wall or flat sur-
face.
2- Stick on the mounting template and drill the holes
according to the diagram.
3- Insert the three 5mm screw plugs into the holes. 4- Pass the cables through the back plate.
5- Fasten the back plate firmly to the wall with the
three 30mm screws.
6- Connect the cables and place the housing onto
the back plate, guiding it from the top down.
7- Secure the housing to the back plate with the three 6mm safety screws using the screwdriver provided.
Wiring
jcmtechnologies
4

12V DC 9-14V CC
GND Ground
Tamper Tamper Switch
Tamper Tamper Switch
LED Green - Green LED
LED Red - Red LED
D1 Data 1
D0 Data 0
Connection to the HDOOREVO
jcmtechnologies
5

Configuration
By default, PAD is set with the Wiegand 26 protocol with a 4-digit PIN.
Default master code: 000000
Wiegand34 selection
•Hold the "B" key down until you hear 3 beeps.
•Master code (by default: 000000) →Orange LED activated.
•Press 6.
•Press 2.
•Press A →Orange LED deactivated.
Change PIN length
Example 8-digit PIN:
•Hold the "B" key down until you hear 3 beeps.
•Master code (by default: 000000) →Orange LED activated.
•Press 4.
•Press 8.
•Press A →Orange LED deactivated.
Notes:
•Option 4-6: 6-digit PIN (recommended for WG26).
•Option 4-9: 9-digit PIN (recommended for WG34).
•Option 4-0: PIN for any length (not recommended).
•If you want to work without a limitation on duration, consider these restrictions (Warning: with these modes, higher val-
ues will cause double codes):
•WG26 →maximum value = 16,777,215
•WG34 →maximum value = 4.294,967,295
•Caution: values higher than the maximum value will lead to repeated codes when the device decodes the PIN.
•In this mode, you must press "A" to send the PIN you have entered.
Change master code
•Hold the "B" key down until you hear 3 beeps.
•Master code (by default: 000000) →Orange LED activated.
•Specify the new master code (6 digits).
•Press A →Orange LED deactivated.
Restart the factory master code
•Disconnect from power source.
•Hold the "A" key down and reconnect to power source.
•Hold the "A" key down for at least 2 seconds.
•You will hear 3 beeps.
jcmtechnologies
6

Options Menu
jcmtechnologies
7

Regulatory Data
UKCA Declaration of conformity
JCM TECHNOLOGIES, SAU hereby declares that the product PAD complies with the relevant fundamental requirements of
the Electromagnetic Compatibility Regulations 2016 whenever its usage is foreseen; and with the RoHS Regulations 2012.
EU Declaration of conformity
JCM TECHNOLOGIES, SAU hereby declares that the product PAD complies with the relevant fundamental requirements of
the Directives 2014/30/EU on electromagnetic compatibility whenever its usage is foreseen; and with the 2011/65/EU RoHS
Directive.
See website https://www.jcm-tech.com/declarations/
JCM TECHNOLOGIES, SAU
C/ COSTA D'EN PARATGE, 6B
08500 VIC (BARCELONA)
SPAIN
jcmtechnologies
8
UM_3201059_PAD_EN_Rev02