Jenn-Air CCE3451 User manual

Induction _JENN-AIR 1
RadiantCooktop ,_ _E__ou_sT_E_._o_•N_0_.,,50_i
L 1
p.-
INSTALLATION
INSTRUCTIONS
Model CCE3451
IMPORTANT:SAVEFOR LOCAL ELECTRICALINSPECTOR'SUSE
See suggestions 1-4 on page 2.
- DIMENSIONS
' • inches cm
A28 7/8 "k 1/16 73.3
B 20 1/4=l:'/16 51.4
C 2 1/8rain. 5.4
D 4 1/2rain.clear* 11.4
E 29 W1676.0
F 21 V254.6
G4 3/16 10.6
*installerInstructions for dimension "D".
Ifunit is mountedover aW130 or W131 wall
oven the minimumclearanceis 61/_" (15,9cm)
minimum.
UNITS PROVIDED WITH: 1/2"(1.3 cm) FLEXIBLE CABLE, 45" (114.3 cm) LONG WITH,6" (15.2
cm) WIRE LEADSAT END, FURNISHED AND INSTALLED BY MANUFACTURER (CONNECT TO
240/120 VOLT ELECTRICAL SERVICE). CABLE IS LOCATED AT THE CENTER REAR OF THE
COOKTOP.
INSTRUCTIONS TO INSTALLER
• E!ectric Hook Up -Theunit should beproperly circuit protected and wired according to local
electrical codes. See electrical wiring information on back. Unit power requirements are located
on the data plate.
•UNIT MAY BE INSTALLED INCOMBUSTIBLE COUNTERTOP AND ADJACENT TO(0"
FROM) COMBUSTIBLE WALLS.
8101P287-60
(07-97-00)

InstallingCabinetryOver Your Cooktop ElectricalWiringInformation
Framegroundedto neutralthrough a link.Thiscooktopnot
A = 30" (76.2 cm) Minimum clearance between for useinmobilehomesor inareaswhere localcodes donot
thetop of the cooking platformand the bottom permitgroundingthrough neutral.
of an unprotected wood or metal cabinet.
A = 24" (60.96cm) Minimumclearance when bot-
tom of woodor metal cabinet is protected by Proper Electrical Supply
not lessthan 1/4"(0.635 cm). FLAME RE-
TARDANTmillboardcoveredwithnotlessthan
no. 28 MSGsheetsteel, 0.015"(0.038 cm)Yourmustprovideanadequateelectricalsupplysystemas
stainlesssteel, 0.024"(0.061cm) aluminumor requiredfor yourcooktop. All wireconnectionsmustbein
copper, accordancewithlocalcodesandproperlyinsulated.Check
withlocalutilityforgovemingelectricalcodesandordinances.
_.r Intheabsenceoflocalelectricalcodes,theNationalElectrical
Dottedindicatetines4111 Code,NFPA No.70, governing electricrange installations
rangehood .II must be followed. A copy of the National ElectricalCode,
construction_ _ " NFPANo.70, canbe obtainedbywriting to:
-= /
"_ \/--/-- National Fire Protection Association
J_" BatterymarchPark
Quincy,Massachusetts02269
L_ ----- Athree-wire,single phase, A.C. 120/240 volt 60 cycle electd-
cal system (properly circuitprotected to meet LocalCodes of
*To eliminatethe nsk of burns orfire by reaching over
heated surface units, cabinet storage space locatedNFPA No. 70) must be provided. Unit must be properly
abovethesurfaceunitsshouldbeavoided.If cabinet groundedin accordancewith local wiring code.the chart
storageis to be provided,the riskcanbe reducedby below recommendsthe minimumcircuit protector and wire
installinga rangehoodthatprojectshorizontallya mini- size ifthe applianceisthe onlyuniton the circuit. If smaller
mumof 5 inchesbeyondthe bottomof thecabinets, sizesofwireare used,theunitefficiencywillbereducedand
afire hazardmaybecreated. Itisadvisablethattheelectrical
Important Installation Suggestions wiringand hookup beaccomplishedby a competent electri-
cian.
1. Chamfer all exposed edges of decorative laminate to RECOMMENDEDMINIMUM
preventdamagefrom chipping. K.W,RATING CIRCUITPROTECllONWIRESEE
2. Radiuscornersofcutoutandfiletoinsuresmoothedges ONSERIALPLATE INAMPERS (AWG)
andpreventcornercracking. 0 - 4.920 12
5.0- 6.9 30 10
3. Roughedges,insidecomerswhichhavenotbeenrounded 7.0- 9.9 40 8
andforced fitscan contributetocrackingof thecounter 10.0- 11.9 50 8
top laminate.12.0- 14.9 60 6
4. Countertopmust besupportedwithin3" of cutout.

Notice to Installer Installation of Appliance
Followaccompanyinginstructioncarefully.1. Removethe cooktop fromthe cartonand place
,_ it upsidedown over two soft padsmaking sure
, +
r_ +_, controlknobs do not interferewithany surface.
2. Peel off the backing paper from one of the
piecesof foam tape providedwith the unitand
stickthe adhesive backedtape to the glassas
close as possbleto the burner box alongthe
frontedge of the cooktop. Repeatthe process
with the second pieceof foam tape along the
rear edge ofthe cooktop.
Preparation of Countertop Glass I Foam Tape
Thecutoutinthecountertopintowhichtheappliance I
is to be installedshould be preparedaccording to
the cutout dimensions given on page 1 of these
instructions.
Bottom View
ii_ .............. _ +................... .Burner///_ ...... ,,,.,_-
Box IFoam Tape
Burner
Box
Foam
I Tape/
l_ (Placeas closeas
I_possibleto Buner
IL _Boxalong frontand
41-, _ _ , rearedges only,)
3. Provide cutout in countertop as required per
page 1.
4. Placeunit in the cutout.
5. Makeelectricalwireconnectionto unit. Consult
local codesfor proper power hook-up,
6.Testto insurecontrolknobsoperateallelements
properly.

240EdwardsStreet,SE
Cleveland.Tennessee37311
TeE423-472-33S3
Fax:423_78-57_0
30" GLASS COOKTOP WITH SOLID ELEMENTS
INSTRUCTIONS TO APPLY FOAM TAPE
1. Remove the glasstop unit from the carton and place it upside down over two soft pads making sure control
knobs do not interfere with any surface.
2. Peeloff the backing paper from thefoamgasketprovided withthe unitandstick the adhesive backed tape
to the glassalong its edge. Installcooktop.
FIGURE3
../_OETAIL
_lflr,lu_
FI6UAE 4/--.../..
I21"30"6"WIRE LEADS
2 $/4"
DEPTH I/2"FL[XiBLE CASLE 48"LONG
FL_NISHEO ANOINSTALLED BY
MANL_ACTURER(CONNECT TO
240/120 VOLT ELECTRICAL SERVICE]
Of UNIT
2l/8'
MIN