JL Marine Power-Pole Advanced Foot Switch User manual

Conditions of warranty
An Advanced Foot Switch manufactured by JL Marine Systems Inc., is warranted against defects in
material and workmanship to the original owner according to the following stipulations.
1. Advanced Foot Switch warranty is activated on the date of purchase by JL Marine Systems, Inc.
You may also register your Advanced Foot Switch on our web site or send in the registration
card. Please retain your sales receipt as proof of purchase.
2. Install Genuine Power-Pole Merchandise ONLY. This warranty is void if any non authorized parts
are used or installed.
3. This warranty is void if the Power-Pole Advanced Foot Switch is used commercially structurally
altered or subject to stress beyond the physical limits of the manufactured material. This
Warranty is void if the Advanced Foot Switch is exposed to excessive water or submersion.
1. Parts which prove defective within (90) days from the date of purchase, JL Marine Systems,
Inc. will pay for the replacement product shipping and handling fees to
and from the JL Marine Systems, Inc. manufacturing plant or some other place which
JL Marine Systems, Inc. might designate. Warranty shipping procedures only apply
in the continental USA.
2. Parts which prove defective after (90) days but before (24) months from the date of
purchase will also be repaired or replaced free of charge, but there may be a shipping
charge to JL Marine Systems, Inc. manufacturing plant or some other place which
JL Marine Systems, Inc. might designate. Warranty shipping procedures only apply
in the continental USA.
THE WARRANTY CONTAINED HEREIN IS THE EXCLUSIVE WARRANTY MADE BY JL Marine
Systems, Inc. AND THERE ARE NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING
A WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR OF MERCHANTABILITY MADE
WITH RESPECT TO SUCH ANCHORS. JL Marine Systems, Inc. IS NOT LIABLE FOR ANY INJURY
OR MISHAPS SUSTAINED IN THE USE OF THIS PRODUCT. THE USER OF THIS PRODUCT
ACKNOWLEDGES ASSUMED RISKS AND WAIVES ANY AND ALL CLAIMS AGAINST JL Marine
Systems, Inc. AND ANY OF IT’S AGENTS.
This warranty applies under conditions of normal use. The warranty does not cover:
1) defects caused by improper assembly or disassembly; 2) defects occurring after purchase due
to product modification, intentional damage, accident, misuse, abuse, negligence or exposure to
corrosive elements; 3) cosmetic damage and 4) labor or assembly costs.
Except as provided herein, JL Marine Systems, Inc. makes no express warranties, and any implied
warranty, including without limitation any implied warranty of merchantability or fitness for a particular
purpose, is limited in its duration to the duration of the written limited warranty set forth herein.
Except as provided herein, JL Marine Systems, Inc. shall have no liability or responsibility to the
purchaser or any other person or entity with respect to any liability, loss or damage caused or
alleged to be caused directly or indirectly by use of the product, including, but not limited to, any
incidental or consequential damages. Some states do not allow limitation on how long an implied
warranty lasts or the exclusion of limitation of incidental or consequential damages, so the above
limitation and exclusion may not apply to you. This warranty gives you specific legal rights. You may
also have other rights which vary from state to state.
Two (2) year warranty
PLACE
POST CARD
POSTAGE HERE
Post office will not
deliver without
proper postage.
9208 Palm River Road
Suite 303
Tampa, FL 33619
___________________________________
___________________________________
___________________________________
Operating Instructions
Using Speed Control
1. The foot switch has three speed settings (slow, medium, & fast).
Depressing and releasing the “speed” button on the foot switch will
toggle through the three settings. (See Figure 1)
2. The LED on the foot switch will flash at a speed corresponding to either a
slow, medium, or fast setting.
Dual Power-Pole Operation
1. With dual Power-Pole shallow water anchors installed, the foot switch can
also be used to toggle between independent or simultaneous control of
the anchors. Depressing and releasing the “directional” button on the
foot switch will toggle through the three settings (port side only, starboard
side only, or simultaneous control).
(See Figure 2, 3, 4 and 5)
2. The LED will flash either port side only, starboard side only, or on both
sides to indicate the current control settings
3. To raise or lower the Power-Pole shallow water anchor, press and hold
either the “up” or “down” button on the foot switch. The anchor will only
continue to move so long as you keep the button depressed.
4. Auto Mode: Double tapping (depressing and releasing 2 times within 1
second) either the “up” or the “down” button on the foot switch will cause
the anchor to retract or deploy automatically. The Power-Pole anchor will
continue to move in said direction until it either retracts completely or
senses the bottom.
Sleep Mode: Press both buttons for 3 seconds, LED lights will flash indicating
the Foot Switch is now in Sleep Mode. To reactivate, press both buttons
again for 3 seconds until LED lights flash.
Figure 1
Figure 2
Figure 4
Figure 3
Figure 5

Installation Instructions
Changing the Battery
Programming Instructions
Congratulations on your purchase of an Advanced Foot Switch featuring
state-of-the-art C-Monster Control System technology.
Installation
Step 1 Locate a suitable area with a flat surface to mount the foot switch.
Step 2 Remove the foot switch from its rubber pad, and hold it in the desired
location. Use a fine point marker to inscribe the intended mounting
screw locations. (See Figure 1)
WARNING – Before drilling pilot holes for the foot switch mounting screws,
inspect the area beneath the mounting surface in order to ensure
that the drill bit will not cause any damage.
Step 3 Using the 7/64” drill bit, carefully drill holes in the previously
inscribed location.
Step 4 Place the foot switch back into its rubber pad, and fasten both the
switch and pad to the vessel using a #2 Phillips-head screwdriver
and the (3) #6 x 3/4” pan head screws. (See Figure 2)
Changing the Battery
Step 1 Remove the (3) #6 x 3/4” pan head screws with a #2 Phillips-head
screwdriver, and remove the foot switch and its rubber base from
the vessel’s surface.
Step 2 Take the foot switch and its base
to a dry location, and separate the
foot switch and rubber base.
Step 3 Thoroughly dry the foot switch and
then remove the (7) screws on its
underside with a #1 Phillips-head
screwdriver. (See Figure 1)
Step 4 With the screws removed, life the cover off of the switch, and
carefully remove the circuit board.
Step 5 Replace the battery with any CR2032 3V Lithium Coin Battery.
Step 6 Inspect the inside of the foot switch case thoroughly for signs of
moisture as well as damage to the rubber seals. If the rubber seals
appear to be damaged, or of a substantial amount of moisture is
found, please contact a member of our technical support staff.
[[phone] option 2]
NOTE: If needed, a hair dryer may be used to dry residual moisture in
the foot switch case.
Step 7 Assemble and install the foot switch in the reverse order.
Programming
Step 1 Locate the “program” button on the top of the pump unit, depress
and hold it for 3 seconds until the LED steadily illuminates green in
color. The pump unit is now ready to be paired with a foot switch.
(See Figure 1)
NOTE: When dual Power-Pole shallow water anchors are installed,
this procedure should be performed on BOTH pump units.
Step 2 Next, depress and release either the “up” or the “down” button on
the foot switch 1 time. The green LED on the pump unit will initially
turn off, and then it will return to flashing once per second, this will
indicate that the pairing has been completed. (See Figure 2)
Step 3 The foot switch is now paired to the pump unit. Test its functionality
with both the “up” and the “down” buttons to ensure that the pairing
procedure was completed successfully.
Advanced Foot Switch
Featuring Technology
IMPORTANT!
REGISTER YOUR NEW ADVANCED FOOT SWITCH
To validate your warranty, register your new product online at www.power-pole.com
or ll out and submit this registration card.
Name ______________________________________________________________________
Address _____________________________________________________________________
City _____________________________________ State _________ Zip ______________
Email address ________________________________________________________________
Date of purchase __________________________________________ Age ______________
Place of purchase ______________________________________________________________
Type of boat ___________________________________________ Length ______________
I have read and understand the warranty of this product.
Signature ____________________________________________________________________
Figure 1 Figure 2
Figure 1
Figure 1 Figure 2