Johnson Controls TEC-6-PIR User manual

Passive Infrared (PIR) Accessory Covers Installation Instructions 1
Applications
The Passive Infrared (PIR) Accessory Covers with
embedded PIR motion detectors are specifically
designed to work with compatible Johnson Controls®
TEC and T60x Series Equipment Controllers. These
accessory covers are designed to retrofit previously
installed controllers, or to serve as replacement covers.
When equipped with a PIR Accessory Cover, the
controller provides advanced active occupancy logic,
which automatically switches occupancy levels from
Occupied to Unoccupied or Standby as required by the
presence of local activity. This added occupancy
sensing capability provides energy savings during
occupied hours without sacrificing occupant comfort.
A PIR Accessory Cover is suited for the following
applications:
• lodging Fan Coil Unit (FCU) applications
• TEC Zoning Control System zones
• conference rooms
• classroom units
• any commercial offices that have random
occupancy schedules during occupied hours, as
dictated by the function of the tenant
• any controlled piece of HVAC equipment that may
yield energy savings with the introduction of a new
automatic standby level of occupancy
North American Emissions Compliance
United States
Canada
This equipment has been tested and found to
comply with the limits for a Class A digital device
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference when this equipment is
operated in a commercial environment. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area
may cause harmful interference, in which case the
users will be required to correct the interference at
their own expense.
This Class (A) digital apparatus meets all the
requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la Classe (A) respecte
toutes les exigences du Règlement sur le matériel
brouilleur du Canada.
Passive Infrared (PIR) Accessory Covers
Installation Instructions
TEC-3-PIR, TEC-6-PIR, TEC-6H-PIR, and TEC-7-PIR Part No. 24-9890-870, Rev. E
Issued March 2016
24- 9890- 870, Rev. E

Passive Infrared (PIR) Accessory Covers Installation Instructions2
Installation
To install a PIR accessory cover:
1. Remove the security screw on the bottom of the
existing controller cover.
2. Open the existing cover by pulling upward on the
bottom edge of the controller cover, and remove
the cover.
3. Insert the polarized connector on the bottom left
corner of the PIR accessory cover into the
PIR connector located on the controller base
(Figure 1).
4. Hinge the PIR accessory cover into position
(Figure 1).
5. Snap the PIR accessory cover into place and
reinstall the security screw.
6. Use the configuration menu to make the
appropriate parameter settings related to the
specific application, as identified in the controller
installation instructions. See the Configuration
Parameters section for more details.
The PIR motion detector may take up to 60 seconds
after the initial warm-up period to detect movement
consistent with the detection pattern. Blinking
Light-Emitting Diodes (LEDs) located on
PIR accessory cover beneath the motion detector aid
in commissioning. The LEDs blink while an occupant
is in the field of detection pattern for a period of
30 minutes after powerup.
Configuration Parameters
When installing a PIR accessory cover on a controller,
set the following configuration parameters to
appropriate values: PIR Func, BI1, St-By HT, and St-By
CL. Each PIR accessory cover requires additional
parameters to configure according to the compatible
controller model (Table 1).
For further information on configuration parameter
settings, refer to the appropriate installation
instructions for the specific controller model.
For application information details on the PIR
sequence of operation, refer to the documentation
listed in Table 2.
Mounting
Location Considerations
The typical detection pattern for the PIR sensor is
shown in Figure 2. Consider this pattern when
positioning the controller.
!
CAUTION: Risk of Electric Shock.
Disconnect the power supply before
making electrical connections to avoid
electric shock.
MISE EN GARDE : Risque de décharge
électrique.
Débrancher l'alimentation avant de
réaliser tout raccordement électrique afin
d'éviter tout risque de décharge
électrique.
!
CAUTION: Risk of Property Damage.
Do not apply power to the system before
checking all wiring connections. Short
circuited or improperly connected wires
may result in permanent damage to the
equipment.
MISE EN GARDE : Risque de dégâts
matériels.
Ne pas mettre le système sous tension
avant d'avoir vérifié tous les raccords de
câblage. Des fils formant un court-circuit
ou connectés de façon incorrecte
risquent d'endommager
irrémédiablement l'équipement.
IMPORTANT: Make all wiring connections in
accordance with the National Electrical Code and
local regulations. Use proper Electrostatic Discharge
(ESD) precautions during installation and servicing
to avoid damaging the electronic circuits.
Figure 1: Wiring to the PIR Connector on the
Controller Base, and Attaching the
PIR Accessory Cover
FIG:cvr_rmvl

Passive Infrared (PIR) Accessory Covers Installation Instructions 3
Figure 2: Typical Detection Pattern
PIR TRIGGER ZONE
45°
FLOOR
20 ft
61 m
0°
60°
60°
30°
FIG:pir_dtctn_pttrns
30°
5-1/2 ft
166 cm
5-1/2 ft
166 cm
Table 1: PIR Accessory Cover Code Numbers and Configuration Parameter Settings
Code Number Compatible Controller Series Configuration Parameter Settings
TEC-3-PIR T600xxx-4, T600xxx-4+PIR, T606MSx-4,
T606MSx-4+PIR, TEC2x0x-4,
TEC2x0x-4+PIR, TEC2613-4, and
TEC2613-4+PIR
The PIR accessory cover is auto-detected. Set the Occupied
Setpoints, Unoccupied Setpoints, and Unoccupied Timer
(Unocc TM) to the desired comfort levels.
TEC-6-PIR TEC20x6-2, TEC2xx6-4, and TEC2x45-4 The PIR accessory cover is auto-detected. Set the Occupied
Setpoints, Standby Setpoints, Unoccupied Setpoints,
Unoccupied Timer (Unocc TM), and Standby Timer (St-By
TM) to the desired comfort levels.
TEC-6H-PIR T60xDFH-4, T60xDFH-4+PIR,
TEC20x6H-2, TEC2xx6H-4, and
TEC2xx6H-4+PIR
TEC-7-PIR TEC20x7-2, TEC2xx7-4, and
TEC26x7-4+PIR
TEC2647Z-2, TEC2647Z-2+PIR,
TEC2647Z-3, and TEC2647Z-3+PIR
Set the PIR Function (PIR Func) parameter to enable PIR.
Set the Unoccupied Setpoints and Standby Setpoints to the
desired comfort levels.
Table 2: PIR Application Documents
Code Number Document Title Document
Number
T60xDFH-4 and T60xDFH-4+PIR T60xDFH-4 and T60xDFH-4+PIR Series Thermostat Controllers with
Dehumidification and Occupancy Sensing Capability Application Note LIT-12011569
TEC2x45-4, TEC2xx6-4,
TEC2xx6H-4, TEC2xx6H-4+PIR,
TEC2xx7-4, TEC26x7-4+PIR
TEC2x45-4, TEC2xx6(H)-4, TEC2xx6H-4+PIR, TEC2xx7-4, and
TEC26x7-4+PIR Series Thermostat Controllers Application Note LIT-12011594

Published in U.S.A. www.johnsoncontrols.com
Passive Infrared (PIR) Accessory Covers Installation Instructions4
Metasys® and Johnson Controls® are registered trademarks of Johnson Controls, Inc.
All other marks herein are the marks of their respective owners. © 2016 Johnson Controls, Inc.
Building Efficiency
507 E. Michigan Street, Milwaukee, WI 53202
Repair Information
If the PIR accessory cover fails to operate within its
specifications, replace the unit. For a replacement
cover, contact the nearest Johnson Controls
representative.
Technical Specifications
PIR Accessory Covers
Power Requirements 5 VDC Maximum; Current Draw of 7 mA Supplied by the
Johnson Controls TEC or T60x Series Equipment Controller
Ambient Operating Limits Temperature 32 to 122°F (0 to 50°C)
Humidity 0 to 95% RH, Noncondensing;
85°F (29°C) Maximum Dew Point
Ambient Storage Limits Temperature -22 to 122°F (-30 to 50°C)
Humidity 0 to 95% RH, Noncondensing
Motion Detector Local Passive Infrared Sensor
Dimensions
(Including Controller) 4-15/16 in. H x 3-3/8 in. W x 1-13/32 in. D (125 mm H x 86 mm W x 36 mm D)
Compliance United States UL Listed, File E27734, CCN XAPX
Under UL 873, Temperature Indicating and Regulating Equipment
FCC Compliant to CFR 47, Part 15, Subpart B, Class A
Canada UL Listed, File E27734, CCN XAPX7
Under CAN/CSA C22.2 No. 24, Temperature Indicating and Regulating
Equipment
Industry Canada, ICES-003
Europe CE Mark – Johnson Controls, Inc., declares that this product is in
compliance with the essential requirements and other relevant provisions
of the EMC Directive and the RTTE Directive.
Australia and
New Zealand RCM Mark, AS/NZS CISPR 22 Compliant
Supplier Code Number N10696
Shipping Weight 0.1 lb (0.05 kg)
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be liable for damages resulting from misapplication or
misuse of its products.
European Single Point of Contact: NA/SA Single Point of Contact: APAC Single Point of Contact:
JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY
JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA
JOHNSON CONTROLS
C/O CONTROLS PRODUCT MANAGEMENT
NO. 22 BLOCK D NEW DISTRICT
WUXI JIANGSU PROVINCE 214142
CHINA