Johnson Controls A350E Manual

FANs 930, 930.5, 125, 121
Product/Technical Bulletin A350E
Issue Date 0899
© 1999 Johnson Controls, Inc. 1
Part No. 24-7664-400, Rev. B www.johnsoncontrols.com
Code No. LIT-930015
System 350


A350E Electronic Cooling Control
The A350E is an on/off, electronic, cooling-only control
with Single-Pole, Double-Throw (SPDT) relay output
and Light-Emitting Diode (LED) relay status indication.
A cooling-only control, the A350E has two features that
differentiate it from the A350A/B Series Electronic
Temperature Controls: a selectable minimum setpoint
and short/open sensor detection. The A350E also has
an adjustable differential and an interchangeable
temperature sensor.
As are all System 350™ products, the A350E is
housed in a NEMA 1, high-impact plastic enclosure.
The modular design provides easy, plug-together
connections for quick installation and future
expandability.
Figure 1: A350E Electronic Cooling
Control
Features and Benefits
❑Modular Design Enables stage, display, and power modules to
be purchased and installed as necessary
❑Minimum Setpoint
Selections
Allows the selection of a minimum setpoint at
which the equipment can be set to control
❑Reacts to Short or Open
Sensor Condition
Deenergizes output relay if the sensor or
sensor wiring fail
❑Wide Adjustable Differential
of 1 to 30F° (0.6 to 16.7C°)
Enables the user to match equipment cycle
rate and/or sequencing for a given application
❑Plug-together Connectors
and 35 mm DIN Rail
Mounting
Eliminates wiring between modules and
reduces installation costs
❑One Dual-scale Model
Covers a Temperature
Range of 10 to 65°F
(-12 to 18°C)
Supports the majority of Fahrenheit and
Celsius cooling applications
❑Interchangeable
Temperature Sensors
Increases versatility and serviceability

2 System 350 A350E Electronic Cooling Control Product/Technical Bulletin
Application
The A350E Cooling Control can be used as a
standalone device or in conjunction with other
System 350 plug-together accessory modules to
control a wide variety of single or multiple-stage
equipment. Typical applications include:
•frozen/refrigerated food cases
•cooling tower control
•beverage/milk coolers
•chiller staging
•space temperature control (cooling only)
A typical cooling control scheme includes the following:
•A350E Cooling Control
•One or more S350 Stage Modules
•D350 Digital Temperature Sensor/Setpoint Display
Module
•Y350R Power Module (or 24 VAC Class 2
transformer)
•A99B Temperature Sensor
Operation
The A350E Cooling Control operates on 24 VAC and
provides an SPDT relay output. A front-panel LED
lights to indicate when the relay is energized.
Adjustable features include:
•setpoint
•differential
•minimum setpoint
IMPORTANT: All System 350 controls are
designed for use only as
operating controls. Where an
operating control failure would
result in personal injury and/or
loss of property, it is the
responsibility of the installer to add
devices (safety, limit controls) that
protect against, or systems
(alarm, supervisory systems) that
warn of, control failure.
Setpoint Adjustment
Setpoint is defined as the temperature at which the
A350E’s relay will de-energize. Refer to Figure 3. Use
the Setpoint Dial on the front of the A350E to adjust
setpoint. See Figure 2.
Minimum Setpoint Jumper
Four possible settings are available: 20°F (-7°C),
30°F (-1°C), 40°F (4°C), and Off. Refer to Figure 2 and
use the jumper to select the desired minimum setpoint.
The minimum setpoint function overrides any knob-
selected setpoint that is lower than the minimum
setpoint. For example, if a minimum setpoint of 40°F is
selected and the dial is set at 32°F (0°C), then the
control setpoint will be 40°F (4°C). The external knob
will change the control setpoint only when it is adjusted
between 40 and 65°F (4 to 18°C).
When the minimum setpoint jumper is removed or the
Off position is selected, the setpoint can be adjusted
over the full range of 10 to 65°F (-12 to 18°C).
Setpoint
Dial
Module
Connector
Relay
LED Indicator
Minimum
Setpoint Jumper
OFF
N.C.
Relay
COM
Output
N.O.
Terminals
Relay
DIFF
(Differential
Potentiometer)
RelayRelay
24V
COM
COM
SEN
20 F (-7 C)°°30 F (-1 C)°°
40 F (4 C)°°
Figure 2: A350E Electronic Cooling Control
Board Layout and Terminal Locations

System 350 A350E Electronic Cooling Control Product/Technical Bulletin 3
Differential Adjustment
Differential is defined as the change in sensor
temperature between the energization and
de-energization of the relay. (See Figure 3.) The
differential can be adjusted between 1 and 30F°
(0.6 and 16.7C°). Adjustment is made using the differential
potentiometer, marked DIFF. (See Figure 2 for location.)
ON
OFF
(+)
(-)
Differential
ON = Energized
OFF = De-energized
Setpoint
Temperature
OFF
Differential
ON
OFFSET
Figure 3: Relationship Between Differential
Setpoint and Offset
Add-On Modules
The S350 Stage Modules, D350 Digital Temperature
Display Module, and Y350R Power Module connect
together and plug into a connector on the right side of
the A350E. The maximum number of add-on modules
is listed in Table 1.
Table 1: Maximum Number of S350 Stage
Modules per A350E
Power
Source
Number
of S350A
or S350C
Modules
Allowed
Number of
S350A or
S350C
Modules
(with
1 S350P)
Allowed
Number
of S350A
or S350C
Modules
(with
2 S350Ps)
Allowed
Y350R 96 4
External
Class 2
Transformer
98 7
S350A On/Off Stage Modules
S350A On/Off Stage Modules receive power, setpoint,
and sensor input from the A350E control. S350A Stage
Modules perform switching functions based upon the
A350E’s setpoint, sensor information, with the offset and
differential selected at the S350A. For more information
on these modules, refer to the System 350TM S350
Temperature, S351 Humidity, and S352 Pressure On/Off
Stage Modules Product/Technical Bulletin (LIT-930080).
S350C Slave Stage Modules
S350C Slave Stage Modules receive power and
sensor input from the A350E control. S350C Slave
Stage Modules perform switching functions based
upon the A350E’s sensor information, with the setpoint
and differential selected at the S350C. For more
information on these modules, refer to the
System 350TM S350C Temperature Slave Stage
Module Product/Technical Bulletin (LIT-930084).
S350P Proportional Stage Modules
S350P Proportional Stage Modules receive power,
setpoint, and sensor input from the A350E control. The
S350P responds with an analog 0 to 10 VDC and
0 to 20 mA output signal. This is based upon the
A350E’s setpoint and sensor information, with the offset,
throttling range, and minimum output selected at the
S350P.
For more information on these modules, refer to the
System 350TM S350P Proportional Plus Integral
Temperature Stage Module Product/Technical Bulletin
(LIT-930086).
D350 Temperature Sensor/Setpoint
Display Module
The D350 receives its power, sensor, and setpoint
information from the A350E. A 3-digit Liquid Crystal
Display (LCD) gives a continuous read-out of the
sensed temperature. The setpoint of the adjoining
A350E is displayed when the PRESS FOR SETPOINT
button on the front of the D350 is pushed.
Y350R Power Module
The Y350R provides a convenient method of powering
System 350 Modules from a 120 or 240 VAC power
source. See Figure 5 for a typical wiring diagram where
a Y350R is used to power the A350E. Up to nine
S350A/C stage modules and one D350 can be
operated from a Y350R.
For more information on this module, refer to
System 350TM Y350R Power Module
Product/Technical Bulletin (LIT-930090).

4 System 350 A350E Electronic Cooling Control Product/Technical Bulletin
Dimensions
(40)
Mounting Slots
for No. 6 Screws
DIN Rail
Mount
5 (127)
3/16 (4)
1/2 (13)
(75)
2 15/16
1 9/16
(31)
3 (76)
(22) (22)
Conduit
Hole
2 3/8 (61)
7/8
7/8
A350E
ON
4 (102)
1 3/16
2 3/8 (61)
7/16 (11)
1/4(6)
2 (50)
93/4
(248)
Sensor
Figure 4: A350E and Sensor Dimensions, in. (mm)
Installation and Wiring
The A350E Cooling Control is housed in a compact
NEMA 1 plastic enclosure designed for standard
35 mm DIN rail mounting. Four key-slot mounting
holes on the back of the control case are provided if
surface mounting is required. The A350E may be
connected to a Y350R, as well as other control
modules. Refer to Figures 5 and 6 for proper
arrangement.
Note: When mounting any System 350 module to rigid
conduit, attach the hub to the conduit before
securing the hub to the control enclosure.
!
WARNING: Risk of Electrical Shock.
Disconnect power supply before
making electrical connections to
avoid possible electrical shock or
equipment damage.
Note: For maximum electrical ratings of control, see
the Specifications section or the label inside
the control cover. Use adequate gauge copper
conductors only.
Consult Figures 2, 5, and 6 for proper wiring
configurations and terminal designations.
A350E D350 S350A
Sensor
Load Load
L
1
L
2
Note: Sensor is mounted less than
( ) from the A350E.
50 ft
15.2 m
L1
2
24
VAC
Figure 5: Typical Wiring Diagram for an A350E
Powered by an External Class 2 Transformer

System 350 A350E Electronic Cooling Control Product/Technical Bulletin 5
Sensor Connection
Shielded cable is not generally required for sensor
wiring on runs of less than 50 ft (15.2 m), but is
recommended for lengths greater than 50 ft (15.2 m).
Connect the shield to the COM sensor terminal on the
A350E. (See Figure 2 for terminal location.) Sensor
A99BA-200, which includes a shielded cable, is
available if needed.
Note: At the maximum cable lengths listed in
Table 2, no more than 1F° (0.6C°) error in the
sensed temperature will result due to wire
resistance.
Table 2: Recommended Maximum Sensor
Cable Lengths
Wire Shielded Cable Length*
Gauge Feet Meters
14 AWG 800 244
16 AWG 500 152
18 AWG 310 94
20 AWG 200 61
22 AWG 124 38
* Values provided are for 2-wire stranded cable.
●A variety of A99B Series Temperature Sensors
and mounting hardware are available for use with
the A350E. Connect the sensor to the SEN
terminal and one of the COM terminals on the
four position terminal strip located at the top left of
the printed circuit board, as shown in Figure 6. The
sensor is not polarity sensitive.
●The sensor must be mounted so that it can
accurately sense the temperature of the controlled
medium.
Table 3: Sensor Included With A350E
Controls
Control Sensor Included
A350EA-4C A99BB-25C; Range -40 to 212°F
(-40 to 100°C)
Lead length is 9-3/4 in. (0.25 m).
A350EB-1C No Sensor Included
A350EB-1D No Sensor Included
A350EB-2C No Sensor Included
●For more information regarding sensor options and
installation, refer to the A99B Series Temperature
Sensors Product/Technical Bulletin (LIT-125186).
Load Load Load Load
Shield (Connect
to COM on A350E.)
Sensor
A350E Y350R S350A D350S350A
S350A
120 VAC
24V
COM
COM
SEN
NC COM NO
Figure 6: Typical Wiring Diagram for an A350E Powered by a
Y350R Power Module

6 System 350 A350E Electronic Cooling Control Product/Technical Bulletin
Adjustments
Follow this procedure to set up the A350E for the
desired operation.
1. Remove the A350E’s cover by loosening the
four captive cover screws.
2. Adjust the differential potentiometer (DIFF) as
desired (the number of degrees between relay
energized and de-energized).
Refer to Figure 7 for a sample multistage
application. If a Celsius temperature reading is
desired, place the included Celsius DIFF label over
the Fahrenheit DIFF label (Punch out the tab in the
center before affixing label to the board.)
OFFSET
ON
OFF
ON
OFF
(+)
(-)
Differential
ON
OFF
Differential
ON
OFF
OFFSET
Differential
ON
Differential
OFFSET
OFFSET
A350E
Stage 1
ON = Energized
OFF = De-energized
Differential
Setpoint
Temperature
S350A
Stage 2 S350A
Stage 3
S350A
Stage 4 S350A
Stage 5
OFF
Figure 7: Typical Multistage Cooling Application
3. Replace the cover, fasten in place with the
four captive screws, and move the setpoint dial to
the desired setpoint.
Note: The A350E setpoint is factory calibrated at
midscale to a tolerance of ± 1F° (0.6C°). The
setpoint tolerance at the extreme ends of the
setpoint range in relation to the printed scale
plate can be ± 3F° (1.7C°). The D350 Display
Module is unaffected by this tolerance shift.
Use the D350 display for the most accurate
setpoint selection.
Checkout Procedure
Follow this procedure to verify the A350E control is
connected and functioning properly.
1. Make sure installation and wiring connections are
according to job specifications before applying
power. (Refer to Figure 7 for a sample multistage
application if needed.)
2. Make the necessary adjustments and electrical
connections.
3. Put the system in operation and observe at least
three complete operating cycles before leaving the
installation.
Troubleshooting
If the control system does not function properly, use
the following procedures to determine the cause of the
problem:
1. Check for proper voltage applied to the A350E.
a. Connect a Digital Voltmeter (DVM) between
the 24V (+) and COM (-) terminals located on
the control’s left side terminal block (Figure 2).
•If an external transformer is used, select AC
volts on the DVM and verify that the voltage is
between 20 and 30 VAC.
•If a Y350R Power Module is used, select DC
volts on the DVM and verify that the voltage is
between 16 and 38 VDC.
b. If the DVM reading is within the indicated
voltage range, proceed to Step 2.
c. If the DVM reading is not within the indicated
voltage range, correct the wiring, replace the
Y350R, or replace the external transformer.
2. Check sensor for proper resistance at a given
temperature. (The resistance across the sensor
changes with the temperature of the sensor.)
a. Disconnect power from the A350E control.
b. Disconnect the sensor from the control and
measure the resistance across sensor leads.
c. When measuring the sensor’s resistance, use
an accurate thermometer to measure the
temperature at the sensor.
d. Refer to Figure 8 to determine the optimal
resistance for the measured temperature.
e. If the measured resistance varies substantially
from the optimal resistance for that temperature,
the sensor or wiring must be replaced.

System 350 A350E Electronic Cooling Control Product/Technical Bulletin 7
f. If the sensor’s resistance conforms to the chart
in Figure 8, reconnect the sensor to the control.
g. Reconnect power to the control.
Note: Sensor reading indicated by the D350 may
differ somewhat from thermometer readings
due to sensor tolerances and time constants,
thermometer accuracies, and other factors.
°F Temperature
260
240
220
200
180
160
140
120
100
80
60
40
20
0
-20
-40
500 700 900 1100
Resistance (Ohms)
1300 1500 1700 1900 2100
°C
120
100
80
60
40
20
0
-20
-40
Figure 8: Temperature vs. Resistance Chart
3. Check the A350E for proper operation.
Note: Steps 1 and 2 must be performed first.
a. Set the minimum setpoint jumper to the Off
position.
b. Set the DIFF range to 5F° (2.8C°).
c. Adjust the setpoint dial to at least 10°F (-12.2°C)
above the sensor temperature (Ts) determined in
Step 2 (relay and LED should be Off).
d. Slowly decrease the setpoint until the control
relay and LED turn On, then slowly increase
the setpoint until the relay and LED turn Off.
e. If the relay does not perform as indicated in
Table 4, replace the A350E.
Table 4: A350E Relay Troubleshooting
LED N.O. Relay
Status
Setpoint
Dial Setting
On Closed (Ts)* - Differential
Off Open (Ts)*
* (Ts) is sensed temperature.
For example:
70°F (Ts)
- 5F° (Differential)
65°F (Setpoint Dial Setting)
Repairs and Replacement
Field repairs or calibration must not be made.
A99B Series sensors and replacement controls are
available through the nearest Johnson Controls
representative. See Tables 5 and 6 for ordering
information.
Ordering Information
Table 5: System 350 Products
Item Product Code
Number Description
A350E Cooling Controls
(A350EA-4C Includes the
A99BB-25C Temperature Sensor)
A350EA-4C and
A350EA-1C
A350EA-2C
Range: 10 to 65°F (-12 to 18°C)
Adjustable differential: 1 to 30F° (0.6 to 16.7C°)
Range: 10 to 65°F (-12 to 18°C)
Differential: 2.5°F (1.5°C) fixed
For applications above 65°F (18°C), contact your Johnson
Controls representative.
Digital Temperature Sensor/
Setpoint Display Modules
D350AA-1C
D350BA-1C
Fahrenheit scale
Celsius scale
On/Off Stage Modules S350AA-1C
S350AB-1C
Fahrenheit Scale
Celsius Scale
Slave Stage Module S350CC-1C Dual Scale (°F and °C)
Proportional Stage Module S350PQ-1C Dual Scale (°F and °C)
Power Module Y350R-1C 120 or 240 VAC, 50 or 60 Hz input; Rectified Class 2,
24 VAC output

8 System 350 A350E Electronic Cooling Control Product/Technical Bulletin
Table 6: System 350 Accessories
Item Product Code Number Description
Outdoor Enclosure BOX10A-600R PVC enclosure; includes wire nuts
Wall Mount Plate TE-6001-4 Includes sensor mounting clip
Cover T-4000-2644 For wall mount plate
Conduit Adaptor ADP11A-600R 1/2 in. snap-fit EMT conduit adaptor (box of 10)
Immersion Well WEL11A-601R For liquid sensing applications
DIN Rail Sections BKT287-1R
BKT287-2R
12 in.( 0.3 m) long
39-1/3 in.(1.0 m ) long
DIN Rail End Clamps PLT344-1R Two end clamps
Cable for remote
mounting of D350 Display
Modules
WHA29A-600R*
WHA29A-603R
WHA29A-604R
3 ft (0.9 m)
25 ft (7.6 m)
50 ft (15.2 m)
* WHA29A-600R can also be used to remote mount S350 Stage Modules.
Specifications
Product A350E Electronic Cooling Control
Supply Voltage Y350R Power Module: Input: 120/240 VAC 50/60 Hz
Output: 24 VDC, unfiltered, 10 VA, Class 2
External Source: 24 VAC, 50/60 Hz Class 2 (20-30 VAC)
Note: Only one supply voltage source may be used.
Power Consumption 1.4 VA
Adjustment Setpoint
Range
10 to 65°F (-12 to 18°C)
Differential Adjustment
Range
1 to 30F° (0.6 to 16.7C°)
SPDT Relay Output 120V 208 to 240V
Horsepower: 1/2 1/2
Full Load: 9.8A 4.9A
Locked Rotor: 58.8A 29.4A
Non-Inductive: 10A at 24 to 240 VAC
Pilot Duty: 125 VA at 24 to 240 VAC
Ambient Temperatures Operating: -30 to 150°F (-34 to 66°C)
Shipping: -40 to 185°F (-40 to 85°C)
Humidity 0 to 95% RH non-condensing; maximum dew point: 85°F (29°C)
Sensor Replaceable positive temperature coefficient sensor
Reference resistance: 1035 ohms at 77°F (25°C)
Material Case and cover: NEMA 1, high-impact thermoplastic
Minimum Setpoint Four jumper-selectable settings: 20°F (-7°C), 30°F (-1°C), 40°F (4°C), and Off
Short Circuit Detection De-energizes the relay if the sensor shorts or opens
Agency Listings UL Listed, CCN XAPX, File E27734
UL Listed for Canada, CCN XAPX7, File E27734
The performance specifications are nominal and conform to acceptable industry standards. For application at conditions beyond these
specifications, consult Johnson Controls Application Engineering at [phone]. Johnson Controls, Inc. shall not be liable for damages
resulting from misapplication or misuse of its products.
Controls Group
507 E. Michigan Street
P.O. Box 423 Printed in U.S.A.
Milwaukee, WI 53201 www.johnsoncontrols.com