Joy-it JT-RD6006 User manual

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
LABORATORY POWER SUPPLY
JT-RD6006
1. GENERAL INFORMATION
Dear customer,
thank you very much for choosing our product.
In the following, we will introduce you to what to observe while starting
up and using this product.
Should you encounter any unexpected problems during use, please do
not hesitate to contact us.
The RD6006 is a constant voltage and constant current DC power supply
which can convert voltages down.
It is very easy to handle and the adjustment can either be made by key-
pad or by the encoder or even both.
It is easy and quick to store and recall data and the RD6006 is very con-
nectable with a PC or via WIFI with a handheld device in addition to that
you can use an App for control. On the 2.4 " colour screen you can read
out many values and additional information.

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
SAFETY INSTRUCTIONS
Our product is suitable for up to 70 Volt DC. Working with voltage over 60 V DC is re-
served for trained electricians, because of the hazard of an electric shock which may
cause serious injuries or death. Non-electricians have to use a voltage source below
60 Volt DC.
The power source input interface must be connected
to a 6-70V constant DC power source. The external
sensor cable (as shown on right) must be connected
to the external temperature sensor interface.
The fan interface cannot be connected to other fans. When the output current is
higher than 4A or the system temperature higher than 45 °C, the fan starts to work,
when the temperature is less than 40 °C and output current lower than 3.9 A, the fan
will stop working.
When the system temperature is higher than 80 °C, the output will be shut down
because of OTP. CR1220 is the clock battery. Communication interface is a special
interface, please don’t connect to other modules or cables.
Note: This instruction is corresponding to firmware V1.25.

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
2. TECHNICAL SPECIFICATIONS
3. SCREEN OVERVIEW
Display 2.4 " colour LCD
Input voltage range 6 - 70 V
Output voltage range 0 - 60 V
Output current range 0 - 6 A
Output power range 0 - 360 W
Input voltage accuracy ± 1 % + 5 digits
Output voltage accuracy ± 0.3 % + 3 digits
Output current accuracy ± 0.5% + 5 digits
Battery voltage measurement accuracy ± 0.5% + 3 digits
Input voltage measurement resolution 0.01 V
Output voltage measurement resolution 0.01 V
Current setting measurement resolution 0.001 A
Battery voltage measurement resolution 0.01 V
Constant voltage mode response time 2 ms (at 0.1 - 4 A load)
Constant voltage mode load regulation ± 0.1 % + 2 digits
Constant current mode load regulation ± 0.1 % + 3 digits
Capacity measurement range 0 - 9999.99 Ah
Energy measurement range 0 - 9999.99 Wh
Capacity and Energy statistical error ± 2 %
Output ripple typical 100mV VPP
Sensor temperature detection range -10 - 100°C / 0- 200 ° F
Sensor temperature detection accuracy ± 3° C / ± 6 °F
Working mode Buck mode
Voltage drop > 1V and > 10 %
Screen brightness setting 0 - 5 Level , total 6 level
Working temperature range - 10° - 40 ° C
Current data group
Constant voltage/Constant current status
Protection status indication
Button lock status
Communication Interface
Battery charging indication
Battery-related information
Overcurrent protection value
Overvoltage protection value
Output voltage preset value
Output current preset value
Button tune
Time
Input voltage
Current output voltage
Current output power
Current output current

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
4. DEVICE OVERVIEW
Screen Keypad
Confirm button
Direction buttons
Rotary Encoder
Output switch
Power supply output
positive terminal
Battery charging
positive terminal
Power supply output/
battery charging: nega-
tive terminal
Micro USB Interface
Second function button
Power button
Quick storage button
Current /Overcurrent protection
value setting Voltage/ Overvoltage
protection value setting
Input fuse
External temperature sensor interface
Power Source input interface CR1220 battery socket
Output fuse Fan interface
Communication module interface
4.1. Front Panel:
4.2. Back:

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
1. Operation Menu
In the menu operation, the icon in red or cursor is the currently selected menu; the
icon in blue is the unselected menu; press ENTER to confirm; press the encoder to
cancel or return; press the direction key to move the cursor or switch menu; rotate
the encoder to change the setting; the settings will be automatically saved when re-
turning from the menu page.
Press and hold the 0 button and power on to restore the factory settings; press and
hold the 1 button and power on to restore the factory calibration value; press and
hold ENTER and power on to enter the boot mode.
2. Battery Charging mode
Aer power-on, at battery related information display area, external temperature,
capacity and energy will loop display. When there is output current: electrical charge
and energy are automatically accumulated, and automatically cleared aer shut-
down. The green terminal is connected to the positive pole of the battery and the
black terminal is connected to the negative pole of the battery. Aer the battery is
correctly connected, the battery charging indicator turns red and the battery is con-
nected. Press ON/OFF to start charging, the battery charging indicator turns green.
When the actual output current is lower than 10mA, the output will be shut down au-
tomatically. Batteries with protection board may not be charged. The charging volt-
age and current should be set on your own. It is strongly recommended to use the
original charger to charge the battery.
There is a risk of fire and explosion during the charging process. Non-
professionals should not operate!
3. Main Page Output Voltage and Output Current Setting
Press 'I-SET' button to set the output current value, you can use the encoder to ad-
just the output value directly, press the direction button to move the cursor.
Of course, you can use the keypad to set the value, and press 'ENTER' to confirm.
If you set the wrong value, you can press the encoder to cancel.
Press 'V-SET' button to set the output voltage value, the operation method is similar
to the output current setting. Press 'SHIFT'+ 'I-SET' button or 'SHIFT'+ 'V-SET' but-
ton to set the overcurrent protection / overvoltage protection value. The operation
method is similar to the output current setting. M0 is the default data group when JT-
RD6006 is powered on, manually modify the settings and automatically remember to
M0 aer confirmation.
5. MENU INTRODUCTION

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
4. Data Group Quick Storage and Callout
Press 'MEM' +keypad button 1-9, you can store the output voltage value, output cur-
rent value, overvoltage protection value, overcurrent protection value into the corre-
sponding data group (as shown above), then press 'ENTER' to confirm, or press the
encoder to cancel. Press 'SHIFT' +keypad button 1-9 to quickly call out the saved da-
ta (as shown above). Press 'ENTER' to confirm, or press the encoder to cancel.
5. Keypad lock and unlock
Press 'SHIFT'+'LOCK' to lock or unlock the keyboard. And the keypad will be auto-
matically locked when communication starts,
there will be displayed on the top (can not unlock manually), and the keypad will
be automatically unlocked when the connection disconnected manually.
There will be displayed, the keypad will be automatically unlocked when the
connection disconnected abnormally, and the power-o button can be used when
the keypad is locked.
6. System Setting
Press 'SHIFT'+'MENU' to enter the system setting menu as shown on the right, press
'ENTER' to enter the menu, press direction button to select option, the option in
red is the option be chosen, rotate the encoder
to change this setting.
Turn on the 'Call OK', a confirmation window will
pop up when you quick call out a data group. If
you turn it o, the setting values will be modified
directly when you call out a data group.
Turn on the 'Call out', the output will be turned
on automatically when you call out a data group. If
you turn it o, the output will keep the previous sta-
tus.
Turn on the 'Power On', it will turn on the output
automatically when start. If you turn it o, the out-
put will keep OFF status when started.
Turn on the 'Beeper', you will hear button tune when pressing the button, and
there will be on the top.
If you turn it o, there will not be button tune when press the button, and there will
be on the top.
Turn on the “Logo”, it will display Logo first and then enter the main page when
booting RD6006. If you turn it o, you will enter the main page directly.
The system language supports Simplified Chinese and English for the time being.
The screen brightness can be set from level 0 to level 5.
The communication interface can be set to USB, Wi-Fi or TTL, USB interface is the Mi-
cro-USB interface on the front panel interface, you can see the
on the top when communication starts.
Wi-Fi interface is the Wi-Fi module connected to the communication interface,
you can see the on the top when communication starts (connect mobile phone
by Wi-Fi, but you need to choose Wi-Fi interface first, Wi-Fi module can not be in-
stalled or removed when RD6006 is powered on), TTL is not available for the time be-
ing.
When the interface is changed, you need to reboot RD6006 to apply the modifica-
tion. The baud rate can be set 9600/19200/38400/57600/115200 under USB mode;
The Baud rate under Wi-Fi is fixed at 115200. The device address can be set from 001-
255. You can set the date and time by rotating the encoder, the setting will be
saved immediately aer modification. Please do not set a wrong time, it may cause
the date to not be automatically accumulated. Press the encoder to return, and the
set value will be saved automatically.
Measure is the refresh rate of read back voltage and current on the main page,
you can set it to low, middle and high. Press encoder potentiometer to return and it

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
will be automatically saved.
7. Main Page Style setting
You can press 'SHIFT' + 'MENU' to enter the system setting menu, and then press the
right button to enter the main page style setting menu as shown above. Press ENTER
and then use the direction button to set classic style or curve style. The pattern in red
is the style be chosen. The classic style is the system default style, and the large font
shows the voltage, current and power. The curve style is, as shown above, the color
of the three curves corresponds to the output voltage, current and power. D is the
scale of the ordinate, Press 'ENTER' to start or pause the curve, and the rotate en-
coder potentiometer to scale the ordinate of the curve.
8. Storage Data Setting
You can press 'SHIFT' + 'MENU' to enter the system setting menu, and then press the
right button twice to enter the data storage setting menu as shown below, press EN-
TER to enter the setting menu, the icon in red is the chosen data group, press the di-
rection button to select data group number. Press 'I-SET' button to set the storage
output current value, then rotate the encoder potentiometer the adjust the output
value, press the direction button to move the cursor. You can also set the value with
keypad, press ENTER to confirm. If you set the wrong value, you can press the encod-
er potentiometer to cancel. Press 'V-SET' button to set the storage output voltage
value, the operation method is similar to storage output current setting. Press
'SHIFT'+ “'I-SET' button or 'SHIFT'+ 'V-SET' button to set the storage overcurrent
protection/ storage overvoltage protection value. The operation method is similar to
storage output current value setting. Press Encoder Potentiometer to return, and
the data will be automatically saved.
9. System Information
You can press 'SHIFT' + 'MENU' to enter the system setting menu, and then press the
right button three times to enter the system information menu as shown above. You
can view the SN number, firmware version and system temperature here.

www.joy-it.net
Pascalstr. 8 47506 Neukirchen-Vluyn
Published: 27.02.2020
www.joy-it.net
SIMAC Electronics GmbH
Pascalstr. 8, 47506 Neukirchen-Vluyn
PR
6. ADDITIONAL INFORMATION
Our information and take-back obligations according to the
Electrical and Electronic Equipment Act (ElektroG)
Symbol on electrical and electronic equipment:
This crossed-out dustbin means that electrical and electronic appliances
do not belong in the household waste. You must return the old applianc-
es to a collection point.
Before handing over waste batteries and accumulators that are not en-
closed by waste equipment must be separated from it.
Return options:
As an end user, you can return your old device (which essentially fulfils
the same function as the new device purchased from us) free of charge
for disposal when you purchase a new device.
Small appliances with no external dimensions greater than 25 cm can be
disposed of in normal household quantities independently of the pur-
chase of a new appliance.
Possibility of return at our company location during opening hours:
Simac GmbH, Pascalstr. 8, D-47506 Neukirchen-Vluyn, Germany
Possibility of return in your area:
We will send you a parcel stamp with which you can return the device to
us free of charge. Please contact us by e-mail at [e-mail] or by
telephone.
Information on packaging:
If you do not have suitable packaging material or do not wish to use your
own, please contact us and we will send you suitable packaging.
7. SUPPORT
If there are still any issues pending or problems arising aer your purcha-
se, we will support you by e-mail, telephone and with our ticket support
system.
E-Mail: [e-mail]
Ticket system: http://support.joy-it.net
Telephone: [phone] (10-17 o‘clock)
For further information please visit our website:
www.joy-it.net