Juliana OASIS User manual

21042017 - CH
21042017-CH
OASIS
9'8" x 9'8" (8,8 m2)

B
Dear Customer!
e assembly of your new house requires
a bit of technical knowledge. However, it is
important that the assembly instructions are
followed strict-ly. e assembly instruction
is a combination of text and illustrations. e
proles are packed in separate numbered packs
corresponding to the order in the assembly
instruction. Erect one pack at a time. All nuts
and bolts and ttings are found in bag No. 0
(specied on page 12). Each pack is specied in
separate lists of components.
All detailed illustrations are marked with
symbols:
Seen from inside Seen from outside.
Precautions.
• Assembly must only be carried out in dry
and calm weather.
• Always use working gloves while glazing.
Greenhouse glass has sharp edges,
especially if the glass breaks.
• Assistants and especially children must be
warned that broken glass is an element of
danger. Pick up broken glass at once and
remove it with care.
• We recommend to use protective glasses
while xing the spring wire clips.
• Place the ladder on a level support.
• It is essential to have an assistant.
References
e column marked indicates the
page(s) on which the component is used.
Page 13:
Foundation
e base is not included in this delivery.
However, an original base can be bought
separately. It ensures you a stable and easy to
build base.
If you make your own base the measurements
indicated must be external measurements.
If you buy an original base you furthermore
need about 75 litres of concrete and 6/8
plastic-/concrete pipes of about 800 mm which
are placed in a non-freezing depth for the
fastening of the corner and middle anchors.
e base must be 100% level and square; the
latter is ensured by checking that the two
diagonal measurements are equal.
Tools
e mounting of the greenhouse requires the
tools shown on page 12.
Page 14-27:
Place the components as shown on the
illustration and assemble in the order shown
in the pictures. Do not tighten the nuts
completely until the front gable construction
has been assembled.
Page 13:
(Fastening to the base).
When constructing your own base you have
to drill holes (7 mm) in the ground frame
between all the vertical frames, the greenhouse
is then fastened to the base with screws (A).
Using an original base the greenhouse is
fastened to each vertical bar as shown on
drawing B/C.
Page 24-27:
For an easier assembly we recommend that you
oil the screws for the doors.
Fitting of glass/polycarbonate
Important before glazing!
Make sure that gables and sides are level and
square, and that door(s) and window(s) are
functioning perfectly.
Best order of assembly:
1) Windows – 2) Roof – 3) Doors – 4) Gables
– 5) Sides
Page 30-33:
Glazing (illustration 1 to 8)
Degrease the sheets and frames with spirit.
Start glazing from below, one glass at a time.
Apply a 3 mm silicone line on the vertical
frames where indicated (dotted lines on
the illustration). (A 3 mm line of silicone is
sucient to obtain maximum attachment). If
you do use more than recommended, you can
buy extra tubes.
Spring wire clips and glassholders are to be
tted as shown.
X = Spring wire clips, > = Glassholders
In case of broken glass carefully pull it
outwards and loosen the silicone by means of a
sharp cra knife.
Clean the prole completely before inserting a
new pane of glass.
Page 34-37:
Mounting of polycarbonate
e illustrations at the bottom of page 34/36
show where to mount the polycarbonate plates
and lists. e type indication states the length
in mm. A possible adjustment is made by
means of a ne-tooth saw.
NB! To avoid the formation of algae the
polycarbonate sheets must not come into
contact with the ground. Rest them on a piece
of cardboard.
A-lists are mounted as shown on page 35/37.
Put the sheet into the bottom list, bend the
sheet slightly outwards and put it in the top list.
M-lists are mounted as shown on page 35/37.
Place the upper part of the list under the alu.
prole in the whole length of the sheet and
hereaer click on the list from above.
Sealing of the polycarbonate sheets
e sheets may be sealed against insects.
Close the top end o with alu-tape or silicone.
e bottom only with airstrip tape to let
condensation out (available at your local
dealer).
Now your greenhouse is completely assembled.
However, please notice the following:
Maintenance
• Grease doors (hinges and lock).
• Clean the gutter for leaves, etc.
• Adjustment of windows.
• Replacement of broken glass.
• Clean the house with disinfectant before
and aer the growing season.
Winter Protection
In areas with occurrence of snow we
recommend the following winter protection:
• Support the roof ridge at the centre of the
house.
• Remove greater snow loads from the roof.
• Take precautions against snow falling
down from for instance a tree or a roof.
• Dismount the cylinders for the automatic
window openers, if any (optional extras).
• Secure door(s) and window(s) preventing
wind damage to the house.
Insurance
Please note that not all insurance companies
cover glasshouses automatically. Please
contact your insurance company to ensure an
insurance coverage.
Guarantee
Juliana grants a guarantee of 12 years which
covers replacement of faulty parts. e
guarantee does not cover polycarbonate, glass,
transport, assembly, freight etc.
Juliana grants a guarantee of 2 years on painted
parts, if any. Note that marks in the painting
may occur due to suspension of the proles.
e guarantee is invalid if the greenhouse is
not assembled according to these instructions.
Complaints
All our greenhouses are built to high standards
of quality. However, should a complaint
occur please contact your dealer at once.
Remember to specify the defect by indicating
the greenhouse model and number of the
component and the quality control number.
May we congratulate you on your new greenhouse
GB USA
DEAR CUSTOMER
Congratulaons on purchasing your new
greenhouse. It is important that you follow these
assembly instrucons step-by-step.
The assembly instrucons are a combinaon of text
and illustraons. The proles are packed in separate,
numbered packs corresponding to their order of use
in the instrucons. Assemble one pack at a me.
All nuts, bolts and ngs are contained in bag No.
0 (specied on page 12). Each pack is specied in
separate lists of components.
All detailed illustraons are marked with the
following symbols:
Seen from the inside Seen from the outside
SOME SAFETY PRECAUTIONS
• Assembly must only be carried out in dry and
calm weather.
• Always wear work gloves when installing the
glazing. Greenhouse glass has sharp edges,
especially if it breaks.
• Assistants and especially children must be
warned that broken glass is dangerous. Pick
up all broken glass at once and remove it with
care.
• We recommend that you wear protecve
glasses while xing the spring wire clips.
• Any ladders that are used must be placed on a
level surface.
• It is essenal to have an assistant available.
PAGE 12: TOOLS
Assembling the greenhouse requires the tools
shown on page 12.
PAGE 13: FOUNDATIONS
No base is included with this product. However, an
original base is available separately. This base is easy
to construct and will guarantee you a stable base for
your greenhouse.
If you construct your own base, the specied
measurements must be external measurements.
If you purchase an original base, you will also require
about 75 litres of concrete and six to eight plasc/
concrete pipes of about 800mm. These pipes, which
must be buried at a sucient depth to ensure that
they do not freeze, secure the corner and middle
anchors.
The base must be completely level and square;
the laer can be ensured by checking that the two
diagonal measurements are equal.
ATTACHMENT TO THE BASE
If you construct your own base, you must drill holes
(7mm) in the ground frame between all the vercal
proles. The greenhouse must then be secured to
the base using screws (A).
If you use an original base, the greenhouse must be
secured to each vercal bar as shown on drawings
B/C.
PAGE 14-27: ORDER OF ASSEMBLY
Place the components as shown on the illustraon
and assemble in the order shown in the pictures. Do
not ghten the nuts fully unl the enre sub-frame
has been assembled.
PAGE 18: ROOF
The two automac openers should be frequently
adjusted and at least twice a year in response to
major temperature changes. In winter, it is advisable
to maintain a maximum interval of 40 mm between
the boom of the cylinder and the ghtening screw.
PAGE 20-23: DOORS AND WINDOWS
For easier assembly, we recommend that you oil the
screws for the doors. The glass or polycarbonate for
the door(s) and windows must be ed at the same
me as the proles.
SIDE 25: DOWNPIPE AND FITTINGS
PAGES 26-27: FITTING OF GLASS
Important before assembly!
Make sure that the gables and sides are level
and square and that door(s) and window(s) are
funconing perfectly.
The best order of assembly for the glass:
Windows - Roof - Doors - Gables - Sides
Glass installaon (illustraons 1 to 8)
Degrease the sheets and frames with spirit.
Start glazing from the boom, one pane at a me.
Apply a 3mm silicone bead around the vercal
frames as indicated (the doed lines on the
illustraon). (A 3mm bead of silicone is sucient to
ensure maximum adhesion). If you use more silicone
than recommended, extra tubes can be purchased.
If you accidentally break a pane, carefully pull the
broken glass outwards and loosen the silicone using
a sharp cra knife.
Clean the prole completely before inserng a new
pane of glass.
M-strips are ed as shown on pages 26. Place the
upper part of the strip under the aluminium prole
along the full length of the sheet and then click the
strip into posion from above.
Your greenhouse is now fully assembled. However,
please note the following:
MAINTENANCE
• Grease the doors (hinges and locks).
• Keep the guers free from leaves, etc.
• Adjust the windows as necessary.
• Replace any broken glass.
• Clean the greenhouse with disinfectant before
and aer the growing season.
WINTER PROTECTION
If you ancipate snow during the winter, we
recommend the following winter precauons:
• Support the apex of the roof in the middle.
• Remove any deep snow from the roof.
• Take precauons to prevent snow falling from
a tree or roof, for example.
• Remove the cylinders for the automac
window openers, if ed (oponal extras).
• Adjust the cylinders for the opening of the
hood.
• Secure the door(s) and window(s) to prevent
wind damage to the greenhouse.
WATER AND CONDENSATION
Please note that your greenhouse is not like a
conservatory, for example, and that you should
therefore be aware that the greenhouse may leak
during or aer precipitaon and that condensaon
will occur on the inside of the greenhouse. Good
venlaon will help prevent condensaon.
INSURANCE
Please note that not all insurance companies cover
greenhouses automacally. Please contact your
insurance company to ensure that your greenhouse
is covered.
GUARANTEE
Juliana greenhouses are covered by a 12-year
guarantee, which covers the replacement or repair
of faulty parts. The guarantee does not cover
polycarbonate, glass, transport, assembly, freight,
etc.
Juliana greenhouses are covered by a two-year
warranty on painted parts, where ed. Note that
marks on the paint may occur due to suspension of
the proles.
The guarantee will be void if the greenhouse is not
assembled in accordance with these instrucons.
COMPLAINTS
All our greenhouses are built to the highest quality
standards. However, should you experience any
problems, please contact your dealer at once. When
describing the defect, please state the greenhouse
model, the component number and the quality
control number.
Any suspension marks or shiny ends on painted
Juliana proles will not be visible aer the
greenhouse has been assembled.
Congratulaons on your new greenhouse, which we
hope will bring you a lot of pleasure for many years
to come.
Yours sincerely,
Juliana Drivhuse A/S

Survey
12
13
14 - 17
18 - 19
20 - 21
26 - 27
22 - 23
24 - 25
Tools
Fittings
0#
78
79
84
602
14-23 140
14-23 160
14-23 20
14-25 10
13,5
2,5 mm
6 mm
79A 14-25 10
140
160
20
10
8,8
10

Accessories
13
13,5 3676 36765200
13,5
1100
1468
3676
M6x10
M6x40
7
24
6
30
2
B
A
4,2x16 10
C
12
45 3
Y
XZ
S
1103 1470
X Y Z S D
1
1
1
345
345
345
M6
1100
1468
3676
994
995
638
989
11-1
11-2
996
850 14
989
989
11-1
11-1
741/1100
741/1100
989
994
995
996
1468
7 mm
850
638
1468
11-1
11-2 1
2
345
Assembly support Assembly support
3
D
8,8
8,8 2958 29584183 741 1470
29582958 3
741741 2
1
ONLY 13,5
24
0
24
10
1
1
9
4
Foundation

14
10
12
33
05
x4
78N - M6x11
78 - M6x11
x2
33
11
06
79N - M6
x4
78 - M6x11
x2
78N - M6x11
1
3
2
09
11
1
1
#mm 13,5
00
11
09
10
1468
1920
1101
1101
34
3648
1
2
1
1
1
2
1
00
12 cm.
2
3
M6x15
M6x15
32-5
00
11
11 31
31
33
33
09
10
32-5
33
3608
1931
M6x11
M6x11
M6x11
M6x11
90
90
90 1100 2
4
11
90
4
31
8,8
09
10
742
742 1
1
1
2
32 2890 1
34
2890
90 742 2
1
2
31 1800 2
Front gable
8,8

15
Sides
2
3
1
32-6
31
31
34
33
33
30
32-6
33
2
3
1
30
31
31
31
31
33
M6x11
M6x15
M6x15
M6x15
M6x15
M6x11
M6x11
M6x11
M6x11
M6x11
M6x11
M6x11
14
14
500
500
500
32-6
34
32-6
33
2#mm 13,5
30
34
31
33
3614
1800
3608
1931
32-6
2
2
8
2
4
3658
14 1800 4
14
x2
500 4
OBS!
Windows
OBS!
34 2890 2
32-6
2890 2
4
4
6
30 2896
8,8
2

16
2
3
1
33
30
31
31
32-6
31
30
32-6
33
2
13
30
31
31
31
31
33
3#mm 13,5
30
34
31
33
3614
1800
3608
1931
32-6
1
1
4
1
2
3658
M6x15
M6x15
M6x15
M6x15
M6x11
M6x11
M6x11
M6x11
M6x11
M6x11
8,8
34 2890 1
2
32-6
2890
3
30
1
2896
1
Rear gable

4
56
09
13
11
6
79 - M6
00
5
6
7
7
14
32-5/6 32-5/6
14
10
93 x 4
3#mm 13,5
93 4
14
8,8
4
Sides
17

18
Roof
19
1
1
4#mm 13,5
49 2544 4
1413 390x390
49
49
49
49
413
4949
4949
2xM6x11
358 16
3
2
358
358
49
2x58
2
51-5
51-5
51-6
51-6
813
813
1643
1643
4
4
4
4
507 2
414 1
49 1993 4
8
4
2
1
1
8,8
51 1500 4
4

3
5
4
32-5/632-5/6
49
51-6
51-5
5
4
6
51-6
58
49
51-6
32-5/6
6
507
416
78+79
78+79
40mm
51
51-6
51-5
365
110
Roof
19

20
Door
3 mm
B
5#mm
55
56
57
58
60
517
517
1075
1075
812
812
578
578
4
1
1
1
1
1
2
1
1
4
61 651
62
1
2
3
5
6
4
7A
8
63
59
62
00
10
55
61
55
11
66
64
09
11
60
713
62
62
59
57
55
56
55
58 65
67
68 69
68 69
68 69
68 69
691
299
9
10
11
12
691
693
691
693
7B
04 03
59
62
63
64
65
66
1075
812
1075
5#mm
67
68
69
691
662 5x80
1
2
4
4
1
4
1
12
664
713
1011
299
36
4,2x13
1
1
A
662 - 5,0x80
3 mm.
712
3,5x16
1
03 261x578
1
04 261x517
Olie/Oil/
Öl/Huilef
693 2
953 3,5x16 8

21
Door
64
1011
4,2x13
11
713
58
1 2 3
4
9
57 55
662 - 5,0x80
04
56
57
61
664 - 3,5x16
57
55
68
55
62
67
59
69A
62
56
7 8
10
713
58
691
55 60 67
65
06
11
68
299
12
662 - 5,0x80 04
3 mm.
662 - 5,0x80
3 mm.
68
662 - 5,0x80
3 mm.
3 mm.
3 mm.
662 - 5,0x80
953 - 3,5x16
2,5 mm.
662
5,0x80
664 - 3,5x16
69
664 - 3,5x16
662
5,0x80
10 10
11 11
693
7A
7B
62
66

22
Windows
2
34
1
71
70
71
72
70
7172
71
3
4
5
1
2
70
71
71
72
73E 73
73C
3 mm. 3 mm.
6
#mm
70
71
72
73
73E
738
611
738
510
2
4
2
2
2
2
73C
3 mm.
3 mm
77a 2
75 2
634 4
6
93-1 4
664S
94-4
8
4

23
Windows
5 6 8
11
10
12
9
8
72
77
78A - M5 73B
73C
73D
73A - M5x10
73
94-4
77
634
75
94-4
77
78B - M5x20
70
7
13
13
12
11
77a
10
9
75 634
664 - 3,5x16
75
73E
77
93-1
1033mm
30

24
Downpipe
441A
78
501
2
4
1
34
451
14
440
1
2
5
4
8
3
3
6
79
10
11
15
14
16
15
3
451
441B
76A - 3,5x6,5
958 - M5x10
3 mm.
7
#mm
13,5
501
440
441A
441B
76A
280
470
451
4
4
4
4
8
155
2
958 16
3,5x6,5
M5x10
1650
502 8
8,8
4
4
4
4
8
8
2
155
16
502

25
Downpipe
13
5
11
55
62
7
89
12 14
14
60
14
669 - M4
66
2,5 mm.
953 - 3,5X16
470
Silicone
Silicone
55
62 60
66
2,5 mm.
953 - 3,5X16
470
6
99B - 4,2x16
9
351
470 668 - M6x16
14 mm
10
15
280
34
Silicone

26
#
1800
mm
M80
13,5
H
H
G
G
A
A1
A
A1 A
A
B2
B2
B1B1
B
B1
B2
F
C
D
Silicone
6
350
M1800
M1800
M1800
M1800 M1800 M1800
M1800 M1800 M1800
M1800
M1800
M1800 M1800 M1800
M1800 M1800
M1800 M1800 M1800 M1800 M1800 M1800
M1800
M1800
≈299cm
3 mm. Tempered glass

#
A
3 mm
700 x 1797
A1 341 x 1797
C700 x 1072
D700 x 610
B700x1646/1910x240x1910\1646
B1 700x1620/810
G517 x 700
H578 x 700
13,5
15
2
2
2
4
8
2
2
2
A
3 mm.
Silicone
M
A
B
C
3 mm.
3 mm.
3 mm.
Rubber list
3 mm.
2,8 mm. 2,8 mm.
RUBBER LIST - FOR UK MARKET
413
1
2
3
STEP
STEP
STEP
B
B2 687x790/0
F 700x115
8
3 mm. Tempered glass
27

28
#
1800
mm
M60
8,8
H
H
G
G
A
A A
A
B2
B2
B1
B1
B1
B2
F
C
D
B1
Silicone
5
350
M1800
M1800
M1800
M1800 M1800
M1800 M1800 M1800
M1800 M1800
M1800 M1800
M1800 M1800 M1800 M1800 M1800 M1800
≈277cm
3 mm. Tempered glass

29
29
#
A
3 mm
700 x 1797
C 700 x 1072
D 700 x 610
B1
G517 x 700
H 578 x 700
8,8
12
2
2
2
2
2
A
3 mm.
Silicone
M
A
B
C
3 mm.
3 mm.
3 mm.
Rubber list
3 mm.
2,8 mm. 2,8 mm.
RUBBER LIST - FOR UK MARKET
413
1
2
3
STEP
STEP
STEP
B
B2 687x790/0
F 700x115
8
700 x 1482/810 4
3 mm. Tempered glass