Jung Mini basic User manual

Motion detector mini basic
Motion detector mini basic
Art. no.: BM360MBWW
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. During installation and cable routing, comply with the regulations and
standards which apply for SELV circuits.
Do not press on the sensor window. Device can be damaged.
The device is not suitable for use as a burglar alarm or other alarm.
These instructions are an integral part of the product, and must remain with the end customer.
2 Intended use
Intended use
– Brightness-independent detection of motion indoors.
– Connection to the KNX devices mentioned under accessories e.g. Multistation or push
button interface for the automatic switching of loads.
– Power supply via the unchoked output of a KNX power supply or power supply unit with
safety extra-low voltage (SELV).
– Clamp mounting in suspended ceilings.
– Ceiling mounting on fixed ceilings in appliance box according to DIN 49073 or surface-
mounted housing (see accessories)
3 Function
– Brightness-independent detection of motions in the detection field
– Switch on: After detecting motion
– Switch off: No motion in the detection field and run-on-time elapsed
– Potential-free electronic switching contact
4 Information for electrically skilled persons
4.1 Fitting and electrical connection
Selecting installation location
The motion detector is installed on the ceiling and monitors the surface under it.
￭ Select a vibration-free installation location. Vibrations can lead to unwanted switching.
￭ Avoid interference sources in the detection area. Interference sources, e.g. heaters, vent-
ilation, air conditioners, and cooling light bulbs can lead to unwanted detections.
If necessary, the detection field can be limited using the push-on cover in order to minim-
ize the influence of interference sources.
1 / 6
82403103 29.09.2020
J0082403103

Motion detector mini basic
Motion detection
Figure1: Tangential and radial direction of motion
The device has a detection field of 360°. The diameter of the detection field depends on the in-
stallation height and the direction of motion of persons in the detection field (Figure 1). The de-
tection field becomes larger the greater the installation height, while the detection density and
sensitivity are reduced at the same time. The following applies to an installation height of 3 m:
1: Range for tangential motion on the ground Ø approx. 6 m
2: Range for radial motion on the ground Ø approx. 5.5 m
DANGER!
Electrical shock on contact with live parts in the installation environment.
Electrical shocks can be fatal.
Before working on the device, disconnect the power supply and cover up live parts
in the working environment.
Create a mounting opening in the suspended ceiling
Figure2: Mounting in the suspended ceiling
(1) Spring clamp
(2) Cable fixation
2 / 6
82403103 29.09.2020
J0082403103

Motion detector mini basic
(3) Terminal
(4) Motion detector
(5) Design ring
The environment in the suspended ceiling must be dry.
Max. thickness of the suspended ceiling approx. 25 mm. Installation depth min. 35 mm. Dis-
tance between concrete ceiling and suspended ceiling min. 20 mm (Figure 2).
￭ Create ceiling cut-out Ø 44...45 mm(Figure 2).
Connecting the device
Figure3: Clampable conductor cross-section
Recommended line J-Y(St)Y 2×2×0.8 (2 wire pairs, conductor diameter 0.8 mm this corres-
ponds to a conductor cross-section of 0.5 mm²).
For the cable length, also observe the information in the instructions for the device to be con-
nected.
￭ Use the unchoked output of a KNX power supply or power supply unit with safety extra-
low voltage as power supply.
￭ Connect the connection cable to device connection terminal (3) (Figure 2).
Connection in general
Terminal assignment of motion detector
Terminal Connection
DC24V + Power supply +
DC24V – Power supply GND
A+ Switching output +
A– Switching output –
Figure4: Connection in general
For connection diagrams for various KNX devices, see accessories
Figure5: Connection to Multi station
3 / 6
82403103 29.09.2020
J0082403103

Motion detector mini basic
Figure6: Connection to Binary input 6-gang
Figure7: Connection to Binary input 8-gang, 230 V
Figure8: Connection to Push-button interface, 2-gang, Push-button interface, 4-gang
Figure9: Connection to Flush-mounted blinds actuator, 1-gang with satellite input
Figure10: Connection to Switch actuator, 2-gang
4 / 6
82403103 29.09.2020
J0082403103

Motion detector mini basic
Figure11: Connection to Valve drive (motor-operated) with controller
(6) Motion detector mini basic
(7) Multi station, Art. no.:23066REGHE
(8) Binary input 6-gang, Art. no.:2116REG
(9) Binary input 8-gang, 230 V, Art. no.:2118REG
(10) Push-button interface, 2-gang, Art. no.: 2076-2T/Push-button interface, 4-gang, Art.
no.: 2076-4T
(11) Flush-mounted blinds actuator, 1-gang with satellite input, Art. no.:2501 UP
(12) Switch actuator, 2-gang, Art. no.:2132.6UP
(13) Valve drive (motor-operated) with controller, Art. no.:2177SVR
Mounting the device in the suspended ceiling
￭ Secure the connection cable with the enclosed cable fixation (2) (Figure 2).
￭ Bend back the spring clamps (1) and push the motion detector (4) into the suspended
ceiling (Figure 2).
￭ Attach the large design ring (5) and rotate it in clockwise direction (Figure 2).
5 Technical data
Rated voltage DC 24 ... 32 V SELV
Standby power < 0.1 W
Current consumption max. 4 mA
Ambient temperature -5 ... +45 °C
Storage/transport temperature -25 ... +70 °C
Relative humidity 10 ... 100 % (no moisture condensation)
Protectionclass III
Degree of protection IP44
Detection angle 360°
Installation height 3 m
Detection field Ø approx. 6 m
Run-on time approx. 10 s
Switching output
Electric strength 40 V
Current carrying capacity max. 50 mA
Connected load max. 150 mW
Dimensions
Dimensions Ø×H 53.5 × 38 mm (with design ring)
Ceiling cut-out Ø×D 44 × 35 mm
Cable length max. 30 m
5 / 6
82403103 29.09.2020
J0082403103

Motion detector mini basic
6 Accessories
Power supply 160 mA Art.-no.: 20160REG
Power supply 320 mA Art.-no.: 20320REG
Power supply 640 mA Art.-no.: 20640REG
Power supply 1280 mA Art.-no.: 21280REG
Multi station Art.-no.: 23066REGHE
Binary input 6-gang Art.-no.: 2116REG
Binary input 8-gang, 230 V Art.-no.: 2118REG
Push-button interface, 2-gang Art.-no.: 2076-2T
Push-button interface, 4-gang Art.-no.: 2076-4T
Flush-mounted blinds actuator, 1-gang with
satellite input
Art.-no.: 2501 UP
Switch actuator, 2-gang Art.-no.: 2132.6UP
Valve drive (motor-operated) with controller Art.-no.: 2177SVR
Flush mounting set Art.-no.: PMM-UP-SET-WW
Surface mounting set Art.-no.: PMM-AP-SET-WW
7 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de
6 / 6
82403103 29.09.2020
J0082403103