Jung FMAS10ZS User manual

eNet radio switch/push-button actuator in SCHUKO housing
eNet radio switch/push-button actuator in SCHUKO housing
Art. no.: FMAS10ZS
Operating instructions
1 Safety instructions
Electrical devices may only be mounted and connected by electrically skilled persons.
Serious injuries, fire or property damage possible. Please read and follow manual fully.
Danger of electric shock. Always disconnect the device from the socket outlet before carrying
out work on the device or load.
Danger of electric shock. Device is not suitable for disconnection from supply voltage. Even
when the device is switched off, mains voltage may be present on the load, because only 1 pole
is switched off.
Adapter plugs may not be connected in series and must be easily accessible.
The radio communication takes place via a non-exclusively available transmission path, and is
therefore not suitable for safety-related applications, such as emergency stop and emergency
call.
These instructions are an integral part of the product, and must remain with the end customer.
2 Device components
Figure1
(1) SCHUKO ®socket with increased contact protection
(2) Red status LED, covered
(3) Button Prog
3 Intended use
– Switching of lighting
– Operation with suitable eNet radio transmitters
– Receiving and repeating eNet radio telegrams (repeater function)
– Indoor mounting in SCHUKO® socket or socket with ground pin
1 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Product characteristics
– Status feedback to radio transmitter
– Scene operation possible
– Switchable output with Prog button
– Status indicator via LED
The repeater function can be activated via the eNet radio diagnostics device and the eNet
Server.
Can be set with eNet server:
– Push-button function
– Flash function
– Repeater function
– Run-on time
– Switch-on delay / switch-off delay
– Operation as NO or NC contacts
– Switch-off warning
– Minimum switching repeat time
– Operation locks
– Continuous on, Continuous off
Supplementary functions with eNet Server:
– Fully encrypted radio transmission (AES-CCM) from eNet Server software version 2.0
– Update of the device software
– Reading of error memory
Behaviour after mains voltage return
The response after mains voltage return can be configured with the eNet server. Default setting:
Off.
4 Operation
When operating with the eNet Server, operation and signalling could vary from what is de-
scribed here.
Operation with radio transmitters
Operation is with radio transmitters, please observe the radio transmitter instructions.
Operation with Prog button
￭ Press Prog button briefly.
The load switches on or off.
Status LED lights up: output is switched on.
Status LED off: output is switched off.
5 Information for electrically skilled persons
5.1 Fitting and electrical connection
DANGER!
Electrical shock when live parts are touched.
Electrical shocks can be fatal.
Always disconnect the device from the socket outlet before carrying out work on the
load!
2 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Connecting the device
To ensure good transmission quality, keep a sufficient distance from any possible sources of in-
terference, e.g. metallic surfaces, microwave ovens, hi-fi and TV systems, ballasts or trans-
formers.
￭ Insert device into a socket outlet.
￭ Insert load into the device.
￭ Carry out commissioning (see Commissioning chapter).
5.2 Commissioning
The actuator can also be commissioned with eNet Server as an alternative to the commis-
sioning described here.
Connecting actuator to radio transmitters
Load is switched off.
￭ Press the Prog button for longer than 4 seconds.
The load switches on.
The status LED flashes after 4 seconds and the load switches off. The actuator is in pro-
gramming mode for approx. 1 minute.
￭ Switch radio transmitter to programming mode (see radio transmitter instructions).
￭ Trigger telegram on the radio transmitter.
The status LED of the actuator lights up for 5 seconds.
The actuator is connected to the radio transmitter. The actuator and radio transmitter exit
the programming mode automatically.
If the status LED of the actuator flashes 3 times at 1-second intervals for approx.
5 seconds, then the programming procedure was not successful. All the memory locations
in the actuator or radio transmitter are occupied.
All On and All Off buttons of a radio transmitter are connected to the actuator automatic-
ally as soon as the first connection to the radio transmitter takes place.
Scene buttons must be connected separately.
Disconnecting connection to a radio transmitter
￭ Carry out the same steps as when connecting (see Connecting actuator to radio transmit-
ters).
The status LED flashes quickly for 5 seconds. The actuator is disconnected from the radio
transmitter. The actuator and radio transmitter exit the programming mode automatically.
If there several connections or scene buttons for a radio transmitter, all connections must
be disconnected individually.
All On and All Off buttons of a radio transmitter are disconnected automatically as soon as
the last connection of the corresponding output to the radio transmitter is disconnected.
Manual disconnection is not possible.
Resetting the device to the factory setting
All connections to radio transmitters are disconnected and parameters are reset to default set-
ting.
The connections in the radio transmitters are preserved and must be deleted separately.
Load is switched off.
￭ Press the Prog button for at least 20 seconds.
The load switches on.
The status LED flashes after 4 seconds and the load switches off. The status LED flashes
faster after 20 seconds.
3 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
￭ Release Prog button and press briefly once again within 10 seconds.
The status LED flashes more slowly for approx. 5 seconds.
The device is reset to default setting.
6 Technical data
Rated voltage AC 230 V~
Mains frequency 50 / 60 Hz
Ambient temperature -5 ... +35 °C
Degree of protection IP20
Switching current at 35 °C
Ohmic 16 A (AC1)
Fluorescent lamps 4AX
Minimum switching current AC 100 mA
Contact type μ
Standby power 0.5 W
Connected load at 35°C
Incandescent lamps 2300 W
HV halogen lamps 2000 W
Electronic transformers 1500 W
Inductive transformers 1000 VA
HV-LED lamps typ. 500 W
Compact fl lamp. typ. 500 W
Fluorescent lamps, uncompensated 920 VA
Capacitive load 690 VA (560 μF)
Dimensions W×H×D 57×142×78 mm
Radio frequency 868.0 ... 868.6 MHz
Transmission capacity max. 20 mW
Transmitting range in free field typ. 100 m
Receiver category 2
7 Parameter list
The device parameters can be changed with the eNet server:
Device and channels
Parameters Setting options, Basic setting Explanations
Function Light, switching, unused
Basic setting: Light
Light
The channel is integrated for
the "Lighting" central function
in the eNet SMART HOME
app.
Switching
The channel is not integrated
in any central function.
Unused
The channel is not displayed
4 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Parameters Setting options, Basic setting Explanations
in the eNet SMART HOME
app and is disabled for use in
the commissioning interface.
Operating mode Switching operation
Push-button operation
flashing
Continuous on
Continuous off
Basic setting: Switching oper-
ation
Switching operation
After switch-on, the device re-
mains stable in the "On" state,
and stable in the "Off" state
after switch-off.
Push-button operation
The device switches "On"
when any channel button of a
radio transmitter is pressed
and "Off" when the button is
released. It is irrelevant
whether the "On" or "Off"
channel button is pressed.
flashing
Switch-on starts flashing and
switch-off stops flashing. The
default flash frequency is 1
Hz. This frequency is also the
maximum flash frequency.
The flash frequency can be
changed using parameters.
The parameter "Switch-off
delay" is used for the pulse
time and the parameter
"Switch-on delay" for the
pause time.
Continuous on
The output switches to con-
tinuously "On". All operations
of radio transmitters and the
Prog button are ignored.
Continuous off
The output switches to con-
tinuously "Off". All operations
of radio transmitters and the
Prog button are ignored.
Advanced device settings
Parameters Setting options, Basic setting Explanations
Manual commissioning On, Off
Basic setting: On
Disables manual commission-
ing for all device channels. In
the "Off" setting, the device
cannot be reset to the factory
setting.
5 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Parameters Setting options, Basic setting Explanations
Repeater mode On, Off
Basic setting: Off
In addition to its other func-
tions, the device can be used
as a repeater. In the "On" set-
ting, the device repeats all the
received telegrams.
Channel settings
Parameters Setting options, Basic setting Explanations
Switch-on delay 0 s … 24 h
Basic setting: 0 s
The load switches on after a
delay. Repeated switch-on
commands restart the delay
time. If the load has not yet
been switched on due to the
delay when a switch-off com-
mand comes, then the load
will remain off.
In Flashing operating mode,
the pause time is set using
this parameter.
Comment: The set times apply
to operation using radio trans-
mitters. The relay is switched
immediately when the Prog
button is pressed.
Switch-off delay 0 s … 24 h
Basic setting: 0 s
The load switches off after a
delay. Repeated switch-off
commands restart the delay
time. If the load has not yet
been switched off due to the
delay when a switch-on com-
mand comes, then the load
will remain on.
In Flashing operating mode,
the pulse times are set using
this parameter.
Comment: The set times apply
to operation using radio trans-
mitters. The relay is switched
immediately when the Prog
button is pressed.
Run-on time 0 s … 24 h
Basic setting: 0 s
As soon as a run-on time has
been entered, the actuator will
no longer remain on perman-
ently, but only for the length of
the run-on time. The run-on
time is restarted if actuation is
repeated. This parameter is
directly connected to the
"Manual switch-off of run-on
time" parameter.
Comment: The set times apply
to operation using radio trans-
mitters. The relay is switched
immediately when the Prog
button is pressed.
6 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Parameters Setting options, Basic setting Explanations
Manual switch-off of the run-
on time
On, Off
Basic setting: Off
Allows manual switch-off of a
running run-on time. If the
parameter is switched off,
then a switch-off command
will also switch the actuator
on. This parameter is directly
connected to the "Run-on
time" parameter.
Operating hours 0...65535
Basic setting: Current value
The time is counted during
which the load is physically
switched on (relay contact
closed).
This parameter can be reset
to "0", for example after ex-
changing the load.
The Reset button is used to
reset the counter to "0". The
device must be programmed
to apply the change.
Extended channel settings
Parameters Setting options, Basic setting Explanations
Operating mode Switching operation
Push-button operation
flashing
Continuous on
Continuous off
Basic setting: Switching oper-
ation
See Device and channels.
Manual commissioning On, Off
Basic setting: On
Blocks manual commissioning
for the device channel. In the
"Off" setting, the device can-
not be reset to the factory set-
ting.
Local Operation On, Off
Basic setting: On
Blocks the output for operation
using the Prog button.
Behaviour on voltage return On
Off
Last value
Configured brightness
Basic setting: Off
Defines the behaviour of the
output after voltage return.
Timer behaviour, voltage re-
turn
Off
Restart
Basic setting: Off
Specifies whether the timers
for switch-on delay, switch-off
delay and run-on time remain
off after voltage return or
whether they restart. Directly
connected to the parameters
"Switch-on delay", "Switch-off
delay" and "Run-on time".
7 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Parameters Setting options, Basic setting Explanations
Behaviour after the end of the
disabling function
On
Off
no change
Last value
Basic setting: No change
Behaviour of the output when
a block is removed.
Manual saving of the scene
values
On, Off
Basic setting: On
Disables the saving of the cur-
rent actuator state (On/Off) as
scene value in an actuator for
a command via a transmitter.
Switch-off warning On, Off
Basic setting: Off
If the switch-off warning is act-
ive, the light is not switched off
directly. The light goes off 30,
15 and 6 seconds before per-
manent switch-off. During the
switch-off warning, a switch-
on telegram effects direct
switch-on. It is not possible to
terminate the time using a
switch-off telegram.
Priority, lock-out protection 0...4
Basic setting: 1
Specifies the priority for recall-
ing and removing a scene of
type Lock-out protection for
the channel.
Activate lock-out protection
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on activating the lock-
out protection.
Deactivate lock-out protection
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the
lock-out protection. Only vis-
ible when the priority for the
lock-out protection is 0.
Priority, restraint 0...4
Basic setting: 2
Specifies the priority for recall-
ing and removing a scene of
type Restraint for the channel.
Activate forced operation
switching state
On, Off
Basic setting: On
Defines the behaviour of the
output on activating the forced
operation.
Deactivate forced operation
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the
forced operation. Only visible
when the priority for the forced
operation is 0.
Priority, wind alarm 0...4
Basic setting: 3
Specifies the priority for recall-
ing and removing a scene of
type Wind alarm for the chan-
nel.
Activate wind alarm switching
state
On, Off
Basic setting: Off
Defines the behaviour of the
output on activating the wind
alarm.
8 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Parameters Setting options, Basic setting Explanations
Deactivate wind alarm switch-
ing state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the
wind alarm. Only visible when
the priority for the wind alarm
is 0.
Priority, sun protection 0...4
Basic setting: 0
Specifies the priority for recall-
ing and removing a scene of
type Sun protection for the
channel.
Activate sun protection switch-
ing state
On, Off
Basic setting: On
Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun protec-
tion is 0.
Deactivate sun protection
switching state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the sun
protection. Only visible when
the priority for the sun protec-
tion is 0.
Priority, twilight 0...4
Basic setting: 0
Specifies the priority for recall-
ing and removing a scene of
type Twilight for the channel.
Activate twilight switching
state
On, Off
Basic setting: On
Defines the behaviour of the
output on activating the twi-
light function.
Deactivate twilight switching
state
On, Off
Basic setting: Off
Defines the behaviour of the
output on deactivating the twi-
light function. Only visible
when the priority for the twi-
light function is 0.
Switch off brightness over-
shoot
On, Off
Basic setting: On
Allows automatic switch-off
according to the brightness. If
the parameter is On, then the
light controller switches off
automatically when the bright-
ness setpoint is greatly ex-
ceeded. This parameter is not
yet active, as a light controller
has not yet been implemen-
ted.
Switch on brightness under-
shoot
On, Off
Basic setting: Off
Allows automatic switch-on
according to the brightness. If
the parameter is On, then the
light controller switches on
automatically when the bright-
ness setpoint is greatly under-
shot. We recommend only us-
ing the parameter in connec-
tion with the parameter
"Switch-off on brightness over-
shoot". This parameter is not
9 / 10
82592223 15.12.2020
J0082592223

eNet radio switch/push-button actuator in SCHUKO housing
Parameters Setting options, Basic setting Explanations
yet active, as a light controller
has not yet been implemen-
ted.
Invert switching output On, Off
Basic setting: Off
Inverts the switching output
from NO contact function
(factory setting) to NC contact
function
Minimum switching repeat
time
100 ms ... 10 s
Basic setting: 100 ms
Limits the switching speed of
the device by increasing the
value, in order to protect the
load, for example. Only when
the set time has elapsed is
switching possible again. The
last command during the
blocking time is executed after
a delay. The switching repeat
time starts after each switch-
ing operation.
Information window
During channel selection in the Information window, the following settings can be made or val-
ues displayed.
Display value Explanations
Load state The load can be switched on or off.
Restraint Display of forced position status.
Operating hours Display of the operating hours since the last
restart in the Settings window Einstellungen.
8 Conformity
Hereby Albrecht Jung GmbH & Co. KG declares that the radio system type
Art. no. FMAS10ZS
corresponds to the directive 2014/53/EU. You can find the full article number on the device. The
complete text of the EU Declaration of Conformity is available under the Internet address:
www.jung.de/ce
9 Warranty
The warranty is provided in accordance with statutory requirements via the specialist trade.
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de
10 / 10
82592223 15.12.2020
J0082592223