Jung Home User manual

Operating instructions
JUNG HOME push-button 1-gang
Art. no. BT..17101..
JUNG HOME push-button 2-gang
Art. no. BT..17102..
24.02.2023
32405203 J0082405203
ALBRECHT JUNG GMBH & CO. KG
Volmestraße 1
58579 Schalksmühle
GERMANY
Telefon: [phone]
Telefax: [phone]
[email protected]
www.jung.de

Table of Contents
1 Safety instructions.............................................................................................................3
2 Device components...........................................................................................................3
3 Intended use .....................................................................................................................4
4 Product characteristics......................................................................................................4
5 Operation ..........................................................................................................................7
5.1 Operation via extensions ....................................................................................... 8
6 Mounting and electrical connection...................................................................................9
7 Commissioning via app ...................................................................................................10
8 Resetting the device to the factory setting ......................................................................11
9 Technical data.................................................................................................................12
10 List of functions and parameters .....................................................................................14
11 Conformity.......................................................................................................................26
12 Warranty..........................................................................................................................26
2 / 26
32405203 24.02.2023
J0082405203
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang

1 Safety instructions
To avoid possible damage, read and follow the following instructions:
Installation only by persons with appropriate knowledge and experience in the
following areas:
– 5 safety regulations and standards for the installation of electrical systems
– Selection of suitable tools, measuring devices, installation materials and, if ne-
cessary, personal protective equipment
– Installation of the installation material
– Connection of devices to the building installation under consideration of local
connection conditions
Improper installation endangers your own life and the lives of users of the electrical
system and there is a risk of serious damage to property, e.g. through fire. You are at
risk of personal liability for personal injury and damage to property.
Contact an electrical fitter!
Danger of electric shock. If the device exhibits any visible damage, it must not be
used any longer. Immediately disconnect device from mains by switching off all asso-
ciated circuit breakers.
Danger of electric shock. Device is not suitable for disconnection from supply voltage
because – depending on the insert used – mains potential even is applied on the load
when the device is switched off. Always disconnect before carrying out work on the
device or load. To do so, switch off all associated circuit breakers.
The device must not be used for applications from the area of safety engineering,
such as emergency stop, emergency call, smoke extraction.
Read the instructions in full, observe them and keep them for future reference.
You can find more information on JUNG HOME at www.jung.de/JUNGHOME
2 Device components
Image1: JUNG HOME push-button 1-gang
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
3 / 26
32405203 24.02.2023
J0082405203

Image2: JUNG HOME push-button 2-gang
(1) System insert
(2) Design frame
(3) Operating cover
(4) Status LED
LED indication during operation
Green* Output is switched on
Venetian blind, shutter, awning moving
Orange* Output is switched off (rocker operating concept)
Venetian blind, shutter, awning stationary
Orientation LED (button operating concept)
Red Disabling function active, e.g. continuously on/off
Blue, triple flashing Time has not been set, e.g. due to extended power failure
Flashing green/red Device update is being performed
Red, triple flashing Error message (cover was previously connected to another
system insert)
* Colour adjustable
3 Intended use
– Manual and automatic operation of e.g. venetian blinds, shutters, awnings
lighting or fans
– Wireless connection to devices from the JUNG HOME system
– Operation with system insert for dimming, switching, Venetian blind or 3-wire
extension
4 Product characteristics
– Commissioning and operation using JUNG HOME app on mobile end device
(smartphone or tablet) via Bluetooth
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
4 / 26
32405203 24.02.2023
J0082405203

– Operation of top, bottom and full surface with up to two linked functions per
rocker
– Using buttons to control areas (groups) or call up scenes
– Using buttons to operate wirelessly linked JUNG HOME devices
– Multi-colour status indication with optional night mode
– Feedback of load status by status LED
– Disabling local operation
– Integration of the load into areas (groups), main functions and scenes
– Up to 16 time programs control the functions of the respective system insert
(switch on, switch off, dimming, move Venetian blind, adjust temperature)
– Staircase lighting function (automatic switch-off) with switch-off warning
– Run-on time, switch-on delay, switch-off delay
– Activating/deactivating automatic functions with the JUNG HOME app
– Automatic date and time update when connecting with smartphone
– Maximum brightness and minimum brightness adjustable, with dimming insert
– Switching on with last brightness or fixed switch-on brightness, with dimming
inserts
– Ventilation position, running time, slat change-over time, change-over time for
change in direction and inverse operation adjustable, with Venetian blind insert
– Evaluation of the extension inputs (if present) to control the system insert
– Bluetooth SIG Mesh for fully encrypted wireless communication and repeater
function
– Updating via JUNG HOME App
Available by update in the future:
– Using buttons to trigger disabling function and restraint
– Time programs with sunrise and sunset (astro timer)
– Time programs with random time
– Disabling function and restraint: lock-out protection, continuously ON/OFF or
ON/OFF for fixed time
– Night light function with period for brightness reduction, with dimming insert
– Hotel function (orientation light instead of OFF), with dimming insert
– Warm dimming (changing the colour temperature with simultaneous bright-
ness increase), with DALI insert
– Wind alarm by connecting conventional weather sensors to extension input
with Venetian blind insert
You can find information on updates and dates at www.jung.de/JUNGHOME
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
5 / 26
32405203 24.02.2023
J0082405203

Behaviour after a mains voltage failure
All settings and time programs are retained. Any missed switching times are not ap-
plied later. The load output or the system insert outputs are switched off, provided the
parameter "Switching status after mains voltage returns" is set to its default setting.
If the device was not previously added to a Bluetooth Mesh network (project) by
means of the JUNG HOME app, it will switch to pairing mode for two minutes after
the mains voltage returns and the status LED will flash slowly at a regular interval in
blue.
Power failure shorter than power reserve (min. 4 hours)
– Time and date are up to date
– The following time programs are performed normally again
Power failure longer than power reserve (min. 4 hours)
– The LEDs flash in blue three times repeatedly until the time is automatically
updated when connecting with the app
– The time programs are not executed as long as the time is not up to date
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
6 / 26
32405203 24.02.2023
J0082405203

5 Operation
All settings and operations of the cover can be configured individually using the
JUNG HOME app.
Configuration in the JUNG HOME app: The default setting with the "rocker" operating
concept is described in the table.
Type of operation Brief press Long press
Switching1Switch on alternately at top,
bottom or with full surface
Switch on at top, bottom of
with full surface alternately
Dimming1Switch on at top, bottom of
with full surface to switch-
on brightness / switch off
alternately
Top: dim brighter / bottom:
dim darker
Moving Venetian blind /
shutter / awning2Stop or adjust the slats Top: move up / bottom: move down
Heating1Increase the target temper-
ature at the top by 0.5 °C /
Decrease the target tem-
perature at the top by 0.5
°C
–
Operating scenes1Call up scene at top or bot-
tom
Call up scene at top or bot-
tom
Operating an area
(group)1/2 Depending on the unit, as described for switching,
dimming, Venetian blinds
and heating
Depending on the unit, as
described for switching,
dimming, Venetian blinds
and heating
Disabling function (lock-out
protection, restraint)1– Top: activate / bottom: de- activate
Changing the colour tem-
perature (with DALI insert)
– Top: increase colour tem-
perature / bottom: decrease
colour temperature
1 Brief push-button action < 0.4 s < long push-button action
2 Brief push-button action < 1 s < long push-button action
Wireless operation
Wireless operation is done with linked JUNG HOME devices or via the JUNG HOME
App, which is also used to link the JUNG HOME devices (see 'Commissioning via
App').
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
7 / 26
32405203 24.02.2023
J0082405203

5.1 Operation via extensions
Precondition:
A push-button, an Satellite insert 2-wire with an LB Management push-button 1-gang
or an Satellite insert 3-wire, power supply with an LB Management push-button 1-
gang or LB management motion detector is connected. Multiple extensions can be
combined with each other. Operation with the Rotary satellite insert 3-wire is de-
scribed in the rotary extension instructions.
If no run-on time (load) is set, the load either switches alternately ON/OFF or specific-
ally ON at the top and OFF at the bottom, depending on the extension used.
Switching on a load for the duration of the run-on time
￭ Press the operating cover at the top or the push-button briefly or LB manage-
ment motion detector detects a movement.
The run-on time is restarted by pressing again or detecting the movement again.
If the load is supposed to be able to be switched off manually, the parameter "Manual
switch-off of run-on time" must be activated.
Setting the brightness, only in combination with dimming insert
￭ Press and hold the operating cover at the top or bottom or the push-button. In
the case of a push-button, the dimming direction is changed with each new
long actuation.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
8 / 26
32405203 24.02.2023
J0082405203

6 Mounting and electrical connection
Communication between the JUNG HOME devices and linked mobile end devices is
performed wirelessly within the range of the Bluetooth Mesh network.
The range of wireless signals can be affected by:
– Number, thickness, position of ceilings, walls and other objects
– Material type of these objects
– High-frequency interfering signals
Observe the following fitting instructions to maximise the range:
– Plan the number of JUNG HOME devices and their positions to keep the num-
ber of ceilings and walls between two devices as low as possible
– If JUNG HOME devices are installed on both sides of a solid wall, they should
be positioned as close as possible to each other on the opposite sides of the
wall. This keeps the attenuation of the wireless signal through the wall as low
as possible.
– When planning, make sure that there are as few building materials and objects
as possible that strongly attenuate the wireless signal (e.g. concrete, glass,
metal, insulated walls, water tanks, pipes, mirrors, book cabinets, storage
rooms and refrigerators) on the connection line between JUNG HOME devices
– Keep a distance of at least 1 m from devices that emit high-frequency signals
(e.g. microwave, motors) or use wireless signals at 2.4 GHz (e.g. WLAN
router, baby monitor, IP cameras, wireless loudspeakers etc.)
DANGER!
Electric shock when live parts are touched.
Electric shocks can be fatal.
Always disconnect before carrying out work on the device or load. For this, switch off
all corresponding circuit breakers, secure against being switched on again and check
that there is no voltage. Cover up adjacent live parts.
Prerequisite: The system insert (1) is mounted and connected properly (see instruc-
tions for the relevant system insert).
￭ Fit the operating cover (3) with frame on the system insert (1).
￭ Switch on mains voltage.
An system insert-cover alignment is executed.
If the status LED (4) flashes red three times at repeated intervals, the cover was pre-
viously connected to another system insert. To enable operation again, perform one
of the following steps:
￭ Fit the cover on the original system insert.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
9 / 26
32405203 24.02.2023
J0082405203

￭ With a system insert of the same type: full-surface operation of the left button
for more than 4 seconds. The parameter settings and app and network con-
nection are retained.
￭ With a system insert of a different type: reset the cover to the default setting.
The parameter settings and app and network connections are retained.
7 Commissioning via app
Prerequisite: The JUNG HOME device does not yet belong to a Bluetooth Mesh net-
work. Otherwise reset the device to the default setting.
If a Bluetooth Mesh network (project) does not yet exist, a new project must first be
created for the first JUNG HOME device in the JUNG HOME app.
If a Bluetooth Mesh network already exists, the project file for this network must be
opened in order to pair the new device.
After switching on the mains voltage, the device is automatically in pairing
mode for two minutes.
Image3: Commissioning
￭ Activate pairing mode manually:
Press the left button over entire surface for longer than 4 seconds.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
10 / 26
32405203 24.02.2023
J0082405203

The status LED flashes blue slowly. Pairing mode is active for two minutes.
￭ Start the JUNG HOME app.
The app shows all devices in pairing mode.
￭ Select a device in the app.
To identify the selected device, its status LED flashes more quickly in blue.
￭ Add the device to the project.
The status LED lights up blue for 5 seconds to acknowledge successful pair-
ing.
If the status LED flashes red very fast, pairing has failed and needs to be re-
tried.
The JUNG HOME app can then be used to link devices wirelessly and config-
ure the parameters and operation (see list of functions and parameters).
Once the commissioning of the JUNG HOME project has been completed,
hand over the project file to the owner.
Besides basic commissioning, the JUNG HOME app enables device updates and
convenient operation of further individual configuration options:
– Link: A button, binary input or motion sensor can be controlled by linking it to a
load (e.g. dimmer, socket, relay, shutter etc.). Several loads can be controlled
together by linking them to an area or scene.
– Area: Different loads (e.g. dimmer, socket, relay, shutter etc.) can be grouped
in an area to allow them to be controlled together.
– Scene: Different loads (e.g. dimmer, socket, relay, shutter etc.) can be
grouped in a scene so that, by calling up a scene, each load assumes the load
status stored in the scene.
– Automatic function: An automatic function can be used to control the locally
connected load (no wireless link) by means of time programs. Depending on
the device type, there are further automatic functions in JUNG HOME, such as
hotel function, night light function, holiday program or switching thresholds.
8 Resetting the device to the factory setting
If local operation is disabled with the "operating lock" parameter, the default
setting can be reset to only within two minutes after switching on the mains
voltage.
If the device has already been added to a project with the JUNG HOME app, it
can be reset also to the default setting in one step with the "Delete device"
function from the app.
If the device cannot be reset to the default settings with the app or the app is not at
hand, the device can be reset as follows:
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
11 / 26
32405203 24.02.2023
J0082405203

Image4: Factory reset
￭ Press the left button over its entire surface for longer than 20 seconds until the
status LED quickly flashes red.
￭ Release the button and press it briefly once again within 10 seconds.
The status LED flashes red more slowly for approx. 5 seconds, the device has
been reset to the default setting.
After resetting the device to the default setting, it must be removed from the JUNG
HOME app provided it has not already been deleted from the app.
9 Technical data
Ambient temperature -5 ... +45 °C
Transport temperature -25 ... +70 °C
Storage temperature -5 ... +45 °C
Relative humidity 20 ... 70 % (no moisture
condensation)
Accuracy per month ± 13 s
Power reserve min. 4 h
The time is updated with every connection to the app
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
12 / 26
32405203 24.02.2023
J0082405203

Radio frequency 2.402 ... 2.480 GHz
Transmission capacity max. 10 mW, Class 1.5
Transmission range (inside building) typ. 30 m
This device includes an integrated battery. At the end of its useful life, dispose
of the device together with the battery in accordance with the environmental
regulations. Do not throw device into household waste. Consult your local authorities
about environmentally friendly disposal. According to statutory provisions, the end
consumer is obligated to return the device.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
13 / 26
32405203 24.02.2023
J0082405203

10 List of functions and parameters
The JUNG HOME app can be used to configure all functions of the JUNG HOME
device and its behaviour in the Bluetooth Mesh project for the respective individual
purposes.
One or more devices are created in the app when commissioning with the app, de-
pending on the system insert used:
– A device that maps the operating cover and includes its functions and para-
meters.
– A device that maps the system insert used and its load control with all the cor-
responding functions and parameters. With a two-channel system insert, two
devices are used.
All devices created in the JUNG HOME app can be used independently and set sep-
arately.
JUNG HOME push-button settings (cover) ǎ
Parameters Setting options,
Default setting
Explanations
Operating
concept
Rocker, button
Default setting: rocker
Rocker: The operation of the button at the
top or button applies to the same load,
same area or same disabling function.
Operation at the top or bottom usually
leads to directly opposite reactions. (E.g.
light ON/OFF, brighter/darker, move up/
down)
Button: Operation of the button at the top
or bottom applies to different loads, areas
or scenes. When controlling loads or
areas, renewed operation of the same
pressure point will lead to opposite reac-
tions (e.g. light ON/OFF, brighter/darker,
up/stop/down).
Behaviour of the
status LED
when switched
on, moving or
as orientation
LED
Colour selection
Default setting: green
(orange for button oper-
ating concept)
LED colour and brightness** when a load
is switched on, a Venetian blind / shutter /
awning is moving or the LED in the button
operating concept is used as orientation
LED.
Behaviour of the
status LED
when switched
off or stationary
Colour selection
Default setting: orange
LED colour and brightness** when a load
is switched off or a Venetian blind / shut-
ter / awning is stationary.
Night mode** Off, on
Default setting: off
In night mode, the status LED is lit up
only for max. 5 seconds, not permanently,
after pressing the button.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
14 / 26
32405203 24.02.2023
J0082405203

Parameters Setting options,
Default setting
Explanations
Operating lock** No lock, factory reset
block, operating block
Default setting: no lock
Factory reset block: prevents resetting on
the device and hence the removal from a
project and pairing again by unauthorised
persons. After the mains voltage returns,
the factory reset lock is deactivated for
two minutes.
Operating block: prevents normal opera-
tion on the device and hence the load
from being controlled. This block can be
used, for example, to restrict manual ac-
cess temporarily.
Operation by means of the app is still
possible. The operating lock cannot be
deactivated on the device.
** Available by update in the future: You can find notes on updates and dates at
www.jung.de/JUNGHOME
Load control settings (system insert)
Settings for automatic functions ǐ
Parameters Setting options,
Default setting
Explanations
Time programs Load status, time and
weekdays
The load status can be changed at
defined times (weekdays and time) de-
pending on the system insert.
Astro timer** Off, sunrise or sunset
Default setting: off
The astro timer shows the sunrise and
sunset times in the course of a calendar
year. Depending on the location, load
statuses can be changed with the position
of the sun, for example to switch on the
outdoor lighting at sunset and switch it off
again at sunrise.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
15 / 26
32405203 24.02.2023
J0082405203

Parameters Setting options,
Default setting
Explanations
Astro timer**
time shift
0 (off) ... 120 minutes
before or after sunrise
and sunset
Default setting: off
Astro times represent the sunrise and
sunset times in the course of a calendar
year.
If you want the time program to be ex-
ecuted in the early morning before the
start of twilight or only at full brightness,
this can be implemented with the "sun-
rise" shift.
If you want the time program to be ex-
ecuted in the evening at the start of twi-
light or only at full darkness, this can be
implemented with the "sunset" shift. Dis-
places the load actuation time by the set
value.
Astro timer**
limit range
Off, earliest time, latest
time default setting: off
To narrow the time range of an astro
timer down to an earliest and/or latest ex-
ecution time.
For example, the garden lighting can be
switched off at the latest at 9:00pm even
if the sun does not set until 10:00pm.
Set location** Geographic location The astro timer in the JUNG HOME
devices needs the geographic location of
the project to calculate the sunrise or sun-
set time. The astro timer is calculated
once a week for the localised place.
** Available by update in the future: You can find notes on updates and dates at
www.jung.de/JUNGHOME
Automatic functions for load output 2 with multi-channel devices will be available by
update in the future (notes on updates at www.jung.de/JUNGHOME).
Additional settings for switch inserts Lj
Parameters Setting options,
Default setting
Explanations
Switch-on delay 0 s (off) ... 240 min
Default setting: off
Switches on the load after a switch-on
command, delayed by the value. Re-
peated switch-on commands during the
current delay do not start the delay again.
If the load has not yet been switched on
due to the delay, the load remains
switched off when a switch-off command
arrives.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
16 / 26
32405203 24.02.2023
J0082405203

Parameters Setting options,
Default setting
Explanations
Switch-off delay 0 s (off) ... 240 min
Default setting: off
Switches off the load after a switch-off
command, delayed by the value. Re-
peated switch-off commands during the
current delay restart the delay time. If the
load has not yet been switched off due to
the delay when a switch-on command
comes, then the load will remain on.
Switch-off warn-
ing
Off, on
Default setting: off
If the switch-off warning is switched on,
the light is not switched off immediately
after the run-on time (load) has elapsed.
Triple flashing at an interval of
10 seconds shows that the light will be
switched off soon. The run-on time is
thereby prolonged by approx.
30 seconds. If a movement is detected by
a linked JUNG HOME sensor cover or the
load switched on again by operating an
extension or by a linked JUNG HOME op-
erating cover during the switch-off warn-
ing, the run-on time is restarted and the
light remains on.
Run-on time
(load)
0 s (off) ... 240 min
Default setting: off
Ensures that the load is switched off after
the set run-on time expires instead of re-
maining permanently switched on after a
switch-on command.
If a movement is detected by a linked
JUNG HOME sensor cover during the
run-on time or the operating cover is
switched on again by operating an exten-
sion or a linked JUNG HOME operating
cover, the run-on time is restarted and the
light remains on.
The load can be switched off early during
the current run-on time only if the "Manual
switch-off during run-on time" parameter
is set to "On" or a disabling function (con-
tinuously off) is started.
Manual switch-
off during run-
on time
Off, on
Default setting: on
If this parameter is set to "On", it will be
possible to switch off the load manually
during the current run-on time (load).
For automatic staircase lighting controlled
by JUNG HOME operating and/or sensor
covers, this parameter should be set to
"Off" to prevent the light from being
switched off by a second person.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
17 / 26
32405203 24.02.2023
J0082405203

Parameters Setting options,
Default setting
Explanations
Presentation
function
Off, on
Default setting: off
The presentation function is used in com-
bination with a linked JUNG HOME pres-
ence detector. The presentation function
can be switched on or off with the app or
a linked JUNG HOME push-button.
With the presentation function switched
on, the light is switched off and move-
ments detected by a JUNG HOME pres-
ence detector are prevented from switch-
ing on the light for a defined locking time.
Not only sensor signals from JUNG
HOME presence detectors, but also
sensor signals from JUNG HOME motion
detectors, switch-on and switch-off com-
mands via extensions, wireless control
with the app and other JUNG HOME
devices restart the locking time.
The presentation function is automatically
ended at the end of the locking time. Al-
ternatively, the presentation function can
be switched off manually.
Locking time
presentation
function
3 ... 240 min
Default setting: 3 min
Defines the locking time during which the
light remains off with the "presentation
function" switched on.
Sensor signals from JUNG HOME pres-
ence detectors and JUNG HOME motion
detectors, switch-on and switch-off com-
mands via extensions, wireless control
with the app and other JUNG HOME
devices restart the locking time.
Minimum
switching repeat
time**
100 ms ... 10 s
Default setting: 100 ms
Limits the switching speed of the device
by increasing the value, in order to pro-
tect the connected load, for example.
Only when the set time has elapsed is
switching possible again. The last com-
mand during the blocking time is ex-
ecuted after a delay. The switching repeat
time starts after each switching operation.
Behaviour after
mains voltage
returns
Switched off, switched
on, previous status
Default setting: off
Behaviour of the load output after the
mains voltage returns.
Note: Do not use the "switched on" set-
ting in combination with consumers that
could lead to danger to life or limb or
damage to property.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
18 / 26
32405203 24.02.2023
J0082405203

Parameters Setting options,
Default setting
Explanations
Disabling func-
tion (restraint
guidance)**
Deactivated, continu-
ously ON, continuously
OFF, for fixed time ON/
OFF
Default setting: deactiv-
ated
The disabling function switches the load
output to the desired status and blocks it
against control by the motion sensor, ex-
tension operation, time programs and
wireless control with the app and other
JUNG HOME devices. The lock applies
for an adjustable time or until the dis-
abling function is deactivated again
** Available by update in the future: You can find notes on updates and dates at
www.jung.de/JUNGHOME
Additional settings for dimming/DALI inserts Lj
Parameters Setting options,
Default setting
Explanations
Switch-on delay 0 s (off) ... 240 min
Default setting: off
Switches on the load after a switch-on
command, delayed by the value. Re-
peated switch-on commands during the
current delay do not start the delay again.
If the load has not yet been switched on
due to the delay, the load remains
switched off when a switch-off command
arrives.
Switch-off delay 0 s (off) ... 240 min
Default setting: off
Switches off the load after a switch-off
command, delayed by the value. Re-
peated switch-off commands during the
current delay restart the delay time. If the
load has not yet been switched off due to
the delay when a switch-on command
comes, then the load will remain on.
Switch-off warn-
ing
Off, on
Default setting: off
If the switch-off warning is switched on,
the light is not switched off immediately
after the run-on time (load) has elapsed.
The light is first dimmed to minimum
brightness within 30 seconds. The run-on
time is thereby prolonged by approx.
30 seconds. If, during the switch-off warn-
ing, a movement is detected by a linked
JUNG HOME sensor cover or the warning
is switched on again by operating an ex-
tension or by a linked JUNG HOME oper-
ating cover, the run-on time will be restar-
ted and the light switched back to the
switch-on brightness.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
19 / 26
32405203 24.02.2023
J0082405203

Parameters Setting options,
Default setting
Explanations
Run-on time
(load)
0 s (off) ... 240 min
Default setting: off
Ensures that the load is switched off after
the set run-on time expires instead of re-
maining permanently switched on after a
switch-on command.
If a movement is detected by a linked
JUNG HOME sensor cover during the
run-on time or the operating cover is
switched on again by operating an exten-
sion or a linked JUNG HOME operating
cover, the run-on time is restarted and the
light remains on.
The load can be switched off early during
the current run-on time only if the "Manual
switch-off during run-on time" parameter
is set to "On" or a disabling function (con-
tinuously off) is started.
Manual switch-
off during run-
on time
Off, on
Default setting: on
If this parameter is set to "On", it will be
possible to switch off the load manually
during the current run-on time (load).
For automatic staircase lighting controlled
by JUNG HOME operating and/or sensor
covers, this parameter should be set to
off to prevent the light from being able to
be switched off by a second person.
JUNG HOME push-button 1-gang, JUNG HOME push-button 2-gang
20 / 26
32405203 24.02.2023
J0082405203