Jungheinrich ECE 320 User manual

Operating Instructions
51076425
G
03.08-
07.08
ECE 320

0108.GB
Foreword
The present ORIGINAL OPERATING INSTRUCTIONS are designed to provide
sufficient instruction for the safe operation of the industrial truck. The information is
provided clearly and concisely. The chapters are arranged by letter. Each chapter
starts with page 1. The page identification consists of a chapter letter and a page
number.
For example: Page B 2 is the second page in chapter B.
The operating instructions detail different truck models. When operating and servicing
the truck, make sure that the instructions apply to your truck model.
Safety instructions and important explanations are indicated by the following
graphics:
FUsed before safety instructions which must be observed to avoid danger to
personnel.
MUsed before notices which must be observed to avoid material damage.
ZUsed before notices and explanations.
tUsed to indicate standard equipment.
oUsed to indicate optional equipment.
Our trucks are subject to ongoing development. Jungheinrich reserves the right to
alter the design, equipment and technical features of the truck. No guarantee of
particular features of the truck should therefore be inferred from the present operating
instructions.
Copyright
Copyright of these operating instructions remains with JUNGHEINRICH AG.
Jungheinrich Aktiengesellschaft
Am Stadtrand 35
22047 Hamburg - GERMANY
Telephone: [phone]
www.jungheinrich.com
0108.GB
Foreword
The present ORIGINAL OPERATING INSTRUCTIONS are designed to provide
sufficient instruction for the safe operation of the industrial truck. The information is
provided clearly and concisely. The chapters are arranged by letter. Each chapter
starts with page 1. The page identification consists of a chapter letter and a page
number.
For example: Page B 2 is the second page in chapter B.
The operating instructions detail different truck models. When operating and servicing
the truck, make sure that the instructions apply to your truck model.
Safety instructions and important explanations are indicated by the following
graphics:
FUsed before safety instructions which must be observed to avoid danger to
personnel.
MUsed before notices which must be observed to avoid material damage.
ZUsed before notices and explanations.
tUsed to indicate standard equipment.
oUsed to indicate optional equipment.
Our trucks are subject to ongoing development. Jungheinrich reserves the right to
alter the design, equipment and technical features of the truck. No guarantee of
particular features of the truck should therefore be inferred from the present operating
instructions.
Copyright
Copyright of these operating instructions remains with JUNGHEINRICH AG.
Jungheinrich Aktiengesellschaft
Am Stadtrand 35
22047 Hamburg - GERMANY
Telephone: [phone]
www.jungheinrich.com

0108.GB
0108.GB

I 1
0708.GB
Index
A Correct Application
B Truck Description
1 Application ........................................................................................... B 1
2 Assemblies .......................................................................................... B 2
3 Standard Version Specifications ......................................................... B 3
3.1 Performance Data ............................................................................... B 3
3.2 Dimensions ......................................................................................... B 4
3.3 EN norms ............................................................................................ B 5
3.4 Conditions of use ................................................................................ B 5
4 Identification points and data plates .................................................... B 6
4.1 Truck data plate .................................................................................. B 7
C Transport and Commissioning
1 Lifting by crane .................................................................................... C 1
2 Securing the truck during transport ..................................................... C 2
3 Using the truck for the first time .......................................................... C 3
4 Operating the truck without its own drive system ................................ C 4
D Battery Maintenance, Charging & Replacement
1 Safety regulations for handling acid batteries ..................................... D 1
2 Battery types ....................................................................................... D 2
3 Exposing the battery ........................................................................... D 2
4 Charging the battery ............................................................................ D 3
5 Battery removal and installation .......................................................... D 4
E Operation
1 Safety Regulations for the Operation of Forklift Trucks ...................... E 1
2 Controls and Displays ......................................................................... E 2
3 Starting up the truck ............................................................................ E 6
4 Industrial Truck Operation ................................................................... E 7
4.1 Safety regulations for truck operation ................................................. E 7
4.2 Travel, steering, braking ...................................................................... E 8
4.3 Pedestrian operation (o) .................................................................... E 12
4.4 Lifting and depositing loads ................................................................. E 14
4.5 Parking the truck securely ................................................................... E 15
5 Keypad (CANCODE) (o) .................................................................... E 16
5.1 Code Lock ........................................................................................... E 16
5.2 Travel programs .................................................................................. E 18
5.3 Parameters .......................................................................................... E 18
5.4 Parameter Settings ............................................................................. E 19
I 1
0708.GB
Index
A Correct Application
B Truck Description
1 Application ........................................................................................... B 1
2 Assemblies .......................................................................................... B 2
3 Standard Version Specifications ......................................................... B 3
3.1 Performance Data ............................................................................... B 3
3.2 Dimensions ......................................................................................... B 4
3.3 EN norms ............................................................................................ B 5
3.4 Conditions of use ................................................................................ B 5
4 Identification points and data plates .................................................... B 6
4.1 Truck data plate .................................................................................. B 7
C Transport and Commissioning
1 Lifting by crane .................................................................................... C 1
2 Securing the truck during transport ..................................................... C 2
3 Using the truck for the first time .......................................................... C 3
4 Operating the truck without its own drive system ................................ C 4
D Battery Maintenance, Charging & Replacement
1 Safety regulations for handling acid batteries ..................................... D 1
2 Battery types ....................................................................................... D 2
3 Exposing the battery ........................................................................... D 2
4 Charging the battery ............................................................................ D 3
5 Battery removal and installation .......................................................... D 4
E Operation
1 Safety Regulations for the Operation of Forklift Trucks ...................... E 1
2 Controls and Displays ......................................................................... E 2
3 Starting up the truck ............................................................................ E 6
4 Industrial Truck Operation ................................................................... E 7
4.1 Safety regulations for truck operation ................................................. E 7
4.2 Travel, steering, braking ...................................................................... E 8
4.3 Pedestrian operation (o) .................................................................... E 12
4.4 Lifting and depositing loads ................................................................. E 14
4.5 Parking the truck securely ................................................................... E 15
5 Keypad (CANCODE) (o) .................................................................... E 16
5.1 Code Lock ........................................................................................... E 16
5.2 Travel programs .................................................................................. E 18
5.3 Parameters .......................................................................................... E 18
5.4 Parameter Settings ............................................................................. E 19

0708.GB
I 2
5.5 Travel parameters ............................................................................... E 23
6ISM(o) ............................................................................................... E 27
7 Battery discharge indicator .................................................................. E 28
7.1 Battery Discharge Indicator (t) .......................................................... E 28
8 Display instrument (CANDIS) (o) ....................................................... E 29
8.1 Operating hours display ...................................................................... E 30
8.2 Power up test ...................................................................................... E 30
9 Troubleshooting .................................................................................. E 31
F Industrial Truck Maintenance
1 Operational Safety and Environmental Protection .............................. F 1
2 Maintenance Safety Regulations ........................................................ F 1
3 Servicing and Inspection ..................................................................... F 3
4 Maintenance checklist ......................................................................... F 4
5 Lubrication Schedule ........................................................................... F 6
5.1 Consumables ...................................................................................... F 7
6 Maintenance Instructions .................................................................... F 8
6.1 Preparing the truck for maintenance and repairs ................................ F 8
6.2 Tightening the wheel nuts ................................................................... F 8
6.3 Remove the front panel ....................................................................... F 9
6.4 Checking electrical fuses .................................................................... F 10
6.5 Recommissioning ................................................................................ F 11
7 Decommissioning the industrial truck .................................................. F 11
7.1 Prior to decommissioning: ................................................................... F 11
7.2 During decommissioning: .................................................................... F 11
7.3 Returning the truck to operation after decommissioning ..................... F 12
8 Safety checks to be performed at regular intervals and following
any unusual incidents .......................................................................... F 12
9 Final de-commissioning, disposal ....................................................... F 12
0708.GB
I 2
5.5 Travel parameters ............................................................................... E 23
6ISM(o) ............................................................................................... E 27
7 Battery discharge indicator .................................................................. E 28
7.1 Battery Discharge Indicator (t) .......................................................... E 28
8 Display instrument (CANDIS) (o) ....................................................... E 29
8.1 Operating hours display ...................................................................... E 30
8.2 Power up test ...................................................................................... E 30
9 Troubleshooting .................................................................................. E 31
F Industrial Truck Maintenance
1 Operational Safety and Environmental Protection .............................. F 1
2 Maintenance Safety Regulations ........................................................ F 1
3 Servicing and Inspection ..................................................................... F 3
4 Maintenance checklist ......................................................................... F 4
5 Lubrication Schedule ........................................................................... F 6
5.1 Consumables ...................................................................................... F 7
6 Maintenance Instructions .................................................................... F 8
6.1 Preparing the truck for maintenance and repairs ................................ F 8
6.2 Tightening the wheel nuts ................................................................... F 8
6.3 Remove the front panel ....................................................................... F 9
6.4 Checking electrical fuses .................................................................... F 10
6.5 Recommissioning ................................................................................ F 11
7 Decommissioning the industrial truck .................................................. F 11
7.1 Prior to decommissioning: ................................................................... F 11
7.2 During decommissioning: .................................................................... F 11
7.3 Returning the truck to operation after decommissioning ..................... F 12
8 Safety checks to be performed at regular intervals and following
any unusual incidents .......................................................................... F 12
9 Final de-commissioning, disposal ....................................................... F 12

1
0506.GB
Appendix
JH Traction Battery Operating Instructions
ZThese operating instructions apply only to Jungheinrich battery models. If using
another brand, refer to the manufacturer's operating instructions.
1
0506.GB
Appendix
JH Traction Battery Operating Instructions
ZThese operating instructions apply only to Jungheinrich battery models. If using
another brand, refer to the manufacturer's operating instructions.

0506.GB
2
0506.GB
2

A 1
1206.GB
A Correct Application
ZThe “Guidelines for the Correct Use and Application of Industrial Trucks” (VDMA) are
supplied with the truck. The guidelines form part of these operating instructions and
must be observed. National regulations apply in full.
The truck described in the present operating instructions is an industrial truck
designed for lifting and transporting loads.
It must be applied, operated and serviced in accordance with the instructions
contained in the present manual. All other types of use lie beyond the scope of
application and can result in damage to personnel, the truck or property. In particular,
avoid overloading the truck with loads which are too heavy or placed on one side. The
data plate attached to the truck or the load chart are binding for the maximum load
capacity. The industrial truck must not be used in fire or explosion endangered areas,
or areas threatened by corrosion or excessive dust.
Proprietor responsibilities: For the purposes of the present operator manual the
“proprietor” is defined as any natural or legal person who either uses the industrial
truck himself, or on whose behalf it is used. In special cases (e.g. leasing or renting)
the proprietor is considered to be the person who, in accordance with existing
contractual agreements between the owner and user of the industrial truck, is
charged with operational duties.
The proprietor must ensure that the industrial truck is used only for the purpose it is
intended for and that danger to life and limb of the user and third parties are excluded.
Furthermore, accident prevention regulations, safety regulations and operating,
servicing and repair guidelines must be followed. The owner must ensure that all
truck users have read and understood these operating instructions.
MFailure to comply with the operating instructions shall invalidate the warranty. The
same applies if improper work is carried out on the truck by the customer or third
parties without the permission of the manufacturer’s customer service department.
Attaching accessories: The mounting or installation of additional equipment which
affects or enhances the performance of the industrial truck requires the written
permission of the manufacturer. In some cases, local authority approval shall be
required.
Approval of the local authorities however does not constitute the manufacturer’s
approval.
A 1
1206.GB
A Correct Application
ZThe “Guidelines for the Correct Use and Application of Industrial Trucks” (VDMA) are
supplied with the truck. The guidelines form part of these operating instructions and
must be observed. National regulations apply in full.
The truck described in the present operating instructions is an industrial truck
designed for lifting and transporting loads.
It must be applied, operated and serviced in accordance with the instructions
contained in the present manual. All other types of use lie beyond the scope of
application and can result in damage to personnel, the truck or property. In particular,
avoid overloading the truck with loads which are too heavy or placed on one side. The
data plate attached to the truck or the load chart are binding for the maximum load
capacity. The industrial truck must not be used in fire or explosion endangered areas,
or areas threatened by corrosion or excessive dust.
Proprietor responsibilities: For the purposes of the present operator manual the
“proprietor” is defined as any natural or legal person who either uses the industrial
truck himself, or on whose behalf it is used. In special cases (e.g. leasing or renting)
the proprietor is considered to be the person who, in accordance with existing
contractual agreements between the owner and user of the industrial truck, is
charged with operational duties.
The proprietor must ensure that the industrial truck is used only for the purpose it is
intended for and that danger to life and limb of the user and third parties are excluded.
Furthermore, accident prevention regulations, safety regulations and operating,
servicing and repair guidelines must be followed. The owner must ensure that all
truck users have read and understood these operating instructions.
MFailure to comply with the operating instructions shall invalidate the warranty. The
same applies if improper work is carried out on the truck by the customer or third
parties without the permission of the manufacturer’s customer service department.
Attaching accessories: The mounting or installation of additional equipment which
affects or enhances the performance of the industrial truck requires the written
permission of the manufacturer. In some cases, local authority approval shall be
required.
Approval of the local authorities however does not constitute the manufacturer’s
approval.

B 1
0708.GB
B Truck Description
1 Application
The ECE 220/225 is a four-wheel electric pallet truck with an operator position,
equipped either with a Jet Pilot or electric tiller steering (o). The truck is designed to
transport and pick goods on level surfaces. Roll cages and open bottom pallets or
pallets with transverse boards (provided these are outside the range of the load
wheels) can be collected.
The rated capacity can be found on the data pate or the capacity data plate Qmax.
B 1
0708.GB
B Truck Description
1 Application
The ECE 220/225 is a four-wheel electric pallet truck with an operator position,
equipped either with a Jet Pilot or electric tiller steering (o). The truck is designed to
transport and pick goods on level surfaces. Roll cages and open bottom pallets or
pallets with transverse boards (provided these are outside the range of the load
wheels) can be collected.
The rated capacity can be found on the data pate or the capacity data plate Qmax.

0708.GB
B 2
2 Assemblies
Item Model Item Model
1tFront panel 11 o“Lift” button
2tBattery panel 12 o“Lower” button
3tJet Pilot 13 oReverse “pedestrian
operation” button
4tMain switch / isolator
(emergency disconnect)
14 tForward “pedestrian
operation” button
5tController 15 tOperator platform
6tBrake button 16 tLift mechanism
7oKeypad
(CANCODE)
17 tTiller
8oDisplay instrument
(CANDIS)
18 oCastor wheel
9tKey switch 19 tDrive wheel
10 oStop button
t= Standard equipment o = Optional Equipment
6
5
1
2
3
78 9
4
15
16
17
18
19
14
10
13
11
12
0708.GB
B 2
2 Assemblies
Item Model Item Model
1tFront panel 11 o“Lift” button
2tBattery panel 12 o“Lower” button
3tJet Pilot 13 oReverse “pedestrian
operation” button
4tMain switch / isolator
(emergency disconnect)
14 tForward “pedestrian
operation” button
5tController 15 tOperator platform
6tBrake button 16 tLift mechanism
7oKeypad
(CANCODE)
17 tTiller
8oDisplay instrument
(CANDIS)
18 oCastor wheel
9tKey switch 19 tDrive wheel
10 oStop button
t= Standard equipment o = Optional Equipment
6
5
1
2
3
78 9
4
15
16
17
18
19
14
10
13
11
12

B 3
0708.GB
3 Standard Version Specifications
ZTechnical specification details in accordance with VDI 2198.
Technical modifications and additions reserved.
3.1 Performance Data
*) For trucks with longer forks the load centre is in the centre of the fork.
Model ECE 320
Q Rated capacity 2000 kg
cLoad centre distance with
standard fork length *)1200 mm
Travel speed
w / w.o. rated load 9.5 / 12.5 km/h
Lift speed
with / without rated load 0.08 / 0.11 m/s
Lower speed
with / without rated load 0.12 / 0.05 m/s
h
132
h1
b
y
e
95
c
L
h3
b1
L2
a/2a/2
h13
30
218
(L1)
L6
b3b11 b5
Wa
253388 408
B 3
0708.GB
3 Standard Version Specifications
ZTechnical specification details in accordance with VDI 2198.
Technical modifications and additions reserved.
3.1 Performance Data
*) For trucks with longer forks the load centre is in the centre of the fork.
Model ECE 320
Q Rated capacity 2000 kg
cLoad centre distance with
standard fork length *)1200 mm
Travel speed
w / w.o. rated load 9.5 / 12.5 km/h
Lift speed
with / without rated load 0.08 / 0.11 m/s
Lower speed
with / without rated load 0.12 / 0.05 m/s
h
132
h1
b
y
e
95
c
L
h3
b1
L2
a/2a/2
h13
30
218
(L1)
L6
b3b11 b5
Wa
253388 408

0708.GB
B 4
3.2 Dimensions
(all dimensions in mm)
Model ECE 320
l1Overall length 3750
l2Headlength 1350
h13 Lowered fork height 90
h3Rated lift 700
h1Mast height retracted 1505
hbBattery panel height 959
hfOperator platform height 132
b1Truck width 810
lTrack Width 2400
b3Inside spread 180
b11 Fork length 375
b5Width across forks 570
e Fork width 195
Ast Working aisle width, pallets 1000x1200 traverse 4113
Ast Working aisle width, pallets 800x1200 length 4113
aSafety distance 200
Wa Turning radius 3130
Net weight: See truck data plate
0708.GB
B 4
3.2 Dimensions
(all dimensions in mm)
Model ECE 320
l1Overall length 3750
l2Headlength 1350
h13 Lowered fork height 90
h3Rated lift 700
h1Mast height retracted 1505
hbBattery panel height 959
hfOperator platform height 132
b1Truck width 810
lTrack Width 2400
b3Inside spread 180
b11 Fork length 375
b5Width across forks 570
e Fork width 195
Ast Working aisle width, pallets 1000x1200 traverse 4113
Ast Working aisle width, pallets 800x1200 length 4113
aSafety distance 200
Wa Turning radius 3130
Net weight: See truck data plate

B 5
0708.GB
3.3 EN norms
Noise level: 61 dB(A)
in accordance with EN 12053 as harmonized with
ISO 4871.
ZThe noise emission level is calculated in accordance with standard procedures and
takes into account the noise level when travelling, lifting and when idle. The noise
level is measured at the driver’s ear.
Vibration: 0.85 m/s²
in accordance with EN 13059
ZThe vibration acceleration acting on the body in the operating position is, in
accordance with standard procedures, the linearly integrated, weighted acceleration
in the vertical direction. It is calculated when travelling over bumps at constant speed.
Electromagnetic Compatibility (
The manufacturer confirms that equipment complies with
tolerance levels for electromagnetic emissions and
resistance as well as static electricity discharge testing in
accordance with EN 12895 including the normative
procedures contained therein.
ZNo changes to electric or electronic components or their arrangement may be made
without the written agreement of the manufacturer.
3.4 Conditions of use
Ambient temperature
- during operation -10°C to 40 °C
ZSpecial equipment and authorisation are required if the truck is to be constantly used
in conditions of extreme temperature or air humidity fluctuations.
B 5
0708.GB
3.3 EN norms
Noise level: 61 dB(A)
in accordance with EN 12053 as harmonized with
ISO 4871.
ZThe noise emission level is calculated in accordance with standard procedures and
takes into account the noise level when travelling, lifting and when idle. The noise
level is measured at the driver’s ear.
Vibration: 0.85 m/s²
in accordance with EN 13059
ZThe vibration acceleration acting on the body in the operating position is, in
accordance with standard procedures, the linearly integrated, weighted acceleration
in the vertical direction. It is calculated when travelling over bumps at constant speed.
Electromagnetic Compatibility (
The manufacturer confirms that equipment complies with
tolerance levels for electromagnetic emissions and
resistance as well as static electricity discharge testing in
accordance with EN 12895 including the normative
procedures contained therein.
ZNo changes to electric or electronic components or their arrangement may be made
without the written agreement of the manufacturer.
3.4 Conditions of use
Ambient temperature
- during operation -10°C to 40 °C
ZSpecial equipment and authorisation are required if the truck is to be constantly used
in conditions of extreme temperature or air humidity fluctuations.

0708.GB
B 6
4 Identification points and data plates
ZThe capacity plate (26) indicates the maximum capacity of the truck, Qmax. The rated
capacity as shown must not be exceeded. The plate stipulates that the load on the
fork should be spread as evenly as possible.
Item Model
20 “Attention Touch Mode” warning decal
*) for “Touch mode only in drive direction” option
21 Test sticker (o)
22 Truck data plate
23 Warning: “Do not reach into the mast”
24 Serial number, on the left or right of the mast section
25 Attachment point of crane loading (inside), hook symbol enhanced
26 Capacity Qmax
21
26
25
22
23
24
Qmax 2000 kg
*)
20
20
*)
20
20
0708.GB
B 6
4 Identification points and data plates
ZThe capacity plate (26) indicates the maximum capacity of the truck, Qmax. The rated
capacity as shown must not be exceeded. The plate stipulates that the load on the
fork should be spread as evenly as possible.
Item Model
20 “Attention Touch Mode” warning decal
*) for “Touch mode only in drive direction” option
21 Test sticker (o)
22 Truck data plate
23 Warning: “Do not reach into the mast”
24 Serial number, on the left or right of the mast section
25 Attachment point of crane loading (inside), hook symbol enhanced
26 Capacity Qmax
21
26
25
22
23
24
Qmax 2000 kg
*)
20
20
*)
20
20

B 7
0708.GB
4.1 Truck data plate
ZFor queries relating to the truck or spare part orders, please state the truck’s serial
no. (28).
Item Model Item Model
27 Type 33 Manufacturer
28 Serial no. 34 Min./max. battery weight (kg)
29 Rated capacity (kg) 35 Output (kW)
30 Battery: Voltage (V) 36 Load centre of gravity (mm)
31 Net weight w.o. battery (kg) 37 Year of Manufacture
32 Manufacturer’s logo 38 Option
33
32
34
31
35
30
36
29
37
28
38
27
B 7
0708.GB
4.1 Truck data plate
ZFor queries relating to the truck or spare part orders, please state the truck’s serial
no. (28).
Item Model Item Model
27 Type 33 Manufacturer
28 Serial no. 34 Min./max. battery weight (kg)
29 Rated capacity (kg) 35 Output (kW)
30 Battery: Voltage (V) 36 Load centre of gravity (mm)
31 Net weight w.o. battery (kg) 37 Year of Manufacture
32 Manufacturer’s logo 38 Option
33
32
34
31
35
30
36
29
37
28
38
27

0708.GB
B 8
0708.GB
B 8

C 1
04.08.GB
C Transport and Commissioning
1 Lifting by crane
FOnly use lifting gear with
sufficient capacity
(for transport weight see truck
data plate).
ZLifting gear attachment points
are provided on the chassis (1)
and the fork (2) in case the truck
is to be lifted or transported by
crane.
– Park the truck securely (see
Chapter E).
– Open the front panel and put it
to one side (see chapter F).
– Secure the lifting gear to the
attachment points (1) and (2).
MThe lifting gear must be
attached to the attachment
points in such a manner that it
cannot slip under any
circumstances and cannot come into contact with any attachments of the truck when
the truck is lifted.
2
1
C 1
04.08.GB
C Transport and Commissioning
1 Lifting by crane
FOnly use lifting gear with
sufficient capacity
(for transport weight see truck
data plate).
ZLifting gear attachment points
are provided on the chassis (1)
and the fork (2) in case the truck
is to be lifted or transported by
crane.
– Park the truck securely (see
Chapter E).
– Open the front panel and put it
to one side (see chapter F).
– Secure the lifting gear to the
attachment points (1) and (2).
MThe lifting gear must be
attached to the attachment
points in such a manner that it
cannot slip under any
circumstances and cannot come into contact with any attachments of the truck when
the truck is lifted.
2
1

04.08.GB
C 2
2 Securing the truck during transport
FThe truck must be securely fastened when transported on a lorry or a trailer. The lorry
/ trailer must have fastening rings.
– To secure the truck attach the tensioning belt to the strap points (1) and secure
them to the fastening rings.
– Tighten the tensioning belt with the tensioner.
MLoading must be carried out by specially trained staff in accordance with
recommendations contained in Guidelines VDI 2700 and VDI 2703. In each case
correct measurements shall be determined and appropriate safety measures
adopted.
1
1
04.08.GB
C 2
2 Securing the truck during transport
FThe truck must be securely fastened when transported on a lorry or a trailer. The lorry
/ trailer must have fastening rings.
– To secure the truck attach the tensioning belt to the strap points (1) and secure
them to the fastening rings.
– Tighten the tensioning belt with the tensioner.
MLoading must be carried out by specially trained staff in accordance with
recommendations contained in Guidelines VDI 2700 and VDI 2703. In each case
correct measurements shall be determined and appropriate safety measures
adopted.
1
1

C 3
04.08.GB
3 Using the truck for the first time
MOnly operate the truck with battery current. Rectified AC current will damage the
electronic components. Cables connected to the battery (trailing cables) must be less
than 6 meters in length.
To prepare the truck after delivery or after transport, proceed as follows:
– Make sure the truck’s equipment is complete and in a satisfactory condition.
– Install battery (where required). Do not damage battery cables
(see Chapter D).
– Charge the battery (see Chapter D).
– Start up the truck in accordance with instructions (see Chapter E).
ZWhen the truck is parked, the running surface of the tyres will flatten. The flattening
will disappear after a short period of operation.
C 3
04.08.GB
3 Using the truck for the first time
MOnly operate the truck with battery current. Rectified AC current will damage the
electronic components. Cables connected to the battery (trailing cables) must be less
than 6 meters in length.
To prepare the truck after delivery or after transport, proceed as follows:
– Make sure the truck’s equipment is complete and in a satisfactory condition.
– Install battery (where required). Do not damage battery cables
(see Chapter D).
– Charge the battery (see Chapter D).
– Start up the truck in accordance with instructions (see Chapter E).
ZWhen the truck is parked, the running surface of the tyres will flatten. The flattening
will disappear after a short period of operation.