Juniper mesa 2 User manual

OWNER’S MANUAL
OWNER’S MANUAL

ii Mesa 2 Rugged Tablet Powered by Android
tel: [phone] lweb: www.junipersys.com
1132 W. 1700 N. Logan, UT 84321
Copyright ©May 2017, Juniper Systems, Inc. All rights
reserved. Information is subject to change without notice.
Juniper Systems®is a registered trademark of Juniper
Systems, Inc. Mesa 2™is a recognized trademark of Juniper
Systems, Inc.
Android™is a trademark of Google Inc.
The Bluetooth®word mark is owned by the Bluetooth SIG,
Inc. Any use of such marks by Juniper Systems, Inc. is under
license.
The names of other companies and products mentioned
herein may be the trademarks of their respective owners.
WARNING! This symbol indicates that failure to follow
directions could result in serious injury.
CAUTION: This symbol indicates that failure to follow
directions could result in damage to equipment or loss of
information.
Part Number 26621-01
!
!

Contents iii
CONTENTS
1Getting Started 1
Perform Initial Tasks 4
Turn the Mesa 2 on and Off 7
2 Standard Features 9
Operating System 10
Settings 12
Display and Touchscreen 12
Connector Ports 15
Battery Packs 15
LED Activity Indicators 18
Data Storage Options 19
Audio Features 21
Sleep, Power Off, Lock up, and Recovery 22
Sensors 24
Bluetooth®Wireless Communication 25
Wi-Fi Wireless Networking 26
3 Optional Features and Accessories 27
GPS/GNSS 28
Camera 31
4G LTE Data Modem 31
Barcode Imager 33
RFID Reader 39
RS-232 Port 44
Ofce Docking Station 46
Battery Charger 48
A Storage, Maintenance, and Recycling 49
Storing the Mesa 2 and Battery Pack 50
Protecting the Touchscreen 51
Recycling the Mesa 2 and Batteries 52

iv Mesa 2 Rugged Tablet Powered by Android
B Warranty and Repair Information 53
Limited Product Warranty 54
Complete Care Service Plans 57
C Warnings, Regulatory Information, Licensing 59
Product Warnings 60
Certications and Standards 62
Licensing Information 65
DSpecications 67
Index 77

1
GETTING STARTED

2Mesa 2 Rugged Tablet Powered by Android
Getting Started
The standard features for the Mesa 2 Rugged Tablet™
powered by Android from Juniper Systems include a 7”
display, capacitive touchscreen, keypad, Bluetooth, and
Wi-Fi. Standard accessories include a lithium-ion battery
pack, AC wall charger, hand strap, connector port cover, a
ne tip capacitive stylus and tether, and a foam tip stylus for
use in wet conditions. Other product congurations include
optional features. Refer to the specication appendix
for available congurations and details about optional
features.
The Anatomy of the Mesa 2
Front and Back Features
1Notication LEDs
2Touchscreen and Display
3Protective Over-molded Bumper
(all four edges)
4Microphone (one on each side)
5Ambient Light Sensor
6Front Facing Camera Lens, 2 MP
7Keypad
8Power Key
9Rear Facing Camera Lens, 8 MP
10 Camera Flash
11 Speaker
12 Battery Door Lock
13 Door to Removable Battery
Compartment and Card Slots
14 External Device Attachment
Point (1 of 3 on the back)
15 Location of Internal Battery
(not user accessible)
16 Storage Slot for Fine Tip Stylus
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16

Chapter 1 Getting Started 3
Battery Compartment and Card Slots
Connector Ports
Note: Your tablet might look different than these images.
1Battery Pack, Removable
2Battery Door
3Micro SIM Card Slot and
Micro SD/SDHC Card Slot
(underneath card retainer)
4Flexible Card Retainer
5 Battery Compartment
6Docking Connection
7Hand Strap Attachment
Point (2 on each side)
2
1
5
4
3
6
7
8 Connector Ports
9Connector Port Protector
10 12 VDC Power Input Jack
11 USB 3.0 Host, Full Size
12 Microphone/Speaker Jack
13 Storage Slot for Fine Tip Stylus
8
10 11 12
9
13

4Mesa 2 Rugged Tablet Powered by Android
Perform Initial Tasks
When you receive your Mesa 2, perform the tasks outlined in
this section before rst use.
Review Documentation
This owner’s manual and other documents like release
notes are available on our website at: www.junipersys.com/
Juniper-Systems-Rugged-Handheld-Computers/products/
Mesa-2/Support. View, download, and print documents
as desired, either on the Mesa 2 or another computer with
an internet connection. A PDF viewer is included with your
Mesa 2 apps.
Documentation will be updated during the life of the Mesa
2. Compare version numbers to see if a document has
changed.
Install the Battery Pack, Micro SD Card, and Micro SIM
Card
The Mesa 2 comes with a rechargeable, removable Li-
Ion battery pack. Install and charge the battery pack as
follows:
1. The battery compartment is accessed from the back of
the tablet. Push the battery lock switch in, slide it to the
unlocked position, and remove the door.
CAUTION: The Mesa 2 is not sealed against water and
dust when the battery door is not installed.
2. If you are using a micro SD card for additional memory
or a micro SIM card with the Cellular Data Modem
(optional), you can install them now before you install
the battery pack or at another time. If you do this,
make sure you replace the exible card retainer before
installation of the battery. See Chapter 2, Standard
Features, SD Cards for more details.
!

Chapter 1 Getting Started 5
3. Follow the graphic on the battery label to insert the
battery pack properly.
TO ENSURE DOOR SEAL, INSERT SIDE (A) FIRST!
PARA VEDAR A PORTA, INSIRA O LADO (A) PRIMEIRO!
PARA SELLAR LA PUERTA, INSERTE PRIMERO LADO (A)
ERST SEITE (A) EINLEGEN – SICHERT TÜRDICHTUNG!
P/ VEDAR A PORTA, INSIRA O LADO (A) PRIMEIRO!
(A)
(A)
Hold the battery so that the black tab on the front edge
of the battery is up and facing the door latch (this tab
helps you pull the battery out). Place the back edge
in rst, gently pushing it underneath the two battery
catches. Rotate the front edge down until it is in position.
CAUTION: Do not insert the battery pack straight down.
Damage to the unit could occur.
4. Replace the door and press down on it until the latch
pops into the locked position (from this view, the left side
of the door is inserted rst).
5. Attach the appropriate plug for your country into the
AC wall charger and plug it into a wall socket. Plug the
other end into the DC power jack on the Mesa 2.
!
Black Tab

6Mesa 2 Rugged Tablet Powered by Android
Note: Use the AC wall charger that came with the
Mesa 2 or an approved charger. See Appendix C, Wall
Charger Warnings, for details.
6. Charge the battery pack at room temperature (68°F or
20°C) for 6 hours (for the rst charge). While the battery
pack is charging, the red LED blinks. When it is fully
charged and external power is applied, the red LED is
solid. The battery charge level shown on the icon for
this battery (see the status bar at the top of the display)
does not report the correct charge until the battery is
fully charged for the rst time.
Note: If you have an optional internal battery as well as
a removable battery, the Mesa 2 does not recognize
the internal battery and the battery icon for this battery
is not shown on the status bar until the Mesa 2 is being
charged for the rst time.
Attach the Hand Strap and Stylus Tether
A hand strap, ne tip capacitive stylus, and tether are
included with the Mesa 2.
Hand Strap
To attach the hand strap to the Mesa 2, follow the images
below. You can attach it to the right or left side of the tablet:
1
2 3