Jura ENA 9 One Touch User manual

pt
es
nl
it
fr
ru
en
de
Instructions for Use ENA 9 One Touch
The Instructions for Use has been awarded the seal of
approval by the independent German Technical Inspection
Agency, TÜV SÜD, due to its easy-to-understand style, its
thoroughness and coverage of safety aspects.

2
Table of contents
Your ENA 9
Control elements 4
Important information 6
Proper use.................................................................................................................................................................6
For your safety .........................................................................................................................................................6
1 Preparing and using for the first time 7
JURA on the Internet ...............................................................................................................................................7
3-colour plain text display......................................................................................................................................7
Setting up the machine..........................................................................................................................................7
Filling the water tank ..............................................................................................................................................7
Filling the bean container ......................................................................................................................................7
First-time use............................................................................................................................................................8
Inserting and activating the filter.........................................................................................................................8
Determining and adjusting the water hardness................................................................................................9
Adjusting the grinder............................................................................................................................................ 10
2 Preparation 10
Coffee....................................................................................................................................................................... 10
Preparing two speciality coffees at the touch of a button.............................................................................. 11
Aroma Boost............................................................................................................................................................ 11
Latte macchiato, cappuccino................................................................................................................................ 11
Permanently setting the amount of water for the cup size............................................................................ 11
Ground coffee..........................................................................................................................................................12
Hot water..................................................................................................................................................................13
3 Daily operation 13
Switching on the machine....................................................................................................................................13
Daily maintenance..................................................................................................................................................13
Switching off the machine....................................................................................................................................13
4 Permanent settings in programming mode 13
Products ...................................................................................................................................................................13
Energy-saving mode............................................................................................................................................. 14
Automatic switch-off..............................................................................................................................................15
Rinses........................................................................................................................................................................15
Unit for amount of water..................................................................................................................................... 16
Language................................................................................................................................................................. 16
5 Maintenance 16
Rinsing the machine ............................................................................................................................................. 16
Rinsing the milk system........................................................................................................................................17
Cleaning the milk system......................................................................................................................................17

3
pt
es
nl
it
fr
ru
en
de
Table of contents
Dismantling and rinsing the dual spout............................................................................................................ 18
Changing the filter................................................................................................................................................. 18
Cleaning the machine........................................................................................................................................... 19
Descaling the machine ....................................................................................................................................... 20
Descaling the water tank...................................................................................................................................... 21
Cleaning the bean container ............................................................................................................................... 21
6 Display messages 22
7 Troubleshooting 23
8 Transport and environmentally friendly disposal 24
Transport / Emptying the system.......................................................................................................................24
Disposal...................................................................................................................................................................24
9 Technical data 24
10 Index 25
11 JURA contact details / Legal information 27
Symbol description
Warnings
J WARNING
J CAUTION
Always take note of any information marked with the words CAUTION or WARNING
and a warning sign. The signal word WARNING draws your attention to potential
serious injury, and the signal word CAUTION to potential minor injury.
CAUTION CAUTION draws your attention to potential damage to the machine.
Symbols used
TPrompt to take action. This symbol means that you are being prompted to perform some
action.
EInformation and tips to make it even easier to use your ENA.
@References to the JURA website, which provides further information that may be of interest
to you: www.jura.com
READY Display

4
Control elements
Control elements











1 Water tank
2 Powder chute for ground coffee
3 Mains cable (back of the machine)
4 Milk pipe
5 Coffee grounds container
6 Drip tray
7 Cup platform
8 Bean container cover
9 lSwitch for hot water preparation
10 Hot-water nozzle
11 Height-adjustable dual spout

5
Control elements
pt
es
nl
it
fr
ru
en
de










1 Cover
2 cMaintenance button
3 /Cappuccino button
4 (Latte Macchiato button
5 QOn/Off button
6 Grinding wheel
7 )Aroma Boost button
8 >Coffee button
9 gRotary Switch
10 Display

6
Important information
Important information
Proper use
The machine is designed and intended for private
domestic use. It should only be used for coffee
preparation and to heat milk and water. Use for
any other purpose will be deemed improper.
JURA Elektroapparate AG cannot accept any
responsibility for the consequences of improper
use.
Before using the machine read these instructions
for use thoroughly and completely and comply
with the instructions they contain. A warranty
service is not applicable for damage or defects
caused by non-compliance with the instructions
for use. Keep these instructions for use close to the
machine and pass them on to the next user.
For your safety
Please carefully read and observe the important
safety information set out below.
To avoid danger of potentially fatal electric shock:
UNever use a machine which is damaged or has
a defective mains cable.
UIn the event of signs of damage, for example if
there is a smell of burning, unplug the
machine immediately from the mains supply
and contact JURA service.
UIf the mains cable of this machine is damaged,
it must be repaired either directly by JURA or
by an authorised JURA service centre.
UMake sure that the ENA and the mains cable
are not located close to hot surfaces.
UBe careful to ensure that the mains cable is not
trapped and does not rub against sharp edges.
UNever open and repair the machine yourself.
Do not modify the machine in any way that is
not described in these instructions for use. The
machine contains live parts. If opened, there is
a danger of potentially fatal injury. Repairs
may only be carried out by authorised JURA
service centres, using original spare parts and
accessories.
A defective machine is not safe and could cause
injury or fire. To avoid damage and any associated
risk of injury or fire:
UNever allow the mains cable to loosely hang
down. The mains cable could pose a tripping
hazard or become damaged.
UProtect the ENA from environmental influ-
ences such as rain, frost and direct sunlight.
UDo not immerse the ENA, mains cable or
connections in water.
UDo not put the ENA or any individual parts in
the dishwasher.
USwitch your ENA off before cleaning work with
the On/Off button. Always wipe the ENA with a
damp cloth rather than a wet one, and protect
it from prolonged exposure to water splash.
UOnly connect the machine to the mains
voltage in accordance with the information on
the rating plate. The rating plate is located on
the underside of your ENA. Further technical
data is provided in these instructions for use
(see Chapter 9 ‘Technical data’).
UPlease only use original JURA maintenance
products. Use of products that are not
explicitly recommended by JURA could
damage the ENA.
UDo not use any coffee beans treated with
additives or caramelised coffee beans.
UOnly fill the water tank with fresh, cold water.
UDo not fill the bean container with water.
USwitch the machine off with the On/Off button
if you are going to be absent for a longer
period of time and remove the mains plug
from the power socket.
People, including children, who
Udo not have the physical, sensory or mental
capabilities to use the machine safely or

7
1 Preparing and using for the first time
pt
es
nl
it
fr
ru
en
de
Uare inexperienced or lack knowledge in how to
use the machine safely
must be supervised by a responsible person when
using it, or must be instructed in how to use it
correctly.
Safety when handling the CLARIS Blue filter
cartridge:
UFilter cartridges should be kept out of the
reach of children.
UStore filter cartridges in a dry place in the
sealed packaging.
UProtect cartridges from heat and direct
sunlight.
UDo not use damaged filter cartridges.
UDo not open filter cartridges.
1 Preparing and using for the
first time
This chapter provides you with the information
you need to use your ENA without any problems.
You will prepare your ENA step-by-step to enjoy
your first perfect cup of coffee.
JURA on the Internet
Visit us on the Internet.
@On the JURA website (www.jura.com) you
will find interesting and up-to-date
information on your ENA and on every
aspect of coffee.
3-colour plain text display
Your ENA features a 3-colour plain text display. The
colours of the display texts have the following
meanings:
UGreen: The ENA is ready for use.
URed: The ENA is prompting you to perform
some action.
UYellow: You are in programming mode.
Setting up the machine
When setting up your ENA, please note the
following:
UPlace the machine on a horizontal surface that
is not sensitive to water.
UChoose a spot for your ENA which protects the
machine against overheating. Ensure that the
ventilation slots are not covered.
Filling the water tank
To enjoy the perfect cup of coffee we recommend
changing the water every day.
CAUTION
Milk, sparkling mineral water or other liquids can
damage the water tank or the machine.
TOnly fill the water tank with fresh, cold water.
TRemove the water tank and rinse with cold
water.
TFill the water tank with fresh, cold water and
reinsert it.
Filling the bean container
CAUTION
Coffee beans which have been treated with
additives (e.g. sugar), preground coffee or
freeze-dried coffee will damage the grinder.
TOnly use untreated coffee beans to refill the
bean container.
TRemove the bean container cover.

8
1 Preparing and using for the first time
TRemove any dirt or foreign objects from
inside the bean container.
TFill the bean container with coffee beans.
TClose the bean container.
First-time use
EThe On/Off button also acts as a power
switch. When the ENA is switched off, the
machine does not consume standby energy.
JWARNING
If the machine is operated with a defective mains
cable, there is a danger of potentially fatal electric
shock.
TNever use a machine which is damaged or
has a defective mains cable.
Precondition: The water tank and bean container
are full.
TInsert the mains plug into a power socket.
QTPress the On/Off button to switch the
machine on.
SPRACHE DEUTSCH
gTTurn the Rotary Switch until the required
language is displayed, for example
LANGUAGE ENGLISH.
kTPress the Rotary Switch to confirm the
language setting.
OK, the language is set.
PRESS ROTARY
TPlace a receptacle under the dual spout.
kTPress the Rotary Switch.
SYSTEM FILLING
HEATING
PRESS ROTARY
kTPress the Rotary Switch to start the rinse.
RINSING, the system rinses itself,
stopping automatically.
READY
Inserting and activating the filter
Your ENA no longer has to be descaled if you are
using the CLARIS Blue filter cartridge.
EPerform the ‘inserting the filter’ operation
without any interruptions. This will ensure
that your ENA always produces its best.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until FILTER- is
displayed.
kTPress the Rotary Switch to enter the
programme item.
NO-
gTTurn the Rotary Switch until YESp is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK
INSERT FILTER
TRemove and empty the water tank.
TOpen the filter holder.

9
1 Preparing and using for the first time
pt
es
nl
it
fr
ru
en
de
TInsert the filter cartridge into the water tank,
exerting slight pressure.
TClose the filter holder. It will click into place
audibly.
EAfter two months, the filter will cease to
work. You can check the elapsed time by
referring to the date plate on the filter holder
in the water tank.
TFill the water tank with fresh, cold water and
reinsert it.
TPlace a receptacle (at least 500 ml) under the
hot-water nozzle.
kTPress the Rotary Switch.
OPEN TAP
lTTurn the switch anticlockwise to position m.
FILTER RINSING, water flows out of
the hot-water nozzle.
EYou can interrupt rinsing of the filter at any
time. To do this, turn the switch clockwise.
Turn the switch anticlockwise to continue
rinsing the filter.
EThe water may be slightly discoloured. This
is not harmful to health and does not affect
the taste.
Rinsing of the filter stops automatically,
CLOSE TAP.
yTTurn the switch clockwise to position o.
HEATING
READY
The filter is now activated.
Determining and adjusting the water
hardness
EIf you are using the CLARIS Blue filter
cartridge and have activated it in program-
ming mode, you will not be able to adjust
the water hardness.
The harder the water is, the more frequently the
ENA needs to be descaled. It is therefore important
to adjust the water hardness.
The water hardness can be adjusted on a continu-
ous scale between 1° dH and 30° dH.
Determining the water hardness
You can find out what the water hardness is by
using the Aquadur® test strip supplied as standard.
THold the test strip briefly (for one second)
under running water.
TShake off the water.
TWait for about one minute.
TYou will then be able to read the degree of
water hardness from the discolouration of
the Aquadur® test strip and the description
on the packaging.
The water hardness can now be adjusted.
Adjusting the water hardness
Example: Change the water hardness setting from
16°dH to 25°dH.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until HARDNESS
is displayed.

10
2 Preparation
kTPress the Rotary Switch to enter the
programme item.
16°dH
gTTurn the Rotary Switch until 25°dH is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the water hardness is set.
HARDNESS
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Adjusting the grinder
You can adjust the grinder on a continuous scale to
suit the degree of roast of your coffee.
CAUTION
If you adjust the consistency of grind when the
grinder is not operating, the grinding wheel could
be damaged.
TOnly adjust the consistency of grind when
the grinder is running.
The consistency of grind setting is correct if the
coffee flows regularly from the coffee spout. In
addition a fine, thick crema forms.
Example: Change the consistency of grind during
the preparation of a coffee.
TPlace a cup under the dual spout.
>TPress the Coffee button to start preparation.
TTurn the grinding wheel to the desired
position while the grinder is running.
1COFFEE, the preset amount of water
flows into the cup and preparation stops
automatically.
READY
2 Preparation
EYou can interrupt preparation at any time
while a speciality coffee or speciality coffee
with milk is being prepared. Just press any
button.
EBefore and during the grinding operation
you can select the coffee strength for
‘1 coffee’, ‘cappuccino’ and ‘latte macchiato’:
MILD, NORMAL, STRONG.
EDuring preparation, you can change the
preset amount of water by turning the
Rotary Switch.
EYou can follow the current status of
preparation on the progress bar.
You can make permanent settings for all products
in programming mode (see Chapter 4 ‘Permanent
settings in programming mode – Products’).
Coffee
Precondition: READY is displayed.
TPlace a cup under the dual spout.
>TPress the Coffee button to start preparation.
1COFFEE, the preset amount of water
flows into the cup.
Preparation stops automatically.
READY

11
2 Preparation
pt
es
nl
it
fr
ru
en
de
Preparing two speciality coffees at the
touch of a button
The preparation of 2 espressi and 2 coffees follows
this same model.
Example: Prepare two espressi.
Precondition: READY is displayed.
TPlace two espresso cups under the dual
spout.
)TPress the Aroma Boost button twice (within
two seconds) to start preparation.
2ESPRESSI, the preset amount of
water flows into the cups.
Preparation stops automatically.
READY
Aroma Boost
When you prepare an ‘Aroma Boost’ the maximum
possible amount of powder is freshly ground and
extracted to make an extra strong espresso or
coffee.
Precondition: READY is displayed.
TPlace a cup under the dual spout.
)TPress the Aroma Boost button to start
preparation.
SPECIAL, the preset amount of water
flows into the cup.
Preparation stops automatically.
READY
Latte macchiato, cappuccino
Your ENA can prepare a latte macchiato or
cappuccino at the touch of a button. There is no
need to move the glass or cup.
Example: Proceed as follows to prepare one latte
macchiato.
Precondition: READY is displayed.
TPlace a glass under the dual spout.
TRemove the protective cover of the dual
spout.
TConnect the milk pipe to the dual spout.
TImmerse the other end of the milk pipe in a
receptacle with milk (figure: JURA 0.4 litre
stainless steel vacuum milk container).
EEnsure that the filling height of the milk is
no higher than the milk pipe connection on
the dual spout.
(TPress the Latte Macchiato button.
LATTE MAC., the milk foam is prepared.
Preparation stops automatically when the
preset amount of milk is reached.
PAUSE
EThere is a short interval while the hot
milk separates from the milk foam. This
allows the typical layers of a latte macchiato
to form. You can choose the length of this
interval in programming mode (see
Chapter 4 ‘Permanent settings in program-
ming mode – Products’).
LATTE MAC., coffee preparation starts.
The preset amount of water flows into the
cup.
Preparation stops automatically.
READY
Permanently setting the amount of water
for the cup size
It is easy to make permanent settings for the
amount of water for all speciality coffees according
to the cup size. Adjust the amount once as shown
in the following example. Every time you prepare a
drink in the future, this amount of water will be
dispensed.

12
2 Preparation
Example: Permanently adjust the amount of
water for one coffee to the cup size.
Precondition: READY is displayed.
TPlace a cup under the dual spout.
>TPress and hold the Coffee button.
1COFFEE, the grinding operation starts.
>TContinue to hold the Coffee button down
until ENOUGH COFFEE? appears.
>TRelease the Coffee button.
Preparation starts and the coffee flows into
the cup.
TPress any button as soon as there is
sufficient coffee in the cup.
OK, 1COFFEE, the set amount of water
for one coffee is permanently stored.
READY
EYou can alter this setting at any time by
repeating the above procedure.
Ground coffee
You can choose to use a second coffee variety, for
example decaffeinated coffee, with the powder
chute for ground coffee.
ENever add more than two level measuring
spoons of ground coffee.
EUse ground coffee which is not ground too
finely. Very fine coffee can block up the
system so that the coffee only comes out in
drips.
EIf you did not fill the machine with a
sufficient amount of ground coffee, NOT
ENOUGH POWDER is displayed and the
ENA stops the operation.
EThe desired speciality coffee must be
prepared within approximately one minute
after filling with the ground coffee.
Otherwise the ENA stops the operation and
is once more ready for use.
The preparation of 1 coffee, 2 coffees, 2 espressi,
cappuccino and latte macchiato with ground cof-
fee follows this model. It is not possible to prepare
an Aroma Boost with ground coffee.
Example: Prepare a cup of coffee using ground
coffee.
Precondition: READY is displayed.
TPlace a cup under the dual spout.
TOpen the powder chute.
FILL POWDER
TPlace the filler funnel for ground coffee on
the powder chute.
TPlace one level measuring spoon of ground
coffee into the filler funnel.
TRemove the filler funnel.
TClose the powder chute.
SELECT BUTTON
>TPress the Coffee button to start preparation.
1COFFEE, the preset amount of water
flows into the cup.
Preparation stops automatically.
READY
EIt is also possible to prepare two cups of
ground coffee. To do this, place two cups
under the dual spout and add two level
measuring spoons of ground coffee into the
filler funnel. Press the Coffee button >
twice (within two seconds) to start
preparation.

13
3 Daily operation
pt
es
nl
it
fr
ru
en
de
Hot water
JCAUTION
There is a danger of scalding from hot water
splashes.
TAvoid direct contact with the skin.
Precondition: READY is displayed.
TPlace a cup under the hot-water nozzle.
lTTurn the switch anticlockwise to position m.
WATER, hot water flows into the cup.
yTTurn the switch clockwise when there is
sufficient water in the cup.
READY
3 Daily operation
Switching on the machine
When the ENA is switched on, a prompt to
perform a rinse operation automatically appears.
QTPress the On/Off button to switch the ENA on.
HEATING
PRESS ROTARY
TPlace a receptacle under the dual spout.
kTPress the Rotary Switch to start the rinse.
RINSING, the system rinses itself,
stopping automatically.
READY
Daily maintenance
To ensure that you get many years of reliable
service out of your ENA and to guarantee the
optimum coffee quality, the machine requires daily
maintenance.
TRemove the drip tray.
TEmpty the coffee grounds container and
drip tray and rinse with warm water.
TReinsert the coffee grounds container and
the drip tray.
TRinse the water tank with clean water.
TDismantle and rinse the dual spout (see
Chapter 5 ‘Maintenance – Dismantling and
rinsing the dual spout’).
TWipe the surface of the machine with a
clean, soft, damp cloth (e.g. microfibre
cloth).
Switching off the machine
When the ENA is switched off, the system is
automatically rinsed if a speciality coffee has been
prepared. If cappuccino or latte macchiato has
been prepared, the cappuccino rinse also takes
place.
TPlace a receptacle under the dual spout.
QTPress the On/Off button.
RINSING, CAPPUCCINO
RINSING, the system rinses itself,
stopping automatically. The ENA is switched
off.
EWhen the ENA is switched off with the On/
Off button, the machine does not consume
standby energy.
4 Permanent settings in pro-
gramming mode
Products
You can make the following permanent settings for
the speciality coffees:
UAmount of water: 25ML – 240ML (per
cup)
UCoffee strength (for 1 coffee): MILD,
NORMAL, STRONG
UTemperature: NORMAL, HIGH
You can make the following permanent settings for
latte macchiato and cappuccino:
UAmount of milk foam: 3SEC – 120SEC
UInterval: 0SEC – 60SEC

14
4 Permanent settings in programming mode
UCoffee strength: MILD, NORMAL,
STRONG
UAmount of water: 25ML – 240ML
UTemperature: NORMAL, HIGH
Permanent settings in programming mode always
follow the same model.
Example: Permanently change the coffee strength
(FLAVOUR) for 1 coffee from NORMAL to
STRONG.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until PRODUCT is
displayed.
kTPress the Rotary Switch to enter the
programme item.
SELECT BUTTON
ENext select the button of the product for
which you would like to make settings. No
product is prepared at this point.
ETo change the setting for a double product,
press the corresponding button twice within
two seconds.
>TPress the Coffee button.
1COFFEE
WATER
gTTurn the Rotary Switch until FLAVOUR is
displayed.
kTPress the Rotary Switch to enter the
programme item.
NORMAL
gTTurn the Rotary Switch until STRONG is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the coffee strength is set.
FLAVOUR
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit the pro-
gramme item.
PRODUCT
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Energy-saving mode
The ENA can be permanently set to an energy-sav-
ing mode (Energy Save Mode, E.S.M.©):
UENERGY-
UThe ENA is constantly ready for use.
UAll speciality coffees as well as hot water can
be prepared without having to wait.
UENERGYp
USoon after the last preparation, the ENA
stops heating up. As soon as the energy-sav-
ing temperature is reached, this is indicated
in the display by the message ENERGY
ON – this may last several minutes. The
machine must heat back up before the next
preparation.
UBefore coffee and hot water preparation, the
machine heats up.
Example: Change the energy-saving mode from
ENERGY- to ENERGYp.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until ENERGY- is
displayed.
kTPress the Rotary Switch to enter the
programme item.
ECONOMY-
gTTurn the Rotary Switch until ECONOMYp
is displayed.

15
4 Permanent settings in programming mode
pt
es
nl
it
fr
ru
en
de
kTPress the Rotary Switch to confirm the
setting.
OK, the energy-saving mode is set.
ENERGYp
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Automatic switch-off
By instructing your ENA to automatically switch
itself off, you can cut down your energy consump-
tion. If this function is activated, your ENA switches
off automatically after the preset time following
the last action on the machine.
The automatic switch-off can be set to between
15 minutes and 9 hours.
Example: Change the automatic switch-off time
from 2HRS to 1HRS.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until OFF AFTER
is displayed.
kTPress the Rotary Switch to enter the
programme item.
2HRS
gTTurn the Rotary Switch until 1HRS is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the automatic switch-off time is set.
OFF AFTER
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Rinses
In the programme item RINSES you can make
the following settings:
UINIT RINSE MANUAL
UThe switch-on rinse must be started
manually.
UINIT RINSE AUTOMATIC
UThe switch-on rinse is started automatically.
UC-RINSE AFTER10'
UYou are prompted to perform a cappuccino
rinse 10 minutes after preparation of a
speciality coffee with milk.
UC-RINSE NOW
UYou are prompted to perform a cappuccino
rinse immediately after preparation of a
speciality coffee with milk.
Example: Change the setting such that the
cappuccino rinse is performed immediately after
preparation of a speciality coffee with milk.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until RINSES is
displayed.
kTPress the Rotary Switch to enter the
programme item.
INIT RINSE
gTTurn the Rotary Switch until C-RINSE is
displayed.
kTPress the Rotary Switch to enter the
programme item.
AFTER10'
gTTurn the Rotary Switch until NOW is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK
C-RINSE
gTTurn the Rotary Switch until EXIT is
displayed.

16
5 Maintenance
TPress the Rotary Switch to exit the pro-
gramme item.
RINSES
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Unit for amount of water
You can change the unit for the amount of water
from ‘ml’ to ‘oz’.
Example: Change the unit for the amount of water
from ML to OZ.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until DISPLAY is
displayed.
kTPress the Rotary Switch to enter the
programme item.
ML
gTTurn the Rotary Switch until OZ is displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the unit for the amount of water is set.
DISPLAY
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
READY
Language
In this programme item you can set the language
used by your ENA.
Example: Change the language from ENGLISH
to DEUTSCH.
Precondition: READY is displayed.
kTPress and hold the Rotary Switch until
RINSE appears.
gTTurn the Rotary Switch until LANGUAGE
is displayed.
kTPress the Rotary Switch to enter the
programme item.
ENGLISH
gTTurn the Rotary Switch until DEUTSCH is
displayed.
kTPress the Rotary Switch to confirm the
setting.
OK, the language is set.
SPRACHE
gTTurn the Rotary Switch until EXIT is
displayed.
kTPress the Rotary Switch to exit programming
mode.
BEREIT
5 Maintenance
Your ENA has the following integrated mainte-
nance programmes:
UCappuccino frother cleaning (C-CLEAN)
URinsing the machine (RINSE)
UCappuccino rinse (C-RINSE)
UCleaning the machine (CLEAN)
UChanging the filter (FILTER)
UDescaling the machine (DE-SCALE)
Rinsing the machine
You can initiate the rinse operation manually at
any time.
Precondition: READY is displayed.
TPlace a receptacle under the dual spout.
kTPress and hold the Rotary Switch until
RINSE appears.
kTPress the Rotary Switch to enter the
programme item.
C-CLEAN
gTTurn the Rotary Switch until RINSE is
displayed.

17
5 Maintenance
pt
es
nl
it
fr
ru
en
de
kTPress the Rotary Switch to initiate the rinse
operation.
RINSING, the system rinses itself,
stopping automatically.
READY
Rinsing the milk system
After each milk preparation, the ENA prompts you
to perform a cappuccino rinse.
Precondition: CAPPUCCINO RINSE is
displayed.
TPlace a receptacle under the dual spout.
kTPress the Rotary Switch to start the
cappuccino rinse.
CAPPUCCINO RINSING, the milk
system is rinsed.
The rinse stops automatically and READY
appears on the display.
Cleaning the milk system
The dual spout should be cleaned daily if milk has
been prepared to make sure it functions perfectly.
Your ENA will not prompt you to clean the dual
spout.
CAUTION
If the wrong cleaning agent is used, the machine
could be damaged and/or traces could be left
behind in the milk.
TUse only original JURA maintenance
products.
EJURA Cappuccino Cleaner is available from
stockists.
kTPress and hold the Rotary Switch until
RINSE appears.
kTPress the Rotary Switch to enter the
programme item.
C-CLEAN
kTPress the Rotary Switch to start cappuccino
frother cleaning.
CLEANER FOR CAPPU.
TRemove the milk pipe from the receptacle
with milk.
TPour 250 ml of fresh water into a receptacle
and add one capful (max. 15 ml) of Cappuc-
cino Cleaner.
TImmerse the milk pipe in the receptacle.
TPlace another receptacle under the dual
spout.
kTPress the Rotary Switch.
CLEANING, the milk system and the pipe
are cleaned.
The operation is interrupted, WATER FOR
CAPPUCCINO.
TRinse the receptacle thoroughly, fill it with
250 ml of fresh water and immerse the milk
pipe in it.
TEmpty the receptacle under the dual spout
and place it back underneath.
kTPress the Rotary Switch.
CLEANING, the milk system and the pipe
are rinsed with fresh water.
The operation stops automatically.
READY

18
5 Maintenance
Dismantling and rinsing the dual spout
The dual spout should be dismantled and rinsed
daily if milk has been prepared to make sure it
functions perfectly. Your ENA will not prompt you
to clean the dual spout.
TRemove the milk pipe and rinse thoroughly
under running water.
TPress the releasing devices and pull the dual
spout down and off.
TPush the milk system down and remove it.
TDismantle the milk system into its individual
parts.
TRinse all parts under running water. If there
are severely dried on milk residues, firstly
immerse the individual parts in JURA
Cappuccino Cleaner and then clean them
thoroughly.
TFit the air intake pipe.
TReassemble the milk system, noting the
numbering on the parts.
TInsert the assembled individual parts into
the dual spout and press them together.
TFit the dual spout on the machine. It will
click into place audibly.
Changing the filter
EAfter 50 litres of water have flowed through,
the filter will cease to work. Your ENA will
automatically prompt you to change the
filter.
EAfter two months, the filter will cease to
work. You can check the elapsed time by
referring to the date plate on the filter holder
in the water tank.




19
5 Maintenance
pt
es
nl
it
fr
ru
en
de
EIf the CLARIS Blue filter cartridge is not
activated in programming mode, you will
not be prompted to change the filter.
Precondition: FILTER / READY is displayed.
TOpen the cover behind the Rotary Switch.
cTPress the Maintenance button.
INSERT FILTER
TRemove and empty the water tank.
TOpen the filter holder and remove the old fil-
ter cartridge.
TInsert a new filter cartridge into the water
tank, exerting slight pressure.
TClose the filter holder. It will click into place
audibly.
TFill the water tank with fresh, cold water and
reinsert it.
TPlace a receptacle (at least 500 ml) under the
hot-water nozzle.
kTPress the Rotary Switch.
OPEN TAP
lTTurn the switch anticlockwise to position m.
FILTER RINSING, water flows out of
the hot-water nozzle.
EYou can interrupt rinsing of the filter at any
time. To do this, turn the switch clockwise.
Turn the switch anticlockwise to continue
rinsing the filter.
EThe water may be slightly discoloured. This
is not harmful to health and does not affect
the taste.
Rinsing of the filter stops automatically,
CLOSE TAP.
yTTurn the switch clockwise to position o.
HEATING
READY
Cleaning the machine
After 180 preparations or 80 switch-on rinses, the
ENA will prompt you to clean it.
CAUTION
If the wrong cleaning agent is used, the machine
could be damaged and/or traces could be left
behind in the water.
TUse only original JURA maintenance
products.
EThe cleaning programme lasts approxi-
mately 15 minutes.
EDo not interrupt the cleaning programme.
The quality of cleaning will be impaired if
you do so.
EJURA cleaning tablets are available from
stockists.
Precondition: CLEAN / READY is displayed.
TOpen the cover behind the Rotary Switch.
cTPress the Maintenance button.
EMPTY TRAY
TEmpty the drip tray and coffee grounds
container and reinsert them.
PRESS ROTARY
TPlace a receptacle under the dual spout.
kTPress the Rotary Switch to start cleaning.
CLEANING, water flows out of the dual
spout.
The operation is interrupted, ADD
TABLET.

20
5 Maintenance
TOpen the powder chute for ground coffee
and drop in a JURA cleaning tablet.
TClose the powder chute for ground coffee.
PRESS ROTARY
kTPress the Rotary Switch.
CLEANING, water flows out of the dual
spout repeatedly.
EMPTY TRAY
TEmpty the drip tray and coffee grounds
container and reinsert them.
HEATING
READY
Descaling the machine
The ENA builds up deposits of limescale over time
and automatically prompts you to descale it when
necessary. The degree of calcification depends on
the hardness of your water.
JCAUTION
If the descaling agent comes into contact with the
skin or eyes, this can cause irritation.
TAvoid contact with the skin or eyes.
TRinse off descaling agent with clean water.
Should you get any descaling agent in your
eye, see a doctor.
CAUTION
If the wrong descaling agent is used, the machine
could be damaged and/or traces could be left
behind in the water.
TUse only original JURA maintenance
products.
CAUTION
If the descaling operation is interrupted, there may
be damage to the machine.
TAllow the descaling programme to run to
the end.
CAUTION
If the descaling agent comes into contact with
sensitive surfaces (e.g. marble), damage cannot be
ruled out.
TClean up any splashes immediately.
EThe descaling programme lasts approxi-
mately 40 minutes.
EJURA descaling tablets are available from
stockists.
EIf you use a CLARIS Blue filter cartridge and
this is activated, you will not be prompted to
descale.
Precondition: DE-SCALE / READY is
displayed.
TOpen the cover behind the Rotary Switch.
cTPress the Maintenance button.
EMPTY TRAY
TEmpty the drip tray and coffee grounds
container and reinsert them.
AGENT IN TANK
TRemove and empty the water tank.
TCompletely dissolve the contents of one blis-
ter (three JURA descaling tablets) in a
receptacle holding 500 ml of water. This may
take several minutes.
TPour the solution into the empty water tank
and reinsert the tank.
OPEN TAP