Jvc Kw-xg704 Guide

KW-XG704

Installation/Connection Manual

0407DTSMDTJEIN

Battery Remote controller

Binding screws (M5 × 8 mm)

Power cord

Flat countersunk screws (M5 × 8 mm)

GET0459-002A

[UI]

This unit is designed to o erate on 12 V DC, NEGATIVE ground electrical systems. If your vehicle does not have this system, a voltage inverter is required, which can be urchased at JVC car audio dealers.

WARNINGS

To revent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Be sure to ground this unit to the car s chassis again after installation.

Notes:

• Re lace the fuse with one of the s ecified rating. If the fuse blows frequently, consult your JVC car audio dealer.

• If noise is a roblem...

This unit incor orates a noise filter in the ower circuit. However, with some vehicles, clicking or other unwanted noise may occur. If this ha ens, connect the unit’s rear ground terminal to the car’s chassis using

shorter and thicker cords, such as co er braiding or gauge wire. If noise still ersists, consult your JVC car audio dealer.

• It is recommended to connect to the s eakers with maximum ower of more than 50 W (both at the rear and at the front, with an im edance of 4 Ω to 8 Ω). If the maximum ower is less than 50 W, change

“AMP GAIN” setting to revent the s eakers from being damaged (see age 25 of the INSTRUCTIONS).

• The heat sink becomes very hot after use. Be careful not to touch it when removing this unit.

Parts list for installation and connection

The following arts are rovided for this unit. If any item is missing, consult your JVC car audio dealer immediately.

Plate for use with a Nissan car

When installating the unit in a Nissan car

Fix the su lied late as illustrated.

Plate for use with a Nissan car

TROUBLESHOOTING

• The fuse blows.

* Are the red and black leads connected correctly?

• Power cannot be turned on.

* Is the yellow lead connected?

• No sound from the speakers.

* Is the s eaker out ut lead short-circuited?

• Sound is distorted.

* Is the s eaker out ut lead grounded?

* Are the “–” terminals of L and R s eakers grounded in common?

• Noise interfere with sounds.

* Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?

• This unit becomes hot.

* Is the s eaker out ut lead grounded?

* Are the “–” terminals of L and R s eakers grounded in common?

• This unit does not work at all.

* Have you reset your unit?

Heat sink

Rear view

Install1_KW-XG704[UI]f.indd 1Install1_KW-XG704[UI]f.indd 1 4/13/07 10:13:31 AM4/13/07 10:13:31 AM

INSTALLATION (IN-DASH MOUNTING)

The following illustration shows a ty ical installation. However, you should make adjustments corres onding to your s ecific car. In this case consult the manual included with the installation kit.

In some case, de ending on the ty e and the model of your car, it is not ossible to install the unit into the center console. If you have any questions or require information regarding installation kits, consult your JVC

car audio dealers or a com any su lying kits.

• If you are not sure how to install this unit correctly, have it installed by a qualified technician.

Before installing the unit

• When mounting the unit, be sure to use the screws rovided, as instructed. If other screws are used, there is a ossibility that arts could become loose or damaged.

• When tightening screws or bolts be careful not to inch any connection cord.

1 Remove the audio system originally installed together with the mounting brackets.

Note: Be sure to kee all the screws and arts removed from your car for future use.

2 Attach the mounting brackets (removed from the car), to this unit (see below).

3 Connect the wires (see diagram ).

4 Fix this unit to the car using the screws removed in ste 1.

• See “Caution” below.

The following example shown is for installation in a Toyota. For more details, consult your JVC car audio dealer.

Screws su lied for this unit

Mounting bracket removed from the car

Screws su lied for this unit

Screw removed from the car in ste 1

Securely connect the ground wire to the metal body of the car using the

screw originally fixed to the metal body of the car.

Mounting bracket removed from the car

Screws supplied for this unit:

Select the ro er screw ty e, fitting to your car.

Binding screws (M5 × 8 mm) Flat countersunk screws (M5 × 8 mm)

Caution:

To install the mounting brackets to the unit, use only the su lied screws (M5 × 8 mm).

If you use any screw longer than 8 mm, the unit can be damaged.

Install the unit at an angle of less than 30°.

If there is an interfering tab on the mounting bracket,

bend it flat.

Install1_KW-XG704[UI]f.indd 2Install1_KW-XG704[UI]f.indd 2 4/13/07 10:13:35 AM4/13/07 10:13:35 AM

Line out (see diagram )

15 A fuse

Black

Blue with white stripe

Red

Yellow *2

Brown

To metallic ody or chassis of the car

Ignition switch

Fuse lock

To an accessory terminal in the fuse lock

To the remote lead of other equipment (200 mA max.)

To cellular phone system

White with lack stripe

To a live terminal in the fuse lock connecting to the car attery ( ypassing

the ignition switch) (constant 12 V)

To external components (see diagram )

To car light control switch

Orange with white stripe

To su woofer (see diagram )

Antenna terminal

PurplePurple with lack stripeGreenGreen with lack stripeGrayGray with lack stripe

White

Right speaker (rear)Left speaker (rear)Right speaker (front)Left speaker (front)

To the automatic antenna if any (250 mA max.)

Blue

ATypical connections

Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.

The leads of the power cord and those of the connector from the car ody may e different in color.

1 Connect the colored leads of the power cord in the order specified in the illustration elow.

2 Connect the antenna cord.

3 Finally connect the wiring harness to the unit.

*1 Not supplied for this unit.

*2 Before checking the operation of this unit prior to installation, this lead must e connected, otherwise power cannot e turned on.

PRECAUTIONS on power supply and spea er connections:

• DO NOT connect the spea er leads of the power cord to the car battery; otherwise, the unit will be seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

ELECTRICAL CONNECTIONS

Install2_KW-XG704[UI]f.indd 3Install2_KW-XG704[UI]f.indd 3 4/13/07 10:15:13 AM4/13/07 10:15:13 AM

JVC CD changer

Apple iPod

JVC D. player

CD changer jack

External component

with or without

Remote lead ( lue with white stripe) To the remote lead of other equipment or automatic antenna if any

Front speakers

JVC Amplifier

Rear speakers

Y-connector (not supplied for this unit)

Su woofer

JVC Amplifier

Front speakers

JVC Amplifier

BConnecting the external amplifiers and subwoofer

You can connect amplifiers to upgrade your car stereo system.

• Connect the remote lead ( lue with white stripe) to the remote lead of the other equipment so that it can e controlled through this unit.

• Disconnect the spea ers from this unit, connect them to the amplifier. Leave the spea er leads of this unit unused.

You can connect these components as illustrated elow.

• All the components, adapters, or signal cords need to e purchased separately.

CAUTION:

Before connecting the external components, make sure that the unit is turned off.

• To use JVC CD changer, Apple iPod or JVC D. player, set the external input setting to “CHANGER” (see page 25 of the INSTRUCTIONS).

• To use other external components via KS-U57 or KS-U58, set the external input setting to “EXT IN” (see page 25 of the INSTRUCTIONS).

Connecting the external components

Other external component

3.5 mm stereo mini plug

External component

*3 Remote lead

*4 Firmly attach the ground wire to the metallic ody or to the chassis of the car—to the place uncoated with paint (if coated with paint, remove the paint efore attaching the wire). Failure to do so may cause damage to the unit.

*5 Signal cord

*6 JVC Bluetooth adapter

*7 Connecting cord supplied for your CD changer

*8 Interface adapter for iPod

*9 D. player interface adapter

*10 Line Input Adapter

*11 AUX Input Adapter

CD changer jack

with or without

External component

iPod is a trademark of Apple Inc., registered in the U.S. and other countries.