JVC KD-X220 User manual

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
FRANÇAIS
ESPAÑOL
B5A-0115-00 [J]
KD-X220
DIGITAL MEDIA RECEIVER
INSTRUCTION MANUAL
RÉCEPTEUR MULTIMÉDIA NUMÉRIQUE
MANUEL D’INSTRUCTIONS
RECEPTOR DE MEDIOS DIGITALES
MANUAL DE INSTRUCCIONES
Please read all instructions carefully before
operation to obtain the best possible performance
from the unit.
Veuillez lires les instructions attentivement avant
d’utiliser l’appareil afin d’obtenir les meilleures
performances possibles de l’appareil.
Por favor lea detenidamente este manual para
comprender a fondo todas las instrucciones y
obtener un máximo disfrute de esta unidad.
For customer Use:
Enter below the Model No. and Serial No. which are
located on the top or bottom of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
JS_JVC_KD_X220_J_C.indd 1JS_JVC_KD_X220_J_C.indd 1 24/9/2014 4:48:45 PM24/9/2014 4:48:45 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
CONTENTS BEFORE USE
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of
the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded
data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit, to prevent a short
circuit.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or
equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used
batteries promptly. If swallowed, contact a physician immediately.
BEFORE USE 2
BASICS 3
GETTING STARTED 4
USB / iPod / ANDROID 5
RADIO 7
AUX 8
Pandora® 9
iHeartRadio® 10
AUDIO SETTINGS 11
DISPLAY SETTINGS 13
MORE INFORMATION 14
TROUBLESHOOTING 15
SPECIFICATIONS 17
INSTALLATION /
CONNECTION 18 How to read this manual
• Operations are explained mainly using buttons on the faceplate.
• [
XX ] indicates the selected items.
• (
XX ) indicates references are available on the stated page.
Maintenance
Cleaning the unit: Wipe off dirt on the faceplate with a dry silicone or soft
cloth.
Cleaning the connector: Detach the faceplate and clean the connector
gently with a cotton swab, being careful not to damage the connector. Connector (on the reverse
side of the faceplate)
JS_JVC_KD_X220_J_EN_2.indd 2JS_JVC_KD_X220_J_EN_2.indd 2 11/9/2014 4:42:33 PM11/9/2014 4:42:33 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
3
ENGLISH
BASICS
To On the faceplate On the remote control
Turn on the power Press .
• Press and hold to turn off the power. —
Adjust the volume Turn the volume knob. Press or .
Press the volume knob to mute the sound or pause playback.
• Press again to cancel. Press to mute the sound or pause playback.
• Press again to cancel.
Select a source • Press repeatedly.
• Press , then turn the volume knob within 2 seconds.
• Press to select iPod or USB source directly.
Press SOURCE repeatedly.
Change the display
information
Press repeatedly. (
15 )—
Attach
How to reset
Detach
Your preset adjustments
will also be erased.
Remote control (RM-RK52)Faceplate
Volume knob
(turn/press) Display window
Detach button How to replace the battery
Pull out the insulation sheet
when using for the first time.
Remote sensor (Do not expose
to bright sunlight.)
JS_JVC_KD_X220_J_EN_2.indd 3JS_JVC_KD_X220_J_EN_2.indd 3 18/9/2014 9:55:02 AM18/9/2014 9:55:02 AM

4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
Cancel the demonstration
1 Press and hold .
2 Turn the volume knob to select [ DEMO ], then press the knob.
3 Turn the volume knob to select [ DEMOOFF ], then press the knob.
4 Press to exit.
Set the clock
1 Press and hold .
2 Turn the volume knob to select [ CLOCK ], then press the knob.
3 Turn the volume knob to select [ CLOCKSET ], then press the knob.
4 Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [ 24H/ 12H ], then press the knob.
6 Turn the volume knob to select [ 12 HOUR ] or [ 24 HOUR ], then press the
knob.
7 Press to exit.
To return to the previous setting item, press .
Set the basic settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected or activated.
4 Press to exit.
To return to the previous setting item, press .
1
2
Default: XX
SETTINGS
BEEP ON
:Activates the keypress tone.; OFF :Deactivates.
SRC SELECT
AM
* ON :Enables AM in source selection.; OFF :Disables.
PANDORA * ON :Enables PANDORA in source selection.; OFF :Disables.
IHEART * ON :Enables IHEARTRADIO in source selection.; OFF :Disables.
AUX * BTADAPTER :Selects when the KS-BTA100 Bluetooth adapter is
connected to the AUX jack. (
8 ); ON :Enables AUX in source selection.;
OFF :Disables.
F/W UPDATE
SYSTEM
F/W xxxx YES
:Starts upgrading the firmware.; NO :Cancels (upgrading is not
activated).
For details on how to update the firmware, see:
<http://www.jvc.net/cs/car/>.
CLOCK
CLOCK SYNC AUTO
:The clock time is automatically set using the Clock Time (CT) data
in FM Radio Broadcast Data System signal.;
OFF :Cancels.
CLOCK DISP ON :The clock time is shown on the display even when the unit is turned
off.;
OFF :Cancels.
* Not displayed when the corresponding source is selected.
3
JS_JVC_KD_X220_J_EN_2.indd 4JS_JVC_KD_X220_J_EN_2.indd 4 18/9/2014 9:55:04 AM18/9/2014 9:55:04 AM

ENGLISH 5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
USB / iPod / ANDROID
To On the faceplate On the remote control
Reverse / Fast-forward*3Press and hold . Press and hold .
Select a file Press .Press .
Select a folder*4Press . Press .
Repeat play*5Press repeatedly.
TRACK RPT / RPT OFF : JVC Playlist Creator (JPC) / JVC Music
Control (JMC) file (
14 )
TRACK RPT / FOLDER RPT / RPT OFF : MP3/WMA/WAV/FLAC file
ONE RPT / ALL RPT / RPT OFF : iPod or ANDROID
Random play*5Press repeatedly.
FOLDERRND / ALL RND / RND OFF : MP3/WMA/WAV/FLAC file or JPC / JMC
file
SONG RND / ALL RND / RND OFF : iPod or ANDROID
*1
Do not leave the cable inside the car when not using.
*2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the
application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
(
14 )
*3
For ANDROID: Applicable only when [ AUTO MODE ] is selected. ( 6 )
*4
Only for MP3/WMA/WAV/FLAC files. This does not work for iPod/ ANDROID.
*5
For iPod/ ANDROID: Applicable only when [ HEAD MODE ]/ [ AUTO MODE ] is selected. ( 6 )
Start playback
The source changes automatically and
playback starts.
USB input terminal
USB 2.0 cable
*1
(commercially available)
Micro USB 2.0 cable
*1
(commercially available)
(Accessory of the iPod/
iPhone)*
1
USB
iPod/iPhone
ANDROID*2
JS_JVC_KD_X220_J_EN_2.indd 5JS_JVC_KD_X220_J_EN_2.indd 5 18/9/2014 9:55:05 AM18/9/2014 9:55:05 AM

6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
To On the faceplate
Select control
mode
While in iPod source, press repeatedly.
HEAD MODE : Control from the unit.
IPHONE MODE : Control from the iPod/iPhone. However, you
can still play/pause or file skip from the unit.
While in ANDROID source, press
repeatedly.
AUTO MODE : Control from the unit (using JVC MUSIC
PLAY application).
AUDIO MODE : Control other media player applications
from the Android device (without using JVC
MUSIC PLAY application). However, you can
still play/pause or file skip from the unit.
Select music
drive
Press repeatedly.
The stored songs in the following start playback.
• Selected internal or external memory of a smartphone
(Mass Storage Class).
• Selected drive of a multiple drives device.
Change the playback speed of the Audiobook
While listening to the iPod and [ HEADMODE ] is selected ( Select control mode )....
1 Press and hold .
2 Turn the volume knob to select [ IPOD ], then press the knob.
3 Press the volume knob to select [ AUDIOBOOKS ].
4 Turn the volume knob to make a selection, then press the knob.
0.5×SPEED / 1×SPEED / 2×SPEED : Select the desired playback speed of the
Audiobooks sound file in your iPod/iPhone.
(Default: Depends on your iPod/iPhone setting.)
5 Press to exit.
To return to the previous setting item, press .
Select a file from a folder/list
1 Press .
2 Turn the volume knob to select a folder/list, then press the
knob.
3 Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
For MP3/WMA/WAV/FLAC or JPC / JMC file:
Turn the volume knob quickly.
For iPod:
You can search for a file according to the first character.
Press or turn the volume knob quickly to select the
desired character (A to Z/ 0to9/ OTHERS).
• Select “OTHERS” if the first character is other than Ato Z,
0 to 9.
• To return to the previous setting item, press .
• To cancel, press and hold .
• For iPod, applicable only when [
HEADMODE ] is selected. (  Select
control mode
)
• For ANDROID, applicable only when [
AUTO MODE ] is selected.
(
Select control mode )
USB / iPod / ANDROID
JS_JVC_KD_X220_J_EN_2.indd 6JS_JVC_KD_X220_J_EN_2.indd 6 11/9/2014 4:42:37 PM11/9/2014 4:42:37 PM

ENGLISH 7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
1 Press repeatedly to select FM or AM.
2 Press (or press on RM-RK52) to search for a station automatically.
(or)
Press and hold (or press and hold on RM-RK52) until “M” flashes,
then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1to 6).
(or)
1 Press and hold the volume knob until “PRESETMODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Select a stored station
Press one of the number buttons (1to6).
(or)
1 Press
2 Turn the volume knob to select a preset number, then press the knob to
confirm.
Other settings
1 Press and hold .
2 Turn the volume knob to select [ TUNER ], then press the
knob.
3 Turn the volume knob to make a selection ( see the
following table
) , then press the knob.
4 Repeat step 3until the desired item is selected/
activated or follow the instructions stated on the
selected item.
5 Press to exit.
To return to the previous setting item, press .
Default: XX
RADIO TIMER Turns on the radio at a specific time regardless of the
current source.
1 ONCE / DAILY / WEEKLY / OFF :Select how often the
timer will be turned on.
2 FM / AM :Select the source.
3 01 to 18 (for FM)/ 01 to 06 (for AM):Select the preset
station.
4 Set the activation day*
1
and time.
“
M ” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [
OFF ] is selected for [ AM ] in [ SRCSELECT ] after Radio
Timer for AM is selected. (
4 )
*1
Selectable only when [ ONCE ] or [ WEEKLY ] is selected in step 1 .
JS_JVC_KD_X220_J_EN_2.indd 7JS_JVC_KD_X220_J_EN_2.indd 7 18/9/2014 9:55:12 AM18/9/2014 9:55:12 AM

8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
Use a portable audio player
1 Connect a portable audio player (commercially available).
2 Select [ ON ] for [ AUX ] in [ SRC SELECT ]. ( 4 )
3 Press repeatedly to select AUX.
4 Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio
output.
Use a Bluetooth® device
1 Connect the Bluetooth adapter, KS-BTA100 (separately purchased).
2 Register (pair) the Bluetooth device with KS-BTA100.
3 Select [ BT ADAPTER ] for [ AUX ] in [ SRC SELECT ]. ( 4 ).
4 Press repeatedly to select BT AUDIO.
5 Start using the Bluetooth device.
For details, refer to the instruction manual of KS-BTA100.
3.5mm (1/8") stereo mini plug with “L” shaped connector
(commercially available)
Portable audio player
Auxiliary input jack
AUX
Auxiliary input jack
Blue/white Blue/white: Remote
Black Black: Ground
Brown Brown: Tel muting
Wiring harness of the unit
(
19 )
Default: XX
SSM SSM01–06 / SSM07–12 / SSM13–18 :Automatically presets up
to 18 stations for FM. “SSM” stops flashing when the first 6 stations are
stored. Select
SSM07–12 / SSM13–18 to store the following 12
stations.
IF BAND AUTO :Increases the tuner selectivity to reduce interference noises from
adjacent FM stations. (Stereo effect may be lost.);
WIDE :Subjects to
interference noises from adjacent FM stations, but sound quality will not
be degraded and the stereo effect will remain.
MONO ON :Improves the FM reception, but the stereo effect will be lost.;
OFF :Cancels.
AREA AREAUS : For North/Central/South America, AM/FM intervals:
10kHz/200kHz.;
AREASA :For some South American countries, AM/
FM intervals: 10kHz/50kHz.;
AREAEU :For any other areas, AM/FM
intervals: 9kHz/50kHz.
PTY SEARCH *2 Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you
have selected, that station is tuned in.
PTY code : NEWS , INFORM (information), SPORTS , TALK , ROCK , CLSROCK (classic
rock),
ADLTHIT (adult hits), SOFTRCK (softrock), TOP40 , COUNTRY , OLDIES , SOFT ,
NOSTALGA (nostalgia), JAZZ , CLASSICL (classical), R&B (rhythm and blues),
SOFTR&B (soft rhythm and blues), LANGUAGE , RELMUSC (religious music),
RELTALK (religious talk), PERSNLTY (personality), PUBLIC , COLLEGE , HABLESP
(Spanish talk),
MUSCESP (Spanish music), HIPHOP , WEATHER
*2
Only for FM source.
JS_JVC_KD_X220_J_EN_2.indd 8JS_JVC_KD_X220_J_EN_2.indd 8 11/9/2014 4:42:39 PM11/9/2014 4:42:39 PM

ENGLISH 9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [
ON ] for [ PANDORA ] in [ SRC SELECT ]. ( 4 )
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
The source changes to PANDORA and broadcast starts.
To On the faceplate On the remote control
Playback / pause Press the volume knob. Press .
Skip a track Press T. Press I.
Thumbs up or
thumbs down*2
Press . Press .
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Create and save a new station
1 Press .
2 Turn the volume knob to select [ NEW STATION ], then press the knob.
3 Turn the volume knob to select [ FROM TRACK ] or [ FROM ARTIST ], then
press the knob.
A new station is created based on the current song or artist.
4 Press and hold number button 1, 4, 5or 6to store.
To select a stored station, press number button 1, 4, 5or 6.
Search for a registered station
1 Press .
2 Turn the volume knob to make a selection, then press the knob.
[
BYDATE ]: According to the registered date.
[
A-Z ]: Alphabetical order.
3 Turn the volume knob to the desired station, then press the knob.
To cancel, press and hold .
Bookmark a song or artist information
1 Press and hold the volume knob.
2 Turn the volume knob to make a selection, then press the knob.
[
THIS TRACK ]: Current song information
[
THIS ARTIST ]: Current artist information
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this
unit.
USB input terminal
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_X220_J_EN_2.indd 9JS_JVC_KD_X220_J_EN_2.indd 9 11/9/2014 4:42:39 PM11/9/2014 4:42:39 PM

10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iHeartRadio®
Preparation:
Install the latest version of iHeart Link for JVC application on your device (iPhone/ iPod
touch), then create an account and log in to iHeartRadio.
• Select [
ON ] for [ IHEART ] in [ SRC SELECT ]. ( 4 )
Start listening
1 Open the iHeart Link application on your device.
2 Connect your device to the USB input terminal.
3 Press repeatedly to select IHEARTRADIO.
Broadcast starts automatically
To On the faceplate On the remote control
Playback / pause Press the volume knob. Press .
Skip a track for custom station Press T. Press I.
Thumbs up or thumbs down
for custom station*2
Press . Press .
Create a new/custom station Press and hold the volume
knob.
—
Add to favorite stations for live
station
Press 1.—
Scan for live station Press 4.—
*1
Do not leave the cable inside the car when not using.
*2
If thumbs down is selected, the current track is skipped.
Search for a station
1 Press .
2 Turn the volume knob to select a category, then
press the knob.
3 Turn the volume knob to the desired station, then
press the knob.
When a city list appears, you can skip cities in
alphabetical order.
To cancel, press and hold .
Skip cities by alphabetical order
While a city list appears during search...
1 Turn the volume knob quickly to enter character
search.
You can search through the list quickly according to
the first character (A to Z).
2 Turn the volume knob or press to select the
character to be search for.
3 Press the volume knob to start searching.
To cancel, press and hold .
USB input terminal
(Accessory of the iPod/iPhone)
*1
JS_JVC_KD_X220_J_EN_2.indd 10JS_JVC_KD_X220_J_EN_2.indd 10 11/9/2014 4:42:39 PM11/9/2014 4:42:39 PM

ENGLISH 11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
Default: XX
EQSETTING
EQPRESET FLAT
/ HARD ROCK / JAZZ / POP / R&B / TALK / USER1 / USER2 /
VOCALBOOST / BASSBOOST / CLASSICAL / DANCE :Selects a preset
equalizer.
EASYEQ 1 USER1 / USER2 :Select a preset name.
2 Adjust your own sound settings.
SUB.W SP
*1*2
: 00 to +06 (Default: 03
SUB.W
*1*3
: –08 to +08 00
BASS  LVL : –06 to +06 00
MID  LVL: –06 to +06 00
TRE  LVL : –06 to +06 00 )
PRO EQ 1 USER1 / USER2 :Select a preset name.
2 BASS / MIDDLE / TREBLE :Select a sound tone.
3 Adjust the sound elements of the selected sound tone.
BASS Frequency: 60 / 80 / 100 / 200HZ
(
Default: 80HZ
Level: –06 to +06 00
Q: Q1.0 / Q1.25 / Q1.5 / Q2.0 Q1.0 )
MIDDLE Frequency: 0.5 / 1.0 / 1.5 / 2.5KHZ (Default: 1.0KHZ
Level: –06 to +06 00
Q: Q0.75 / Q1.0 / Q1.25 Q1.25 )
TREBLE Frequency: 10.0 / 12.5 / 15.0 / 17.5KHZ (Default: 10.0KHZ
Level: –06 to +06 00
Q: QFIX QFIX )
*1
Displayed only when [ SUB.W ] is set to [ ON ]. (  12 )
*2
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ]. (  12 )
*3
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ]. (  12 )
To On the faceplate
Select a preset
equalizer
Press repeatedly.
Press , then turn the volume knob
within 2seconds.
Preset equalizer : FLAT (default), HARD ROCK , JAZZ , POP ,
R&B , TALK , USER1 , USER2 , VOCAL BOOST , BASS BOOST ,
CLASSICAL , DANCE
Store your own
sound settings
1 Press and hold .
2 Turn the volume knob to select [ EASY EQ ], then
press the knob.
3 Turn the volume knob to select [ USER1 ] or
[
USER2 ], then press the knob.
4 Turn the volume knob to make a selection,
then press the knob.
For settings, refer to step 2of [
EASYEQ ].
• To return to the previous setting item, press .
• To exit, press .
Other settings
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
JS_JVC_KD_X220_J_EN_2.indd 11JS_JVC_KD_X220_J_EN_2.indd 11 11/9/2014 4:42:40 PM11/9/2014 4:42:40 PM

12
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO
BASS BOOST +01
/ +02 : Selects your preferred bass boost level.; OFF :Cancels.
LOUD 01 / 02 :Boosts low or high frequencies to produce a well-balanced
sound at low volume.;
OFF :Cancels.
SUB.W LEVEL
*4
SPK-OUT
*5
00 to +06 ( +03 ):Adjusts the output level of the
subwoofer connected via speaker lead. (
 19 )
PRE-OUT
*6
–08 to +08 ( 00 ):Adjusts the output level of the
subwoofer connected to the lineout terminals (REAR/
SW) through an external amplifier. (
 19 )
SUB.W
*6
ON / OFF : Turns on or off the subwoofer output.
SUB.W  LPF
*4
THROUGH :All signals are sent to the subwoofer. ; LOW  55HZ /
MID  85HZ / HIGH120HZ :Audio signals with frequencies lower than
55Hz/ 85Hz/ 120Hz are sent to the subwoofer.
SUB.WPHASE
*4
REVERSE (180°)/ NORMAL (0°):Selects the phase of the subwoofer
output to be in line with the speaker output for optimum performance.
(Selectable only if a setting other than [
THROUGH ] is selected for
[
SUB.W  LPF ].)
FADER R06 — F06 ( 00 ):Adjusts the front and rear speaker output balance.
BALANCE
*7
L06 — R06 ( 00 ):Adjusts the left and right speaker output balance.
VOL ADJUST –05 — +05 ( 00 ):Presets the volume adjustment level of each source
(compared to the FM volume level). Before adjustment, select the source
you want to adjust. (“VOLADJFIX” appears if FM is selected.)
AMP GAIN LOW  POWER :Limits the maximum volume level to 30. (Select if the
maximum power of each speaker is less than 50W to prevent damaging
the speakers.);
HIGHPOWER :The maximum volume level is 50.
D.T.EXP
(Digital Track
Expander)
ON :Creates realistic sound by compensating the high-frequency
components and restoring the rise-time of the waveform that are lost in
audio data compression.;
OFF :Cancels.
TEL  MUTING
*8
ON :Mutes the sounds while using the cellular phone (not connected
through KS-BTA100).;
OFF :Cancels.
SPK/PRE  OUT Selects the appropriate setting to get the desired output. ( See the
following table
.)
*4
Displayed only when [ SUB.W ] is set to [ ON ].
*5
Displayed only when [ SPK/PRE  OUT ] is set to [ SUB.W/SUB.W ].
*6
Displayed only when [ SPK/PRE  OUT ] is set to [ REAR/SUB.W ] or [ SUB.W/SUB.W ].
*7
This adjustment will not affect the subwoofer output.
*8
Does not work if [ BT  ADAPTER ] is selected for [ AUX ] in [ SRC  SELECT ]. (  4 )
SPK/PRE OUT
Setting Lineout terminal Rear speaker lead
REAR/SW L (left) R (right)
REAR/REAR Rear speakers output Rear speakers output Rear speakers output
REAR/SUB.W Subwoofer output Rear speakers output Rear speakers output
SUB.W/SUB.W Subwoofer output Subwoofer output (Mute)
If [ SUB.W/SUB.W ] is selected:
– [
HIGH120HZ ] is selected in [ SUB.W  LPF ] and [ THROUGH ] is not available.
– [
R01 ] is selected in [ FADER ] and selectable range is [ R06 ]to [ 00 ]
AUDIO SETTINGS
JS_JVC_KD_X220_J_EN_2.indd 12JS_JVC_KD_X220_J_EN_2.indd 12 11/9/2014 4:42:40 PM11/9/2014 4:42:40 PM

ENGLISH 13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BRIGHTNESS Sets the button, display and USB input terminal brightness for day and night
separately.
1 DAY / NIGHT :Select day or night.
2 Select a zone for setting. ( Illustration on left )
3 Set the brightness level ( 00 to 31 ). (Default: DAY : 31 ; NIGHT : 15 )
SCROLL * 2 ONCE :Scrolls the display information once.; AUTO :Repeats scrolling at
5-second intervals.;
OFF :Cancels.
[ NIGHTCOLOR ] or [ DAYCOLOR ] is changed by turning on or off your car’s
headlight.
*1
The illumination control wire connection is required. ( 19 )
*2
Some characters or symbols will not be shown correctly (or will be blanked).
1 Press and hold .
2 Turn the volume knob to make a selection (see the following table),
then press the knob.
3 Repeat step 2until the desired item is selected/activated or follow
the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: XX
DISPLAY
DIMMER
Selects the display and button illumination adjusted in the [ BRIGHTNESS ]
setting.
OFF :Selects the day adjustments.; ON :Selects the night adjustments.;
DIMMER TIME :Adjusts the dimmer on and off time.
Turn the volume knob to adjust the [
ON ] time, then press the knob.
Turn the volume knob to adjust the [
OFF ] time, then press the knob.
(Default: [
ON ]: 18:00 or 6:00 PM
[
OFF ]: 6:00 or 6:00 AM)
AUTO :Changes between the day and night adjustments when you turn off or
on the car headlights.*
1
DISPLAY SETTINGS
JS_JVC_KD_X220_J_EN_2.indd 13JS_JVC_KD_X220_J_EN_2.indd 13 11/9/2014 4:42:40 PM11/9/2014 4:42:40 PM

14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Playable files
• Playable audio file: MP3 (.mp3), WMA (.wma), WAV(.wav), FLAC (.flac)
• Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible
depending on the types or conditions of media or device.
About USB devices
• This unit can play MP3/WMA/WAV/FLAC files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5m may result in abnormal playback.
• The maximum number of characters for:
- Folder names: 64 characters
- File names: 64 characters
- MP3 Tag: 64 characters
- WMA Tag: 64 characters
- WAV Tag: 64 characters
- FLAC Tag: 64 characters
• This unit can recognize a total of 20 480 files, 999 folders (999 files per folder including folder
without unsupported files), and of 8 hierarchies.
• This unit cannot recognize a USB device whose rating is other than 5V and exceeds 1A.
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C
• It is not possible to browse video files on the “Videos” menu in
[HEAD MODE] .
• The song order displayed on the selection menu of this unit may differ from that of the iPod/
iPhone.
• If some operations are not performed correctly or as intended, visit:
<http://www.jvc.net/cs/car/>.
MORE INFORMATION
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS4.1 and above) may not fully support Android Open Accessory
(AOA)2.0.
• If the Android device supports both mass storage class device and AOA2.0, this unit always
playback via AOA2.0 as priority.
• For more information and the latest compatible list, see: <http://www.jvc.net/cs/car/>.
About Pandora
• Pandora is available only in the U.S., Australia and New Zealand.
• Because Pandora is a third-party service, the specifications are subject to change without
prior notice. Accordingly, compatibility may be impaired, or some or all of the services may
become unavailable.
• Some functions of Pandora cannot be operated from this unit.
• For issues using the application, please contact Pandora at [email protected].
About iHeartRadio
• iHeartRadio® is a third-party service, therefore the specifications are subject to change
without prior notice. Accordingly, compatibility may be impaired or some or all of the
services may become unavailable.
• Some iHeartRadio® functionality cannot be operated from this unit.
About JVC Playlist Creator and JVC Music Control
• This unit supports the PC application JVC Playlist Creator and Android
TM
application JVC Music
Control.
• When you play audio file with song data added using the JVC Playlist Creator or JVC Music
Control, you can search for audio file by Genres, Artists, Albums, Playlists, and Songs.
• JVC Playlist Creator and JVC Music Control are available from the following web site:
<http://www.jvc.net/cs/car/>.
JS_JVC_KD_X220_J_EN_2.indd 14JS_JVC_KD_X220_J_EN_2.indd 14 11/9/2014 4:42:40 PM11/9/2014 4:42:40 PM

ENGLISH 15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Change the display information
Press repeatedly.
FM or AM Station name (PS)*
1
Frequency Program type (PTY)*
1
*
2
Title*
1
*
2
Day/Clock (back to the beginning)
*1
For FM Radio Broadcast Data System stations only.
*2
If unavailable, “NO PTY” / “NO TEXT” appears.
USB Playing time Day/Clock Album title/Artist*
3
Track title*
3
Folder/file name (back to the beginning)
*3
If not recorded, “NO NAME” appears.
USB-IPOD
USB-ANDROID
Playing time Day/Clock Album title/Artist*
4
Track title*
4
(back to the beginning)
*4
If not recorded, “NO NAME” appears.
PANDORA Station name Album title/Artist Track title Playing time
Day/Clock (back to the beginning)
IHEART Station name Track title*
5
Track Artist*
5
Day/Clock (back
to the beginning)
*5
If unavailable, station name appears.
AUX AUX Day/Clock
BT AUDIO BT AUDIO Day/Clock
Symptom Remedy
General
Sound cannot be heard. • Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHECK WIRING
THEN PWR ON” appears.
Turn the power off, then check to be sure the terminals
of the speaker wires are insulated properly. Turn the
power on again.
“PROTECTING SEND
SERVICE” appears.
Send the unit to the nearest service center.
Source cannot be selected. Check the [
SRCSELECT ] setting. ( 4 )
Radio
• Radio reception is poor.
• Static noise while listening
to the radio.
• Connect the antenna firmly.
• Pull the antenna out all the way.
USB / iPod
Playback order is not as
intended.
The playback order is determined by the file name
(USB).
Elapsed playing time is not
correct.
This depends on the recording process earlier.
“NOT SUPPORT” appears and
file skips.
Check whether the file is a playable format. (
14 )
“READING” keeps flashing. • Do not use too many hierarchical levels and folders.
• Reattach the USB device.
“CANNOT PLAY” flashes and/
or connected device cannot
be detected.
• Check whether the connected device is compatible with
this unit and ensure the files are in supported formats.
( 14)
• Reattach the device.
The iPod/iPhone does not
turn on or does not work.
• Check the connection between this unit and iPod/
iPhone.
• Detach and reset the iPod/iPhone using hard reset.
Correct characters are not
displayed.
This unit can only display uppercase letters, numbers,
and a limited number of symbols.
TROUBLESHOOTINGMORE INFORMATION
JS_JVC_KD_X220_J_EN_2.indd 15JS_JVC_KD_X220_J_EN_2.indd 15 11/9/2014 4:42:40 PM11/9/2014 4:42:40 PM

16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy
Pandora
“CONNECT ERR” Communication is unstable.
“RATING ERR” Registration of thumbs up/thumbs down has failed.
“LICENSE ERR” You try to access from a country which Pandora is not
deliverable.
iHeartRadio
Station cannot be selected. If “Explicit Content” in [Account Settings] is checked in
the web version of iHeartRADIO, custom stations become
unavailable.
“CREATE ERR” Custom station name creation is unsuccessful.
“SAVE ERROR” Addition to the favorite category failed.
“DISCONNCTED” Check the connection to the device.
“NOSKIPS” The skip limit has been reached. Retry later.
“NOSTATIONS” No stations are found.
“NOT CONNCTD” Link to the application is impossible.
“UPDATE APP” Make sure you have installed the latest version of the
iHeart Link for JVC application on your device.
“PLS LOGIN” You haven’t log in. Log in again.
“STATION NOT AVAILABLE” Broadcast from the station is over.
“STATION NOT SELECTED” No station is selected.
“STREAM ERR” Broadcast data is interrupted.
“THUMBS ERR” Registration of Thumbs Up/Down has failed.
“TIMED OUT” The request has resulted in time-out.
If you have any troubles, try the following:
1 Check TROUBLESHOOTING
2 Reset the unit ( 3)
3 Contact (USA only)
Call: 1-800-252-5722 ( or ) visit: http://www.jvc.com
Symptom Remedy
ANDROID
• Sound cannot be heard
during playback.
• Sound output only
from the Android
device.
• Reconnect the Android device.
• If in [
AUDIO MODE ], launch any media player application
on the Android device and start playback.
• If in [
AUDIO MODE ], relaunch the current media player
application or use another media player application.
• Restart the Android device.
• If this does not solve the problem, the connected Android
device is unable to route the audio signal to unit. (
14 )
Cannot playback at
[
AUTO MODE ].
• Make sure JVC MUSIC PLAY APP is installed on the Android
device. ( 5 )
• Reconnect the Android device and select the appropriate
control mode. (
6 )
• If this does not solve the problem, the connected Android
device does not support [
AUTO MODE ]. ( 14 )
“NO DEVICE” or
“READING” keeps
flashing.
• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android
device does not support [
AUTO MODE ]. ( 14 )
Playback is intermittent
or sound skips.
Turn off the power saving mode on the Android device.
“CANNOT PLAY” • Make sure Android device contains playable audio files.
• Reconnect the Android device.
• Restart the Android device.
Pandora
“ADDERROR”
“SEARCHERR”
New station creation is unsuccessful.
“CHKDEVICE” Check the Pandora application on your device.
“NOSKIPS” The skip limit has been reached.
“NOSTATIONS” No stations are found.
“STATIONLMT” The number of registered stations has reached its limit.
Retry after deleting unnecessary stations from your device.
“UPGRADEAPP” Make sure you have installed the latest version of the
Pandora application on your device.
JS_JVC_KD_X220_J_EN_2.indd 16JS_JVC_KD_X220_J_EN_2.indd 16 11/9/2014 4:42:42 PM11/9/2014 4:42:42 PM

ENGLISH 17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SPECIFICATIONS
Tuner
FM Frequency Range 87.9MHz — 107.9MHz (200kHz step)
87.5MHz — 108.0MHz (50kHz step)
Channel Space Selection 50kHz/200kHz
Usable Sensitivity (S/N=26dB) 8.2dBf (0.71μV/75Ω)
Quieting Sensitivity (DINS/N=46dB) 17.2dBf (2.0μV/75Ω)
Frequency Response (±3dB) 30Hz — 15kHz
Signal-to-Noise Ratio (MONO) 64dB
Stereo Separation (1kHz) 40dB
AM Frequency Range 530kHz — 1700kHz (10kHz step)
531kHz — 1611kHz (9kHz step)
Channel Space Selection 9kHz/10kHz
Usable Sensitivity (S/N=20dB) 29dBμ (28.2μV)
USB
USB Standard USB1.1, USB2.0 (Full speed)
Compatible Devices Mass storage class
File System FAT12/16/32
Maximum Supply Current DC5V 1A
D/A Converter 24 Bit
Frequency Response (±1dB) 20Hz — 20kHz
Signal-to-Noise Ratio (1kHz) 105dB
Dynamic Range 88dB
Channel Separation 90dB
MP3 Decode Compliant with MPEG-1/2 Audio Layer-3
WMA Decode Compliant with Windows Media Audio
WAV Decode RIFF waveform Audio Format (Linear
PCM only)
FLAC Decode FLAC files
Auxiliary

Frequency Response (±3dB) 20Hz—20kHz
Input Maximum Voltage 1000mV
Input Impedance 30kΩ
Audio
Maximum Output Power 50W×4 or
50W×2 + 50W×1 (Subwoofer = 4Ω)
Full Bandwidth Power
(at less than 1% THD)
22W×4
Speaker Impedance 4Ω—8Ω
Preout Level/Load (USB) 2500mV/10kΩ
Preout Impedance ≤600Ω
General
Operating Voltage
(10.5V—16V allowable)
14.4V
Maximum Current Consumption 10A
Operating Temperature Range 0°C to +40°C
Installation Size (W×H×D) 182mm×53mm×108mm
(7-3/16"×2-1/8"×4-5/16")
Weight 0.58k
g (1.3lbs)
Subject to change without notice.
JS_JVC_KD_X220_J_EN_2.indd 17JS_JVC_KD_X220_J_EN_2.indd 17 11/9/2014 4:42:42 PM11/9/2014 4:42:42 PM

18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Warning
• The unit can only be used with a 12V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car
chassis or Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the
car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts
of this unit during and shortly after use of the unit. Metal parts such as the
heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire
(black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50W. If the
maximum power of the speakers is lower than 50W, change the
[AMPGAIN] setting to avoid damaging the speakers. (  12 )
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect
Ignition wire (red) to the terminal on the vehicle’s fuse box which provides
12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers,
etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis,
then replace the old fuse with one that has the same rating.
Basic procedure
1 Remove the key from the ignition switch, then
disconnect the terminal of the car battery.
2 Connect the wires properly.
See Wiring connection. ( 
19 )
3 Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Reset the unit. (  3 )
INSTALLATION / CONNECTION
How to remove the unit
Bracket (not supplied)
Pocket
Flat or round head screws
(not supplied)
M5 × 8mm (M5 × 3/8")
Do the required wiring.
(  19)
Bend the appropriate tabs to
hold the sleeve firmly in place.
Hook on the top side
Orientate the trim plate as
illustrated before fitting. Dashboard of
your car
Installing the unit (in-dash mounting)
When installing without the mounting
sleeve
Use only the specified screws. Using wrong screws
might damage the unit.
JS_JVC_KD_X220_J_EN_2.indd 18JS_JVC_KD_X220_J_EN_2.indd 18 11/9/2014 4:42:42 PM11/9/2014 4:42:42 PM

ENGLISH 19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Part list for
installation
(A) Faceplate
(C) Mounting sleeve
(B) Trim plate
(D) Wiring harness
(E) Extraction key
STEERING
WHEEL
REMOTE
Wiring connection
Car fuse block
Ignition switch
Recommended
connection
Vehicle-specific Wiring
Harness (separately
purchased)
For more information:
Metra Electronics:
www.metraonline.com
Scosche Industries:
www.scosche.com
Blue/white: To amplifier
Blue: To power antenna
Make this connection if
your vehicle factory wiring
harness does not have
“12V ignition switch” wire.
Separate red wire
Signal cord (not supplied)
Remote wire
(not supplied)
Fuse (10A) Antenna terminalRear/subwoofer output
Factory wiring
harness (vehicle)
Vehicle dashboard
Black: Ground
Yellow: Battery 12V
White: Front speaker (left)
White/black
Gray: Front speaker (right)
Gray/black
Green: Rear speaker (left)
* 2
Green/black * 2
Purple: Rear speaker (right)
Purple/black
Join the same color wires together.
Red: Ignition 12V
Orange/white: Illumination
Brown: Tel muting
Blue/white: Remote (200mA max.)
Light blue/yellow To the steering wheel
remote control adapter
*2
You can also connect a
subwoofer speaker directly
using this lead without an
external subwoofer amplifier.
For setting, 
12 .
JVCAmplifier
* 1
*1
Firmly connect the ground wire of the amplifier to the
car’s chassis to avoid damaging the unit.
JS_JVC_KD_X220_J_EN_2.indd 19JS_JVC_KD_X220_J_EN_2.indd 19 11/9/2014 4:42:43 PM11/9/2014 4:42:43 PM

Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
2
TABLE DES MATIERES AVANT L’UTILISATION
Avertissement
N’utilisez aucune fonction qui risque de vous distraire de la conduite sure de votre véhicule.
Précautions
Réglage du volume:
• Ajustez le volume de façon à pouvoir entendre les sons extérieurs à la voiture afin d’éviter tout risque d’accident.
• Réduisez le volume avant de reproduire des sources numériques afin d’éviter d’endommager les enceintes par la soudaine
augmentation du niveau de sortie.
Généralités:
• Éviter d’utiliser le périphérique extérieur s’il peut gêner une conduite en toute sécurité.
• Assurez-vous que toutes les données importantes ont été sauvegardées. Nous ne pouvons pas être tenu responsable pour toute
perte des données enregistrées.
• Veuillez faire en sorte de ne jamais mettre ou laisser d’objets métalliques (tels que des pièces ou des outils) dans l’appareil, afin
d’éviter tout risque de court-circuit.
Télécommande (RM-RK52):
• Ne laissez pas la télécommande dans des endroits exposés à la chaleur, comme sur le tableau de bord par exemple.
• La pile au lithium risque d’exploser si elle est remplacée incorrectement. Ne la remplacez uniquement qu’avec le même type de
pile ou son équivalent.
• Le boîtier de la pile ou les piles ne doivent pas être exposés à des chaleurs excessives telles que les rayons du soleil, du feu, etc.
• Gardez la pile hors de la portée des enfants et dans son emballage d’origine quand elle n’est pas utilisée. Débarrassez-vous des
piles usagées rapidement. En cas d’ingestion, contactez un médecin immédiatement.
AVANT L’UTILISATION 2
FONCTIONNEMENT DE BASE 3
PRISE EN MAIN 4
USB / iPod / ANDROID 5
RADIO 7
AUX 8
Pandora® 9
iHeartRadio® 10
RÉGLAGES AUDIO 11
RÉGLAGES D’AFFICHAGE 13
PLUS D’INFORMATIONS 14
GUIDE DE DÉPANNAGE 15
SPÉCIFICATIONS 17
INSTALLATION /
RACCORDEMENT 18
Comment lire ce manuel
• Les opérations sont expliquées principalement en utilisant les touches de la façade.
• [
XX ] indique les éléments choisis.
• (
XX ) indique que des références sont disponibles aux page citées.
Entretien
Nettoyage de l’appareil: Essuyez la saleté de la façade avec un chiffon sec au silicone ou
un chiffon doux.
Nettoyage du connecteur: Détachez la façade et nettoyez le connecteur à l’aide d’un
coton tige en faisant attention de ne pas endommager le connecteur. Connecteur (sur la face arrière
de la façade)
JS_JVC_KD_X220_J_FR.indd 2JS_JVC_KD_X220_J_FR.indd 2 23-Sep-14 2:35:05 PM23-Sep-14 2:35:05 PM