JWA 70458 User manual

1
ASSEMBLY INSTRUCTION
ITEM CODE 70458
ELCHE BUFFET
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
800MM
1600MM
395MM

Allow 30 min For 2 person AddiƟonal tools required
2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liŌing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucƟons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over Ɵghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucƟons for future reference.

3














 





1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PARTS LIST
A
16pcs
B
14pcs
C
26pcs
M8X30mmM15X12mmM7X39mm
M6X25mm M6X30mm M6X30mm
M6X30mm
M5X40mm
D
FGH
KL
30pcs
M3.5X14mm
1pcs 2pcs
6pcs 6pcs 4pcs
E
J
I
1pcs
6pcs
21pcs
OP
2pcs 2pcs
M12X10mm
N
M
1pcs
8pcs
M4x30mm M3.5x14mm
TOP PANEL
TOP PANEL
SIDE PANEL
SIDE PANEL
SUPPORT PANEL
SUPPORT PANEL
SHELF
SHELF
BOTTOM PANEL
BACK PANEL
DOOR
DOOR
METAL PARTS
METAL PARTS
METAL PARTS
METAL PARTS

4
STEP 1:
STEP 2:
=+
KK1 K2 K1
K1
DK2

A A
K


5
STEP 3:
STEP 4:


BBC
C



C
B
B
A
A
A
A




6
STEP 5:
STEP 6:
B
B
C
C
A
A





A
A


7
STEP 7:
STEP 8:


B
B
C
C


C
C
C
I
I
I
I
I







8
STEP 9:
STEP 10:
C
C
A
A
A
O
O
B
B
L
L




C
C
C
C
I
I
I







P
P
DD

9
STEP 11:
STEP 12:
G
G
G
G
GG
E


 

H
H
H
H




HH
!

10
STEP 13:
STEP 14:
E
F
F
F
FF







M
M
M
M




11
STEP 15:
STEP 16:
× 2
DD
D
D
 
J
J
J
J
D
D
D
D




12
ASSEMBLY COMPLETE

13
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
.'8*='8+
=GRR
(GIQYOJK
2GXMK9IXK]^=GRR9ZXGV^3U[TZOTM6RGZK^ 9SGRR9IXK]^
N

14
To protect your furniture, we suggest the following:
Avoid placing your furniture in direct sunlight.
Do not place furniture directly under windows.
Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
¿nish.
Do not place material with high temperature directly onto the
surface of your furniture.
Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe ¿nish
damage if not cleaned immediately.
Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the ¿nish.
NOTE: If the above care advise is not adhered to your product
warranty may become void