JWA CLEMENTINE 70186 User manual

1
ASSEMBLY INSTRUCTION
ITEM CODE 70186
CLEMENTINE BEDSIDE
Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
698MM
400MM
390MM

Allow 30 min For 2 person AddiƟonal tools required
2
PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may
damage the product
2. Take care when liŌing. Product should be assembled as near as possible to the
point of use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instrucƟons carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over Ɵghten the screws and bolts as this may damage the threads
7. Assembly is to be carried out by a competent adult(s) ONLY
8. During assembly, children should be kept away from the product due to possible
risk to injury.
9. Do not use this item if any components are missing or damaged.
10. Please keep the instrucƟons for future reference.

3
PARTS LIST
A
8pcs
B
8pcs
C
12pcs
M8X30mmM14.8X12mmM7X39mm M5X40mm
M3X16mm
M3.5X14mm
D
FGH
K
4pcs
M4X14mm
8pcs
20pcs 4pcs 2pcs
E
J
I
4pcs
1pcs
10pcs
N
M
1pcs
1pcs
L
1pcs
1
2
3
4
5
6
7
M4x30mm M3.5x14mm







SIDE PANEL
SIDE PANEL
SHELF
BOTTOM PANEL
TOP PANEL
DOOR
BACK PANEL

4
CAM LOCK INSTALL METHOD AS FOLLOWS
Step 1 Step 2
OR
Step 3
Fix cam nut into
the bottom of hole
then tighten it.
Lock
1.1cm
A

5
STEP 1:
STEP 2:
A
A


A
AA
BB
C
C
B




LI
I
L

6
STEP 3:
STEP 4:
D

C


E
F

FF
E

7
STEP 5:
STEP 6:
G
G
G
G

A A


B
B
N
N
C
C

8
STEP 7:

I
I

I
I
H
H
I
I
J

ŶŽƚŚĞƌĂƐƐĞŵďůLJŵĞƚŚŽĚŝƐƚŽĮdžŚŝŶŐĞƐŽŶƌŝŐŚƚ
ƐŝĚĞĂŶĚĮdžĚŽŽƌĐĂƚĐŚ;>ͿƚŽƚŚĞŽƉƉŽƐŝƚĞƉŽƐŝƟŽŶ

STEP 8:
9
ASSEMBLY COMPLETE
K
K
K


10
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
.'8*='8+
=GRR
(GIQYOJK
2GXMK9IXK]^=GRR9ZXGV^3U[TZOTM6RGZK^ 9SGRR9IXK]^
^
M