JWA HARDING 74708 User manual

Imported by JWA Furniture Pty Ltd, Qld, Brisbane Australia.
For any assistance with assembly or for missing parts please refer to your receipt
ASSEMBLY INSTRUCTION
1
74708
SOFA TABLE
HARDING
ITEM CODE
1200MM
350MM
750MM

PRE-ASSEMBLY PREPARATION
Before you start:
1.Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage the
product
2.Take care when lig. Product should be assembled as near as possible to the point of
use
3.Ensure that you have all required contents for complete assembly
4.Always read the assembly instrucns carefully before beginning assembly.
5.Keep all hardware parts and packaging out of reach of small children.
6.Do not over hten the screws and bolts as this may damage the threads
Allow 1 hour For 2 person Addinal tools required
2

PARTS LIST
3
1
X2
2
3
4
5
6
7
8
9
9
10
10
11
11
12
13
14 15
16
17

4
NO. ITEM QTY NO. ITEM QTY
A16PCS
B16PCS
C12PCS
D6PCS
E2PCS
F24PCS
H
2PCS
J
K2PCS
L8PCS
M
2PCS
I
2PCS
Φ6*35
Φ15*10
Φ6*30
Φ4*40
PARTS LIST
Φ3*12
G2PCS
1PC
Φ6*30
N4PCS
Φ3.5*12
O8PCS
P6PCS
Φ5*30
Q6PCS
Φ3*16
R8PCS
S3PCS
Φ6*12
Φ4*35
T10PCS

5
NO. ITEM QTY NO. ITEM QTY
PARTS LIST
NO. ITEM QTY NO. ITEM QTY
1TOP PANEL 1 PC
3
1 PC
1 PC
41 PC
51 PC
1 PC
1 PC
2 PCE
2 PCE
2 PCE
2LEFT SIDE PANEL
12
7
8
RIGHT SIDE PANEL
61 PC
11
13
14
15
16
2 PCE
2 PCE
2 PCE
2 PCE
2 PCE9
MIDDLE PANEL
BOTTOM PANEL
BACK PANEL
METAL LEG
METAL LEG
METAL LEG
10 METAL LEG
17 2 PCE
METAL LEG
DRAWER FRONT PANEL
DRAWER LEFT SIDE PANEL
DRAWER BACK PANEL
DRAWER RIGHT SIDE PANEL
DRAWER BOTTOM PANEL
DRAWER SUPPORT PANEL

STEP 1:
STEP 2:
6
A X6
1
A
F X6
A
A
A
A
A
H X1G X1
2
3
G
H
F
F
F
F
F
F

STEP 3:
STEP 4:
7
4
G
C X6
F X6H X1G X1
4
H
F
F
F
F
F
B X6
4
2
3
1
B
B
B
B
B
B
C
C
C
C
C
C

STEP 5:
STEP 6:
8
6
C
D X6
2
3
1
4
C X6
1
3
2
5
6
C
C
D
D
D
D
D
D

STEP 7:
STEP 8:
9
L X8M X1
M X1
7
10
M
L
L
L
L
L
L
L
L
8
10
9
9
S X3
M
M
M
S
S
S
S
S
11
11
10
10
7
9
9
8

STEP 9:
STEP 10:
10
O X8M X1
MR X8
R
R
R
R
R
R
R
R
O
OO
O
O
O
OO
X2
A X10B X10T X10K X2N X4
12
A
12
14
14
14
15
15
15
17
16
16
13
13
13
A
A
T
T
T
B
B
B
K
N

STEP 11:
STEP 12:
11
X2
J X2I X2F X12
I
12
13
J
F
F
F
F
F
F
12
12

STEP 13:
STEP 14:
12
P X6 Q X6
P
P
P
PP
P
Q
Q
Q2
QP
P
E X2
E
E
E
WALL
EE
E
EE
E

ASSEMBLY IS COMPLETE
13

14
SAFETY BRACKETS
INSTRUCTIONS
1. Attach one Mounting Plate to the wall with the Large Screws. Make sure to
attach the Mounting Plate into a stud. If mounting into brick or masonry you
will need to acquire wall anchors.
2. Attach the second Mounting Plate to the furniture frame with the Short
Screws.
3. Move the furniture to its final position. Thread a Wall Strap through the both
Mounting Plates and tighten until snug. Do not over tighten.
4. Make sure that the Mounting Plates are firmly attached to the wall and
furniture and that the Wall Strap is snug.
WALL
BACK SLDE
SCREWS X1 SCREWS X1Anti-tiit Strap X1 Expanded plastic pipe X1
HARDWARE
washer X2

To protect your furniture, we suggest the following:
• Avoid placing your furniture in direct sunlight.
• Do not place furniture directly under windows.
• Do not place sharp materials (knife, fork, etc.) directly onto
your furniture as sharp material may scrape and damage the
finish.
• Do not place material with high temperature directly onto the
surface of your furniture.
•Clean up spills quickly. Water left over a prolonged period of
time may cause damage. Alcohol, perfume, nail polishes,
aftershave and some medication may cause severe finish
damage if not cleaned immediately.
• Use a clean, soft, dry, lint free absorbent cloth to clean your
furniture. Do not use any detergent as they may contain
ingredients that may react and damage the finish.
NOTE: If the above care advise is not adhered to your product
warranty may become void
15